At91_mci is abusing dma_free_coherent(), which may not be called with IRQs
disabled. I saw "mkfs.ext3" on an MMC card objecting voluminously as each
write completed:
WARNING: at arch/arm/mm/consistent.c:368 dma_free_coherent+0x2c/0x224()
[<c002726c>] (dump_stack+0x0/0x14) from [<c00387d4>] (warn_on_slowpath+0x4c/0x68)
[<c0038788>] (warn_on_slowpath+0x0/0x68) from [<c0028768>] (dma_free_coherent+0x2c/0x224)
r6:00008008 r5:ffc06000 r4:00000000
[<c002873c>] (dma_free_coherent+0x0/0x224) from [<c01918ac>] (at91_mci_irq+0x374/0x420)
[<c0191538>] (at91_mci_irq+0x0/0x420) from [<c0065d9c>] (handle_IRQ_event+0x2c/0x6c)
...
This bug has been around for a LONG time. The MM warning is from late
2005, but the driver merged a year later ... so I'm puzzled why nobody
noticed this before now.
The fix involves noting that this buffer shouldn't be DMA-coherent; it's
just used for normal DMA writes. So replace it with standard kmalloc()
buffering and DMA mapping calls.
This is the quickie fix. A better one would not rely on allocating large
bounce buffers. (Note that dma_alloc_coherent could have failed too, but
that case was ignored... kmalloc is a bit more likely to fail though.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus-mmc@drzeus.cx>
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Relax requirements on host controllers and only require that they do not
report a transfer count than is larger than the actual one (i.e. a lower
value is okay). This is how many other parts of the kernel behaves so
upper layers should already be prepared to handle that scenario. This
gives us a performance boost on MMC cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The byte mode support fails to clear the byte mode bit in the command
register, possibly leaving byte mode enabled with the counters programmed
in non-byte mode.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
According to the documentation the AT91SAM9261 MCI shares the block size
limitations of the AT91RM9200 MCI. Also the errata documentation for
AT91RM9200 and AT91SAM9261 state that stream commands are not supported.
This has not been tested on actual hardware.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
AT91SAM926[0/3] PDC must write at least 12 bytes. The code compiles and runs
but the actual condition for this erratum did not trigger in my tests so it's
unclear if it actually works as intended.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In at91_mci_completed_command() function, this patch distinguishes
command error and data error. It reports it in the corresponding
error field.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Reading AT91_MCI_SR again at the end of transfer can corrupt the
error reporting. Some fields in the SR register are read-and-clear.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Enable SDIO interrupt handling.
Signed-off-by: Eric Benard <ebenard@free.fr>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
at91_mci is capable of multiwrite. Enable it before it disappears.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Modify bytes_xfered value after a write.
That will report, as accurately as possible, the amount of
sectors that are effectively written.
This update introduces the check of the busy signal given by
the card.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The at91 mci controller internal state machine seems to often crash. This can
be fixed by resetting the controller after each command for at91rm9200 and by
setting the MCI_BLKR register on at91sam926*.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Implement transfer with size not modulo 4 for at91sam9*. Please note that the
at91rm9200 simply can't handle this.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Now get_ro() callback must return 0/1 values for its logical states, and
negative errno values in case of error. If particular host instance doesn't
support RO/WP switch, it should return -ENOSYS.
This patch changes some hosts in two ways:
1. Now functions should be smart to not return negative values in
"RO asserted" case (particularly gpio_ calls could return negative
values for the outermost GPIOs).
Also, board code usually passes get_ro() callbacks that directly return
gpioreg & bit result, so at91_mci, imxmmc, pxamci and mmc_spi's get_ro()
handlers need take special care when returning platform's values to the
mmc core.
2. In case of host instance didn't implement get_ro() callback, it should
really return -ENOSYS and let the mmc core decide what to do about it
(mmc core thinks the same way as the hosts, so it isn't functional
change).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
MMC_POWER_ON is a noop, no need to set the power pin again.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MMC host
platform drivers, to re-enable auto loading.
Also, add missing owner declarations in driver init.
[dbrownell@users.sourceforge.net: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the AT91 MMC driver to use the generic GPIO calls instead of the
AT91-specific calls; and to request (and release) those GPIO signals.
That required updating the probe() fault cleanup codepaths. Now there
is a single sequence for freeing resources, in reverse order of their
allocation. Also that code uses use dev_*() for messaging, and has less
abuse of KERN_ERR.
Likewise with updating remove() cleanup. This had to free the GPIOs,
and while adding that code I noticed and fixed two other problems: it
was poking at a workqueue owned by the mmc core; and in one (rare)
case would try freeing an IRQ that it didn't allocate.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
A small MMC driver cleanup.
Use the defined AT91_MCI_ERRORS in at91_mci_completed_command() instead
of specifying all the error bits individually.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This kind of transfer is not supported, so don't advertise it and make it
fail early.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The MMC_DATA_MULTI flag never had a proper definition of what it
means, so remove it and let the drivers check the block count in
the request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes a bug in AT91 mmc host driver, that enables the wakeup
from suspend on card detection pin even if the card detect pin is not
available (==0). If not card detection pin is defined, IRQ0 == FIQ gets
enabled and if some activity is present on that pin, the system gets a
FIQ request, that causes a crash.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cleanup with whitespace/tab at the end of lines.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This piece of code enable the system to be wake-up by a card insertion or removal.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fixes hanging using multi block operations (seen during CMD25).
Follows closely the datasheet flowcharts.
This piece of code handles better big file writing. I had to take care
of the notbusy signal during write (at91_mci_handle_cmdrdy function) and
to rearrange the AT91_MCI_ENDRX and AT91_MCI_RXBUFF flag usage.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Typo fix in at91_mci driver : standardized the typo
(at91_mci everywhere)
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix compilation error by removing command decoding from at91_mci.c driver.
Decoding commands in the host driver is the wrong way.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
