then a bunch of driver updates and a handful of new drivers. In terms of
diffstat the Qualcomm and Amlogic drivers are high up there because of all the
clk data introcued by new drivers. The Nvidia Tegra driver had a lot of work
done this cycle too to support suspend/resume and memory controllers. And the
OMAP clk driver got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data, mark things
static, correct incorrect data in drivers, etc. All the little things that
improve drivers and maintain code health. I will point out that there's a patch
in here for the GPIO clk driver, that almost nobody uses, which changes
behavior and causes clk_set_rate() to try to change the GPIO gate clk's parent.
Other than that things are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8 SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system suspend/resume cycle
on exynos542x SoCs
-----BEGIN PGP SIGNATURE-----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=qJNg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This merge window we have one small clk provider API in the core
framework and then a bunch of driver updates and a handful of new
drivers. In terms of diffstat the Qualcomm and Amlogic drivers are
high up there because of all the clk data introcued by new drivers.
The Nvidia Tegra driver had a lot of work done this cycle too to
support suspend/resume and memory controllers. And the OMAP clk driver
got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data,
mark things static, correct incorrect data in drivers, etc. All the
little things that improve drivers and maintain code health. I will
point out that there's a patch in here for the GPIO clk driver, that
almost nobody uses, which changes behavior and causes clk_set_rate()
to try to change the GPIO gate clk's parent. Other than that things
are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe
suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8
SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system
suspend/resume cycle on exynos542x SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (160 commits)
clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
clk: ingenic: Allow drivers to be built with COMPILE_TEST
MAINTAINERS: Update section for Ux500 clock drivers
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
clk: tegra: Use match_string() helper to simplify the code
clk: pxa: fix one of the pxa RTC clocks
clk: sprd: Use IS_ERR() to validate the return value of syscon_regmap_lookup_by_phandle()
clk: armada-xp: remove unused code
clk: tegra: Fix build error without CONFIG_PM_SLEEP
clk: tegra: Add missing stubs for the case of !CONFIG_PM_SLEEP
clk: tegra: Optimize PLLX restore on Tegra20/30
clk: tegra: Add suspend and resume support on Tegra210
...
It is not correct that sys3_pll_out use sys2_pll1_ref_sel as parent.
According to the current imx_clk_sccg_pll design, it uses both
bypass1/2, however set bypass2 as 1 is not correct, because it will
make sys[x]_pll_out use wrong parent and might access wrong registers.
So correct bypass2 to 0 and fix sys3_pll_out_sels.
Fixes: e9dda4af68 ("clk: imx: Refactor entire sccg pll clk")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mipi pll clock comes from the MIPI PHY PLL output, so
it should not be a fixed clock.
MIPI PHY PLL is in the MIPI DSI space, and it is used as
the bit clock for transferring the pixel data out and its
output clock is configured according to the display mode.
So it should be used only for MIPI DSI and not be exported
out for other usages.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
During cpu frequency switching the main "CLK_ARM" is reparented to an
intermediate "step" clock. On imx8mm and imx8mn the 24M oscillator is
used for this purpose but it is extremely slow, increasing wakeup
latencies to the point that i2c transactions can timeout and system
becomes unresponsive.
Fix by switching the "step" clk to SYS_PLL1_800M, matching the behavior
of imx8m cpufreq drivers in imx vendor tree.
This bug was not immediately apparent because upstream arm64 defconfig
uses the "performance" governor by default so no cpufreq transitions
happen.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/f5d2b9c53f1ed5ccb1dd3c6624f56759d92e1689.1571771777.git.leonard.crestez@nxp.com
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
imx_obtain_fixed_clk_hw could be used to simplify code to replace
__clk_get_hw(of_clk_get_by_name(node, "name"))
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_obtain_fixed_clk_hw could be used to simplify code to replace
__clk_get_hw(of_clk_get_by_name(node, "name"))
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_obtain_fixed_clk_hw could be used to simplify code to replace
__clk_get_hw(of_clk_get_by_name(node, "name"))
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_obtain_fixed_clk_hw could be used to simplify code to replace
__clk_get_hw(of_clk_get_by_name(node, "name"))
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In the latest reference manual Rev.0,06/2019, the DDR clock mux
is extended to 2 bits, and the clock options are also changed,
correct them accordingly.
Fixes: b1260067ac ("clk: imx: add imx7ulp clk driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According Architecture definition guide, SYS1_PLL is fixed at
800MHz, SYS2_PLL is fixed at 1000MHz, so let's use imx_clk_fixed
to register the clocks and drop code that could change the rate.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According Architecture definition guide, SYS_PLL1 is fixed at
800MHz, SYS_PLL2 is fixed at 1000MHz, so let's use imx_clk_fixed
to register the clocks and drop code that could change the rate.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According Architecture definition guide, SYS_PLL1 is fixed at
800MHz, SYS_PLL2 is fixed at 1000MHz, so let's use imx_clk_fixed
to register the clocks and drop code that could change the rate.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx8mn there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate. Only one of these gates (the one "dividing" by
one) is currently defined and it's incorrectly set as the parent of all
the fixed-factor dividers.
Add the other 8 gates to the clock tree between sys_pll1/2_bypass and
the fixed dividers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx8mm there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate. Only one of these gates (the one "dividing" by
one) is currently defined and it's incorrectly set as the parent of all
the fixed-factor dividers.
Add the other 8 gates to the clock tree between sys_pll1/2_bypass and
the fixed dividers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx8mq there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate but these gates are not currently defined in
the clock tree.
Add them between sys1/2_pll_out and the fixed dividers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix sparse warnings:
drivers/clk/imx/clk-pll14xx.c:44:37:
warning: symbol 'imx_pll1416x_tbl' was not declared. Should it be static?
drivers/clk/imx/clk-pll14xx.c:57:37:
warning: symbol 'imx_pll1443x_tbl' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This clock is needed by DCSS when high resolutions are used.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
CC: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use common 1413X/1416X PLL clock structure to save a lot
of duplicated code on i.MX8MN clock driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Many i.MX8M SoCs use same 1443X/1416X PLL, such as i.MX8MM,
i.MX8MN and later i.MX8M SoCs, moving these PLL definitions
to pll14xx driver can save a lot of duplicated code on each
platform.
Meanwhile, no need to define PLL clock structure for every
module which uses same type of PLL, e.g., audio/video/dram use
1443X PLL, arm/gpu/vpu/sys use 1416X PLL, define 2 PLL clock
structure for each group is enough.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PLL14xx on imx8m can change the S and K parameter without requiring
a reset and relock of the whole PLL.
Fix clk_pll144xx_mp_change register reading and use it for pll1443 as
well since no reset+relock is required on K changes either.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pll BYPASS bit should be kept inside pll driver for glitchless freq
setting following spec. If exposing the bit, that means pll driver and
clk driver has two paths to touch this bit, which is wrong.
So use EXT_BYPASS bit here.
And drop uneeded set parent, because EXT_BYPASS default is 0.
Suggested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-5-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pll BYPASS bit should be kept inside pll driver for glitchless freq
setting following spec. If exposing the bit, that means pll driver and
clk driver has two paths to touch this bit, which is wrong.
So use EXT_BYPASS bit here.
And drop uneeded set parent, because EXT_BYPASS default is 0.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Suggested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-4-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When registering the PLL, unbypass the PLL.
The PLL has two bypass control bit, BYPASS and EXT_BYPASS.
we will expose EXT_BYPASS to clk driver for mux usage, and keep
BYPASS inside pll14xx usage. The PLL has a restriction that
when M/P change, need to RESET/BYPASS pll to avoid glitch, so
we could not expose BYPASS.
To make it easy for clk driver usage, unbypass PLL which does
not hurt current function.
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-3-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to PLL1443XA and PLL1416X spec,
"When BYPASS is 0 and RESETB is changed from 0 to 1, FOUT starts to
output unstable clock until lock time passes. PLL1416X/PLL1443XA may
generate a glitch at FOUT."
So set BYPASS when RESETB is changed from 0 to 1 to avoid glitch.
In the end of set rate, BYPASS will be cleared.
When prepare clock, also need to take care to avoid glitch. So
we also follow Spec to set BYPASS before RESETB changed from 0 to 1.
And add a check if the RESETB is already 0, directly return 0;
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-2-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN supports CPU running at 1.5GHz/1.4GHz/1.2GHz, add missing
frequency for ARM PLL table.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add .rate_count assignment which is necessary for searching required
PLL rate from the each PLL table.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To Frac pll, the gate shift is 13, however to Int PLL the gate shift
is 11.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is enabled by default but if it's not explicitly defined and marked
as critical then its parent might get turned off.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* Replace to audio_pll2_clk with audio_pll2_out
* Replace sys3_pll2_out with sys_pll3_out
* Replace sys1_pll_40m with sys_pll1_40m
* qspi parent[2] is sys_pll2_333m not sys_pll1_800m
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* There is no video_pll2 on imx8mm, replace with dummy
* Replace reference to sys_pll3_clk with sys_pll3_out
* qspi parent[2] is sys_pll2_333m not sys_pll1_800m
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "sys3_pll2_out" CLK was removed in refactoring so all references
need to be updated to "sys3_pll_out"
Fixes: e9dda4af68 ("clk: imx: Refactor entire sccg pll clk")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When of_clk_add_provider failed, all clks should be unregistered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When of_clk_add_provider failed, all clks should be unregistered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Initially, the TMU_ROOT clock was marked as critical, which automatically
made the AHB clock to stay always on. Since the TMU_ROOT clock is not
marked as critical anymore, following commit:
"clk: imx8mq: Remove CLK_IS_CRITICAL flag for IMX8MQ_CLK_TMU_ROOT"
all the clocks that derive from ipg_root clock (and implicitly ahb clock)
would also have to enable, along with their own gate, the AHB clock.
But considering that AHB is actually a bus that has to be always on, we mark
it as critical in the clock provider driver and then all the clocks that
derive from it can be controlled through the dedicated per IP gate which
follows after the ipg_root clock.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Call imx_register_uart_clocks() API to keep uart clocks enabled
when earlyprintk or earlycon is active.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_register_uart_clocks_hws() function is NOT implemented
at all, remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Earlycon's clock could be disabled during kernel boot up,
if earlycon is enabled and its clock is gated, then kernel
boot up will fail. Make sure earlycon's clock is enabled
during kernel boot up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no strong reason for this to use CLK_OF_DECLARE instead
of being a platform driver. Plus, this will now be aligned with the
other i.MX8M clock drivers which are platform drivers.
In order to make the clock provider a platform driver
all the data and code needs to be outside of .init section.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has no sys3_pll2_out clock, PWM3 clock's mux option #4
should be sys_pll3_out, sys3_pll2_out is a typo, fix it.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that the i.MX6 and i.MX7 clock drivers have been switched to clk_hw based,
we can remove the clk based API that is not used by any i.MX clock driver.
The following APIs are going away now:
- imx_clk_busy_divider
- imx_clk_busy_mux
- imx_clk_fixup_divider
- imx_clk_fixup_mux
- imx_clk_mux_ldb
- imx_clk_gate_dis_flags
- imx_clk_gate_flags
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per latest imx8mq datasheet of CCM, the parent of usb1_ctrl_root_clk
and usb2_ctrl_root_clk is usb_bus.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX8MQ_CLK_TMU_ROOT is ONLY used for thermal module, the driver
should manage this clock, so no need to have CLK_IS_CRITICAL flag
set.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename 'share_count_dcss' to 'share_count_disp', since the
DCSS module does not exist on imx8mm platform. So rename it
to avoid any unnecessary confusion.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per latest imx8mm datasheet of CCM, the parent of usb1_ctrl_root_clk
should be usb_bus.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
