[why]
Gamma was always being set as identity on SDR monitor,
leading to no changes in gamma. This caused nightlight to
not apply correctly.
[how]
Added a default gamma structure to compare against
in the sdr case.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HUBP underflow is never cleared, which causes underflow in one
test to fail another test, violating the independence requirements
[how]
Rather than make clearing implicit, we explicitly clear underflow
status in DTN.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_state has an array of dc_stream_status that contain
pointers to the dc_plane_state and other useful information
Confusingly, dc_stream_state also contains a dc_stream_status
called status. This struct was partially initialized and
used in a few places
[How]
stream->status.link has been replaced with stream->sink->link.
If a stream does not have a sink, or a sink does not have a link,
something has gone seriously wrong
All other properties of stream->status were zeroed by kzalloc
and never initialized, so they have been replaced by the number 0
This is a refactor: no functional change is intended
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to disable EDP backlight when enter S4 with EDP only
and resume from S4 with secondary only.
[How]
Align the real hw and sw state via vBios scratch register in
function enable_accelerated_mode when resume from S4.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When going to full-screen mode commit_planes_for_stream tries to decrease
dcf_deep_sleep value, but safe_to_lower is false, so we don't send the new value
to SMU but dc context gets updated.
Later when dc_post_update_surfaces_to_stream tries to lower dcf_ds when
safe_to_lower is true, this check prevents the message from being sent.
[How]
Remove the check that compares new value with what is stored in dc_context.
This check is not necessary as dcn1_update_clocks already checks if the value
is different from the current dcf_dp value.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
This is based on HW programming guide update.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN we want direct DC to SMU calls, with minimal interference from
pplib.
The reason for each pp_smu interface mapping to 1 SMU message is so we
can have the sequencing of different SMU message in DC and shared across
different OS's.
This will also simplify debugging as DAL owns this interaction and
there's no confusion about division of ownership.
[How]
Part 4: Change clock units so they match the values PPLib sends to SMU.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] On DCN1/DCE, There are two functions programming OCSC:
program_csc_matrix and program_output_csc. They do the same thing.
[How] Consolidate to use only program_output_csc.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They are no longer relevant
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Set gamma not working on certain planes in MPO configuration
Root cause is that video format (YUV-420) isn't allowed for IGAM where
gamma is applied.
Fix is not easy though:
1. allowing will not work because IGAM is before ICSC so RGB gamma would
be applied on YUV pixels.
2. Moving OS gamma to DGAM or RGAM resulted in weird artifacts.
Ultimately the root cause for these artifacts was due to handling end
points and the fact that YUV->RGB conversion will frequently "overshoot"
FP 1.0 value. DCE has a single end point and slope, so we would take max.
In nightlight mode, blue channel is reduced, sometimes to flat 0 line,
but red is virtually unchanged. Any "overshot" in blue will be clipped
to 1 (max R,G,B) instead of max blue value.
[How]
Fortunately, this can be fixed on DCN where we have end point and slope
for all three color channels. We cannot fix this problem on DCE.
Other things fixed:
- switch (back) to using RGAM for OS gamma instead of IGAM
- add coeffs for 709 YUV->RGB (we used RGB->YUV for both conversions)
- switch color temperature method to scaled bradford - otherwise we would
have clipping problems that caused us to switch to IGAM for OS gamma
in the first place.
- comments and some minor improvements - there are some more issues but
they will be addressed in separate commits.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN we want direct DAL to SMU calls, with as little as
possible interference by pplib. The reason for each pp_smu interface
mapping to 1 SMU message is so we can have the sequencing of different
SMU message in dal and shared across different OS. This will also
simplify debugging as DAL owns this interaction and there's no
confusion about division of ownership.
[How]
Separate the set_hard_min_fclk_by_freq message from the
SMU messages that are sent as part of pp_rv_set_display_requirement.
directly notify min dcfclk to smu part 2
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds the hw block as well as hooks up dppclk dto
programming
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation for adding the actual dccg block since the
current implementation of dccg is mor eof a clock manager
than a hw block
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN we want direct DAL to SMU calls, with as little as possible
interference by pplib. The reason for each pp_smu interface mapping to
1 SMU message is so we can have the sequencing of different SMU message
in dal and shared across different OS. This will also simplify
debugging as DAL owns this interaction and there's no confusion about
division of ownership.
[How]
Part 2: Separate set_min_deep_sleep_dcfclk message from the SMU
messages that are sent as part of dm_pp_apply_clock_for_voltage_request.
Directly notify min dcfclk to smu
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN we want direct DAL to SMU calls, with as little as possible
interference by pplib. The reason for each pp_smu interface mapping
to 1 SMU message is so we can have the sequencing of different SMU
message in dal and shared across different OS. This will also simplify
debugging as DAL owns this interaction and there's no confusion about
division of ownership.
[How]
Part 1: Separate set_min_deep_Sleep_dcfclk message from the SMU
messages that are sent as part of dcn10_pplib_apply_display_requirements.
Notify deep sleep dcfclk to smu directly
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need separate feature flag for DP 4:2:0 support, since existing
flag is used for HDMI
[How]
Added dp_ycbcr420_supported to struct encoder_feature_support
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous logic to update display count in commit_planes_do_stream_update
doesn't cover all cases.
[How]
Update display count as part of clock updates. Count virtual stream
as active to work around headless situation.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make these functions non static and define registers for future use
is_lower_pipe_tree_visible();
is_upper_pipe_tree_visible();
is_pipe_tree_visible();
dcn10_program_pte_vm();
set_hdr_multiplier();
update_dchubp_dpp()
find_top_pipe_for_stream()
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Freesync 2 HDR and support for HDR content
outside the range of the HDR display
require implementation on Dal 3 to better match
Dal2.
[How]
Add support for Freesync HDR and mapping
of source content to display ranges for better
representation of HDR content.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently dccg contains code related to every dcn revision in
a single file.
This change splits out the dcn parts of code into correct folders
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is done to keep things more readable, avoids a true/false flag
in dc interface layer.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is done to clear up the clock programming sequence
since the only time we need to notify pplib is after
clock update.
This also renames the clk block to dccg, at the moment
this block contains both clock management and dccg
functionality.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When vstartup is larger than vblank end we need to set v_fp2
to allow for this early start
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RV2 resource is limit to 3 pipes. Limitation should apply to all HW
blocks instead of front pipe.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong index for pstate debug test register
[How]
Add correct index value for dcn1_01 in hubbub1_construct()
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to a small pre-fetch window, the active vline timing is a couple
of lines off when compared to what it should be.
[How]
Changed the calculation for the start vline to account for this window.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description] interlace mode shows wrong vertical timing.
Interface timing in Edid is half vertical timing as progressive timing.
driver doubled the vertical timing in edid_paser,
no need to double in optc again.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
ddc engines were recently changed to be independently tracked
from pipe count. the change was reflected in resource constructor
but not in destructor. this manifests as a memory leak when
pipe harvesting is enabled, since not all constructed ddc engines
are freed
[how]
make destructor symmetric with constructor for all dcX_resource
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF keeps awake after S0i3 resume due to DRAM_STATE_CNTL
is set by bios command table during dcn init_hw.
[How]
As a work around, check STATE_CNTL status before init_hw,
if it is 0 before init_hw and set to 1 after init_hw,
change it to 0.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All ASICS we support has YCbCr support, so
the check is unnecessary, the currently logic
in validate output also returns true all
the time, so the unneccessary logic is removed
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently not supported, will black screen when set.
[How]
Fail validate timing helper for those modes.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously bandwidth validation was failing because swizzle mode was not
initialized during plane_state allocation. The swizzle mode was
calculated using pixed format which is how swizzle mode is initially
calculated in addrlib.
[How]
* Set default swizzle mode for validation to DC_SW_UNKNOWN
* Created new function in dcn10_assign_swizzle_mode which sets the
plane swizzle mode based on selected pixed format
* Added the call of assign_swizzle_mode into dc_validate_global_state
* Set failsafe swizzle mode back to DC_SW_LINEAR
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FPGA doesn't program backend, so we don't need certain link settings
(audio stream for example).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clock sources currently have support for asic specific
function pointers. But actual separation into functions
was never performed, leaving us with giant functions that
rely on switch.
This change creates separate functions, removing switch use.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We were not providing the correct pixel clocks to DML for marks
calculation.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add Raven2 definitions in the dc code
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Existing debug dump are all invariant, new “low 32-bit of address”
dump is not invariant
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
AMD Stoney reference board, there are only 2 pipes (not include
underlay), and 3 connectors. resource creation, only
2 I2C/AUX engines are created. Within dc_link_aux_transfer, when
pin_data_en =2, refer to enengines[ddc_pin->pin_data->en] = NULL.
NULL point is referred later causing system crash.
[how]
each asic design has fixed number of ddc engines at hw side.
for each ddc engine, create its i2x/aux engine at sw side.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Although 4 unique register values exist for gamma modes, two are
actually the same (the two RAMs) It’s not possible for caller to
understand this HW specific behavior, so some parsing is necessary
in driver
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]Update Code to get DTN golden log check to pass for tests run after
DAL217 tests.
[How]Change how dcn10_log_hw_state function prints HW state info
(CM_GAMUT_REMAP_Cx_Cx registers) when GAMUT REMAP is in bypass mode.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Logging hardware state can be done by triggering a write to the
debugfs file. It would also be useful to be able to read the hardware
state from the debugfs file to be able to generate a clean log without
timestamps.
[How]
Usage: cat /sys/kernel/debug/dri/0/amdgpu_dm_dtn_log
Threading is an obvious concern when dealing with multiple debugfs
operations and blocking on global state in dm or dc seems unfavorable.
Adding an extra parameter for the debugfs log context state is the
implementation done here. Existing code that made use of DTN_INFO
and its associated macros needed to be refactored to support this.
We don't know the size of the log in advance so it reallocates the
log string dynamically. Once the log has been generated it's copied
into the user supplied buffer for the debugfs. This allows for seeking
support but it's worth nothing that unlike triggering output via
dmesg the hardware state might change in-between reads if your buffer
size is too small.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix comile warning like,
CC [M] drivers/gpu/drm/i915/gvt/execlist.o
CC [M] drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.o
CC [M] drivers/gpu/drm/radeon/btc_dpm.o
CC [M] drivers/isdn/hisax/avm_a1p.o
CC [M] drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_dpp.o
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c: In function ‘dcn10_update_mpcc’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:1903:9: warning: missing braces around initializer [-Wmissing-braces]
struct mpcc_blnd_cfg blnd_cfg = {0};
^
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:1903:9: warning: (near initialization for ‘blnd_cfg.black_color’) [-Wmissing-braces]
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Existing DTN infrastructure in driver is hacky. It uses implicit log
names, and also incorrect escape ID.
[how]
- Implement using generic DTN escape ID.
- Move file logging functionality from driver to to script; driver now outputs to string/buffer
- Move HWSS debug functionality to separate c file
- Add debug functionalty for per-block logging as CSV
- Add pretty print in python
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Define register for dcn10 for future changes
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I2C code did not match dc resource model and was generally
unpleasant
[How]
Move code into new svelte dce_i2c files, replacing various i2c
objects with two structs: dce_i2c_sw and dce_i2c_hw. Fully split
sw and hw code paths. Remove all redundant declarations. Use
address lists to distinguish between versions. Change dce80 code
to newer register access macros.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- program infoframe for Stereo
- program stereo flip control registers properly
v2: Add missing license headers
Signed-off-by: Alvin lee <alvin.lee3@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove dependency on internal sink map and instead
use existing stream and plane state
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are outstanding bugs for PIP in Dal3:
-Crash when toggling PIP visibility
-Global Alpha is not working, Adjusting global alpha
doesn’t have an effect
-Cursor is not working with pip plane and pipe splits
-One flash occurs when cursor enters PIP plane from
top/bottom
-Crash when moving PIP plane off the screen
[How]
Resolve divide by 0 error
Implement global alpha
Program cursor on all pipes
Add dst rects' x and y offests into cursor position
Disable cursor when it is beyond bottom/top edge
Signed-off-by: Gloria Li <geling.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is currently a dependency on the order in which tests are executed.
This is because the non-relevant state info is being printed, which results
in the output based on the state from the previous test.
[how]
Print DPP DTN log only if the pipe is enabled.
In addition to the affected per-submission DTN golden logs, included in this
change is also DTN golden log update for pre-submission tests.
The other DTN golden logs affected by this change will be updated upon
nightly test run (which will generate the updated DTN logs).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
