If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.
Use hardware_lock only for error response in this case.
Path1
CPU0 CPU1
---- ----
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0
Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
After a Qlogic card breaks when initializing (test case), the system can
crash in qla2xxx_eh_abort if processing anything but a scsi command type
srb.
Fixes: 1535aa75a3 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-By: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Recent printk changes for KERN_CONT cause this logging to be defectively
emitted on multiple lines. Fix it.
Also reduces object size a trivial amount.
$ size drivers/scsi/qla2xxx/qla_dbg.o*
text data bss dec hex filename
39125 0 0 39125 98d5 drivers/scsi/qla2xxx/qla_dbg.o.new
39164 0 0 39164 98fc drivers/scsi/qla2xxx/qla_dbg.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did. The new stuff is basically lpfc
(nvme), qedi and aacraid. The fixes cover a lot of previously
submitted stuff, the most important of which probably covers some of
the failing irq vectors allocation and other fallout from having the
SCSI command allocated as part of the block allocation functions.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=e+6v
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did.
The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
cover a lot of previously submitted stuff, the most important of which
probably covers some of the failing irq vectors allocation and other
fallout from having the SCSI command allocated as part of the block
allocation functions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
scsi: qedi: Fix memory leak in tmf response processing.
scsi: aacraid: remove redundant zero check on ret
scsi: lpfc: use proper format string for dma_addr_t
scsi: lpfc: use div_u64 for 64-bit division
scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
scsi: cciss: correct check map error.
scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
scsi: aacraid: Fixed expander hotplug for SMART family
scsi: mpt3sas: switch to pci_alloc_irq_vectors
scsi: qedf: fixup compilation warning about atomic_t usage
scsi: remove scsi_execute_req_flags
scsi: merge __scsi_execute into scsi_execute
scsi: simplify scsi_execute_req_flags
scsi: make the sense header argument to scsi_test_unit_ready mandatory
scsi: sd: improve TUR handling in sd_check_events
scsi: always zero sshdr in scsi_normalize_sense
scsi: scsi_dh_emc: return success in clariion_std_inquiry()
scsi: fix memory leak of sdpk on when gd fails to allocate
scsi: sd: make sd_devt_release() static
scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- enable dual mode (initiator + target) qla2xxx operation. (Quinn +
Himanshu)
- add a framework for qla2xxx async fabric discovery. (Quinn +
Himanshu)
- enable iscsi PDU DDP completion offload in cxgbit/T6 NICs. (Varun)
- fix target-core handling of aborted failed commands. (Bart)
- fix a long standing target-core issue NULL pointer dereference with
active I/O LUN shutdown. (Rob Millner + Bryant + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
target: Add counters for ABORT_TASK success + failure
iscsi-target: Fix early login failure statistics misses
target: Fix NULL dereference during LUN lookup + active I/O shutdown
target: Delete tmr from list before processing
target: Fix handling of aborted failed commands
uapi: fix linux/target_core_user.h userspace compilation errors
target: export protocol identifier
qla2xxx: Fix a warning reported by the "smatch" static checker
target/iscsi: Fix unsolicited data seq_end_offset calculation
target/cxgbit: add T6 iSCSI DDP completion feature
target/cxgbit: Enable DDP for T6 only if data sequence and pdu are in order
target/cxgbit: Use T6 specific macros to get ETH/IP hdr len
target/cxgbit: use cxgb4_tp_smt_idx() to get smt idx
target/iscsi: split iscsit_check_dataout_hdr()
target: Remove command flag CMD_T_DEV_ACTIVE
target: Remove command flag CMD_T_BUSY
target: Move session check from target_put_sess_cmd() into target_release_cmd_kref()
target: Inline transport_cmd_check_stop()
target: Remove an overly chatty debug message
target: Stop execution if CMD_T_STOP has been set
...
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial fix to spelling mistake in pr_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For target mode, we need to increase minimum vectors value by one to
account for ATIO queue.
Following stack trace will be seen
Call Trace:
qla24xx_config_rings+0x15a/0x230 [qla2xxx]
qla2x00_init_rings+0x1a1/0x3a0 [qla2xxx]
qla2x00_restart_isp+0x5c/0x120 [qla2xxx]
qla2x00_abort_isp+0x138/0x430 [qla2xxx]
? __schedule+0x260/0x580
qla2x00_do_dpc+0x3bc/0x920 [qla2xxx]
? qla2x00_relogin+0x290/0x290 [qla2xxx]
? schedule+0x3a/0xa0
? qla2x00_relogin+0x290/0x290 [qla2xxx]
kthread+0x103/0x140
? __kthread_init_worker+0x40/0x40
ret_from_fork+0x29/0x40
RIP: qlt_24xx_config_rings+0x6c/0x90
[mkp: fixed Fixes: hash]
Cc: <stable@vger.kernel.org>
Fixes: 17e5fc5858 ("scsi: qla2xxx: fix MSI-X vector affinity")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch cleaned up queue configuration code, such that once
initialized, we should not touch msix_count value. This will prevent
incorrect numbers of MSI-X vectors requested while performing target
mode configuration.
[mkp: fixed Fixes: hash]
Cc: <stable@vger.kernel.org>
Fixes: d74595278f ("scsi: qla2xxx: Add multiple queue pair functionality.")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ). There's also an assortment of minor fixes and the
major update of switching a bunch of drivers to pci_alloc_irq_vectors
from Christoph.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cBQx
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ...).
There's also an assortment of minor fixes and the major update of
switching a bunch of drivers to pci_alloc_irq_vectors from Christoph"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (188 commits)
scsi: megaraid_sas: handle dma_addr_t right on 32-bit
scsi: megaraid_sas: array overflow in megasas_dump_frame()
scsi: snic: switch to pci_irq_alloc_vectors
scsi: megaraid_sas: driver version upgrade
scsi: megaraid_sas: Change RAID_1_10_RMW_CMDS to RAID_1_PEER_CMDS and set value to 2
scsi: megaraid_sas: Indentation and smatch warning fixes
scsi: megaraid_sas: Cleanup VD_EXT_DEBUG and SPAN_DEBUG related debug prints
scsi: megaraid_sas: Increase internal command pool
scsi: megaraid_sas: Use synchronize_irq to wait for IRQs to complete
scsi: megaraid_sas: Bail out the driver load if ld_list_query fails
scsi: megaraid_sas: Change build_mpt_mfi_pass_thru to return void
scsi: megaraid_sas: During OCR, if get_ctrl_info fails do not continue with OCR
scsi: megaraid_sas: Do not set fp_possible if TM capable for non-RW syspdIO, change fp_possible to bool
scsi: megaraid_sas: Remove unused pd_index from megasas_build_ld_nonrw_fusion
scsi: megaraid_sas: megasas_return_cmd does not memset IO frame to zero
scsi: megaraid_sas: max_fw_cmds are decremented twice, remove duplicate
scsi: megaraid_sas: update can_queue only if the new value is less
scsi: megaraid_sas: Change max_cmd from u32 to u16 in all functions
scsi: megaraid_sas: set pd_after_lb from MR_BuildRaidContext and initialize pDevHandle to MR_DEVHANDLE_INVALID
scsi: megaraid_sas: latest controller OCR capability from FW before sending shutdown DCMD
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z7AL
-----END PGP SIGNATURE-----
Merge tag 'for-4.11/linus-merge-signed' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
- blk-mq scheduling framework from me and Omar, with a port of the
deadline scheduler for this framework. A port of BFQ from Paolo is in
the works, and should be ready for 4.12.
- Various fixups and improvements to the above scheduling framework
from Omar, Paolo, Bart, me, others.
- Cleanup of the exported sysfs blk-mq data into debugfs, from Omar.
This allows us to export more information that helps debug hangs or
performance issues, without cluttering or abusing the sysfs API.
- Fixes for the sbitmap code, the scalable bitmap code that was
migrated from blk-mq, from Omar.
- Removal of the BLOCK_PC support in struct request, and refactoring of
carrying SCSI payloads in the block layer. This cleans up the code
nicely, and enables us to kill the SCSI specific parts of struct
request, shrinking it down nicely. From Christoph mainly, with help
from Hannes.
- Support for ranged discard requests and discard merging, also from
Christoph.
- Support for OPAL in the block layer, and for NVMe as well. Mainly
from Scott Bauer, with fixes/updates from various others folks.
- Error code fixup for gdrom from Christophe.
- cciss pci irq allocation cleanup from Christoph.
- Making the cdrom device operations read only, from Kees Cook.
- Fixes for duplicate bdi registrations and bdi/queue life time
problems from Jan and Dan.
- Set of fixes and updates for lightnvm, from Matias and Javier.
- A few fixes for nbd from Josef, using idr to name devices and a
workqueue deadlock fix on receive. Also marks Josef as the current
maintainer of nbd.
- Fix from Josef, overwriting queue settings when the number of
hardware queues is updated for a blk-mq device.
- NVMe fix from Keith, ensuring that we don't repeatedly mark and IO
aborted, if we didn't end up aborting it.
- SG gap merging fix from Ming Lei for block.
- Loop fix also from Ming, fixing a race and crash between setting loop
status and IO.
- Two block race fixes from Tahsin, fixing request list iteration and
fixing a race between device registration and udev device add
notifiations.
- Double free fix from cgroup writeback, from Tejun.
- Another double free fix in blkcg, from Hou Tao.
- Partition overflow fix for EFI from Alden Tondettar.
* tag 'for-4.11/linus-merge-signed' of git://git.kernel.dk/linux-block: (156 commits)
nvme: Check for Security send/recv support before issuing commands.
block/sed-opal: allocate struct opal_dev dynamically
block/sed-opal: tone down not supported warnings
block: don't defer flushes on blk-mq + scheduling
blk-mq-sched: ask scheduler for work, if we failed dispatching leftovers
blk-mq: don't special case flush inserts for blk-mq-sched
blk-mq-sched: don't add flushes to the head of requeue queue
blk-mq: have blk_mq_dispatch_rq_list() return if we queued IO or not
block: do not allow updates through sysfs until registration completes
lightnvm: set default lun range when no luns are specified
lightnvm: fix off-by-one error on target initialization
Maintainers: Modify SED list from nvme to block
Move stack parameters for sed_ioctl to prevent oversized stack with CONFIG_KASAN
uapi: sed-opal fix IOW for activate lsp to use correct struct
cdrom: Make device operations read-only
elevator: fix loading wrong elevator type for blk-mq devices
cciss: switch to pci_irq_alloc_vectors
block/loop: fix race between I/O and set_status
blk-mq-sched: don't hold queue_lock when calling exit_icq
block: set make_request_fn manually in blk_mq_update_nr_hw_queues
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement wraparound-safe refcount_t and kref_t types based on
generic atomic primitives (Peter Zijlstra)
- Improve and fix the ww_mutex code (Nicolai Hähnle)
- Add self-tests to the ww_mutex code (Chris Wilson)
- Optimize percpu-rwsems with the 'rcuwait' mechanism (Davidlohr
Bueso)
- Micro-optimize the current-task logic all around the core kernel
(Davidlohr Bueso)
- Tidy up after recent optimizations: remove stale code and APIs,
clean up the code (Waiman Long)
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
fork: Fix task_struct alignment
locking/spinlock/debug: Remove spinlock lockup detection code
lockdep: Fix incorrect condition to print bug msgs for MAX_LOCKDEP_CHAIN_HLOCKS
lkdtm: Convert to refcount_t testing
kref: Implement 'struct kref' using refcount_t
refcount_t: Introduce a special purpose refcount type
sched/wake_q: Clarify queue reinit comment
sched/wait, rcuwait: Fix typo in comment
locking/mutex: Fix lockdep_assert_held() fail
locking/rtmutex: Flip unlikely() branch to likely() in __rt_mutex_slowlock()
locking/rwsem: Reinit wake_q after use
locking/rwsem: Remove unnecessary atomic_long_t casts
jump_labels: Move header guard #endif down where it belongs
locking/atomic, kref: Implement kref_put_lock()
locking/ww_mutex: Turn off __must_check for now
locking/atomic, kref: Avoid more abuse
locking/atomic, kref: Use kref_get_unless_zero() more
locking/atomic, kref: Kill kref_sub()
locking/atomic, kref: Add kref_read()
locking/atomic, kref: Add KREF_INIT()
...
Fix the following warning reported by the "smatch" static checker:
drivers/scsi/qla2xxx/qla_init.c:3910 qla2x00_alloc_fcport()
warn: use 'flags' here instead of GFP_XXX?
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Six fairly small fixes. None is a real show stopper, two automation
detected problems: one memory leak, one use after free and four others
each of which fixes something that has been a significant source of
annoyance to someone.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJYnqwjAAoJEAVr7HOZEZN4floP+wUavaYK0V+6B81H87UmgTv5
9VEVor+ZKa4ZVkpm+dTRNbPnzXLdfDWAA0RKwCNixNz5zEIHkU0FCU3//2oO7Yv4
jRFyaLfqtT45vdkslOJlrS/XJ+EbYkyeoaHbY5PEgKXh5dVT/jP0jQqn+S7LQHzs
PkAmou2J1/1bs83auFR3V8JDkkBmFIIp/owzWjbuU14BLHDnZbLamI8M6iHRFw4i
ZMizmeGJpn/N0HoQpm1czVIAGIYUj+HVPCARDwZj5KVTapVMbYZx1Vmgq9aTlylZ
U7DDz+j5fm+JkQ8oLhDhpIABfiw4T1YiEw8ysPSEkARWM3KBxNJPfo4qY7eCDayt
L8+nBFr3fgaFMnmlQi6tyOJh7Uu7qQbczAlo5Lqx28vd1zHNCvHkt4463ESJcmuI
a7Ja76wvgt8MvnZ4ThcczpjInlPfb9X1SttadmY/tJ44BKOXoMdw0WPmAhJf1o2r
GDRDBJNJSTEd8Yv5SSJqHq5uCpbjxBPiLCf2FwlFraBK1Iw0UdHXtb/YhzCVWJ29
qnBDKO8ehBPRLzTLwmBzYFGqaBOLMNl47R+cZcEz2yG3YeBIszijO610AHfmuGf7
aSKd7IYNTZTi8rynPnvjn3mN/kAN/oDTBglS4/IGQ3RshM72kRLeW+dJcs1F6Zg0
a3C7q7nDq+zcW1Er++0T
=5Fct
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fairly small fixes. None is a real show stopper, two automation
detected problems: one memory leak, one use after free and four others
each of which fixes something that has been a significant source of
annoyance to someone"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send
scsi: aacraid: Fix INTx/MSI-x issue with older controllers
scsi: mpt3sas: disable ASPM for MPI2 controllers
scsi: mpt3sas: Force request partial completion alignment
scsi: qla2xxx: Avoid that issuing a LIP triggers a kernel crash
scsi: qla2xxx: Fix a recently introduced memory leak
This patch does not change any functionality but avoids that sparse
complains about using variable-length arrays.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch simplifies SRB structure usage in driver.
- Simplify sp->done() and sp->free() interfaces.
- Remove sp->fcport->vha to use vha pointer from sp.
- Use sp->vha context in qla2x00_rel_sp().
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Current code blindly does State Change Registration when
the link is up. Move SCR behind fabric scan, so that arbitrated
loop scan would not get erroneous error message.
Some of the other improvements are as follows
- Add session deletion for TPRLO and send acknowledgment for TPRLO.
- Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ.
- Save NPort ID early in link init.
- Move ABTS & RIDA to ATIOQ helps in keeping command ordering and
link up sequence ordering.
- Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped.
- fcport alloc does the initializes memory to zero. Remove memset to
zero since It might corrupt link list.
- Turn off Registration for State Change MB in loop mode.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With support for dual mode in the driver, this mode becomes
dead code. Remove reverse_ini_mode from code.
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add switch to allow both Initiator Mode & Target
mode to operate at the same time.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently code performs a full scan of the fabric for
every RSCN. Its an expensive process in a noisy large SAN.
This patch optimizes expensive fabric discovery process by
scanning switch for the affected port when RSCN is received.
Currently Initiator Mode code makes login/logout decision without
knowledge of target mode. This causes driver and firmware to go
out-of-sync. This framework synchronizes both initiator mode
personality and target mode personality in making login/logout
decision.
This patch adds following capabilities in the driver
- Send Notification Acknowledgement asynchronously.
- Update session/fcport state asynchronously.
- Create a session or fcport struct asynchronously.
- Send GNL asynchronously. The command will ask FW to
provide a list of FC Port entries FW knows about.
- Send GPDB asynchronously. The command will ask FW to
provide detail data of an FC Port FW knows about or
perform ADISC to verify the state of the session.
- Send GPNID asynchronously. The command will ask switch
to provide WWPN for provided NPort ID.
- Send GPSC asynchronously. The command will ask switch
to provide registered port speed for provided WWPN.
- Send GIDPN asynchronously. The command will ask the
switch to provide Nport ID for provided WWPN.
- In driver unload path, schedule all session for deletion
and wait for deletion to complete before allowing driver
unload to proceed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Current code merges qla_tgt_sess and fc_port structure
into single fc_port structure representing same I-T nexus.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling of patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Updated code with d_id from s_id for better readability and
clarity.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: fixed spelling of patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Callback for sp->done expects scsi_qla_host is passed in as argument,
Instead qla_hw_data is passed in.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
During initial implementation, tape support was included but not
enabled by default on target. So far, we don't see any target
customer requesting this support. Since this code is not being
used actively, we want to remove it and we will add back if there
are any request in future for SRR support.
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Trace flags are useful during debugging crash dumps
using crash utility. These trace flags makes it easier
to understand various states a command has successfully
completed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead define the timeout behavior purely based on the host_template
eh_timed_out method and wire up the existing transport implementations
in the host templates. This also clears up the confusion that the
transport template method overrides the host template one, so some
drivers have to re-override the transport template one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
qla2x00_probe_one() allocates IRQs before it initializes rsp_q_map so
IRQs must be freed even if rsp_q_map allocation did not occur. This was
detected by kmemleak.
Fixes: 4fa1834559 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Michael Hernandez <michael.hernandez@cavium.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-By: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull SCSI target fixes from Bart Van Assche:
- two small fixes for the ibmvscsis driver
- ten patches with bug fixes for the target mode of the qla2xxx driver
- four patches that avoid that the "sparse" and "smatch" static
analyzer tools report false positives for the qla2xxx code base
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
qla2xxx: Disable out-of-order processing by default in firmware
qla2xxx: Fix erroneous invalid handle message
qla2xxx: Reduce exess wait during chip reset
qla2xxx: Terminate exchange if corrupted
qla2xxx: Fix crash due to null pointer access
qla2xxx: Collect additional information to debug fw dump
qla2xxx: Reset reserved field in firmware options to 0
qla2xxx: Set tcm_qla2xxx version to automatically track qla2xxx version
qla2xxx: Include ATIO queue in firmware dump when in target mode
qla2xxx: Fix wrong IOCB type assumption
qla2xxx: Avoid that building with W=1 triggers complaints about set-but-not-used variables
qla2xxx: Move two arrays from header files to .c files
qla2xxx: Declare an array with file scope static
qla2xxx: Fix indentation
ibmvscsis: Fix sleeping in interrupt context
ibmvscsis: Fix max transfer length
Out of order(OOO) processing requires initiator, switch
and target to support OOO. In today's environment, none
of the switches support OOO. OOO requires extra buffer
space which affect performance. By turning ON this feature
in QLogic's FW, it delays error recovery because dropped
frame is treated as out of order frame. We're turning OFF
this option of speed up error recovery.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Termination of Immediate Notify IOCB was using wrong
IOCB handle. IOCB completion code was unable to find
appropriate code path due to wrong handle.
Following message is seen in the logs.
"Error entry - invalid handle/queue (ffff)."
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed word order in patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Soft reset and Risc reset should take 100uS to complete.
This change pad the timeout up to 400uS, which should be
plenty.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Corrupted ATIO is defined as length of fcp_header & fcp_cmd
payload is less than 0x38. It's the minimum size for a frame to
carry 8..16 bytes SCSI CDB. The exchange will be dropped or
terminated if corrupted.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
During code inspection, while investigating following stack trace
seen on one of the test setup, we found out there was possibility
of memory leak becuase driver was not unwinding the stack properly.
This issue has not been reproduced in a test environment or on a
customer setup.
Here's stack trace that was seen.
[1469877.797315] Call Trace:
[1469877.799940] [<ffffffffa03ab6e9>] qla2x00_mem_alloc+0xb09/0x10c0 [qla2xxx]
[1469877.806980] [<ffffffffa03ac50a>] qla2x00_probe_one+0x86a/0x1b50 [qla2xxx]
[1469877.814013] [<ffffffff813b6d01>] ? __pm_runtime_resume+0x51/0xa0
[1469877.820265] [<ffffffff8157c1f5>] ? _raw_spin_lock_irqsave+0x25/0x90
[1469877.826776] [<ffffffff8157cd2d>] ? _raw_spin_unlock_irqrestore+0x6d/0x80
[1469877.833720] [<ffffffff810741d1>] ? preempt_count_sub+0xb1/0x100
[1469877.839885] [<ffffffff8157cd0c>] ? _raw_spin_unlock_irqrestore+0x4c/0x80
[1469877.846830] [<ffffffff81319b9c>] local_pci_probe+0x4c/0xb0
[1469877.852562] [<ffffffff810741d1>] ? preempt_count_sub+0xb1/0x100
[1469877.858727] [<ffffffff81319c89>] pci_call_probe+0x89/0xb0
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
During NVRAM initialization in target mode, reset reserved
fields in firmware options to Zero (BIT 15)
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Include ATIO queue for ISP27XX when firmware dump is collected
for target mode.
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
qlt_reset is called with Immedidate Notify IOCB only.
Current code wrongly cast it as ATIO IOCB.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Remove two set-but-not-used variables and avoid that the compiler
warns about a third variable (rc).
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
This patch avoids that building with W=1 triggers compiler
warnings similar to the following:
drivers/scsi/qla2xxx/qla_nx2.h:538:23: warning: ‘qla8044_reg_tbl’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
This patch avoids that building with W=1 triggers a compiler warning
about a missing declaration.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Since we need to change the implementation, stop exposing internals.
Provide kref_read() to read the current reference count; typically
used for debug messages.
Kills two anti-patterns:
atomic_read(&kref->refcount)
kref->refcount.counter
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that qla2xxx uses the IRQ layer affinity assignment, affinity won't
change over the life time of a device and the notifiers are useless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The first two or three vectors in qla2xxx adapter are global and not
associated with a specific queue. They should not have IRQ affinity
assigned.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the vendor_indentifer and hba_indentifer fields to correct
spelling.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 093df73771 ("scsi: qla2xxx: Fix Target mode handling with
Multiqueue changes.") introduces two bodies of code that look similar
but with s/req/rsp/ in the second instance. But in one case, it looks
like this conversion was missed.
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Quinn Tran <Quinn.Tran@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
msix_entries and qla82xx_msix_entries arrays are never modified in
drivers/scsi/qla2xxx/qla_isr.c. Move their contents to read-only data.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla24xx_enable_msix() calls scnprintf() with a non-literal format
string. This makes clang report -Wformat-security warnings when
compiling this function:
drivers/scsi/qla2xxx/qla_isr.c:3083:7: error: format string is not a
string literal (potentially insecure) [-Werror,-Wformat-security]
msix_entries[i].name);
^~~~~~~~~~~~~~~~~~~~
drivers/scsi/qla2xxx/qla_isr.c:3083:7: note: treat the string as an
argument to avoid this
msix_entries[i].name);
^
"%s",
drivers/scsi/qla2xxx/qla_isr.c:3119:7: error: format string is not a
string literal (potentially insecure) [-Werror,-Wformat-security]
msix_entries[QLA_ATIO_VECTOR].name);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qla2xxx/qla_isr.c:3119:7: note: treat the string as an
argument to avoid this
msix_entries[QLA_ATIO_VECTOR].name);
^
"%s",
Even though msix_entries[...].name are initialized as literal strings
with no % character and are never modified, introduce a "%s" format
parameter in order to silence this -Wformat-security warning and make
clang able to detect at compile time real bugs related to string
formatting.
[mkp: typo]
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a race condition with qla2xxx optrom functions where one thread
might modify optrom buffer, optrom_state while other thread is still
reading from it.
In couple of crashes, it was found that we had successfully passed the
following 'if' check where we confirm optrom_state to be
QLA_SREADING. But by the time we acquired mutex lock to proceed with
memory_read_from_buffer function, some other thread/process had already
modified that option rom buffer and optrom_state from QLA_SREADING to
QLA_SWAITING. Then we got ha->optrom_buffer 0x0 and crashed the system:
if (ha->optrom_state != QLA_SREADING)
return 0;
mutex_lock(&ha->optrom_mutex);
rval = memory_read_from_buffer(buf, count, &off, ha->optrom_buffer,
ha->optrom_region_size);
mutex_unlock(&ha->optrom_mutex);
With current optrom function we get following crash due to a race
condition:
[ 1479.466679] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1479.466707] IP: [<ffffffff81326756>] memcpy+0x6/0x110
[...]
[ 1479.473673] Call Trace:
[ 1479.474296] [<ffffffff81225cbc>] ? memory_read_from_buffer+0x3c/0x60
[ 1479.474941] [<ffffffffa01574dc>] qla2x00_sysfs_read_optrom+0x9c/0xc0 [qla2xxx]
[ 1479.475571] [<ffffffff8127e76b>] read+0xdb/0x1f0
[ 1479.476206] [<ffffffff811fdf9e>] vfs_read+0x9e/0x170
[ 1479.476839] [<ffffffff811feb6f>] SyS_read+0x7f/0xe0
[ 1479.477466] [<ffffffff816964c9>] system_call_fastpath+0x16/0x1b
Below patch modifies qla2x00_sysfs_read_optrom,
qla2x00_sysfs_write_optrom functions to get the mutex_lock before
checking ha->optrom_state to avoid similar crashes.
The patch was applied and tested and same crashes were no longer
observed again.
Tested-by: Milan P. Gandhi <mgandhi@redhat.com>
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly stuff which missed the initial pull. There's a new
driver: qedi, some ufs, ibmvscsis and ncr5380 updates plus some
assorted driver fixes and also a fix for the bug where if a device
goes into a blocked state between configuration and sysfs device add
(which can be a long time under async probing) it would become
permanently blocked.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Zofc
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull late SCSI updates from James Bottomley:
"This is mostly stuff which missed the initial pull.
There's a new driver: qedi, and some ufs, ibmvscsis and ncr5380
updates plus some assorted driver fixes and also a fix for the bug
where if a device goes into a blocked state between configuration and
sysfs device add (which can be a long time under async probing) it
would become permanently blocked"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (30 commits)
scsi: avoid a permanent stop of the scsi device's request queue
scsi: mpt3sas: Recognize and act on iopriority info
scsi: qla2xxx: Fix Target mode handling with Multiqueue changes.
scsi: qla2xxx: Add Block Multi Queue functionality.
scsi: qla2xxx: Add multiple queue pair functionality.
scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls.
scsi: qla2xxx: Only allow operational MBX to proceed during RESET.
scsi: hpsa: remove memory allocate failure message
scsi: Update 3ware driver email addresses
scsi: zfcp: fix rport unblock race with LUN recovery
scsi: zfcp: do not trace pure benign residual HBA responses at default level
scsi: zfcp: fix use-after-"free" in FC ingress path after TMF
scsi: libcxgbi: return error if interface is not up
scsi: cxgb4i: libcxgbi: add missing module_put()
scsi: cxgb4i: libcxgbi: cxgb4: add T6 iSCSI completion feature
scsi: cxgb4i: libcxgbi: add active open cmd for T6 adapters
scsi: cxgb4i: use cxgb4_tp_smt_idx() to get smt_idx
scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.
scsi: aacraid: remove wildcard for series 9 controllers
scsi: ibmvscsi: add write memory barrier to CRQ processing
...
Pull scsi target cleanups from Bart Van Assche:
"The changes here are:
- a few small bug fixes for the iSCSI and user space target drivers.
- minimize the target build time by about 30% by rearranging #include
directives
- fix the second argument passed to percpu_ida_alloc()
- reduce the number of false positive warnings reported by sparse
These patches pass Wu Fengguang's build bot tests and also the
linux-next tests"
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
iscsi-target: Return error if unable to add network portal
target: Fix spelling mistake and unwrap multi-line text
target/iscsi: Fix double free in lio_target_tiqn_addtpg()
target/user: Fix use-after-free of tcmu_cmds if they are expired
target: Minimize #include directives
target/user: Add an #include directive
cxgbit: Add an #include directive
ibmvscsi_tgt: Add two #include directives
sbp-target: Add an #include directive
qla2xxx: Add an #include directive
configfs: Minimize #include directives
usb: gadget: Fix second argument of percpu_ida_alloc()
sbp-target: Fix second argument of percpu_ida_alloc()
target/user: Fix a data type in tcmu_queue_cmd()
target: Use NULL instead of 0 to represent a pointer
- Fix race condition between dpc_thread accessing Multiqueue resources
and qla2x00_remove_one thread trying to free resource.
- Fix out of order free for Multiqueue resources. Also, Multiqueue
interrupts needs a workqueue. Interrupt needed to stop before
the wq can be destroyed.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tell the SCSI layer how many hardware queues we have based on the number
of max queue pairs created. The number of max queue pairs created will
depend on number of MSI-X vector count.
This feature can be turned on via CONFIG_SCSI_MQ_DEFAULT or passing
scsi_mod.use_blk_mq=Y as a parameter to the kernel
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced existing multiple queue functionality with framework
that allows for the creation of pairs of request and response queues,
either at start of day or dynamically.
Queue pair creation depend on module parameter "ql2xmqsupport",
which need to be enabled to create queue pair.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaces the old pci_enable_msi[x]* and pci_disable_msi[x] calls.
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is allowing only ROM mailbox command which are
necessary to initialize chip after a reset has been issued.
In a target environment, there could be a user space daemon
which can issue statistics and other management mailbox command
which are non-critical. This patch will timeout non critical
mailbox commands immediately rather than waiting for timeout,
if driver detects that chip reset has been issued or chip reset
is in progress.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
The following statement in qla_isr.c needs the size of struct
t10_pi_tuple:
spt += j;
Hence include the <linux/t10-pi.h> header file.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
fc_bsg_jobdone() and bsg_job_done() are 1:1 copies now so use the
bsg-lib one instead of the FC private implementation.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change FC drivers to use 'struct bsg_job' from bsg-lib.h instead of
'struct fc_bsg_job' from scsi_transport_fc.h and remove 'struct
fc_bsg_job'.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide fc_bsg_to_rport() helper that will become handy when we're
moving from struct fc_bsg_job to a plain struct bsg_job. Also move all
LLDDs to use the new helper.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide fc_bsg_to_shost() helper that will become handy when we're
moving from struct fc_bsg_job to a plain struct bsg_job. Also use this
little helper in the LLDDs.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export fc_bsg_jobdone so drivers can use it directly instead of doing
the round-trip via struct fc_bsg_job::job_done() and use it in the
LLDDs. That way we can also unify the interfaces of fc_bsg_jobdone and
bsg_job_done.
As we've converted all LLDDs over to use fc_bsg_jobdone() directly, we
can remove the function pointer from struct fc_bsg_job as well.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't use fc_bsg_job::request and fc_bsg_job::reply directly, but use
helper variables bsg_request and bsg_reply. This will be helpful when
transitioning to bsg-lib.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The previous commit 1535aa75a3 ("qla2xxx: fix invalid DMA access after
command aborts in PCI device remove") introduced a regression during an
EEH recovery, since the change to the qla2x00_abort_all_cmds() function
calls qla2xxx_eh_abort(), which verifies the EEH recovery condition but
handles it heavy-handed. (commit a465537ad1 "qla2xxx: Disable the
adapter and skip error recovery in case of register disconnect.")
This problem warrants a more general/optimistic solution right into
qla2xxx_eh_abort() (eg in case a real command abort arrives during EEH
recovery, or if it takes long enough to trigger command aborts); but
it's still worth to add a check to ensure the code added by the previous
commit is correct and contained within its owner function.
This commit just adds a 'if (!ha->flags.eeh_busy)' check around it.
(ahem; a trivial fix for this -rc series; sorry for this oversight.)
With it applied, both PCI device remove and EEH recovery works fine.
Fixes: 1535aa75a3 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a command is aborted in the kernel but not in the adapter, it might be
considered complete and its DMA memory released, but it is still alive in
the adapter, which will trigger an invalid DMA access upon its completion
(in the DMA operations to deliver the command response to the driver).
On powerpc platforms with IOMMU/EEH capabilities, the problem is observed
during PCI device removal with ongoing IO requests -- which might trigger
an EEH event very often, pointing to a 'TCE Request Page Access Error'.
In that path, which is qla2x00_remove_one(), the commands are aborted in
qla2x00_abort_all_cmds(), which does not perform an abort in the adapter
as is done in qla2xxx_eh_abort() for example.
So, this patch changes qla2x00_abort_all_cmds() to abort commands in the
adapter too, with a call to qla2xxx_eh_abort(), which already implements
all the logic to submit abort requests and handle responses.
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the driver is unloading, in qla2x00_remove_one(), there is a single
call/point in time to abort ongoing commands, qla2x00_abort_all_cmds(),
which is still several steps away from the call to scsi_remove_host().
If more commands continue to arrive and be processed during that
interval, when the driver is tearing down and releasing its structures,
it might potentially hit an oops due to invalid memory access:
Unable to handle kernel paging request for data at address 0x00000138
<...>
NIP [d000000004700a40] qla2xxx_queuecommand+0x80/0x3f0 [qla2xxx]
LR [d000000004700a10] qla2xxx_queuecommand+0x50/0x3f0 [qla2xxx]
So, fail commands in qla2xxx_queuecommand() if the UNLOADING bit is set.
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A system can get hung task timeouts if a qlogic board fails during
initialization (if the board breaks again or fails the init). The hang
involves the scsi scan.
In a nutshell, since commit beb9e315e6 ("qla2xxx: Prevent removal and
board_disable race"):
...it is possible to have freed ha (base_vha->hw) early by a call to
qla2x00_remove_one when pdev->enable_cnt equals zero:
if (!atomic_read(&pdev->enable_cnt)) {
scsi_host_put(base_vha->host);
kfree(ha);
pci_set_drvdata(pdev, NULL);
return;
Almost always, the scsi_host_put above frees the vha structure
(attached to the end of the Scsi_Host we're putting) since it's the last
put, and life is good. However, if we are entering this routine because
the adapter has broken sometime during initialization AND a scsi scan is
already in progress (and has done its own scsi_host_get), vha will not
be freed. What's worse, the scsi scan will access the freed ha structure
through qla2xxx_scan_finished:
if (time > vha->hw->loop_reset_delay * HZ)
return 1;
The scsi scan keeps checking to see if a scan is complete by calling
qla2xxx_scan_finished. There is a timeout value that limits the length
of time a scan can take (hw->loop_reset_delay, usually set to 5
seconds), but this definition is in the data structure (hw) that can get
freed early.
This can yield unpredictable results, the worst of which is that the
scsi scan can hang indefinitely. This happens when the freed structure
gets reused and loop_reset_delay gets overwritten with garbage, which
the scan obliviously uses as its timeout value.
The fix for this is simple: at the top of qla2xxx_scan_finished, check
for the UNLOADING bit in the vha structure (_vha is not freed at this
point). If UNLOADING is set, we exit the scan for this adapter
immediately. After this last reference to the ha structure, we'll exit
the scan for this adapter, and continue on.
This problem is hard to hit, but I have run into it doing negative
testing many times now (with a test specifically designed to bring it
out), so I can verify that this fix works. My testing has been against a
RHEL7 driver variant, but the bug and patch are equally relevant to to
the upstream driver.
Fixes: beb9e315e6 ("qla2xxx: Prevent removal and board_disable race")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of defining a local version of it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistakes in ql_dbg messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "if (test_bit(UNLOADING..." line was indented one tab more than it
should have been. There was an extra parenthesis around the
qla2x00_reset_active() function call. I lined up the conditions a bit
so that it shows how they group together.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: 969a619 ("qla2xxx: Add support for buffer to buffer credit value for ISP27XX.")
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If there is error recovery going on due to command timeout and
there is register disconnect, then disable the adapter.
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During hot swap of PCI device, there can be PCI error on device,
during normal driver unload. The race between normal driver unload and
driver unload due to PCI error, can lead to system crash.Fix is to check
if there is unload going on and allow that function to unload the driver.
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Properly initialize IO statistics to avoid initial 0xFFFFFFF (-1) values.
Cleanup/simplify usage of pointer to statistics structure.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When VP decoupling enabled, there could be a window where, FLOGI from initiators
can be dropped before VP0 is enabled, causing link level recovery.
Retry FLOGI to avoid link level recovery.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2xxx first calls request_irq() and then does the setup of the queue
entry data needed in the interrupt handlers in when using MSI-X. This
could lead to a NULL pointer dereference when an IRQ fires between the
request_irq() call and the assignment of the qentry data structure to
the rsp->msix field. A possible case for such a race would be in the
kdump case when the HBA's IRQs are still enabled but the driver is
undergoing a new initialisation and thus is not aware of already
activated IRQs in the HBA.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
That macros uses logical "&&" instead of bit-wise "&" which is
apparently wrong. Since the macro is completely unused, simply
remove it, so that nobody can accidentially use it anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target pending updates for v4.7-rc1.
The highlights this round include:
- Allow external PR/ALUA metadata path be defined at runtime via top
level configfs attribute (Lee)
- Fix target session shutdown bug for ib_srpt multi-channel (hch)
- Make TFO close_session() and shutdown_session() optional (hch)
- Drop se_sess->sess_kref + convert tcm_qla2xxx to internal kref
(hch)
- Add tcm_qla2xxx endpoint attribute for basic FC jammer (Laurence)
- Refactor iscsi-target RX/TX PDU encode/decode into common code
(Varun)
- Extend iscsit_transport with xmit_pdu, release_cmd, get_rx_pdu,
validate_parameters, and get_r2t_ttt for generic ISO offload
(Varun)
- Initial merge of cxgb iscsi-segment offload target driver (Varun)
The bulk of the changes are Chelsio's new driver, along with a number
of iscsi-target common code improvements made by Varun + Co along the
way"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (29 commits)
iscsi-target: Fix early sk_data_ready LOGIN_FLAGS_READY race
cxgbit: Use type ISCSI_CXGBIT + cxgbit tpg_np attribute
iscsi-target: Convert transport drivers to signal rdma_shutdown
iscsi-target: Make iscsi_tpg_np driver show/store use generic code
tcm_qla2xxx Add SCSI command jammer/discard capability
iscsi-target: graceful disconnect on invalid mapping to iovec
target: need_to_release is always false, remove redundant check and kfree
target: remove sess_kref and ->shutdown_session
iscsi-target: remove usage of ->shutdown_session
tcm_qla2xxx: introduce a private sess_kref
target: make close_session optional
target: make ->shutdown_session optional
target: remove acl_stop
target: consolidate and fix session shutdown
cxgbit: add files for cxgbit.ko
iscsi-target: export symbols
iscsi-target: call complete on conn_logout_comp
iscsi-target: clear tx_thread_active
iscsi-target: add new offload transport type
iscsi-target: use conn_transport->transport_type in text rsp
...
This patch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas) there's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJXO8W0AAoJEDeqqVYsXL0MW24H/jGWwfjsDUiSsLwbLca6DWu8
ZCWZ7rSZ27CApwGPgZGpLvUg+vpW8Ykm2zdeBnlZ6ScXS+dT3uo/PHsnemsTextj
6glQNIOFY0Ja2GwkkN00M6IZQhTJ628cqJKIEJxC68lIw16wiOwjZaK68GMrusDO
Sl062rkuLR6Jb2T+YoT/sD8jQfWlSj2V9e9rqJoS/rIbS6B+hUipuybz2yQ2yK2u
XFc30yal9oVz1fHEoh2O8aqckW3/iskukVXVuZ0MQzT/lV/bm9I6AnWVHw7d0Yhp
ZELjXpjx5M2Z/d8k0Wvx1e25oL/ERwa96yLnTvRcqyF5Yt1EgAhT+jKvo4pnGr8=
=L6y/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"First round of SCSI updates for the 4.6+ merge window.
This batch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas). There's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (138 commits)
mpt3sas: Used "synchronize_irq()"API to synchronize timed-out IO & TMs
mpt3sas: Set maximum transfer length per IO to 4MB for VDs
mpt3sas: Updating mpt3sas driver version to 13.100.00.00
mpt3sas: Fix initial Reference tag field for 4K PI drives.
mpt3sas: Handle active cable exception event
mpt3sas: Update MPI header to 2.00.42
Revert "lpfc: Delete unnecessary checks before the function call mempool_destroy"
eata_pio: missing break statement
hpsa: Fix type ZBC conditional checks
scsi_lib: Decode T10 vendor IDs
scsi_dh_alua: do not fail for unknown VPD identification
scsi_debug: use locally assigned naa
scsi_debug: uuid for lu name
scsi_debug: vpd and mode page work
scsi_debug: add multiple queue support
bfa: fix bfa_fcb_itnim_alloc() error handling
megaraid_sas: Downgrade two success messages to info
cxlflash: Fix to resolve dead-lock during EEH recovery
scsi_debug: rework resp_report_luns
scsi_debug: use pdt constants
...
This patch introduces support for TCM_QLA2XXX_DEBUG and
associated tcm_qla2xxx_tpg->tpg_attrib.jam_host checking
used to test dropped packets to FC host environments.
Tested by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This stops abusing the common sess_kref to overload it for private
usage, which allows removing the shutdown_session method as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
struct register_host_info stores a 64-bit UTC system time timestamp.
This patch removes the use of 'struct timeval' to obtain that timestamp
as its tv_sec value will overflow on 32-bit systems in year 2038 beyond.
The patch uses ktime_get_real_seconds() which returns a 64-bit seconds value.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the Linux kernel it is preferred to return a meaningful error code
instead of -1. This patch does not change the behavior of the caller of
qla82xx_pinit_from_rom().
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only new stuff which missed the first pull request is an update to
the UFS driver. The rest is an assortment of bug fixes and minor
tweaks which appeared recently (some are fixes for recent code and
some are stuff spotted recently by the checkers or the new gcc-6
compiler [most of Arnd's stuff]).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJW9nPcAAoJEDeqqVYsXL0M4CIH/1EkSjCyLzm5yDGzPKyD8LuS
r8mNmXEgKxKuCVenmsydDEa4YmEH/94ysMevwXCogDvUz0ms/qRHJnF3cy7MT7fe
TlcuKQdshl3k5gRP33K3AkK1aNtzyWGwiP+5+e+uO3rzJgujJa+IcpvYYk/e46GE
yTfi6uEdNRFD6xGxqfttvO9I+YKj5XtRpNZQe/YAS6bcyLm0R62031b8OcmKxWYT
m/F9AlxKeIDmutH5GK5siePQ1KNmn1LZOGYO8RKA4jcyzhxJ8qv8HdRpFGAGuyg/
f7V0OGqhLGlzZ5pNRfsYpAhoScmwbm+rYJv1W0vjRdeoAgmNkR8S5LDeXHpvZ5A=
=2sEy
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"The only new stuff which missed the first pull request is an update to
the UFS driver.
The rest is an assortment of bug fixes and minor tweaks which appeared
recently (some are fixes for recent code and some are stuff spotted
recently by the checkers or the new gcc-6 compiler [most of Arnd's
stuff])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi_common: do not clobber fixed sense information
scsi: ufs: select CONFIG_NLS
scsi: fc: use get/put_unaligned64 for wwn access
fnic: move printk()s outside of the critical code section.
qla2xxx: avoid maybe_uninitialized warning
megaraid_sas: add missing curly braces in ioctl handler
lpfc: fix misleading indentation
scsi_transport_sas: add 'scsi_target_id' sysfs attribute
scsi_dh_alua: uninitialized variable in alua_check_vpd()
scsi: ufs-qcom: add printouts of testbus debug registers
scsi: ufs-qcom: enable/disable the device ref clock
scsi: ufs-qcom: set PA_Local_TX_LCC_Enable before link startup
scsi: ufs: add device quirk delay before putting UFS rails in LPM
scsi: ufs: fix leakage during link off state
scsi: ufs: tune UniPro parameters to optimize hibern8 exit time
scsi: ufs: handle non spec compliant bkops behaviour by device
scsi: ufs: add retry for query descriptors
scsi: ufs: add error recovery after DL NAC error
scsi: ufs: make error handling bit faster
scsi: ufs: disable vccq if it's not needed by UFS device
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add target_alloc_session() w/ callback helper for doing se_session
allocation + tag + se_node_acl lookup. (HCH + nab)
- Tree-wide fabric driver conversion to use target_alloc_session()
- Convert sbp-target to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Chris Boot + nab)
- Convert usb-gadget to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Andrzej Pietrasiewicz + nab)
- Convert xen-scsiback to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Juergen Gross + nab)
- Convert tcm_fc to use TARGET_SCF_ACK_KREF I/O + TMR krefs
- Convert ib_srpt to use percpu_ida tag pre-allocation
- Add DebugFS node for qla2xxx target sess list (Quinn)
- Rework iser-target connection termination (Jenny + Sagi)
- Convert iser-target to new CQ API (HCH)
- Add pass-through WRITE_SAME support for IBLOCK (Mike Christie)
- Introduce data_bitmap for asynchronous access of data area (Sheng
Yang + Andy)
- Fix target_release_cmd_kref shutdown comp leak (Himanshu Madhani)
Also, there is a separate PULL request coming for cxgb4 NIC driver
prerequisites for supporting hw iscsi segmentation offload (ISO), that
will be the base for a number of v4.7 developments involving
iscsi-target hw offloads"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
target: Fix target_release_cmd_kref shutdown comp leak
target: Avoid DataIN transfers for non-GOOD SAM status
target/user: Report capability of handling out-of-order completions to userspace
target/user: Fix size_t format-spec build warning
target/user: Don't free expired command when time out
target/user: Introduce data_bitmap, replace data_length/data_head/data_tail
target/user: Free data ring in unified function
target/user: Use iovec[] to describe continuous area
target: Remove enum transport_lunflags_table
target/iblock: pass WRITE_SAME to device if possible
iser-target: Kill the ->isert_cmd back pointer in struct iser_tx_desc
iser-target: Kill struct isert_rdma_wr
iser-target: Convert to new CQ API
iser-target: Split and properly type the login buffer
iser-target: Remove ISER_RECV_DATA_SEG_LEN
iser-target: Remove impossible condition from isert_wait_conn
iser-target: Remove redundant wait in release_conn
iser-target: Rework connection termination
iser-target: Separate flows for np listeners and connections cma events
iser-target: Add new state ISER_CONN_BOUND to isert_conn
...
The qlt_check_reserve_free_req() function produces an incorrect warning
when CONFIG_PROFILE_ANNOTATED_BRANCHES is set:
drivers/scsi/qla2xxx/qla_target.c: In function 'qlt_check_reserve_free_req':
drivers/scsi/qla2xxx/qla_target.c:1887:3: error: 'cnt_in' may be used uninitialized in this function [-Werror=maybe-uninitialized]
ql_dbg(ql_dbg_io, vha, 0x305a,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"qla_target(%d): There is no room in the request ring: vha->req->ring_index=%d, vha->req->cnt=%d, req_cnt=%d Req-out=%d Req-in=%d Req-Length=%d\n",
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
vha->vp_idx, vha->req->ring_index,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
vha->req->cnt, req_cnt, cnt, cnt_in, vha->req->length);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qla2xxx/qla_target.c:1887:3: error: 'cnt' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem is that gcc fails to track the state of the condition across
an annotated branch.
This slightly rearranges the code to move the second if() block
into the first one, to avoid the warning while retaining the
behavior of the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-By: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch converts existing qla2xxx target mode assignment
of struct qla_tgt_sess related sid + loop_id values to use
a callback via the new target_alloc_session API caller.
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we fail to queue an srb for an async login we should set the
relogin flag so it will be retried as the reason for the queuing
failure was most likely transient. Failure to do this can lead to
failed paths as login is never retried if the relogin flag is not
set.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set bit 12 of additional firmware options 3 to let firmware
hold status IOCB until ABTS response is received from Target.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function value inside se_cmd can change if the TMR is cancelled.
Use original ATIO Type to correctly determine CTIO response.
Signed-off-by: Swapnil Nagle <swapnil.nagle@purestroage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ Upstream Commit 84e32a06f4 ]
Commit 84e32a0 ("qla2xxx: Use pci_enable_msix_range() instead of
pci_enable_msix()") introduced a regression when target mode is enabled.
In qla24xx_enable_msix(), ha->max_rsp_queues was incorrectly set
to a value higher than the number of response queues allocated causing
an invalid dereference. Specifically here in qla2x00_init_rings():
*rsp->in_ptr = 0;
Add additional check to make sure the pointer is valid. following
call stack will be seen
---- 8< ----
RIP: 0010:[<ffffffffa02ccadc>] [<ffffffffa02ccadc>] qla2x00_init_rings+0xdc/0x320 [qla2xxx]
RSP: 0018:ffff880429447dd8 EFLAGS: 00010082
....
Call Trace:
[<ffffffffa02ceb40>] qla2x00_abort_isp+0x170/0x6b0 [qla2xxx]
[<ffffffffa02c6f77>] qla2x00_do_dpc+0x357/0x7f0 [qla2xxx]
[<ffffffffa02c6c20>] ? qla2x00_relogin+0x260/0x260 [qla2xxx]
[<ffffffff8107d2c9>] kthread+0xc9/0xe0
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
[<ffffffff8172cc6f>] ret_from_fork+0x3f/0x70
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
---- 8< ----
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
During lun reset, TMR thread from TCM would issue abort
to qla driver. At abort time, each command is in different
state. Depending on the state, qla will use the TMR thread
to trigger a command free(cmd_kref--) if command is not
down at firmware.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Introduce configfs support for unlocked configfs_depend_item()
(krzysztof + andrezej)
- Conversion of usb-gadget target driver to new function registration
interface (andrzej + sebastian)
- Enable qla2xxx FC target mode support for Extended Logins (himansu +
giridhar)
- Enable qla2xxx FC target mode support for Exchange Offload (himansu +
giridhar)
- Add qla2xxx FC target mode irq affinity notification + selective
command queuing. (quinn + himanshu)
- Fix iscsi-target deadlock in se_node_acl configfs deletion (sagi +
nab)
- Convert se_node_acl configfs deletion + se_node_acl->queue_depth to
proper se_session->sess_kref + target_get_session() usage. (hch +
sagi + nab)
- Fix long-standing race between se_node_acl->acl_kref get and
get_initiator_node_acl() lookup. (hch + nab)
- Fix target/user block-size handling, and make sure netlink reaches
all network namespaces (sheng + andy)
Note there is an outstanding bug-fix series for remote I_T nexus port
TMR LUN_RESET has been posted and still being tested, and will likely
become post -rc1 material at this point"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (56 commits)
scsi: qla2xxxx: avoid type mismatch in comparison
target/user: Make sure netlink would reach all network namespaces
target: Obtain se_node_acl->acl_kref during get_initiator_node_acl
target: Convert ACL change queue_depth se_session reference usage
iscsi-target: Fix potential dead-lock during node acl delete
ib_srpt: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Wait for command completion before freeing a session
target: Fix a memory leak in target_dev_lba_map_store()
target: Support aborting tasks with a 64-bit tag
usb/gadget: Remove set-but-not-used variables
target: Remove an unused variable
target: Fix indentation in target_core_configfs.c
target/user: Allow user to set block size before enabling device
iser-target: Fix non negative ERR_PTR isert_device_get usage
target/fcoe: Add tag support to tcm_fc
qla2xxx: Check for online flag instead of active reset when transmitting responses
qla2xxx: Set all queues to 4k
qla2xxx: Disable ZIO at start time.
qla2xxx: Move atioq to a different lock to reduce lock contention
...
A recent bug fix added code that does
bool logged_out = (status & 0xFFFF);
if (logged_out == CTIO_PORT_LOGGED_OUT)
...
This looks wrong because we are comparing a boolean with an
integer constant, ang gcc warns about it accordingly:
drivers/scsi/qla2xxx/qla_target.c: In function 'qlt_do_ctio_completion':
drivers/scsi/qla2xxx/qla_target.c:3587:20: warning: comparison of constant '41' with boolean expression is always false [-Wbool-compare]
(logged_out == CTIO_PORT_LOGGED_OUT) ?
The correct fix is presumably to make that variable an 'int'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 71cdc07964 ("qla2xxx: Delete session if initiator is gone from FW")
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Driver has following initialization sequence for Target mode
1. Driver initialization starts
2. ISP Abort is scheduled when the target is enabled.
qla2xxx [0000:04:00.0]-4807:25: ISP abort scheduled
qla2xxx [0000:04:00.0]-00af:25: Performing ISP error recovery - ha=ffff880caa9e0000.
3. DPC thread starts the ISP Abort
4. While DPC is resetting the chip and initializing the firmware, we get
async events from the firmware about P2P mode, LOOP UP and PORT UPDATE.
5. PRLI from a initiator is delivered to us followed by a PLOGI and then a
SCSI command which creates a session.
6. If the SCSI command is a WRITE in this case, we issue XFR RDY and it
gets dropped as can be seen with messages RESET-XFR because ISP Abort
is still active
qla2xxx [0000:04:00.0]-e902:25: RESET-XFR active/old-count/new-count = 1/1/1.
7. If the SCSI command is a READ, we issue RESPONSE and they get dropped
as well because Abort is still active.
qla2xxx [0000:04:00.0]-e901:25: RESET-RSP active/old-count/new-count = 1/1/1
8. Now eventually, ISP Abort finishes clearing the DPC flags.
qla2xxx [0000:04:00.0]-8822:25: qla2x00_abort_isp succeeded.
qla2xxx [0000:04:00.0]-4808:25: ISP abort end.
9. Since we dropped SCSI commands silently (without any responses sent
to the initiator) initiator waits for a SCSI timeout (which is 60
seconds in our case), Sends an ABTS which fails since there
no se_cmd found for the tag that ABTS is referencing as the
commands were cleaned up in Step 6 and 7.
10. Initiator send an IO after the ABTS which succeed fine.
To fix the above case, the following changes have been made:
- To prevent target from dropping commands silently, use the online flag
instead to check for an active chip reset. Once the port is online during
a chip reset phase, we are good to process the commands.
- Clean up qla2x00_restart_isp to not set the online flag and process ATIO
as it is unnecessary. During a chip reset, interrupts are enabled only
after setting the online flag to 1, so ATIO's won't be missed and hence
no need to process ATIO's after setting the online flag.
Signed-off-by: Dilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
set ATIO/Request/Response Queues and Default number
of outstanding command to 4k.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
99% of the time the ATIOQ has SCSI command. The other 1% of time
is something else. Most of the time this interrupt does not need
to hold the hardware_lock. We're moving the ATIO interrupt thread
to a different lock to reduce lock contention.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
queue work element to specific process lessen cache miss
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Sessions management (add, deleted, modify) currently are serialized
through the hardware_lock. Hardware_lock is a high traffic lock.
This lock is accessed by both the transmit & receive sides.
Sessions management is now moved off to another lock call sess_lock.
This is done to reduce lock contention and increase traffic throughput.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Replace QLA_TGT_STATE_ABORTED state with a bit because
the current state of the command is lost when an abort
is requested by upper layer.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Until now ack'ing of a new PLOGI has only been delayed if there
was an existing session for the same WWN. Ack was released when
the session deletion completed.
If there was another WWN session with the same fc_id/loop_id pair
(aka "conflicting session"), PLOGI was still ack'ed immediately.
This potentially caused a problem when old session deletion logged
fc_id/loop_id out of FW after new session has been established.
Two work-arounds were attempted before:
1. Dropping PLOGIs until conflicting session goes away.
2. Detecting initiator being logged out of FW and issuing LOGO
to force re-login.
This patch introduces proper solution to the problem where PLOGI
is held until either existing session with same WWN or any
conflicting session goes away. Mechanism supports one session holding
two PLOGI acks as well as one PLOGI ack being held by many sessions.
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
1. Initiator A is logged in with fc_id(1)/loop_id(1)
2. Initiator A re-logs in with fc_id(2)/loop_id(2)
3. Part of old session deletion async logoout for 1/1 is queued
4. Initiator B logs in with fc_id(1)/loop_id(1), starts
passing data and creates session.
5. Async logo from 3 is processed by DPC and sent to FW
Now initiator B has the session but is logged out from FW.
This condition is detected first with CTIO error 29 at which
point we should delete current session. During session
deletion we will send LOGO to initiator to force re-login.
Under rare circumstances initiator might be logged out of FW,
not have driver session, but still think it's logged in.
E.g. the above sequence plus session deletion due to re-config.
Incoming commands will fail to create local session because
initiator is not found in FW. In this case we also issue LOGO
to initiator to force him re-login.
Finally this patch fixes exchange leak when commands where
received in logged out state. In this case loop_id must be
set to FFFF when corresponding exchange is terminated. The
patch modifies exchange termination to always use FFFF,
since in certain scenarios it's impossible to tell whether
command was received in logged in or logged out state.
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds interface to send explicit LOGO
explicit LOGO using using ELS commands from driver.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
DebugFS now will show fw_resource_count node.
FW Resource count
Original TGT exchg count[0]
current TGT exchg count[0]
original Initiator Exchange count[2048]
Current Initiator Exchange count[2048]
Original IOCB count[2078]
Current IOCB count[2067]
MAX VP count[254]
MAX FCF count[0]
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Following counters are added in target mode to help debugging efforts.
Target Counters
qla_core_sbt_cmd = 0
qla_core_ret_sta_ctio = 0
qla_core_ret_ctio = 0
core_qla_que_buf = 0
core_qla_snd_status = 0
core_qla_free_cmd = 0
num alloc iocb failed = 0
num term exchange sent = 0
num Q full sent = 0
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables Exchange offload support in Qlogic ISP.
To enable exchange offload with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexchoffld to any non-zero number.
This will alow ISP firmware to store exchange data structures
used by firmware to host memory provided by driver. ISP firmware
can supports upto 32k total active exchanges.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables Extended Logins support in Qlogic ISP.
To enable extended login with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexlogins to any non-zero number.
This will alow ISP firmware to store port database structure
information of remote login sessions to host memory provided
by driver. ISP firmware supports upto 16k total logins.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is quite a bumper crop of fixes: Three from Arnd correcting various build
issues in some configurations, a lock recursion in qla2xxx. Two potentially
exploitable issues in hpsa and mvsas, a potential null deref in st, A revert
of a bdi registration fix that turned out to cause even more problems, a set
of fixes to allow people who only defined MPT2SAS to still work after the
mpt2/mpt3sas merger and a couple of fixes for issues turned up by the hyper-v
storvsc driver.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWY8fDAAoJEDeqqVYsXL0MPhwH/Rs05LUU2vnlaZDdDpH5zY56
YQgKh5duF+ZH+Y4NxX5kkLLo05wpE6xD5xp2yzzmnjTA0Uf/yLVHNdb5D6tRZgSo
mZjAX+/wGDb/ErwvwTk/K2mhEvB0iZJJVMyWcG3F9dKgciRCF/p1Gn5EarGmc+vM
w/9xrs1j24Pw7ipHgBj9zU13w+SPMI7LunR0oYL9CJg24jgXG9sAbrwLkox5kHLo
FFBCrZhev1mzFKa1C+Ln3s0iSf0yEQMd4khzPJAUElkw812PZ7I6r4bCP0ZPKDed
JR8zex9jo77RyWZwA7fIathA0/ujv0AeIRXgvzb0/io1Yk577r98vt+S3koQVK8=
=ptgb
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a bumper crop of fixes: three from Arnd correcting
various build issues in some configurations, a lock recursion in
qla2xxx. Two potentially exploitable issues in hpsa and mvsas, a
potential null deref in st, a revert of a bdi registration fix that
turned out to cause even more problems, a set of fixes to allow people
who only defined MPT2SAS to still work after the mpt2/mpt3sas merger
and a couple of fixes for issues turned up by the hyper-v storvsc
driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
Revert "scsi: Fix a bdi reregistration race"
mpt3sas: Add dummy Kconfig option for backwards compatibility
Fix a memory leak in scsi_host_dev_release()
block/sd: Fix device-imposed transfer length limits
scsi_debug: fix prevent_allow+verify regressions
MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem.
sd: Make discard granularity match logical block size when LBPRZ=1
scsi: hpsa: select CONFIG_SCSI_SAS_ATTR
scsi: advansys needs ISA dma api for ISA support
scsi_sysfs: protect against double execution of __scsi_remove_device()
st: fix potential null pointer dereference.
scsi: report 'INQUIRY result too short' once per host
advansys: fix big-endian builds
qla2xxx: Fix rwlock recursion
hpsa: logical vs bitwise AND typo
mvsas: don't allow negative timeouts
mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag
this patch fixes following regression
# targetcli
[Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable'
Fixes: 2eafd72939 ("target: use per-attribute show and store methods")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove firmware binary names for the ISPs, which are not submitted to
linux-firmware.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Reviewed-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sorry for the delay in this patch which was mostly caused by getting the
merger of the mpt2/mpt3sas driver, which was seen as an essential item of
maintenance work to do before the drivers diverge too much. Unfortunately,
this caused a compile failure (detected by linux-next), which then had to be
fixed up and incubated. In addition to the mpt2/3sas rework, there are
updates from pm80xx, lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc
and ufs plus an assortment of changes including some year 2038 issues, a fix
for a remove before detach issue in some drivers and a couple of other minor
issues.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWRnpiAAoJEDeqqVYsXL0MJd0IAIkNP1q/6ksMw/lam2UlbdxN
zFsFOIhGM3xLnBFehbCx7JW3cmybA7WC5jhMjaa1OeJmYHLpwbTzvVwrLs2l/0y1
/S+G0wwxROZfIKj/1EO3oKbSPCu9N3lStxOnmNXt5PSUEzAXrTqSNTtnMf2ZGh7j
bQxTWEJe+66GckgGw4ozTXJHWXqM/Zs/FsYjn2h/WzFhFv8utr7zRSzHMVjcqpLG
TK/Lt03hiTGqiignKrV9W6JzdGTWf2LGIsj/njgR0dxv59cNH8PrHIjZyknSBxgn
lblinsCjxDHWnP4BSfTi9MQG1lEiZiWO3Y6TKkKJTgxZ9M0Eitspc+cLOiJ1mpg=
=HvQf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This also allows to remove the target-specific old configfs macros, and
gets rid of the target_core_fabric_configfs.h header which only had one
function declaration left that could be moved to a better place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target-pending updates for v4.3-rc1.
Mostly bug-fixes and minor changes this round. The fallout from the
big v4.2-rc1 RCU conversion have (thus far) been minimal.
The highlights this round include:
- Move sense handling routines into scsi_common code (Sagi)
- Return ABORTED_COMMAND sense key for PI errors (Sagi)
- Add tpg_enabled_sendtargets attribute for disabled iscsi-target
discovery (David)
- Shrink target struct se_cmd by rearranging fields (Roland)
- Drop iSCSI use of mutex around max_cmd_sn increment (Roland)
- Replace iSCSI __kernel_sockaddr_storage with sockaddr_storage (Andy +
Chris)
- Honor fabric max_data_sg_nents I/O transfer limit (Arun + Himanshu +
nab)
- Fix EXTENDED_COPY >= v4.1 regression OOPsen (Alex + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (37 commits)
target: use stringify.h instead of own definition
target/user: Fix UFLAG_UNKNOWN_OP handling
target: Remove no-op conditional
target/user: Remove unused variable
target: Fix max_cmd_sn increment w/o cmdsn mutex regressions
target: Attach EXTENDED_COPY local I/O descriptors to xcopy_pt_sess
target/qla2xxx: Honor max_data_sg_nents I/O transfer limit
target/iscsi: Replace __kernel_sockaddr_storage with sockaddr_storage
target/iscsi: Replace conn->login_ip with login_sockaddr
target/iscsi: Keep local_ip as the actual sockaddr
target/iscsi: Fix np_ip bracket issue by removing np_ip
target: Drop iSCSI use of mutex around max_cmd_sn increment
qla2xxx: Update tcm_qla2xxx module description to 24xx+
iscsi-target: Add tpg_enabled_sendtargets for disabled discovery
drivers: target: Drop unlikely before IS_ERR(_OR_NULL)
target: check DPO/FUA usage for COMPARE AND WRITE
target: Shrink struct se_cmd by rearranging fields
target: Remove cmd->se_ordered_id (unused except debug log lines)
target: add support for START_STOP_UNIT SCSI opcode
target: improve unsupported opcode message
...
This patch adds an optional fabric driver provided SGL limit
that target-core will honor as it's own internal I/O maximum
transfer length limit, as exposed by EVPD=0xb0 block limits
parameters.
This is required for handling cases when host I/O transfer
length exceeds the requested EVPD block limits maximum
transfer length. The initial user of this logic is qla2xxx,
so that we can avoid having to reject I/Os from some legacy
FC hosts where EVPD=0xb0 parameters are not honored.
When se_cmd payload length exceeds the provided limit in
target_check_max_data_sg_nents() code, se_cmd->data_length +
se_cmd->prot_length are reset with se_cmd->residual_count
plus underflow bit for outgoing TFO response callbacks.
It also checks for existing CDB level underflow + overflow
and recalculates final residual_count as necessary.
Note this patch currently assumes 1:1 mapping of PAGE_SIZE
per struct scatterlist entry.
Reported-by: Craig Watson <craig.watson@vanguard-rugged.com>
Cc: Craig Watson <craig.watson@vanguard-rugged.com>
Tested-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This includes one new driver: cxlflash plus the usual grab bag of updates for
the major drivers: qla2xxx, ipr, storvsc, pm80xx, hptiop, plus a few assorted
fixes.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJV5eGiAAoJEDeqqVYsXL0MCpwH/AoneZOPeCx0YdTlyiojasi4
Kc7ECmV9IJJoMoCbP8grwStvynYyCHDSphYmqopZPRlD021eG8ota2uRTHEGJI+q
SoiZUlq8ti8xgnD55mubwO+UNF+zoELMyHUok2pGzBoZN5alA6nvKuNY7Hif3P3b
YMT490oWQLjWmJkMW8TbpMn9nHpW0dfbP323uaggWsMy3CSI707+x36FLi1/ICg6
MZRyv4aESAcauZGUI5EG+SrIl3OBQX7snsYXyuqD3biGqzbGc3p3L9uWG1qXHDbM
OSGXhN+our0WYHCV1/UrGz7/IAWW1UU0W2qgCBwkXkDjkXJ4jqd36zLJxeuhSpE=
=KOmP
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This includes one new driver: cxlflash plus the usual grab bag of
updates for the major drivers: qla2xxx, ipr, storvsc, pm80xx, hptiop,
plus a few assorted fixes.
There's another tranch coming, but I want to incubate it another few
days in the checkers, plus it includes a mpt2sas separated lifetime
fix, which Avago won't get done testing until Friday"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (85 commits)
aic94xx: set an error code on failure
storvsc: Set the error code correctly in failure conditions
storvsc: Allow write_same when host is windows 10
storvsc: use storage protocol version to determine storage capabilities
storvsc: use correct defaults for values determined by protocol negotiation
storvsc: Untangle the storage protocol negotiation from the vmbus protocol negotiation.
storvsc: Use a single value to track protocol versions
storvsc: Rather than look for sets of specific protocol versions, make decisions based on ranges.
cxlflash: Remove unused variable from queuecommand
cxlflash: shift wrapping bug in afu_link_reset()
cxlflash: off by one bug in cxlflash_show_port_status()
cxlflash: Virtual LUN support
cxlflash: Superpipe support
cxlflash: Base error recovery support
qla2xxx: Update driver version to 8.07.00.26-k
qla2xxx: Add pci device id 0x2261.
qla2xxx: Fix missing device login retries.
qla2xxx: do not clear slot in outstanding cmd array
qla2xxx: Remove decrement of sp reference count in abort handler.
qla2xxx: Add support to show MPI and PEP FW version for ISP27xx.
...
On certain conditions, login failures will just invoke
qla2x00_mark_device_lost() with the intend to do login again;
but if login_retry has been set already, that would fail to set the
relogin needed flag which is required to wakeup the DPC to retry.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fix for memory leak when command is not found by firmware due to
mismatch in sp reference count.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Instead of resetting the adapter wait for the login to timeout
and retry. Resetting the adapter can cause extended path recovery
times.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If an SRB is NULL but the handle is in range just drop the
command instead of also resetting the adapter. If the handle
is in range then the command was valid at some point and may
have been aborted. Resetting the adapter can lead to extended
recovery times in this case.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Aovid crashing the system in the scenario where firmware
just completes the command and it can not find the command
during abort mailbox processing. This scenario can lead to
sp reference counter being zero. Instead of crashing the
system, use WARN_ON to print warning in log file.
Signed-off-by: Hiral Patel <hiral.patel@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Execute qla25xx_manipulate_risc_semaphore() only for
ssdid 0x0175 and 0x0240.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When we get logged out, mark the port lost and set dpc flag for relogin.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Invoking get_cmd_state for qla2xxx always returns 0. Instead change it
to return the actual fabric state from qla_tgt_cmd. This will help with
debugging.
Signed-off-by: Dilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Surround conditional locking statements with "#ifndef __CHECKER__" /
"#endif" to hide these for the sparse static source code analysis
tool.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The "return QLA_SUCCESS" statement just above the "fw_load_failed"
label cannot be reached, hence remove it. Additionally remove the
"else" keyword since the code block below the if-statement ends
with a return statement.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Avoid that smatch reports the following warning:
drivers/scsi/qla2xxx/qla_attr.c:1081: qla2x00_model_desc_show() warn: this array is probably non-NULL. 'vha->hw->model_desc'
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch removes 21 casts between an __iomem pointer type and
another data type but also introduces five new casts (see also
the casts with "__force"). Although this patch does not change
any functionality, IMHO the code with __force casts needs further
review.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Whether htonl() or __constant_htonl() is used, if the argument
is a constant the conversion happens at compile time. Hence leave
out the __constant_ prefix for this and other endianness
conversion functions. This improves source code readability.
[jejb: checkpatch fixes]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Replace the QLA82XX_ADDR_IN_RANGE() and QLA8044_ADDR_IN_RANGE() macros
with the inline function addr_in_range(). This avoids that the compiler
reports the following warning when building with W=1: comparison of
unsigned expression >= 0 is always true.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Detected these variables by building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Let the debug statement in qlafx00_tm_iocb_entry() report both rsp_info
and rsp_info_len instead of reporting rsp_info_len twice.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Commit f3ddac1918 ("[SCSI] qla2xxx:
Disable adapter when we encounter a PCI disconnect.") has introduced a
code that disables the board, releasing some resources, when reading
0xffffffff.
In case this happens when there is an EEH, this read will trigger EEH
detection and set PCI channel offline. EEH will be able to recover the
card from this state by doing a reset, so it's a better option than
simply disabling the card.
Since eeh_check_failure will mark the channel as offline before
returning the read value, in case there really was an EEH, we can simply
check for pci_channel_offline, preventing the board_disable code from
running if it's true.
Without this patch, EEH code will try to access those same resources
that board_disable will try to free. This race can cause EEH recovery to
fail.
[ 504.370577] EEH: Notify device driver to resume
[ 504.370580] qla2xxx [0001:07:00.0]-9002:2: The device failed to resume I/O from slot/link_reset.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Pre 24xx HBAs are not supported by tcm_qla2xxx, so go ahead and
reflect this for informational purposes.
Also fix QLogic spelling.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The newly introduced aborted_task TFO callback has to terminate
exchange with QLogic driver, since command is being deleted and
no status will be queued to the driver at a later point.
This patch also moves the burden of releasing one cmd refcount to
the aborted_task handler.
Changed iSCSI aborted_task logic to satisfy the above requirement.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If a new initiator (different WWN) shows up on the same fcport, old
initiator's session is scheduled for deletion. But there is a small
window between it being marked with QLA_SESS_DELETION_IN_PROGRESS
and qlt_unret_sess getting called when new session's commands will
keep finding old session in the fcport map.
This patch drops cmds/tmrs if they find session in the progress of
being deleted.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are multiple reasons for disabling this:
1. It provides no functional benefit. We pretty much only get a few more
sysfs entries for each port, but all that information is already
available from /sys/kernel/debug/target/qla-session-X
2. It already only works in private-loop mode. By disabling we'll be
getting more uniform behavior with fabric mode.
3. It creates complications for the new PLOGI handling mechanism:
scsi_transport_fc port deletion timer could race with new session
from initiator and cause logout after successful login.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
