cAVS modules do not require Type and Length header within the
set_module_params IPC. This is also true for Vendor modules. The
userspace (like tinymix) always appends this header to TLV controls
which are used for set_module_params. Simply assume this header is
always present in the payload and omit it from the IPC.
Signed-off-by: Kamil Lulko <kamilx.lulko@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before actual deletion, pipeline should enter RESET state. Currently,
pipe skips this checkpoint and goes straight to the finish line.
This is not the expected path by the FW, so correct it.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since there are multiple IPCs being sent in a short span of time, there
is a possibility of more than one message being on the Rx list after
receiving response from firmware. In such cases, when the first
notification of interrupt from firmware is received, driver retrieves
the message from the Rx list but does not delete it from the list till
the next lock. In the meantime, when another interrupt is received from
the firmware, driver is reading the previous message again since the
previous message has not been removed from the list.
Signed-off-by: Gustaw Lewandowski <gustaw.lewandowski@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Host clears DONE bit to signal IPC target it has completed the
operation. Once this is done, IPC target i.e. DSP may proceed with the
next reply, filling registers with new portion of data.
Because of this, host should always read all registers prior to clearing
DONE and BUSY bits to ensure no desynchronization happens the time in
between clearing bits and reading message data (here, extension).
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When driver is probed, we iterate over NHLT and check if clk entries are
present. For each such entry we call register_skl_clk and keep the
result in data->clk[].
Currently data->clk is sparsely indexed using NHLT table iterator, while
when freeing we use number of registered entries. Let's just use
data->avail_clk_cnt as index, so it can be reset back in
unregister_src_clk.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we remove component we need to reverse things which were done on
init, this consists of topology cleanup, lists cleanup and releasing
firmware.
Currently cleanup handlers are put in wrong places or otherwise missing.
So add proper component cleanup function and perform cleanups in it.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently debugfs has no cleanup function. Add skl_debufs_exit function
so we can clean after ourselves properly.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we unload and reload machine driver, we shouldn't return that we
failed to initialize. This allows to reload machine driver, without
having to unload whole stack.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If skl_probe_work() was not run driver ends up dereferencing NULL
pointer when operating on lists in skl_platform_unregister().
To fix this initialize lists in skl_create(). Also run
cancel_work_sync() before all cleanup functions, so we don't end up
unnecessarily running probe work.
Easily reproducible with:
while true; do modprobe snd_soc_skl; rmmod snd_soc_skl; done
(with the assumption that relevant drivers are added to blacklist on
system boot)
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For BXT platforms, the recommended sequence to program the SDxFMT is to
first couple the stream, write the format and decouple again.
For all other platforms said sequence remains unchanged.
To prevent code duplication, IS_BXT (and consequently IS_CFL) macro is
relocated to hda_codec.h file so it can be accessed by SKL driver.
Signed-off-by: Paweł Harłoziński <pawel.harlozinski@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch the driver to use modern UUID API, i.e. guid_t type and
accompanying functions, such as guid_equal().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 13 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081205.608593891@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HW recommends to set DUM bit on device power up, so that DPIB write
request occurs every frame regardless of whether DPIB has changed or
not. This addresses incorrect position reporting for capture streams.
Signed-off-by: Leoni Prodduvaka <leoni.prodduvaka@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
uuid_params->num_modules * sizeof(struct skl_mod_inst_map) + sizeof(uuid_params->num_modules)
with:
struct_size(params, u.map, uuid_params->num_modules)
and so on...
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PCI IDs for Intel CometLake platforms, which from a software
point of view are extremely similar to Cannonlake platforms.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Recently, for Intel platforms the "ignore_module_refcount" field
was introduced for the component driver. In order to avoid a
deadlock preventing the PCI modules from being removed
even when the card was idle, the refcounts were not incremented
for the device driver module during component probe.
However, this change introduced a nasty side effect:
the device driver module can be unloaded while a pcm stream is open.
This patch proposes to change the field to be renamed as
"module_get_upon_open". When this field is set, the module
refcount should be incremented on pcm open amd decremented
upon pcm close. This will enable modules to be removed
when no PCM playback/capture happens and prevent removal
when the component is actually in use.
Also, align with the skylake component driver with the new name.
Fixes: b450b878('ASoC: core: don't increase component module refcount
unconditionally'
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology is not unloaded in the core during unregister_component()
anymore. So, add the remove() callback that will unload the
topology.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable S24_LE format, sample_type in topology fw has to be set to 1.
But sample_type defined in topology firmware configuration is not
getting reflected in the dsp param. This patch sets sample_type in base
config so that the sample type defined in the topology firmware is reflected
in the dsp params. This issues was uncovered while debugging the S24_LE format
which require the MSB byte in 32 bit word to be skipped. Setting sample_type
in topology firmware to 1 helps to skip MSB byte word.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If playback and capture are enabled concurrently, when the capture stops
the output becomes inaudile. The playback application will become stuck
and underrun after a timeout.
This is caused by mistaken use of the stream_id, which should only be
set for playback and not for capture
Tested on Apollolake and Kabylake with SST driver.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Another batch of changes for ASoC, no big core changes - it's mainly
small fixes and improvements for individual drivers.
- A big refresh and cleanup of the Samsung drivers, fixing a number of
issues which allow the driver to be used with a wider range of
userspaces.
- Fixes for the Intel drivers to make them more standard so less likely
to get bitten by core issues.
- New driver for Cirrus Logic CS35L26.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx3z7ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H5QB/9jwKEwOdk6ynoFUpQwXPPkQl7CGkIh
P8J3OMTt+U4FNOrVG2S7xgUl69ZoaLm9rS/PHVrMV5krSLqY//2CTvF068qDBBlj
haBxgeRbe4pwLZPfFUnWvn6v1rdvNCXzDG/be9jGPJjDcm6wK44VJQWkPbqTsh6O
ZORqvKn48D89W0DegG1B+4jvbietPkhA0+nHQXwsWZ+sfMcEV/AWWsE5FIQ7ucCC
bundBBncUFKMMp9whuhj2W9FO62LUd8OAM7ejis3hfKk9MsQWUy6vrcN1XgRCq47
4I0doB5o+WhsOGMTZMcuhFISCVaCDqbNqGuVbeK0sdonjc1xz0682jLo
=9rq8
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More changes for v5.1
Another batch of changes for ASoC, no big core changes - it's mainly
small fixes and improvements for individual drivers.
- A big refresh and cleanup of the Samsung drivers, fixing a number of
issues which allow the driver to be used with a wider range of
userspaces.
- Fixes for the Intel drivers to make them more standard so less likely
to get bitten by core issues.
- New driver for Cirrus Logic CS35L26.
There is no risk of the module being removed while the platform
components are in use. This solves the problem of the snd_soc_skl
module not being removable with rmmod
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lots and lots of new drivers so far, a highlight being the MediaTek
BTCVSD which is a driver for a Bluetooth radio chip - the first such
driver we've had upstream. Hopefully we will soon also see a baseband
with an upstream driver!
- Support for only powering up channels that are actively being used.
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers.
- Lots of fixes for probing on Intel systems, trying to rationalize
things to look more standard from a framework point of view.
- New drivers for Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341,
Google ChromeOS embedded controllers, Ingenic JZ4725B, MediaTek
BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328, Spreadtrum
DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM formatters.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlxde0wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JWRB/9aQsLR22dNvKosiitTO/nnnPw/sUiG
cFZsI4G1mFpjXyC2azaY1MQOIjRZY3WDsRjcHtAJUkdJnz8fdyj74mIRoHrQI/yv
qdc7EtV5J0k0DemDQH2z5J7WjrkLg4aQCMT2XIvwrXL44jBv/iVKUE8l08D2AZ6t
hQiVIF/9iBnaJwqfUSKzJaufdd88Onh1dBljLGwZnRDtG9mndpxoi+S9pR6gwSMG
JzbgO4kUXdN95wKPxDsHFZimiSaX4bBo2cr79cisPrvcIKTyMAdtkAoNAcyuRezx
qiN2l4zz6Wxi8TygkBZfmWGKz2/2fMDWLvYwfEnA9PhddlSUZt/P1IPl
=tkEF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v5.1
Lots and lots of new drivers so far, a highlight being the MediaTek
BTCVSD which is a driver for a Bluetooth radio chip - the first such
driver we've had upstream. Hopefully we will soon also see a baseband
with an upstream driver!
- Support for only powering up channels that are actively being used.
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers.
- Lots of fixes for probing on Intel systems, trying to rationalize
things to look more standard from a framework point of view.
- New drivers for Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341,
Google ChromeOS embedded controllers, Ingenic JZ4725B, MediaTek
BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328, Spreadtrum
DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM formatters.
snd_pcm_lib_preallocate_pages() and co always succeed, so the error
check is simply redundant. Drop it.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the refactoring of HD-audio display power management, the
display power status is managed per domain. Meanwhile the ASoC
hdac_hdmi driver still keeps and relies (incorrectly) on the
refcounting together with ASoC skl driver, and this leads to the
display state always on.
This patch is an attempt to address the regression by simplifying the
PM code of ASoC skl and hdac_hdmi drivers. Basically, since the
refactoring, we don't have to manage the display power at HD-audio
controller suspend / resume but only at HD-audio HDMI codec suspend /
resume. So the patch drops the superfluous snd_hdac_display_power()
calls in skl driver.
Meanwhile, in hdac_hdmi side, we rewrite the PM call just to re-use
the runtime PM callbacks like other drivers do. Now the logic is
simple: turn off at suspend and turn on at resume.
The patch also fixes the possibly missing display-power off at skl
driver removal as well as some error paths at probe.
Fixes: 029d92c289 ("ALSA: hda: Refactor display power management")
Reported-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Detected with Coccinelle
skl-messages.c:419:5-32: WARNING: Comparison to bool
skl-pcm.c:1426:6-33: WARNING: Comparison to bool
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Detected with Coccinelle
sound/soc/intel/skylake/skl-topology.c:3106:16-20: WARNING: casting
value returned by memory allocation function to (char *) is useless.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For HDaudio and Skylake drivers, add module parameter "pci_binding"
When pci_binding == 0 (AUTO), the PCI class/subclass info is used to
select drivers based on the presence of the DSP.
pci_binding == 1 (LEGACY) forces the use of the HDAudio legacy driver,
even if the DSP is present.
pci_binding == 2 (ASOC) forces the use of the ASOC driver. The
information on the DSP presence is bypassed.
The value for the module parameter needs to be identical for both
drivers. This parameter is intended as a back-up solution if the
automatic detection fails or when the DSP usage fails. Such cases
should be reported on the alsa-devel mailing list for analysis.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not much work on the core this time around but we've seen quite a bit of
driver work, including on the generic DT drivers. There's also a large
part of the diff from a merge of the DaVinci and OMAP directories, along
with some active development there:
- Preparatory work from Morimoto-san for merging the audio-graph and
audio-graph-scu cards.
- A merge of the TI OMAP and DaVinci directories, the OMAP product line
has been merged into the DaVinci product line so there is now a lot
of IP sharing which meant that the split directories just got in the
way. This has pulled in a few architecture changes as well.
- A big cleanup of the Maxim MAX9867 driver from Ladislav Michl.
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx I2S
controllers.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwY7KsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MFqB/4m9nlfUeXTpiSD1FgVIlMmdPNUg4V2
6Ybztaw4kRc5LuQN8PXQmaFLx020yAnLvI7Zzj7l3K8r6a9lfyFs+pKL0wtBnNK2
9QEFmOVQ3QFpt31Yb2IQeO4dfNbiyKeczjLau4mXWTl0j5dc/UH+HasE1dRZOxsC
rqJ8IsdibIVxVtQ7ZmcnU+y6XK0inBHAAh6ksMehsufShGrfrLs/nRBaXRZcRqJg
ciSFY5uYRYkDxTgogTpNRfVy4nr17N10+0sgrQ3RtaaqgG3gBXsHca1meyxKYW3Q
TssOJGIl3+uGiAMNyZqzxe5pAwwuGhZ3hAAAODtfYJQtAuAOW3/45Wqh
=phWF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.21
Not much work on the core this time around but we've seen quite a bit of
driver work, including on the generic DT drivers. There's also a large
part of the diff from a merge of the DaVinci and OMAP directories, along
with some active development there:
- Preparatory work from Morimoto-san for merging the audio-graph and
audio-graph-scu cards.
- A merge of the TI OMAP and DaVinci directories, the OMAP product line
has been merged into the DaVinci product line so there is now a lot
of IP sharing which meant that the split directories just got in the
way. This has pulled in a few architecture changes as well.
- A big cleanup of the Maxim MAX9867 driver from Ladislav Michl.
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx I2S
controllers.
The current SKYLAKE kconfig is a all-you-can-eat selection that will
support all known plaforms. This is however not necessarily a good
thing: most platforms for SKL and KBL don't support the DSP, but a
number of CNL/WHL ones do. Selecting this driver in all cases isn't
really smart and will require users to muck with blacklists.
Partition the configs to allow distributions to select on which
platform this driver is used. Keep the existing SND_SOC_INTEL_SKYLAKE
config to select everything for backwards compatibility. This patch does
not provide new functionality, only finer-grained choices in supported
platforms.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add error logs to make probe debug easier.
Also remove hard-coded dependency on NHLT. NHLT literally stands for
NonHdaudioLinkTable and is only required for SSP/DMIC interfaces.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
bus->ppcap is now tested upfront, there is no need to re-check if the
hardware is exposed as needed. Remove tests and remove indentation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check immediately if required HDaudio capabilities can't be found (no
PPCAP or no streams exposed in GCAP), and move all DMA inits after the
error tests.
PPCAP and GCAP are not reliable indicators of DSP presence, but if
they don't exist then the driver will not work.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing PPCAP and GCAP fields cannot be used reliably to
determine if the DSP is enabled by the BIOS. Instead rely on the
class/subclass information to find out if this driver can run or
not. The values in the code don't seem to be documented in publicly
available documents but are part of recommendations made to BIOS
writers and have been verified to be accurate on a number of
platforms.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's with CNP, supposed to be equivalent with CNL entry.
Keep the existing declaration style for now, at a later point we may
transition and use PCI_DEVICE_DATA().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the recent refactoring, snd_hdac_display_power() doesn't return
any error, hence it can be defined to return void.
This makes many error checks redundant and allows us to reduce them
gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current HD-audio code manages the DRM audio power via too complex
redirections, and this seems even still unbalanced in a corner case as
Intel DRM CI has been intermittently reporting. This patch is a big
surgery for addressing the complexity and the possible unbalance.
Basically the patch changes the display PM in the following ways:
- Both HD-audio controller and codec drivers call a single helper,
snd_hdac_display_power(). (Formerly, the display power control from
a codec was done indirectly via link_power bus ops.)
- snd_hdac_display_power() receives the codec address index. For
turning on/off from the controller, pass HDA_CODEC_IDX_CONTROLLER.
- snd_hdac_display_power() doesn't manage refcounts any longer, but
keeps the power status in bitmap. If any of controller or codecs is
turned on, the function updates the DRM power state via get_power()
or put_power().
Also this refactor allows us more cleanup:
- The link_power bus ops is dropped, so there is no longer indirect
management, as mentioned in the above.
- hdac_device link_power_control flag is moved to hda_codec
display_power_control flag, as it's only for HDA legacy.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106525
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If mclk/sclk is already running, FW responds with IPC reply MCLK/SCLK
already running. Add these to the IPC reply lookup table.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add more meaning to the IPC replies for easy debugging. Replace the switch
case with a lookup table to lookup for the IPC replies and print in human
readable form.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we have different mechanisms for passing data to
machine drivers. Use the solution used by Atom/SST and SOF instead of
using drv_data as done by Skylake.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The changes for HDaudio overlooked the fact that the machine drivers
used for Chromebooks rely on the dmic number information passed as
pdata.
Add dmic_num field to standard interface and use standard interface
instead of SKL-specific one.
Also clean-up pdata definition to remove fields that are no longer
used.
Fixes: 842bb5135f ('ASoC: Intel: use standard interface for Hdaudio machine driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Skylake driver currently has a set of problems supporting
load/unload modules. We need to make the HDaudio codec support
optional to help narrow down the issues.
Support for HDaudio codecs also leads to a Kconfig issue. We want the
hdac_hda codec to be compilable independently of Skylake (e.g. with
ALL_CODECS) but when Skylake is selected as built-in the hdac_hda
codec needs to use the same option due a a code dependency
Solve both problems by adding a user-selectable boolean Kconfig,
select HDAC_HDA as needed and make the HDaudio codec support in the
Skylake driver optional. Tests on a Chell Chromebook device without
HDaudio show no regression for speaker and HDMI playback.
This is submitted as an RFC to allow for comments and more validation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
