Adds the new procfs knobs:
/proc/sys/net/ipv4/conf/*/igmpv2_unsolicited_report_interval
/proc/sys/net/ipv4/conf/*/igmpv3_unsolicited_report_interval
Which will allow userspace configuration of the IGMP unsolicited report
interval (see below) in milliseconds. The defaults are 10000ms for IGMPv2
and 1000ms for IGMPv3 in accordance with RFC2236 and RFC3376.
Background:
If an IGMP join packet is lost you will not receive data sent to the
multicast group so if no data arrives from that multicast group in a
period of time after the IGMP join a second IGMP join will be sent. The
delay between joins is the "IGMP Unsolicited Report Interval".
Prior to this patch this value was hard coded in the kernel to 10s for
IGMPv2 and 1s for IGMPv3. 10s is unsuitable for some use-cases, such as
IPTV as it can cause channel change to be slow in the presence of packet
loss.
This patch allows the value to be overridden from userspace for both
IGMPv2 and IGMPv3 such that it can be tuned accoding to the network.
Tested with Wireshark and a simple program to join a (non-existent)
multicast group. The distribution of timings for the second join differ
based upon setting the procfs knobs.
igmpvX_unsolicited_report_interval is intended to follow the pattern
established by force_igmp_version, and while a procfs entry has been added
a corresponding sysctl knob has not as it is my understanding that sysctl
is deprecated[1].
[1]: http://lwn.net/Articles/247243/
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The procfs knob /proc/sys/net/ipv4/conf/*/force_igmp_version allows the
IGMP protocol version to use to be explicitly set. As a side effect this
caused the routing cache to be flushed as it was declared as a
DEVINET_SYSCTL_FLUSHING_ENTRY. Flushing is unnecessary and this patch
makes it so flushing does not occur.
Requested by Hannes Frederic Sowa as he was reviewing other patches
adding procfs entries.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5c766d642 ("ipv4: introduce address lifetime") leaves the ifa
resource that was allocated via inet_alloc_ifa() unfreed when returning
the function with -EINVAL. Thus, free it first via inet_free_ifa().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ifa->ifa_label" is an array inside the in_ifaddr struct. It can never
be NULL so we can remove this check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the uses of this unnecessary typedef.
Done via perl script:
$ git grep --name-only -w ctl_table net | \
xargs perl -p -i -e '\
sub trim { my ($local) = @_; $local =~ s/(^\s+|\s+$)//g; return $local; } \
s/\b(?<!struct\s)ctl_table\b(\s*\*\s*|\s+\w+)/"struct ctl_table " . trim($1)/ge'
Reflow the modified lines that now exceed 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After IP route cache removal, multicast applications using
a lot of multicast addresses hit a O(N) behavior in ip_check_mc_rcu()
Add a per in_device hash table to get faster lookup.
This hash table is created only if the number of items in mc_list is
above 4.
Reported-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
move might_sleep operations out of the rcu_read_lock() section.
Also fix iterating over ifa_dev->ifa_list
Introduced by: commit 5c766d642b "ipv4: introduce address lifetime"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will result in calling check_lifetime in nearest opportunity and
that function will adjust next time to call check_lifetime correctly.
Without this, check_lifetime is called in time computed by previous run,
not affecting modified lifetime.
Introduced by: commit 5c766d642b "ipv4: introduce address lifetime"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
if userspace changes lifetime of address, send netlink notification and
call notifier.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes benefit of dev_addr_genid and dev_base_seq to check if a change
occurs during a netlink dump. If a change is detected, the flag NLM_F_DUMP_INTR
is set in the first message after the dump was interrupted.
Note that seq and prev_seq must be reset between each family in rtnl_dump_all()
because they are specific to each family.
Reported-by: Junwei Zhang <junwei.zhang@6wind.com>
Reported-by: Hongjun Li <hongjun.li@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With decnet converted, we can finally get rid of rta_buf and its
computations around it. It also gets rid of the minimal header
length verification since all message handlers do that explicitly
anyway.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's useful to be able to get the initial state of all entries. The patch adds
the support for IPv4 and IPv6.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some usecase when lifetime of ipv4 addresses might be helpful.
For example:
1) initramfs networkmanager uses a DHCP daemon to learn network
configuration parameters
2) initramfs networkmanager addresses, routes and DNS configuration
3) initramfs networkmanager is requested to stop
4) initramfs networkmanager stops all daemons including dhclient
5) there are addresses and routes configured but no daemon running. If
the system doesn't start networkmanager for some reason, addresses and
routes will be used forever, which violates RFC 2131.
This patch is essentially a backport of ivp6 address lifetime mechanism
for ipv4 addresses.
Current "ip" tool supports this without any patch (since it does not
distinguish between ipv4 and ipv6 addresses in this perspective.
Also, this should be back-compatible with all current netlink users.
Reported-by: Pavel Šimerda <psimerda@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NULL pointer check `!ifa' should come before its first use.
[ Bug origin : commit fd23c3b311
(ipv4: Add hash table of interface addresses) in linux-2.6.39 ]
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch advertise the MC_FORWARDING status for IPv4 and IPv6.
This field is readonly, only multicast engine in the kernel updates it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an unpriviled user who has created a user namespace, and then
created a network namespace to effectively use the new network
namespace, by reducing capable(CAP_NET_ADMIN) and
capable(CAP_NET_RAW) calls to be ns_capable(net->user_ns,
CAP_NET_ADMIN), or capable(net->user_ns, CAP_NET_RAW) calls.
Settings that merely control a single network device are allowed.
Either the network device is a logical network device where
restrictions make no difference or the network device is hardware NIC
that has been explicity moved from the initial network namespace.
In general policy and network stack state changes are allowed
while resource control is left unchanged.
Allow creating raw sockets.
Allow the SIOCSARP ioctl to control the arp cache.
Allow the SIOCSIFFLAG ioctl to allow setting network device flags.
Allow the SIOCSIFADDR ioctl to allow setting a netdevice ipv4 address.
Allow the SIOCSIFBRDADDR ioctl to allow setting a netdevice ipv4 broadcast address.
Allow the SIOCSIFDSTADDR ioctl to allow setting a netdevice ipv4 destination address.
Allow the SIOCSIFNETMASK ioctl to allow setting a netdevice ipv4 netmask.
Allow the SIOCADDRT and SIOCDELRT ioctls to allow adding and deleting ipv4 routes.
Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls for
adding, changing and deleting gre tunnels.
Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls for
adding, changing and deleting ipip tunnels.
Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls for
adding, changing and deleting ipsec virtual tunnel interfaces.
Allow setting the MRT_INIT, MRT_DONE, MRT_ADD_VIF, MRT_DEL_VIF, MRT_ADD_MFC,
MRT_DEL_MFC, MRT_ASSERT, MRT_PIM, MRT_TABLE socket options on multicast routing
sockets.
Allow setting and receiving IPOPT_CIPSO, IP_OPT_SEC, IP_OPT_SID and
arbitrary ip options.
Allow setting IP_SEC_POLICY/IP_XFRM_POLICY ipv4 socket option.
Allow setting the IP_TRANSPARENT ipv4 socket option.
Allow setting the TCP_REPAIR socket option.
Allow setting the TCP_CONGESTION socket option.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- In rtnetlink_rcv_msg convert the capable(CAP_NET_ADMIN) check
to ns_capable(net->user-ns, CAP_NET_ADMIN). Allowing unprivileged
users to make netlink calls to modify their local network
namespace.
- In the rtnetlink doit methods add capable(CAP_NET_ADMIN) so
that calls that are not safe for unprivileged users are still
protected.
Later patches will remove the extra capable calls from methods
that are safe for unprivilged users.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting the creation of network namespaces
by unprivileged users, modify all of the per net sysctl exports
and refuse to allow them to unprivileged users.
This makes it safe for unprivileged users in general to access
per net sysctls, and allows sysctls to be exported to unprivileged
users on an individual basis as they are deemed safe.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This message allows to get the devconf for an interface.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change return value from -EACCES to -EPERM when the permission check fails.
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since route cache deletion (89aef8921b), delay is no
more used. Remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a frequent mistake to confuse the netlink port identifier with a
process identifier. Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.
I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.
I have successfully built an allyesconfig kernel with this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since route cache deletion (89aef8921b), delay is no
more used. Remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biederman pointed out that not holding RTNL while calling
call_netdevice_notifiers() was racy.
This patch is a direct transcription his feedback
against commit 0115e8e30d (net: remove delay at device dismantle)
Thanks Eric !
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed extra one second delay in device dismantle, tracked down to
a call to dst_dev_event() while some call_rcu() are still in RCU queues.
These call_rcu() were posted by rt_free(struct rtable *rt) calls.
We then wait a little (but one second) in netdev_wait_allrefs() before
kicking again NETDEV_UNREGISTER.
As the call_rcu() are now completed, dst_dev_event() can do the needed
device swap on busy dst.
To solve this problem, add a new NETDEV_UNREGISTER_FINAL, called
after a rcu_barrier(), but outside of RTNL lock.
Use NETDEV_UNREGISTER_FINAL with care !
Change dst_dev_event() handler to react to NETDEV_UNREGISTER_FINAL
Also remove NETDEV_UNREGISTER_BATCH, as its not used anymore after
IP cache removal.
With help from Gao feng
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use net_hash_mix(net) instead of hash_ptr(net, 8), and use
hash_32() instead of using a serie of XOR
Define IN4_ADDR_HSIZE_SHIFT for clarity
__ip_dev_find() can perform the net_eq() call only if ifa_local
matches the key, to avoid unneeded dereferences.
remove inline attributes
# size net/ipv4/devinet.o.before net/ipv4/devinet.o
text data bss dec hex filename
17471 2545 2048 22064 5630 net/ipv4/devinet.o.before
17335 2545 2048 21928 55a8 net/ipv4/devinet.o
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing of 127/8 is tradtionally forbidden, we consider
packets from that address block martian when routing and do
not process corresponding ARP requests.
This is a sane default but renders a huge address space
practically unuseable.
The RFC states that no address within the 127/8 block should
ever appear on any network anywhere but it does not forbid
the use of such addresses outside of the loopback device in
particular. For example to address a pool of virtual guests
behind a load balancer.
This patch adds a new interface option 'route_localnet'
enabling routing of the 127/8 address block and processing
of ARP requests on a specific interface.
Note that for the feature to work, the default local route
covering 127/8 dev lo needs to be removed.
Example:
$ sysctl -w net.ipv4.conf.eth0.route_localnet=1
$ ip route del 127.0.0.0/8 dev lo table local
$ ip addr add 127.1.0.1/16 dev eth0
$ ip route flush cache
V2: Fix invalid check to auto flush cache (thanks davem)
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current debugging style and enable dynamic_debug.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using an ascii path to register_net_sysctl as opposed to the slightly
awkward ctl_path allows for much simpler code.
We no longer need to malloc dev_name to keep it alive the length of our
sysctl register instead we can use a small temporary buffer on the
stack.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
The following patch aimed to resolve an issue where secondary, tertiary,
etc. addresses added to bond interfaces could overwrite the
bond->master_ip and vlan_ip values.
commit 917fbdb32f
Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
Date: Wed Nov 23 23:37:15 2011 +0000
bonding: only use primary address for ARP
That patch was good because it prevented bonds using ARP monitoring from
sending frames with an invalid source IP address. Unfortunately, it
didn't always work as expected.
When using an ioctl (like ifconfig does) to set the IP address and
netmask, 2 separate ioctls are actually called to set the IP and netmask
if the mask chosen doesn't match the standard mask for that class of
address. The first ioctl did not have a mask that matched the one in
the primary address and would still cause the device address to be
overwritten. The second ioctl that was called to set the mask would
then detect as secondary and ignored, but the damage was already done.
This was not an issue when using an application that used netlink
sockets as the setting of IP and netmask came down at once. The
inconsistent behavior between those two interfaces was something that
needed to be resolved.
While I was thinking about how I wanted to resolve this, Ralf Zeidler
came with a patch that resolved this on a RHEL kernel by keeping a full
shadow of the entries in dev->ifa_list for the bonding device and vlan
devices in the bonding driver. I didn't like the duplication of the
list as I want to see the 'bonding' struct and code shrink rather than
grow, but liked the general idea.
As the Subject indicates this patch drops the master_ip and vlan_ip
elements from the 'bonding' and 'vlan_entry' structs, respectively.
This can be done because a device's address-list is now traversed to
determine the optimal source IP address for ARP requests and for checks
to see if the bonding device has a particular IP address. This code
could have all be contained inside the bonding driver, but it made more
sense to me to EXPORT and call inet_confirm_addr since it did exactly
what was needed.
I tested this and a backported patch and everything works as expected.
Ralf also helped with verification of the backported patch.
Thanks to Ralf for all his help on this.
v2: Whitespace and organizational changes based on suggestions from Jay
Vosburgh and Dave Miller.
v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's
suggestion.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Ralf Zeidler <ralf.zeidler@nsn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a9b3cd7f32 (rcu: convert uses of rcu_assign_pointer(x, NULL) to
RCU_INIT_POINTER) did a lot of incorrect changes, since it did a
complete conversion of rcu_assign_pointer(x, y) to RCU_INIT_POINTER(x,
y).
We miss needed barriers, even on x86, when y is not NULL.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After reset ipv4_devconf->data[IPV4_DEVCONF_ACCEPT_LOCAL] to 0,
we should flush route cache, or it will continue receive packets with local
source address, which should be dropped.
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When assigning a NULL value to an RCU protected pointer, no barrier
is needed. The rcu_assign_pointer, used to handle that but will soon
change to not handle the special case.
Convert all rcu_assign_pointer of NULL value.
//smpl
@@ expression P; @@
- rcu_assign_pointer(P, NULL)
+ RCU_INIT_POINTER(P, NULL)
// </smpl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a device event generates gratuitous ARP messages, only primary
address is used for sending. This patch iterates through the whole
list. Tested with 2 IP addresses configuration on bonding interface.
Signed-off-by: Zoltan Kiss <schaman@sch.bme.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit e67f88dd12 (net: dont hold rtnl mutex during netlink dump
callbacks) switched rtnl protection to RCU, but we forgot to adjust two
rcu_dereference() lockdep annotations :
inet_get_link_af_size() or inet_fill_link_af() might be called with
rcu_read_lock or rtnl held, so use rcu_dereference_rtnl()
instead of rtnl_dereference()
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ctl_table_headers registered with register_net_sysctl_table should
have been unregistered with the equivalent unregister_net_sysctl_table
Signed-off-by: Lucian Adrian Grijincu <lucian.grijincu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9435eb1cf0
("ipv4: Implement __ip_dev_find using new interface address hash.")
we reimplemented __ip_dev_find() so that it doesn't have to
do a full FIB table lookup.
Instead, it consults a hash table of addresses configured to
interfaces.
This works identically to the old code in all except one case,
and that is for loopback subnets.
The old code would match the loopback device for any IP address
that falls within a subnet configured to the loopback device.
Handle this corner case by doing the FIB lookup.
We could implement this via inet_addr_onlink() but:
1) Someone could configure many addresses to loopback and
inet_addr_onlink() is a simple list traversal.
2) We know the old code works.
Reported-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize the calling of fib_add_ifaddr for all
secondary addresses after the promoted one to start from
their place, not from the new place of the promoted
secondary. It will save some CPU cycles because we
are sure the promoted secondary was first for the subnet
and all next secondaries do not change their place.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
The secondary address promotion relies on fib_sync_down_addr
to remove all routes created for the secondary addresses when
the old primary address is deleted. It does not happen for cases
when the primary address is also in another subnet. Fix that
by deleting local and broadcast routes for all secondaries while
they are on device list and by faking that all addresses from
this subnet are to be deleted. It relies on fib_del_ifaddr being
able to ignore the IPs from the concerned subnet while checking
for duplication.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In usual cases ifa_address == ifa_local, but in the case where
SIOCSIFDSTADDR sets the destination address on a point-to-point
link, ifa_address gets set to that destination address.
Therefore we should use ifa_local when we want the local interface
address.
There were two cases where the selection was done incorrectly:
1) When devinet_ioctl() does matching, it checks ifa_address even
though gifconf correct reported ifa_local to the user
2) IN_DEV_ARP_NOTIFY handling sends a gratuitous ARP using
ifa_address instead of ifa_local.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_NOTIFY_PEER is an explicit request by the driver to send a link
notification while NETDEV_UP/NETDEV_CHANGEADDR generate link
notifications as a sort of side effect.
In the later cases the sysctl option is present because link
notification events can have undesired effects e.g. if the link is
flapping. I don't think this applies in the case of an explicit
request from a driver.
This patch makes NETDEV_NOTIFY_PEER unconditional, if preferred we
could add a new sysctl for this case which defaults to on.
This change causes Xen post-migration ARP notifications (which cause
switches to relearn their MAC tables etc) to be sent by default.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
commits 9f0f7272 (ipv4: AF_INET link address family) and cf7afbfeb8
(rtnl: make link af-specific updates atomic) used incorrect
__in_dev_get_rcu() in RTNL protected contexts, triggering PROVE_RCU
warnings.
Switch to __in_dev_get_rtnl(), wich is more appropriate, since we hold
RTNL.
Based on a report and initial patch from Amerigo Wang.
Reported-by: Amerigo Wang <amwang@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Thomas Graf <tgraf@infradead.org>
Reviewed-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David pointed out correctly, updates to af-specific attributes
are currently not atomic. If multiple changes are requested and
one of them fails, previous updates may have been applied already
leaving the link behind in a undefined state.
This patch splits the function parse_link_af() into two functions
validate_link_af() and set_link_at(). validate_link_af() is placed
to validate_linkmsg() check for errors as early as possible before
any changes to the link have been made. set_link_af() is called to
commit the changes later.
This method is not fail proof, while it is currently sufficient
to make set_link_af() inerrable and thus 100% atomic, the
validation function method will not be able to detect all error
scenarios in the future, there will likely always be errors
depending on states which are f.e. not protected by rtnl_mutex
and thus may change between validation and setting.
Also, instead of silently ignoring unknown address families and
config blocks for address families which did not register a set
function the errors EAFNOSUPPORT respectively EOPNOSUPPORT are
returned to avoid comitting 4 out of 5 update requests without
notifying the user.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the AF_INET link address family exposing the per
device configuration settings via netlink using the attribute
IFLA_INET_CONF.
The format of IFLA_INET_CONF differs depending on the direction
the attribute is sent. The attribute sent by the kernel consists
of a u32 array, basically a 1:1 copy of in_device->cnf.data[].
The attribute expected by the kernel must consist of a sequence
of nested u32 attributes, each representing a change request,
e.g.
[IFLA_INET_CONF] = {
[IPV4_DEVCONF_FORWARDING] = 1,
[IPV4_DEVCONF_NOXFRM] = 0,
}
libnl userspace API documentation and example available from:
http://www.infradead.org/~tgr/libnl/doc-git/group__link__inet.html
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert inetdev_by_index() to not increment in_dev refcount.
Callers hold RCU or RTNL, and should not decrement in_dev refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->ip_ptr is protected by rtnl and rcu.
Yet some places dont use appropriate primitives and/or locking rules.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently such notifications are only generated when the device comes up or the
address changes. However one use case for these notifications is to enable
faster network recovery after a virtual machine migration (by causing switches
to relearn their MAC tables). A migration appears to the network stack as a
temporary loss of carrier and therefore does not trigger either of the current
conditions. Rather than adding carrier up as a trigger (which can cause issues
when interfaces a flapping) simply add an interface which the driver can use
to explicitly trigger the notification.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
When a dump is interrupted at the last device in a hash chain and
then continued, "idx" won't get incremented past s_idx, so s_ip_idx
is not reset when moving on to the next device. This means of all
following devices only the last n - s_ip_idx addresses are dumped.
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Since generally there could be more netdevices changing type other
than bonding, making this event type name "bonding-unrelated"
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuck. It turns out that when we restart sysctls we were restarting
with the values already changed. Which unfortunately meant that
the second time through we thought there was no change and skipped
all kinds of work, despite the fact that there was indeed a change.
I have fixed this the simplest way possible by restoring the changed
values when we restart the sysctl write.
One of my coworkers spotted this bug when after disabling forwarding
on an interface pings were still forwarded.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop computing the number of neighbour table settings we have by
counting the number of binary sysctls. This behaviour was silly
and meant that we could not add another neighbour table setting
without also adding another binary sysctl.
Don't pass the binary sysctl path for neighour table entries
into neigh_sysctl_register. These parameters are no longer
used and so are just dead code.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop using the binary sysctl enumeartion in sysctl.h as an index into
a per interface array. This leads to unnecessary binary sysctl number
allocation, and a fragility in data structure and implementation
because of unnecessary coupling.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to be used together with switch technologies, like RFC3069,
that where the individual ports are not allowed to communicate with
each other, but they are allowed to talk to the upstream router. As
described in RFC 3069, it is possible to allow these hosts to
communicate through the upstream router by proxy_arp'ing.
This patch basically allow proxy arp replies back to the same
interface (from which the ARP request/solicitation was received).
Tunable per device via proc "proxy_arp_pvlan":
/proc/sys/net/ipv4/conf/*/proxy_arp_pvlan
This switch technology is known by different vendor names:
- In RFC 3069 it is called VLAN Aggregation.
- Cisco and Allied Telesyn call it Private VLAN.
- Hewlett-Packard call it Source-Port filtering or port-isolation.
- Ericsson call it MAC-Forced Forwarding (RFC Draft).
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
when using policy routing and the skb mark:
there are cases where a back path validation requires us
to use a different routing table for src ip validation than
the one used for mapping ingress dst ip.
One such a case is transparent proxying where we pretend to be
the destination system and therefore the local table
is used for incoming packets but possibly a main table would
be used on outbound.
Make the default behavior to allow the above and if users
need to turn on the symmetry via sysctl src_valid_mark
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
commit 8ec1e0ebe26087bfc5c0394ada5feb5758014fc8
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:16:35 2009 +0100
ipv4: add sysctl to accept packets with local source addresses
Change fib_validate_source() to accept packets with a local source address when
the "accept_local" sysctl is set for the incoming inet device. Combined with the
previous patches, this allows to communicate between multiple local interfaces
over the wire.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generated with the following semantic patch
@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)
@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)
applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger a écrit :
> On Thu, 12 Nov 2009 15:11:36 +0100
> Eric Dumazet <eric.dumazet@gmail.com> wrote:
>
>> When handling large number of netdevices, inet_dump_ifaddr()
>> is very slow because it has O(N^2) complexity.
>>
>> Instead of scanning one single list, we can use the NETDEV_HASHENTRIES
>> sub lists of the dev_index hash table, and RCU lookups.
>>
>> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
>
> You might be able to make RCU critical section smaller by moving
> it into loop.
>
Indeed. But we dump at most one skb (<= 8192 bytes ?), so rcu_read_lock
holding time is small, unless we meet many netdevices without
addresses. I wonder if its really common...
Thanks
[PATCH net-next-2.6] ipv4: speedup inet_dump_ifaddr()
When handling large number of netdevices, inet_dump_ifaddr()
is very slow because it has O(N2) complexity.
Instead of scanning one single list, we can use the NETDEV_HASHENTRIES
sub lists of the dev_index hash table, and RCU lookups.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that sys_sysctl is a compatiblity wrapper around /proc/sys
all sysctl strategy routines, and all ctl_name and strategy
entries in the sysctl tables are unused, and can be
revmoed.
In addition neigh_sysctl_register has been modified to no longer
take a strategy argument and it's callers have been modified not
to pass one.
Cc: "David Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
As pointed by Stephen Rothwell, commit c6d14c84 added a warning :
net/ipv4/devinet.c: In function 'inet_select_addr':
net/ipv4/devinet.c:902: warning: label 'out' defined but not used
delete unused 'out' label and do some cleanups as well
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds RCU management to the list of netdevices.
Convert some for_each_netdev() users to RCU version, if
it can avoid read_lock-ing dev_base_lock
Ie:
read_lock(&dev_base_loack);
for_each_netdev(net, dev)
some_action();
read_unlock(&dev_base_lock);
becomes :
rcu_read_lock();
for_each_netdev_rcu(net, dev)
some_action();
rcu_read_unlock();
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_get_by_index_rcu() instead of __dev_get_by_index() and
dev_base_lock rwlock
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug with arp_notify.
If arp_notify is enabled, kernel will crash if address is changed
and no IP address is assigned.
http://bugzilla.kernel.org/show_bug.cgi?id=14330
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes commit e36b9d16c6. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:
*. It assumes tha the device is UP when calling dev_close(), or otherwise
dev_close() has no affect. It is worth to mention that initscripts (Redhat)
and sysconfig (Suse) doesn't act the same in this matter.
*. dev_close() has other side affects, like deleting entries from the routing
table, which might be unnecessary.
The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctls are unregistered with the rntl_lock held making
it unsafe to unconditionally grab the the rtnl_lock. Instead
we need to call rtnl_trylock and restart the system call
if we can not grab it. Otherwise we could deadlock at unregistration
time.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return value of nlmsg_notify() as follows:
If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.
This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.
This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds another inet device option to enable gratuitous ARP
when device is brought up or address change. This is handy for
clusters or virtualization.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
call_rcu() will unconditionally rewrite RCU head anyway.
Applies to
struct neigh_parms
struct neigh_table
struct net
struct cipso_v4_doi
struct in_ifaddr
struct in_device
rt->u.dst
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
name and nlen parameters passed to ->strategy hook are unused, remove
them. In general ->strategy hook should know what it's doing, and don't
do something tricky for which, say, pointer to original userspace array
may be needed (name).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net> [ networking bits ]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
