This enables the complex mapping for the Gemini and kicks in
custom read/write functions that will wrap the existing
simple functions in calls to enable/disable the parallel
flash pins using pin controls.
This is necessary on some hardware such as the D-Link
DIR-685 where all flash pins are patched in/out at the same
time, but some of the flash pins are in practice unused by
the flash and have anyway been reused as GPIO.
This concerns specifically CE1 on the Gemini. There is only
one flash chip, so only CE0 is used, and the line for CE1
has been reused as chip select for the emulated SPI port
connected to the display. If we try to use the same lines
for flash and GPIO at the same time, one of them will loose:
the GPIO line will disappear because it gets disconnected
from the pin when the flash group is muxed out.
Fix this by introducing two pin control states named simply
"enabled" and "disabled" and only enable the flash lines
when absolutely necessary (during read/write/copy). This
way, they are available for GPIO at all other times and
the display works.
Collect all the state variables in a struct named
struct gemini_flash and allocate this struct at probe
time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Looks like this driver was initially added to support the NOR on the
DA830-EVM (Davinci) board, but the board file update was never merged.
Keeping unused drivers just adds to the maintenance burden, so let's
remove it if nobody uses it.
Cc: David Griego <dgriego@mvista.com>
Cc: Aleksey Makarov <amakarov@ru.mvista.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Savinay Dharmappa <savinay.dharmappa@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Controlling some MSB address lines using GPIOs is just a small
deviation from the generic physmap logic, and merging those two drivers
allows us to share most of the probe logic, which is a good thing.
Also, the gpio-addr-flash driver is unused since the removal of
the blackfin arch in v4.17, so we can safely remove the old driver
without risking breaking existing boards.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that the physmap_of driver is gone, the gemini and versative
extensions are part of the physmap driver. Rename the source files and
the config option to reflect this.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
There's no real reason to have two separate driver for the DT and pdata
case. Just do what we do everywhere else and handle DT and pdata
parsing in the same driver.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Fix indentation and replace '---help---' by 'help' to make things
consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
The blackfin architecture is getting removed, so this driver
has become obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
In order to support device tree probing of Gemini NOR flash
chips, a certain register in the syscon needs to be poked
to enable parallel flash mode.
Such things used to happen in "necessarily different" board
file code, and this indeed was also done for the Gemini, so
the MTD driver could treat it as any memory-mapped NOR flash,
but this is not the way in the future: board files need to
go, and hardware concerns distributed down to the applicable
drivers.
This adds a hook in the same way that the Versatile did: if
the Kconfig symbol is not selected the net total of supporting
Gemini should be zero bytes of added code. To live up to this
promise, also the return value error print from the Versatile
extra probe call get to be removed in this patch, all printing
need to happen in the add-ons.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This reduces the Kconfig for the RealView by assuming we are
always booting from the device tree, and removing all the uses
of CONFIG_REALVIEW_DT and replacing with CONFIG_ARCH_REALVIEW.
Further:
- Drop REALVIEW_HIGH_PHYS_OFFSET: we don't use this with device
tree.
- Drop the REALVIEW_EB_ARM11MP_REVB option: we now handle this
by simply using another device tree.
- Drop the PB1176 secure flash option: this is defined in the
PB1176 device tree but marked as "disabled", so users who
want to use it can simply enable it in the device tree and
go hacking around.
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support device tree probing of Versatile NOR flash
chips, there must be a way to add the VPP (write protection)
enable/disable callback. The register in question is in the
system controllers of these machines. Apart from this quirk,
the ARM flash chips are standard CFI flash chips from various
vendors.
Additionally, the Integrator/AP require you to set up the external
bus interface (EBI) to allow writes to the chip select where the
flash memory is connected.
Solve this by looking for the arm,versatile-flash compatible
string in the flash device tree node. In the driver,
add a special hook to check for the various Versatile syscons and
register a callback for .set_vpp() if this compatible is present.
Provide a special Kconfig entry for the addon hook so it will
not be compiled in if the Versatile boards are not supported.
Stubs in the header file make sure the impact will be zero on
other platforms. (Compilers optimze this out.)
With this patch, a large slew of ARM board file code can be
removed.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
In addition, CONFIG_PPC_8xx also defines CONFIG_CPM1 as
communication co-processor
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
It looks like not many places still have that old CONFIG_8xx used,
so it is likely to be a good time to get rid of it completely ?
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Anyone working with an AMD Elan SC520 development or evaluation board
would be building a dedicated kernel for it, so we can make the
sc520cdp and netsc520 maps depend on MELAN. SC520_CPUFREQ already
depends on MELAN so it makes things more consistent. It also makes
kernel configuration for every other x86 user easier.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Up to now mtd-ram devices described in device trees were only accessible
if mtd-flash or mtd-rom were also configured at linux configuration
time, because MTD_PHYSMAP_OF was only available if (MTD_CFI ||
MTD_JEDECPROBE || MTD_ROM). Allow MTD_PHYSMAP_OF selection also
when only MTD_RAM is set.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no point in displaying the TS5500-specific driver entries if
TS5500 board support itself isn't enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
JEDEC device support was removed in v2.6.22. (It had been marked as
BROKEN (indirectly) since at least v2.6.12.)
When it was removed the two JEDEC mapping drivers that depended on it
should have been removed too. Do so now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch provide migration to using "mtd-ram" driver instead of using
special driver for handling NVRAM memory.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Support partitions larger than 4GiB in device tree
- Support for new SPI chips
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iEYEABECAAYFAlGLxzEACgkQdwG7hYl686M+PgCdHAn3fDzGW7gUL1tj43NCqaC8
PWoAoNAD5YpI3wYEBxped2MjSfgbQMvq
=hM2T
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd
Pull MTD update from David Woodhouse:
- Lots of cleanups from Artem, including deletion of some obsolete
drivers
- Support partitions larger than 4GiB in device tree
- Support for new SPI chips
* tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd: (83 commits)
mtd: omap2: Use module_platform_driver()
mtd: bf5xx_nand: Use module_platform_driver()
mtd: denali_dt: Remove redundant use of of_match_ptr
mtd: denali_dt: Change return value to fix smatch warning
mtd: denali_dt: Use module_platform_driver()
mtd: denali_dt: Fix incorrect error check
mtd: nand: subpage write support for hardware based ECC schemes
mtd: omap2: use msecs_to_jiffies()
mtd: nand_ids: use size macros
mtd: nand_ids: improve LEGACY_ID_NAND macro a bit
mtd: add 4 Toshiba nand chips for the full-id case
mtd: add the support to parse out the full-id nand type
mtd: add new fields to nand_flash_dev{}
mtd: sh_flctl: Use of_match_ptr() macro
mtd: gpio: Use of_match_ptr() macro
mtd: gpio: Use devm_kzalloc()
mtd: davinci_nand: Use of_match_ptr()
mtd: dataflash: Use of_match_ptr() macro
mtd: remove h720x flash support
mtd: onenand: remove OneNAND simulator
...
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The h720x platform support is going away in linux-3.10, so the
MTD driver will also not be needed any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver depends on CONFIG_IXP2000 which is not defined anywhere, which
means this driver is dead.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver is marked as broken for very long time. Most probably this board is
just something ancient no one cares about anyway.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver depends on the CONFIG_TQM8xxL symbol, which is not defined
anywhere, which means that this driver is dead.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver depends on the CONFIG_RPXCLASSIC and CONFIG_RPXLITE symbols, which
are not defined anywhere, and this means that this driver is dead.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-pcmcia@lists.infradead.org
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver depends on CONFIG_MBX which is not defined anywhere, which means
this driver is dead.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-pcmcia@lists.infradead.org
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver depends on the CONFIG_DMV182 symbol which is not defined anywhere,
and this means that this driver is dead.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver depends on the CONFIG_DBOX2 symbol which does not exist in
the kernel, which means the driver is dead.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This allows to put the filesystem at a defined address in ROM allowing
to save more precious RAM.
I think it's safe to default to ROM because the intention of using the
uclinux map is to use a romfs and so mtd-ram doesn't give you anything
that mtd-rom doesn't.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlDSAa4ACgkQdwG7hYl686MMcACeNYa//ghPtccb5L+IRXsqaFDL
Yi4AoLWOaOjN8qM4KUF/bfMEkwNGAePz
=DaAQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
The kernel has never contained the symbol SA1100_FORTUNET so the driver
never compiled and can be removed safely.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch provide migration to using "physmap-flash" and "mtd-ram"
drivers instead of using special driver for handling memory.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
The uclinux.c map driver has traditionally been used only on non-MMU based
systems. But there is no fundamental reason it can't be used on systems
running with virtual memory.
Some ColdFire CPU based systems now have full paged MMU hardware and can use
the uclinux.c mapping driver, so making the uclinux.c driver configuration
depend on !CONFIG_MMU doesn't make sense now. Allow the CONFIG_MTD_UCLINUX
option to be enabled if CONFIG_COLDFIRE is enabled. (I have chosen not to
just more generally allow uclinux.c for any MMU type to keep this option
hidden for most systems that are not interested in setting it).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Because we can have a single kernel to support multiple machines, we
need to make loading specific drivers for the target platform only.
For this, driver is converted to the platform driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The SBC8260 support was dropped back when we moved from ppc to
powerpc. We are now also dropping the support for the EOL SBC8560,
so we can also delete this mapping support, as they were the only
users of it.
Artem: also remove the symbol from the Makefile.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
scb2_flash.c is a PCI driver, but its build fails when CONFIG_PCI
is not enabled, so make it depend on PCI.
drivers/mtd/maps/scb2_flash.c:237:1: warning: data definition has no type or storage class
drivers/mtd/maps/scb2_flash.c:237:1: warning: type defaults to 'int' in declaration of 'module_pci_driver'
drivers/mtd/maps/scb2_flash.c:237:1: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
CONFIG_GENERIC_IO is just enough for the basic MTD stuff.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Recent BCM63XX devices support a variety of flash types (parallel, SPI,
NAND) and share the partition layout. To prevent code duplication make
the CFE partition parsing code a stand alone mtd parser to allow SPI or
NAND flash drivers to use it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The integrator flash has been deleted, even from the Makefile.
Drop the Kconfig entry as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
EDB7312 isn't supported by mainline kernel, this driver wasn't working
before recent fixes, the same functionality can be achieved via physmap,
so drop it now. If the board support will ever be submitted to mainline,
one either can revert this commit, or use physmap mtd map driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
physmap_configure() and physmap_set_partitions() have no users in kernel.
Out of kernel users should have been converted to regular platform device
long ago. Drop support for this obsolete API.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
It's a Ceiva/Polaroid PhotoMax Digital Picture Frame. Support for it was
commited before 2.6.12-rc2, current git contains no functional changes
since it's start. Driver containing MTD support for that board was
broken for some time already.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
Now that none of the drivers use CONFIG_MTD_PARTITIONS we can remove
it from Kconfig and the last remaining uses.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
