There are several corner cases where driver might get a 2nd notification
about the same link change. Don't log any additional changes if the
physical carrier is already reported as it should.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a corner-case in HW where an SKB queued for transmission that
contains too many frags will cause FW to assert.
This patch solves this by linearizing the SKB if necessary.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device ID for the 10g module has changed. Populate the pci_ids table
accordingly.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the use of kobj_to_dev() helper function instead of open
coding it with container_of()
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@@
expression a;
symbol kobj;
@@
- container_of(a, struct device, kobj)
+ kobj_to_dev(a)
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW hsi contains regpairs, mostly for 64-bit address representations.
Since same paradigm is applied each time a regpair is filled, this
introduces a new utility macro for setting such regpairs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each configuration element send via ramrod requires a Slow Path Queue
entry. This slightly changes the way such an entry is configured, but
contains mostly semantic changes [where more parameters are gathered
in a sub-struct instead of being directly passed].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to HW design, some of the memories are wide-bus and access to those
needs to be sequentialized on a per-HW-block level; Read/write to a
given HW-block might break other read/write to wide-bus memory done at
~same time.
Status blocks initialization in CAU is done into such a wide-bus memory.
This moves the initialization into using DMAE which is guaranteed to be
safe to use on such memories.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial driver submission used GFP_ATOMIC almost inclusively when
allocating memory. We now remedy this point, using GFP_KERNEL where
it's possible.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device would start receiving only vlan-tagged traffic with tags matching
that of one of the configured vlan IDs, unless:
- Device is expliicly placed in PROMISC mode.
- Device exhausts its vlan filter credits.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, interfaces are working in vlan-promisc mode; But once
vlan filtering offloaded would be supported, we'll need a method to
control it directly [e.g., when setting device to PROMISC, or when
running out of vlan credits].
This adds the necessary API for L2 client to manually choose whether to
accept all vlans or only those for which filters were configured.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the qed* driver into utilizing the 8.7.3.0 FW.
This new FW is required for a lot of new SW features, including:
- Vlan filtering offload
- Encapsulation offload support
- HW ingress aggregations
As well as paving the way for the possibility of adding storage protocols
in the future.
V2:
- Fix kbuild test robot error/warnings.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since qlcnic_alloc_mbx_args can be failed,
return value should be checked.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qlcnic_dcb_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, if we succeeded on the last iteration through the
loop then we still returned failure.
Fixes: 389e4e04ad ('qlcnic: fix a timeout loop')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem here is that at the end of the loop we test for if
idc->vnic_wait_limit is zero, but since idc->vnic_wait_limit-- is a
post-op, it actually ends up set to (u8)-1. I have fixed this by
moving the decrement inside the loop.
Fixes: 486a5bc77a ('qlcnic: Add support for 83xx suspend and resume.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem here is that after the loop we test for "if (!i) " but
because "i--" is a post-op we exit with i set to -1. I have fixed this
by changing it to a pre-op instead. I had to change the starting value
from 3 to 4 so that we still iterate 3 times.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using INTa, ISR might be called before device is configured
for INTa [E.g., due to other device asserting the shared interrupt line],
in which case the ISR would read the SISR registers that shouldn't be
read unless HW is already configured for INTa. This might break interrupts
later on. There's also an MSI-X issue due to this difference, although
it's mostly theoretical.
This patch changes the initialization order, calling request_irq() for the
slowpath interrupt only after the chip is configured for working
in the preferred interrupt mode.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can't rely on pci config space to discover bar size,
as in some environments this returns a wrong, too large value.
Instead, rely on device register, which contains the value
provided by MFW at preboot.
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Concurrent non-blocking slowpath ramrods can be completed
out-of-order on the completion chain. Recycling completed elements,
while previously sent elements are still completion pending,
can lead to overriding of active elements on the chain. Furthermore,
sending pending slowpath ramrods currently lacks the update of the
chain element physical pointer.
This patch:
* Ensures that ramrods are sent to the FW with
consecutive echo values.
* Handles out-of-order completions by freeing only first
successive completed entries.
* Updates the chain element physical pointer when copying
a pending element into a free element for sending.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical LEDs are being controlled by the management FW.
This adds the qed functionality required to request management FW to
change the LED configuration, as well as the necessary APIs for this
functionality to later be used by the protocol drivers.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() is a variant of netif_napi_add()
It should be used by drivers that use a napi structure
to exclusively poll TX.
We do not want to add this kind of napi in napi_hash[] in following
patches, adding generic busy polling to all NAPI drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added qlogic qed driver uses the zlib library, but
misses the dependency:
drivers/built-in.o: In function `qed_alloc_stream_mem':
drivers/net/ethernet/qlogic/qed/qed_main.c:707: undefined reference to `zlib_inflate_workspacesize'
drivers/built-in.o: In function `qed_unzip_data':
drivers/net/ethernet/qlogic/qed/qed_main.c:675: undefined reference to `zlib_inflateInit2'
This changes Kconfig to always select zlib when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver saves a copy of slaves' original mac address and then
assigns whatever mac as needed to the slave, depending on mode. In at
least modes 5 and 6 (balance-tlb, balance-alb), it often ends up being the
mac address of another slave. On release from the bond, the original mac
address is supposed to get restored via a dev_set_mac_address() call in
the bonding driver's __bond_release_one() function, which calls the
slave's ndo_set_mac_address function, which for qlcnic, is
qlcnic_set_mac().
Now, this function tries to be somewhat intelligent and exit early if
you're trying to set the mac address to the same thing that is already
set. The problem here is that adapter->mac_addr isn't in sync with
netdev->dev_addr. The qlcnic driver still has the original mac stored in
adapter->mac_addr, while the bonding driver has updated netdev->dev_addr,
so qlcnic thinks we're trying to set the same address it already has.
I think the way to go here, since the function updates both netdev and
adapter's stored mac addresses, is to check if either of them doesn't
match the newly requested mac. Simply checking netdev's value only could
result in a similar mismatch and non-update, so look at both.
CC: Dept-GELinuxNICDev@qlogic.com
CC: netdev@vger.kernel.org
CC: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally return success instead of -ENOMEM here.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
MODE_MF_SI is 9. We should be testing bit 9 instead of AND 0x9.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check if "p_hwfn" is NULL and then dereference it in the error
handling code. I read the code and it isn't NULL so let's remove the
check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only instance of a qlcnic_mbx_ops structure is never modified. Thus
the declaration of the structure and all references to the structure type
can be made const.
In the definition of the qlcnic_mailbox structure, the ops field is no
longer lined up with the other fields. This was left as is, to avoid a lot
of trivial changes on the other lines.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback for adding vxlan port can be called with the same port for
both IPv4 and IPv6. Do not disable the offloading when the same port for
both protocols is added and later one of them removed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all cases, mbx->req.arg and mbx->rsp.arg have just been allocated
using kcalloc(), so these six memsets are redundant.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
