Stephen Warren reported the recent commit 78506f2 (add support for
extended FIFO-size of PL011-r1p5) breaks the serial port on the
BCM2835 ARM SoC.
A UART compatible with the ARM PL011-r1p5 should have 32-deep FIFOs.
The BCM2835 UART just looks like an ARM PL011-r1p5, but has 16-deep
FIFOs just like PL011-r1p4 or earlier revisions. As a workaround for
this compatibility issue, this patch overrides the HW UART periphid
register values with the actually compatible UART periphid 0x00241011
(r1p3 or r1p4).
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.
Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear only those interrupts that we have read
as active first time around, because else we have a race and risk clearing an
interrupt that can occur between read and write of the SATAINTSTAT register
and never registering it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This patch addresses kernel bug 56661. BIOS reports an incorrect
backlight value, causing the driver to switch off the backlight
completely during startup. This patch ignores the incorrect value from
BIOS.
References: https://bugzilla.kernel.org/show_bug.cgi?id=56661
Signed-off-by: Ash Willis <ashwillis@programmer.net>
Cc: All <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On HP m4 lapops, BIOS reports minimum backlight on boot and
causes backlight to dim completely. This ignores the initial backlight
values and set to max brightness.
References: https://bugs.launchpad.net/bugs/1184501
Cc: All <stable@vger.kernel.org>
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull parisc fixes from Helge Deller:
"This patcheset includes fixes for:
- the PCI/LBA which brings back the stifb graphics framebuffer
console
- possible memory overflows in parisc kernel init code
- parport support on older GSC machines
- avoids that users by mistake enable PARPORT_PC_SUPERIO on parisc
- MAINTAINERS file list updates for parisc."
* 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: parport0: fix this legacy no-device port driver!
parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
parisc/PCI: Set type for LBA bus_num resource
MAINTAINERS: update parisc architecture file list
parisc: kernel: using strlcpy() instead of strcpy()
parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
parisc: memory overflow, 'name' length is too short for using
Fix the above kernel error from parport_announce_port() on 32bit GSC
machines (e.g. B160L). The parport driver requires now a pointer to the
device struct.
Signed-off-by: Helge Deller <deller@gmx.de>
If enabled, CONFIG_PARPORT_PC_SUPERIO scans on PC-like hardware for
various super-io chips by accessing i/o ports in a range which will
crash any parisc hardware at once.
In addition, parisc has it's own incompatible superio chip
(CONFIG_SUPERIO), so if we disable PARPORT_PC_SUPERIO completely for
parisc we can avoid that people by accident enable the parport_pc
superio option too.
Signed-off-by: Helge Deller <deller@gmx.de>
commit dc7dce280a
Author: Bjorn Helgaas <bhelgaas@google.com>
Date: Fri Oct 28 16:27:27 2011 -0600
parisc/PCI: lba: convert to pci_create_root_bus() for correct root bus
resources
Supply root bus resources to pci_create_root_bus() so they're correct
immediately. This fixes the problem of "early" and "header" quirks seeing
incorrect root bus resources.
added tests for elmmio_space.start while it should use
elmmio_space.flags. This for example led to incorrect resource
assignments and a non-working stifb framebuffer on most parisc machines.
LBA 10:1: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io 0x12000-0x13fff] (bus address [0x2000-0x3fff])
pci_bus 0000:01: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
pci_bus 0000:01: root bus resource [mem 0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
pci_bus 0000:01: root bus resource [??? 0x00000001 flags 0x0]
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The non-PAT resource probing code failed to set the type of the LBA bus_num
resource (30aa80da43 "parisc/PCI: register busn_res for root buses" did
the corresponding thing for the PAT case).
This causes incorrect resource assignments and a non-working stifb
framebuffer on most parisc machines.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Helge Deller <deller@gmx.de>
'boot_args' is an input args, and 'boot_command_line' has a fix length.
So use strlcpy() instead of strcpy() to avoid memory overflow.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Helge Deller <deller@gmx.de>
There's a Makefile line setting cflags for CONFIG_PA7100. But that
Kconfig macro doesn't exist. There is a Kconfig symbol PA7000, which
covers both PA7000 and PA7100 processors. So let's use the corresponding
Kconfig macro.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Helge Deller <deller@gmx.de>
With CONFIG_DISCONTIGMEM=y and multiple physical memory areas,
cat /proc/kpageflags triggers this kernel bug:
kernel BUG at arch/parisc/include/asm/mmzone.h:50!
CPU: 2 PID: 7848 Comm: cat Tainted: G D W 3.10.0-rc3-64bit #44
IAOQ[0]: kpageflags_read0x128/0x238
IAOQ[1]: kpageflags_read0x12c/0x238
RP(r2): proc_reg_read0xbc/0x130
Backtrace:
[<00000000402ca2d4>] proc_reg_read0xbc/0x130
[<0000000040235bcc>] vfs_read0xc4/0x1d0
[<0000000040235f0c>] SyS_read0x94/0xf0
[<0000000040105fc0>] syscall_exit0x0/0x14
kpageflags_read() walks through the whole memory, even if some memory
areas are physically not available. So, we should better not BUG on an
unavailable pfn in pfn_to_nid() but just return the expected value -1 or
0.
Signed-off-by: Helge Deller <deller@gmx.de>
'path.bc[i]' can be asigned by PCI_SLOT() which can '> 10', so sizeof(6
* "%u:" + "%u" + '\0') may be 21.
Since 'name' length is 20, it may be memory overflow.
And 'path.bc[i]' is 'unsigned char' for printing, we can be sure the
max length of 'name' must be less than 28.
So simplify thinking, we can use 28 instead of 20 directly, and do not
think of whether 'patchc.bc[i]' can '> 100'.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few more fixes for powerpc 3.10. It's a bit more than I
would have liked this late in the game but I suppose that's what
happens with a brand new chip generation coming out.
A few regression fixes, some last minute fixes for new P8 features
such as transactional memory,...
There's also one powerpc KVM patch that I requested that adds two
missing functions to our in-kernel interrupt controller support which
is itself a new 3.10 feature. These are defined by the base
hypervisor specification. We didn't implement them originally because
Linux doesn't use them but they are simple and I'm not comfortable
having a half-implemented interface in 3.10 and having to deal with
versionning etc... later when something starts needing those calls.
They cannot be emulated in qemu when using in-kernel interrupt
controller (not enough shared state).
Just added a last minute patch to fix a typo introducing a breakage in
our cputable for Power7+ processors, sorry about that, but the
regression it fixes just hurt me :-)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/cputable: Fix typo on P7+ cputable entry
powerpc/perf: Add missing SIER support
powerpc/perf: Revert to original NO_SIPR logic
powerpc/pci: Remove the unused variables in pci_process_bridge_OF_ranges
powerpc/pci: Remove the stale comments of pci_process_bridge_OF_ranges
powerpc/pseries: Always enable CONFIG_HOTPLUG_CPU on PSERIES SMP
powerpc/kvm/book3s: Add support for H_IPOLL and H_XIRR_X in XICS emulation
powerpc/32bit:Store temporary result in r0 instead of r8
powerpc/mm: Always invalidate tlb on hpte invalidate and update
powerpc/pseries: Improve stream generation comments in copypage/user
powerpc/pseries: Kill all prefetch streams on context switch
powerpc/cputable: Fix oprofile_cpu_type on power8
powerpc/mpic: Fix irq distribution problem when MPIC_SINGLE_DEST_CPU
powerpc/tm: Fix userspace stack corruption on signal delivery for active transactions
powerpc/tm: Move TM abort cause codes to uapi
powerpc/tm: Abort on emulation and alignment faults
powerpc/tm: Update cause codes documentation
powerpc/tm: Make room for hypervisor in abort cause codes
Pull scsi target fixes from Nicholas Bellinger:
"The highlights include:
- Re-instate sess->wait_list in target_wait_for_sess_cmds() for
active I/O shutdown handling in fabrics using se_cmd->cmd_kref
- Make ib_srpt call target_sess_cmd_list_set_waiting() during session
shutdown
- Fix FILEIO off-by-one READ_CAPACITY bug for !S_ISBLK export
- Fix iscsi-target login error heap buffer overflow (Kees)
- Fix iscsi-target active I/O shutdown handling regression in
v3.10-rc1
A big thanks to Kees Cook for fixing a long standing login error
buffer overflow bug.
All patches are CC'ed to stable with the exception of the v3.10-rc1
specific regression + other minor target cleanup."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix iscsit_free_cmd() se_cmd->cmd_kref shutdown handling
target: Propigate up ->cmd_kref put return via transport_generic_free_cmd
iscsi-target: fix heap buffer overflow on error
target/file: Fix off-by-one READ_CAPACITY bug for !S_ISBLK export
ib_srpt: Call target_sess_cmd_list_set_waiting during shutdown_session
target: Re-instate sess_wait_list for target_wait_for_sess_cmds
target: Remove unused wait_for_tasks bit in target_wait_for_sess_cmds
discrete clock expander chip. Most fixes are corrections to lousy clock
data of one form or another.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=OuqZ
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clock subsystem fixes from Mike Turquette:
"A mix of small fixes affecting mostly ARM platforms as well as a
discrete clock expander chip. Most fixes are corrections to lousy
clock data of one form or another."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: mxs: Include clk mxs header file
clk: vt8500: Fix unbalanced spinlock in vt8500_dclk_set_rate()
clk: si5351: Set initial clkout rate when defined in platform data.
clk: si5351: Fix clkout rate computation.
clk: samsung: Add CLK_IGNORE_UNUSED flag for the sysreg clocks
clk: ux500: clk-sysctrl: handle clocks with no parents
clk: ux500: Provide device enumeration number suffix for SMSC911x
Pull assorted fixes from Al Viro:
"There'll be more - I'm trying to dig out from under the pile of mail
(a couple of weeks of something flu-like ;-/) and there's several more
things waiting for review; this is just the obvious stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
zoran: racy refcount handling in vm_ops ->open()/->close()
befs_readdir(): do not increment ->f_pos if filldir tells us to stop
hpfs: deadlock and race in directory lseek()
qnx6: qnx6_readdir() has a braino in pos calculation
fix buffer leak after "scsi: saner replacements for ->proc_info()"
vfs: Fix invalid ida_remove() call
- Fix a regression that broke NFS mounting using klibc and busybox
- Stable fix to check access modes correctly on NFSv4 delegated open()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=HTIq
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull two NFS client fixes from Trond Myklebust:
- Fix a regression that broke NFS mounting using klibc and busybox
- Stable fix to check access modes correctly on NFSv4 delegated open()
* tag 'nfs-for-3.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix security flavor negotiation with legacy binary mounts
NFSv4: Fix a thinko in nfs4_try_open_cached
Since the recent addition of 8021AD, we need to set the new field vlan_proto in
sk_buff. Otherwise, it will trigger BUG() call in vlan_proto_idx().
This patch fixes the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the port list dump does not fit into one skb currently the
dump would start over again. Fix this by continue from the last dumped
port.
Introduced by commit d90f889e9c (team: handle sending port list in the
same way option list is sent)
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SELinux labeled IPsec code was improperly handling its reference
counting, dropping a reference on a delete operation instead of on a
free/release operation.
Reported-by: Ondrej Moris <omoris@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases after deleting a policy from the SPD the policy would
remain in the dst/flow/route cache for an extended period of time
which caused problems for SELinux as its dynamic network access
controls key off of the number of XFRM policy and state entries.
This patch corrects this problem by forcing a XFRM garbage collection
whenever a policy is sucessfully removed.
Reported-by: Ondrej Moris <omoris@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp6 over GRE tunnel does not work after to GRE tso changes. GRE
tso handler passes inner packet but keeps track of outer header
start in SKB_GSO_CB(skb)->mac_offset. udp6 fragment need to
take care of outer header, which start at the mac_offset, while
adding fragment header.
This bug is introduced by commit 68c3316311 (GRE: Add TCP
segmentation offload for GRE).
Reported-by: Dmitry Kravkov <dkravkov@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Tested-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_mc_sync_multiple function is currently calling
__hw_addr_sync, and not __hw_addr_sync_multiple. This will result in
addresses only being synced to the first device from the set.
Corrected by calling the _multiple variant.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, __hw_addr_sync_one is called in a loop by
__hw_addr_sync_multiple to sync each of a "from" device's hw addresses
to a "to" device. __hw_addr_sync_one calls __hw_addr_add_ex to attempt
to add each address. __hw_addr_add_ex is called with global=false, and
sync=true.
__hw_addr_add_ex checks to see if the new address matches an
address already on the list. If so, it tests global and sync. In this
case, sync=true, and it then checks if the address is already synced,
and if so, returns 0.
This 0 return causes __hw_addr_sync_one to increment the sync_cnt
and refcount for the "from" list's address entry, even though the address
is already synced and has a reference and sync_cnt. This will cause
the sync_cnt and refcount to increment without bound every time an
addresses is added to the "from" device and synced to the "to" device.
The fix here has two parts:
First, when __hw_addr_add_ex finds the address already exists
and is synced, return -EEXIST instead of 0.
Second, __hw_addr_sync_one checks the error return for -EEXIST,
and if so, it (a) does not add a refcount/sync_cnt, and (b) returns 0
itself so that __hw_addr_sync_multiple will not return an error.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an address is added to a subordinate interface (the "to"
list), the address entry in the "from" list is not marked "synced" as
the entry added to the "to" list is.
When performing the unsync operation (e.g., dev_mc_unsync),
__hw_addr_unsync_one calls __hw_addr_del_entry with the "synced"
parameter set to true for the case when the address reference is being
released from the "from" list. This causes a test inside to fail,
with the result being that the reference count on the "from" address
is not properly decremeted and the address on the "from" list will
never be freed.
Correct this by having __hw_addr_unsync_one call the
__hw_addr_del_entry function with the "sync" flag set to false for the
"remove from the from list" case.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sync_cnt field is not being initialized, which can result
in arbitrary values in the field. Fixed by initializing it to zero.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a typo in setting COMMON_USER2_POWER7 bits to .cpu_user_features2
cpu specs table.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This stat is not relevant in IPv6, there is no checksum in IPv6 header.
Just leave a comment to explain the hole.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8f61aa3 "Add support for SIER" missed updates to siar_valid()
and perf_get_data_addr().
In both cases we need to check the SIER instead of mmcra.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a revert and then some of commit 860aad7 "Add regs_no_sipr()".
This workaround was only needed on early chip versions.
As before NO_SIPR becomes a static flag of the PMU struct.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The codes which ever used these two variables have gone. Throw away
them too.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These comments already don't apply to the current code. So just remove
them.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adam Lackorzynski reported the following build failure on
!CONFIG_HOTPLUG_CPU configuration:
CC arch/powerpc/kernel/rtas.o
arch/powerpc/kernel/rtas.c: In function ‘rtas_cpu_state_change_mask’:
arch/powerpc/kernel/rtas.c:843:4: error: implicit declaration of function ‘cpu_down’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[1]: *** [arch/powerpc/kernel/rtas.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
The build fails because cpu_down() is defined only under CONFIG_HOTPLUG_CPU.
Looking further, the mobility code in pseries is one of the call-sites which
uses rtas_ibm_suspend_me(), which in turn calls rtas_cpu_state_change_mask().
And the mobility code is unconditionally compiled-in (it does not fall under
any Kconfig option). And commit 120496ac (powerpc: Bring all threads online
prior to migration/hibernation) which introduced this build regression is
critical for the proper functioning of the migration code. So it appears
that the only solution to this problem is to enable CONFIG_HOTPLUG_CPU if
SMP is enabled on PPC_PSERIES platforms. So make that change in the Kconfig.
Reported-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the remaining two hypercalls defined by PAPR for manipulating
the XICS interrupt controller, H_IPOLL and H_XIRR_X. H_IPOLL returns
information about the priority and pending interrupts for a virtual
cpu, without changing any state. H_XIRR_X is like H_XIRR in that it
reads and acknowledges the highest-priority pending interrupt, but it
also returns the timestamp (timebase register value) from when the
interrupt was first received by the hypervisor. Currently we just
return the current time, since we don't do any software queueing of
virtual interrupts inside the XICS emulation code.
These hcalls are not currently used by Linux guests, but may be in
future.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit a9c4e541ea
"powerpc/kprobe: Complete kprobe and migrate exception frame"
introduced a regression:
While returning from exception handling in case of PREEMPT enabled,
_TIF_NEED_RESCHED bit is checked in TI_FLAGS (thread_info flag) of current
task. Only if this bit is set, it should continue with the process of
calling preempt_schedule_irq() to schedule highest priority task if
available.
Current code assumes that r8 contains TI_FLAGS and check this for
_TIF_NEED_RESCHED, but as r8 is modified in the code which executes before
this check, r8 no longer contains the expected TI_FLAGS information.
As a result check for comparison with _TIF_NEED_RESCHED was failing even if
NEED_RESCHED bit is set in the current thread_info flag. Due to this,
preempt_schedule_irq() and in turn scheduler was not getting called even if
highest priority task is ready for execution.
So, store temporary results in r0 instead of r8 to prevent r8 from getting
modified as subsequent code is dependent on its value.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
CC: <stable@vger.kernel.org> [v3.7+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a hash bucket gets full, we "evict" a more/less random entry from it.
When we do that we don't invalidate the TLB (hpte_remove) because we assume
the old translation is still technically "valid". This implies that when
we are invalidating or updating pte, even if HPTE entry is not valid
we should do a tlb invalidate.
This was a regression introduced by b1022fbd29
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No code changes, just documenting what's happening a little better.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On context switch, we should have no prefetch streams leak from one
userspace process to another. This frees up prefetch resources for the
next process.
Based on patch from Milton Miller.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Maynard informed me that neither the oprofile kernel module nor oprofile
userspace has been updated to support that "legacy" oprofile module
interface for power8, which is indicated by "ppc64/power8." This results
in no samples. The solution is to default to the "timer" type, instead.
The raw entry also should be updated, as "ppc64/ibm-compat-v1" indicates
to oprofile userspace to use "compatibility events" which are obsolete
in ISA 2.07.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For the mpic with a flag MPIC_SINGLE_DEST_CPU, only one bit should be
set in interrupt destination registers.
The code is applicable to 64-bit platforms as well as 32-bit.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When in an active transaction that takes a signal, we need to be careful with
the stack. It's possible that the stack has moved back up after the tbegin.
The obvious case here is when the tbegin is called inside a function that
returns before a tend. In this case, the stack is part of the checkpointed
transactional memory state. If we write over this non transactionally or in
suspend, we are in trouble because if we get a tm abort, the program counter
and stack pointer will be back at the tbegin but our in memory stack won't be
valid anymore.
To avoid this, when taking a signal in an active transaction, we need to use
the stack pointer from the checkpointed state, rather than the speculated
state. This ensures that the signal context (written tm suspended) will be
written below the stack required for the rollback. The transaction is aborted
becuase of the treclaim, so any memory written between the tbegin and the
signal will be rolled back anyway.
For signals taken in non-TM or suspended mode, we use the
normal/non-checkpointed stack pointer.
Tested with 64 and 32 bit signals
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These cause codes are usable by userspace, so let's export to uapi.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we are emulating an instruction inside an active user transaction that
touches memory, the kernel can't emulate it as it operates in transactional
suspend context. We need to abort these transactions and send them back to
userspace for the hardware to rollback.
We can service these if the user transaction is in suspend mode, since the
kernel will operate in the same suspend context.
This adds a check to all alignment faults and to specific instruction
emulations (only string instructions for now). If the user process is in an
active (non-suspended) transaction, we abort the transaction go back to
userspace allowing the HW to roll back the transaction and tell the user of the
failure. This also adds new tm abort cause codes to report the reason of the
persistent error to the user.
Crappy test case here http://neuling.org/devel/junkcode/aligntm.c
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
