Pull sparc fixes from David Miller:
1) With modern networking cards we can run out of 32-bit DMA space, so
support 64-bit DMA addressing when possible on sparc64. From Dave
Tushar.
2) Some signal frame validation checks are inverted on sparc32, fix
from Andreas Larsson.
3) Lockdep tables can get too large in some circumstances on sparc64,
add a way to adjust the size a bit. From Babu Moger.
4) Fix NUMA node probing on some sun4v systems, from Thomas Tai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: drop duplicate header scatterlist.h
lockdep: Limit static allocations if PROVE_LOCKING_SMALL is defined
config: Adding the new config parameter CONFIG_PROVE_LOCKING_SMALL for sparc
sunbmac: Fix compiler warning
sunqe: Fix compiler warnings
sparc64: Enable 64-bit DMA
sparc64: Enable sun4v dma ops to use IOMMU v2 APIs
sparc64: Bind PCIe devices to use IOMMU v2 service
sparc64: Initialize iommu_map_table and iommu_pool
sparc64: Add ATU (new IOMMU) support
sparc64: Add FORCE_MAX_ZONEORDER and default to 13
sparc64: fix compile warning section mismatch in find_node()
sparc32: Fix inverted invalid_frame_pointer checks on sigreturns
sparc64: Fix find_node warning if numa node cannot be found
There's not much point, except compile test, enabling the stmmac
platform drivers unless the STM32 SoC is enabled. It's not
useful without it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
at91ether_start_xmit() does not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
sunbmac uses '__u32' for dma handle while invoking kernel DMA APIs,
instead of using dma_addr_t. This hasn't caused any 'incompatible
pointer type' warning on SPARC because until now dma_addr_t is of
type u32. However, recent changes in SPARC ATU (iommu) enables 64bit
DMA and therefore dma_addr_t becomes of type u64. This makes
'incompatible pointer type' warnings inevitable.
e.g.
drivers/net/ethernet/sun/sunbmac.c: In function ‘bigmac_ether_init’:
drivers/net/ethernet/sun/sunbmac.c:1166: warning: passing argument 3 of ‘dma_alloc_coherent’ from incompatible pointer type
./include/linux/dma-mapping.h:445: note: expected ‘dma_addr_t *’ but argument is of type ‘__u32 *’
This patch resolves above compiler warning.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sunqe uses '__u32' for dma handle while invoking kernel DMA APIs,
instead of using dma_addr_t. This hasn't caused any 'incompatible
pointer type' warning on SPARC because until now dma_addr_t is of
type u32. However, recent changes in SPARC ATU (iommu) enables 64bit
DMA and therefore dma_addr_t becomes of type u64. This makes
'incompatible pointer type' warnings inevitable.
e.g.
drivers/net/ethernet/sun/sunqe.c: In function ‘qec_ether_init’:
drivers/net/ethernet/sun/sunqe.c:883: warning: passing argument 3 of ‘dma_alloc_coherent’ from incompatible pointer type
./include/linux/dma-mapping.h:445: note: expected ‘dma_addr_t *’ but argument is of type ‘__u32 *’
drivers/net/ethernet/sun/sunqe.c:885: warning: passing argument 3 of ‘dma_alloc_coherent’ from incompatible pointer type
./include/linux/dma-mapping.h:445: note: expected ‘dma_addr_t *’ but argument is of type ‘__u32 *’
This patch resolves above compiler warnings.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to propagate errors from of_phy_register_fixed_link() which
can fail with -EPROBE_DEFER.
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to check for allocation failures before dereferencing a
NULL-pointer during probe.
Fixes: 649a1688c9 ("net: ethernet: ti: cpsw: create common struct to
hold shared driver data")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister the primary device in case the secondary emac
fails to probe.
kernel BUG at /home/johan/work/omicron/src/linux/net/core/dev.c:7743!
...
[<c05b3dec>] (free_netdev) from [<c04fe6c0>] (cpsw_probe+0x9cc/0xe50)
[<c04fe6c0>] (cpsw_probe) from [<c047b28c>] (platform_drv_probe+0x5c/0xc0)
Fixes: d9ba8f9e62 ("driver: net: ethernet: cpsw: dual emac interface
implementation")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop references taken and deregister devices registered
during probe on probe errors (including deferred probe) and driver
unbind.
Specifically, PHY of-node references were never released and fixed-link
PHY devices were never deregistered.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister all child devices also on probe errors to avoid
leaks and to fix probe deferral:
cpsw 4a100000.ethernet: omap_device: omap_device_enable() called from invalid state 1
cpsw 4a100000.ethernet: use pm_runtime_put_sync_suspend() in driver?
cpsw: probe of 4a100000.ethernet failed with error -22
Add generic helper to undo the effects of cpsw_probe_dt(), which will
also be used in a follow-on patch to fix further leaks that have been
introduced more recently.
Note that the platform device is now runtime-resumed before registering
any child devices in order to make sure that it is synchronously
suspended after having deregistered the children in the error path.
Fixes: 1fb19aa730 ("net: cpsw: Add parent<->child relation support
between cpsw and mdio")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_find_device_by_node() when
looking up an mdio device from a phy_id property during probe.
Fixes: 549985ee9c ("cpsw: simplify the setup of the register
pointers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to keep the platform device runtime-resumed throughout probe
to avoid accessing the CPSW registers in the error path (e.g. for
deferred probe) with clocks disabled:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0872d08
...
[<c04fabcc>] (cpsw_ale_control_set) from [<c04fb8b4>] (cpsw_ale_destroy+0x2c/0x44)
[<c04fb8b4>] (cpsw_ale_destroy) from [<c04fea58>] (cpsw_probe+0xbd0/0x10c4)
[<c04fea58>] (cpsw_probe) from [<c047b2a0>] (platform_drv_probe+0x5c/0xc0)
Fixes: df828598a7 ("netdev: driver: ethernet: Add TI CPSW driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 frequently crashes during machine shutdown with:
sky2_get_stats+0x60/0x3d8 [sky2]
dev_get_stats+0x68/0xd8
rtnl_fill_stats+0x54/0x140
rtnl_fill_ifinfo+0x46c/0xc68
rtmsg_ifinfo_build_skb+0x7c/0xf0
rtmsg_ifinfo.part.22+0x3c/0x70
rtmsg_ifinfo+0x50/0x5c
netdev_state_change+0x4c/0x58
linkwatch_do_dev+0x50/0x88
__linkwatch_run_queue+0x104/0x1a4
linkwatch_event+0x30/0x3c
process_one_work+0x140/0x3e0
worker_thread+0x60/0x44c
kthread+0xdc/0xf0
ret_from_fork+0x10/0x50
This is caused by the sky2 being called after it has been shutdown.
A previous thread about this can be found here:
https://lkml.org/lkml/2016/4/12/410
An alternative fix is to assure that IFF_UP gets cleared by
calling dev_close() during shutdown. This is similar to what the
bnx2/tg3/xgene and maybe others are doing to assure that the driver
isn't being called following _shutdown().
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing synchronize_net() call to avoid potential use after free,
since we explicitly call napi_hash_del() to factorize the RCU grace
period.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi_hash_del() before netif_napi_del() is dangerous
if a synchronize_rcu() is not enforced before NAPI struct freeing.
Lets leave this detail to core networking stack and feel
more comfortable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi_hash_del() before netif_napi_del() is dangerous
if a synchronize_rcu() is not enforced before NAPI struct freeing.
Lets leave this detail to core networking stack and feel
more comfortable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following
1. When interface is being teardown and queues are being cleaned up,
free pending SKBs that are in SQ which are either not transmitted
or freed as NAPI is disabled by that time.
2. While interface initialization, delay CFG_DONE notification till
the end to avoid corner cases where TXQs are enabled but CQ
interrupts are not which results blocking transmission and kicking
off watchdog.
3. Check for IFF_UP while re-enabling RBDR interrupts from tasklet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes multiple issues
1. Convert all driver statistics to percpu counters for accuracy.
2. To avoid multiple CQEs posted by a TSO packet appended to HW,
TSO pkt's SQE has 'post_cqe' not set but a dummy SQE is added
for getting HW transmit completion notification. This dummy
SQE has 'dont_send' set and HW drops the pkt pointed to in this
thus Tx drop counter increases. This patch fixes this by subtracting
SW tx tso counter from HW Tx drop counter for actual packet drop counter.
3. Reset all individual queue's and VNIC HW stats when interface is going down.
4. Getrid off unnecessary counters in hot path.
5. Bringout all CQE error stats i.e both Rx and Tx.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes enabling of HW verification of L3/L4 length and
TCP/UDP checksum which is currently being cleared. Also fixed VLAN
stripping config which is being cleared when multiqset is enabled.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programming LMAC credits taking 9K frame size by default is incorrect
as for an interface which is one of the many on the same BGX/QLM
no of credits available will be less as Tx FIFO will be divided
across all interfaces. So let's say a BGX with 40G interface and another
BGX with multiple 10G, bandwidth of 10G interfaces will be effected when
traffic is running on both 40G and 10G interfaces simultaneously.
This patch fixes this issue by programming credits based on netdev's MTU.
Also fixed configuring MTU to HW and added CQE counter for pkts which
exceed this value.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the 'bgx_id' determination on 83xx where there are
4 BGX blocks instead of 2 on other platforms.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch disable capturing multicast packets when multicast mode
disabled for ethernet ('ifconfig eth0 -multicast'). In that case
no multicast packet will be passed to kernel.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast support was implemented by commit 775dd682e2
('arc_emac: implement promiscuous mode and multicast filtering').
It can be enabled explicity using 'ifconfig eth0 multicast'.
The patch is needed in order to remove explicit configuration
as most devices has multicast mode enabled by default.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the ethtool stats for PTP frames; previous
version does not take care about some message types: i.e.
announce, management and signaling. It also provided a
broken statistic in case of "No PTP message received".
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to bad management of the descriptors, when use ptp4l,
kernel panics as shown below:
-----------------------------------------------------------
Unable to handle kernel NULL pointer dereference at virtual
address 000001ac
...
Internal error: Oops: 17 [#1] SMP ARM
...
Hardware name: STi SoC with Flattened Device Tree
task: c0c05e80 task.stack: c0c00000
PC is at dwmac4_wrback_get_tx_timestamp_status+0x0/0xc
LR is at stmmac_tx_clean+0x2f8/0x4d4
-----------------------------------------------------------
In case of GMAC4 the extended descriptor pointers were
used for getting the timestamp. These are NULL for this HW,
and the normal ones must be used.
The PTP also had problems on this chip due to the bad
register management and issues on the algo adopted to
setup the PTP and getting the timestamp values from the
descriptors.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to update this file by using BIT macros, removing
not used defines and fixes some typos.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSE PCS SGMII ethernet has an issue where switching speed doesn't work
caused by a faulty register macro offset. This fixes the issue.
Signed-off-by: Jia Jie Ho <ho.jia.jie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b45f64d16d ("mlxsw: spectrum_router: Use FIB notifications
instead of switchdev calls") we reflect to the device the entire FIB
table and not only FIBs that point to netdevs created by the driver.
During module removal, FIBs of the second type are removed following
NETDEV_UNREGISTER events sent. The other FIBs are still present in both
the driver's cache and the device's table.
Fix this by iterating over all the FIB tables in the device and flush
them. There's no need to take locks, as we're the only writer.
Fixes: b45f64d16d ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 52f95bbfcf ("stmmac: fix adjust link call in case of a switch
is attached") added some logic to avoid polling the fixed PHY and
therefore invoking the adjust_link callback more than once, since this
is a fixed PHY and link events won't be generated.
This works fine the first time, because we start with phydev->irq =
PHY_POLL, so we call adjust_link, then we set phydev->irq =
PHY_IGNORE_INTERRUPT and we stop polling the PHY.
Now, if we called ndo_close(), which calls both phy_stop() and does an
explicit netif_carrier_off(), we end up with a link down. Upon calling
ndo_open() again, despite starting the PHY state machine, we have
PHY_IGNORE_INTERRUPT set, and we generate no link event at all, so the
link is permanently down.
Fixes: 52f95bbfcf ("stmmac: fix adjust link call in case of a switch is attached")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In-flight DMA from 1st kernel could continue going in kdump kernel.
New io-page table has been created before bnx2 does reset at open stage.
We have to wait for the in-flight DMA to complete to avoid it look up
into the newly created io-page table at probe stage.
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3e1be7ad2d.
When people build bnx2 driver into kernel, it will fail to detect
and load firmware because firmware is contained in initramfs and
initramfs has not been uncompressed yet during do_initcalls. So
revert commit 3e1be7a and work out a new way in the later patch.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake "unmached" to "unmatched" in
debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake "successed" to "succeeded"
in debug message. Also unwrap multi-line literal string.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mistake was causing debugfs directory creation
failures when multiple ibmvnic devices were probed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure was mapped but never subsequently unmapped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_copy_channel() doesn't correctly clear the napi_hash related state.
This means that when napi_hash_add is called for that channel nothing is
done, and we are left with a copy of the napi_hash_node from the old
channel. When we later call napi_hash_del() on this channel we have a
stale napi_hash_node.
Corruption is only seen when there are multiple entries in one of the
napi_hash lists. This is made more likely by having a very large number
of channels. Testing was carried out with 512 channels - 32 channels on
each of 16 ports.
This failure typically appears as protection faults within napi_by_id()
or napi_hash_add(). efx_copy_channel() is only used when tx or rx ring
sizes are changed (ethtool -G).
Fixes: 36763266bb ("sfc: Add support for busy polling")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device's neighbour table is periodically dumped in order to update
the kernel about active neighbours. A single dump session may span
multiple queries, until the response carries less records than requested
or when a record (can contain up to four neighbour entries) is not full.
Current code stops the session when the number of returned records is
zero, which can result in infinite loop in case of high packet rate.
Fix this by stopping the session according to the above logic.
Fixes: c723c735fa ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When binding port to a newly created span entry, its refcount is
initialized to zero even though it has a bound port. That leads
to unexpected behaviour when the user tries to delete that port
from the span entry.
Fix this by initializing the reference count to 1.
Also add a warning to put function.
Fixes: 763b4b70af ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the physical link is down and the VF virtual link is set to "enable",
the current code does not always work. If the link is down but the
cable is attached, the firmware returns LINK_SIGNAL instead of
NO_LINK. The current code is treating LINK_SIGNAL as link up.
The fix is to treat link as down when the link_status != LINK.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic is missing the check on whether the tx and rx rings are sharing
completion rings or not.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now, the table with same id in multiple netnamespaces were squashed
to a single virtual router. That is not only incorrect, it also causes
error messages when trying to use RALUE register to do double remove
of FIB entries, like this one:
mlxsw_spectrum 0000:03:00.0: EMAD reg access failed (tid=facb831c00007b20,reg_id=8013(ralue),type=write,status=7(bad parameter))
Since we don't allow ports to change namespaces (NETIF_F_NETNS_LOCAL),
and the infrastructure is not yet prepared to handle netnamespaces, just
ignore FIB notification events for non-init namespaces. That is clear to
do since we don't need to offload them.
Fixes: b45f64d16d ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__neigh_create function works in a different way than assumed.
It passes "n" as a parameter to ndo_neigh_construct. But this "n" might
be destroyed right away before __neigh_create() returns in case there is
already another neighbour struct in the hashtable with the same dev and
primary key. That is not expected by mlxsw_sp_router_neigh_construct()
and the stored "n" points to freed memory, eventually leading to crash.
Fix this by doing tight 1:1 coupling between neighbour struct and
internal driver neigh_entry. That allows to narrow down the key in
internal driver hashtable to do lookups by "n" only.
Fixes: 6cf3c971dc ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous fix has broken RoCE support as the rdma_pf_params are now
being set into the parameters only after the params are alrady assigned
into the hw-function.
Fixes: 0189efb8f4 ("qed*: Fix Kconfig dependencies with INFINIBAND_QEDR")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently RoCE v2 won't operate with RDMA CM due to missing setting of
the roce-flavour in the ll2 configuration.
This patch properly sets the flavour, and deletes incorrect HSI
that doesn't [yet] exist.
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the opt_* fields to determine the starting point for negotiating the
number of tx/rx completion queues with the vnic server. These contain the
number of queues that the vnic server estimates that it will be able to
allocate. While renegotiation may still occur, using the opt_* fields will
reduce the number of times this needs to happen and will prevent driver
probe timeout on systems using large numbers of ibmvnic client devices per
vnic port.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY has been configured to allow pause frames, then the MAC
should be configured to generate and/or accept those frames.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause frames are used to enable flow control. A MAC can send and
receive pause frames in order to throttle traffic. However, the PHY
must be configured to allow those frames to pass through.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes regression introduced by patch adding feature flags. It was
already reported and patch followed (it got accepted) but it appears it
was incorrect. Instead of fixing reversed condition it broke a good one.
This patch was verified to actually fix SoC hanges caused by bgmac on
BCM47186B0.
Fixes: db791eb297 ("net: ethernet: bgmac: convert to feature flags")
Fixes: 4af1474e61 ("net: bgmac: Fix errant feature flag check")
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We received two reports of BUG_ON in bnad_txcmpl_process() where
hw_consumer_index appeared to be ahead of producer_index. Out of order
write/read of these variables could explain these reports.
bnad_start_xmit(), as a producer of tx descriptors, has a few memory
barriers sprinkled around writes to producer_index and the device's
doorbell but they're not paired with anything in bnad_txcmpl_process(), a
consumer.
Since we are synchronizing with a device, we must use mandatory barriers,
not smp_*. Also, I didn't see the purpose of the last smp_mb() in
bnad_start_xmit().
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 9d2afba058.
The original issue would possibly exist if an external module
tried calling our "ethtool_ops" without checking if it still
exists.
The right way of solving it is by simply doing the check in
the caller side.
Currently, no action is required as there's no such use case.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
