regulator_enable() is declared with __must_check attribute.
Hence check the return value to ensure that the regulator is enabled.
Fixes the following warning:
drivers/mmc/host/dw_mmc.c:2461:19: warning:
ignoring return value of ‘regulator_enable’, declared with attribute
warn_unused_result [-Wunused-result]
drivers/mmc/host/dw_mmc.c: In function ‘dw_mci_init_slot’:
drivers/mmc/host/dw_mmc.c:1994:19: warning:
ignoring return value of ‘regulator_enable’, declared with attribute
warn_unused_result [-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/mmc/host/sdhci-spear.c:295:12: warning: 'sdhci_suspend' defined but not used [-Wunused-function]
drivers/mmc/host/sdhci-spear.c:308:12: warning: 'sdhci_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When card is power-on/off, need to control the power-enable register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-pxav3 host controller used SDCLK for data timeout.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
1. seperate device tree parsing from platform data handling which
can make further work easy when platform data can be removed.
2. add calling mmc_of_parse which can parse more of property and
pxav3_get_mmc_pdata can be shrinked a lot.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Flag PXA_FLAG_CARD_PERMANENT is set in sdhci_pxa_platdata flags to
indicate that the card is always wired to host, like on-chip emmc,
which is permanently present and don't need detection.
So only MMC_CAP_NONREMOVABLE should be set for this case. But current
code also sets SDHCI_QUIRK_BROKEN_CARD_DETECTION, which doesn't make
sense.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci_pltfm_init can set host->ops and host->quirks if sdhci_pltfm_data
is transfered as arguments. Then no need to set them manually in
sdhci_pxav3_probe.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mci_writew causes a failure of fifo access for 64-bit.
mci_writeq is correct.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mvsdio driver was already using some dev_*() functions to print
some messages, but still using pr_*() functions for some others. This
patch converts all messages to use dev_*() functions.
Many of the pr_*() function calls were printing the output of
mmc_hostname() to preprend the message with an identifier for the
device. Since the dev_*() functions do that automatically, this patch
also gets rid of those string prefixes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ralph Droms <rdroms@gmail.com> reported that 3.9-rc was breaking the
SDIO interface on his Sheevaplug platform, and that the recent changes
to the mvsdio driver are responsible for this breakage. Precisely, the
regression has been introduced by 07728b77c0 (mmc: mvsdio: use
slot-gpio for card detect gpio).
After investigation, is turns out that the Sheevaplug does not have
any "card detect" GPIO, and the Sheevaplug has not been converted to
the Device Tree. Therefore, the Sheevaplug board code does not define
a value for the .gpio_card_detect field of the mvsdio_platform_data
structure, which means that its value is 0. Unfortunately,
gpio_is_valid() considers 0 as a valid GPIO, and therefore calls
mmc_gpio_request_cd(), which fails and makes the entire probing of the
driver fail.
In fact, in the previous mvsdio code, before the Device Tree binding
was introduced, 0 was not considered as a valid GPIO. Therefore, this
fix revert back to this behavior in the non-DT case, by setting the
gpio_card_detect and gpio_write_protect local variables to -EINVAL
when the corresponding fields of the mvsdio_platform_data structure
are set to zero (i.e, left undefined). Of course, it prevents to use
GPIO 0 as a card detect or write protect GPIO, but it was a defiency
of the previous non-DT code, and the fix moving forward is to convert
platforms to the Device Tree.
The problem has been reproduced successfully on the Kirkwood-based
Marvell DB-88F6281-BP Development Board (that doesn't use the Device
Tree) and the fix has proven to work properly, after of course
removing the gpio_card_detect field of the mvsdio_platform_data
instance for this board.
Reported-by: Ralph Droms <rdroms@gmail.com>
Tested-by: Ralph Droms <rdroms@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the new driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
All users of the sdhci_ops struct in the sdhci core already treat it as
const. The sdhci-pltfm code itself never actually looks at the ops field
of the sdhci_pltfm_data struct and merely passes it on to the sdhci core,
so make we can make it const in the sdhci_pltfm_data struct as well.
This allows us to declare sdhci_ops structs as const in drivers using
the sdhci-pltfm helper code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdhci_pltfm_data struct is never modified within the sdhci_pltfm
module. So make the pdata parameter to sdhci_pltfm_init and
sdhci_pltfm_register const. This allows drivers to declare their
sdhci_pltfm_data struct as const.
This patch also makes the sdhci_pltfm_data declarations const where
possible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix regression introduced by commit 796211b795 ("mmc: atmel-mci: add
pdc support and runtime capabilities detection") which removed the need
for CONFIG_MMC_ATMELMCI_DMA but kept the Kconfig-entry as well as the
compile guards around dma_release_channel() in remove(). Consequently,
DMA is always enabled (if supported), but the DMA-channel is not
released on module unload unless the DMA-config option is selected.
Remove the no longer used CONFIG_MMC_ATMELMCI_DMA option completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the compatible string for MSHC controller of Exynos4412.
And exynos5250_dwmmc_caps is renamed to exynos_dwmmc_caps, since it has the
capabilities of common features supported by Exynos4 and Exynos5.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use resource_size() instead of explicit calculation. This was found via
make coccicheck.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit f9c2a0dc42
"mmc: dw_mmc: Fix PIO mode with support of highmem" introduced
a regression since v3.2 making the mmc_test hang on test #13
with a "Data starvation by host timeout" interrupt.
This is because, sg_mapping_iter is used to iterate through the
data which spans on multiple pages. The problem is detected on
unaligned data submission where the code previously checked for
!(sg_next(host->sg)) which is true because we only have a single
scatter/gather list which then expands to multiple pages.
Therefore, the driver incorrectly assumed that this was the last
list item and submitted unaligned data to the mmc device. This
overflowed the FIFO on the device before all the data were written
to it. The code was fixed to only submit unaligned data when we are
handling the last sg_miter item by checking whether we reached
the desired data length or not.
The patch was tested against mmc_test and all the tests passed.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously, it was possible to add either 0 bytes or add nbytes
twice if we broke out of the outer loop and then carry on to the
"done" label. This is now fixed by adding the transferred bytes
right after the pull/pop operation
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is no reason to loop when handling an interrupt. The "if" clauses
will handle all of them sequentially. This also eliminates the extra loop
we used to take with no pending interrupts and we ended up breaking out
of the while loop.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
host->data_offset is initialised at the end of the probe function
depending on the VERID register, and is used for PIO operations. Move
this initialisation earlier, before IRQs or slots are initialised, to be
sure that PIO won't occur prior to host->data_offset being initialised.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Call the setpower platform callback in response to set_ios with
ios->power_mode == MMC_POWER_UP or MMC_POWER_OFF, instead of from the
card detect work function.
This appears to fix a problem I have where a card stuck in a funny state
doesn't get properly cleared by the power being turned off, presumably
due to lack of power sequencing. This resulted in the following log
messages after boot:
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 300000Hz, actual 298922HZ div = 167)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 200000Hz, actual 199680HZ div = 250)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 195765Hz, actual 195764HZ div = 255)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 400000Hz, actual 399360HZ div = 125)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 300000Hz, actual 298922HZ div = 167)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes:
/git/arm-soc/drivers/mmc/host/sdhci.c: In function 'sdhci_add_host':
/git/arm-soc/drivers/mmc/host/sdhci.c:2910:19: warning: ignoring
return value of 'regulator_enable', declared with attribute
warn_unused_result [-Wunused-result]
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Used resource_size function instead of explicit computation.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The variable 'mmc' is initialized but never used, so remove it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes timeout problems on t4240's sdhci controller:
mmc0: Too large timeout requested for CMD25!
mmc0: Too large timeout requested for CMD25!
mmc0: Too large timeout requested for CMD25!
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For some Realtek card readers, the power up sequence can only be executed
when power has been turned off fully.
So the rtsx host should not start power up sequence again when set_ios
been called if the power has been turned on.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
With device core now able to setup the default pin configuration,
the call to devm_pinctrl_get_select_default can be removed. And
the pin configuration code based on the deprecated Samsung specific
gpio bindings is also removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ACPI spec 5 defined the _ADR encoding for sdio bus as:
High word - slot number (0 based)
Low word - function number
This patch adds support for binding sdio function device with acpi node,
and if successful, involve acpi into its power management.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
1. mmc_rescan will call get_cd to know whether the card is present
before mmc_rescan_try_freq to avoid useless trials during
card removal or start host is called when card is not present.
2. get_cd needs to be checked to resolve slow card removal issue.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not return probe failure with missing DMA resources, allow driver
to work in PIO mode. Tested on da850-evm by mounting partition
followed by file creation and deletion.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the legacy code, driver clear not only UHS_REG 16 bit also 0-15bit.
If we use UHS-1 mode spec card like SDR50, SDR104. UHS_REG 0-15 should
be set by 1 according to slot id. In this case, legacy code can cause
problems.
In particular, UHS_REG consists of DDR_REG[31:16] and VOLT_REG[15:0].
Before adjusting this patch, bit[15:0] is always cleared.
Signed-off-by: Hyeonsu Kim <hyeonsu.kim@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In dwc manual, the below contents are described:
"During end of packet, interrupt is not generated if threshold
programming is larger than any remaining data. It is responsibility
of host to read remaining bytes on seeing Data Transfer Done
interrupt"
We also have seen the data cannot be read fully when
"sg_miter->length" is less than FIFO size.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Check the result of mmc_add_host() and return the value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use devm_clk_get() rather than clk_get() to make cleanup paths
more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the CD/WP-GPIOs are not provided by the SoC's GPIO controller,
we need to handle the case where omap_hsmmc is probed earlier than
the GPIO controller chosen in the device tree.
Fix this by checking the return value of of_get_named_gpio against
-EPROBE_DEFER and passing it through to the probe function.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Updating the sdhci-tegra driver to use mmc_of_parse to support standard
MMC DT bindings. Then we can remove the redundant code that already support
in generic MMC core.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In order to convert the Tegra MMC driver to using mmc_of_parse(), some
bugs in the Tegra device-tree content need to be fixed first; it's
currently wrong but unused, and mmc_of_parse() causes that data to be
used for the first time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=G8rC
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.10-fixes-for-mmc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into mmc-next
ARM: tegra: DT-related fixes needed by the MMC tree
In order to convert the Tegra MMC driver to using mmc_of_parse(), some
bugs in the Tegra device-tree content need to be fixed first; it's
currently wrong but unused, and mmc_of_parse() causes that data to be
used for the first time.
Silences the following sparse warning:
drivers/mmc/host/dw_mmc-exynos.c:218:5: warning:
symbol 'dw_mci_exynos_probe' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mmc controller on Tegra114 platforms is basically compatible with
the settings used for Tegra30. However there is a difference where we
don't need the extra ENABLE_SDHCI_SPEC_300 quirk as Tegra114 hardware
advertises v3.0 support already.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The structs wrapped with the SOC ifdefs are small enough where having
them always there shouldn't be a big overhead. Removing the ifdefs
also makes the code a little cleaner.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For better code reuse use the newly added page iterator to iterate
through the pages. The offset, length within the page is still
calculated by the mapping iterator as well as the actual mapping. Idea
from Tejun Heo.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=dYdW
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data consolidation,
OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee Jones. In
particular, the debugfs and the sysct interfaces got extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the twl-core
driver, with a much needed module id lookup code improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the palmas
GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra and
Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and ab9540 based
devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a better
card detection code path and now also supports the RTS5227 chipset, thanks
to Wei Wang and Roger Tseng.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BhC1
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Rework the driver to parse the device tree
directly into struct sdhci_tegra.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some SD/MMC interfaces use 2 power regulators: one to power the card itself
(Vcc) and another one to pull signal lines up (VccQ). In case of eMMC and
UHS SD cards the regulators also have to be configured to supply different
voltages. The preferred order of turning supply power on and off is to
turn Vcc first on and last off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
