Up to now, linear and IMMR mappings are managed via huge TLB entries
through specific code directly in TLB miss handlers. This implies
some patching of the TLB miss handlers at startup, and a lot of
dedicated code.
Remove all this specific dedicated code.
For now we are back to normal handling via standard 4k pages. In the
next patches, linear memory mapping and IMMR mapping will be managed
through huge pages.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/221b7e3ead80a5969629938c023f8cfe45fdd2fb.1589866984.git.christophe.leroy@csgroup.eu
At startup, map 32 Mbytes of memory through 4 pages of 8M,
and PIN them inconditionnaly. They need to be pinned because
KASAN is using page tables early and the TLBs might be
dynamically replaced otherwise.
Remove RSV4I flag after installing mappings unless
CONFIG_PIN_TLB_XXXX is selected.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b27c5767d18053b59f7eefddc189fcc3acf7b9c2.1589866984.git.christophe.leroy@csgroup.eu
Only early debug requires IMMR to be mapped early.
No need to set it up and pin it in assembly. Map it
through page tables at udbg init when necessary.
If CONFIG_PIN_TLB_IMMR is selected, pin it once we
don't need the 32 Mb pinned RAM anymore.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/13c1e8539fdf363d3146f4884e5c3c76c6c308b5.1589866984.git.christophe.leroy@csgroup.eu
Pinned TLBs cannot be modified when the MMU is enabled.
Create a function to rewrite the pinned TLB entries with MMU off.
To set pinned TLB, we have to turn off MMU, disable pinning,
do a TLB flush (Either with tlbie and tlbia) then reprogam
the TLB entries, enable pinning and turn on MMU.
If using tlbie, it cleared entries in both instruction and data
TLB regardless whether pinning is disabled or not.
If using tlbia, it clears all entries of the TLB which has
disabled pinning.
To make it easy, just clear all entries in both TLBs, and
reprogram them.
The function takes two arguments, the top of the memory to
consider and whether data is RO under _sinittext.
When DEBUG_PAGEALLOC is set, the top is the end of kernel rodata.
Otherwise, that's the top of physical RAM.
Everything below _sinittext is set RX, over _sinittext that's RW.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c17806014bb1c06513ad1e1d510faea31984b177.1589866984.git.christophe.leroy@csgroup.eu
At the time being, 512k huge pages are handled through hugepd page
tables. The PMD entry is flagged as a hugepd pointer and it
means that only 512k hugepages can be managed in that 4M block.
However, the hugepd table has the same size as a normal page
table, and 512k entries can therefore be nested with normal pages.
On the 8xx, TLB loading is performed by software and allthough the
page tables are organised to match the L1 and L2 level defined by
the HW, all TLB entries have both L1 and L2 independent entries.
It means that even if two TLB entries are associated with the same
PMD entry, they can be loaded with different values in L1 part.
The L1 entry contains the page size (PS field):
- 00 for 4k and 16 pages
- 01 for 512k pages
- 11 for 8M pages
By adding a flag for hugepages in the PTE (_PAGE_HUGE) and copying it
into the lower bit of PS, we can then manage 512k pages with normal
page tables:
- PMD entry has PS=11 for 8M pages
- PMD entry has PS=00 for other pages.
As a PMD entry covers 4M areas, a PMD will either point to a hugepd
table having a single entry to an 8M page, or the PMD will point to
a standard page table which will have either entries to 4k or 16k or
512k pages. For 512k pages, as the L1 entry will not know it is a
512k page before the PTE is read, there will be 128 entries in the
PTE as if it was 4k pages. But when loading the TLB, it will be
flagged as a 512k page.
Note that we can't use pmd_ptr() in asm/nohash/32/pgtable.h because
it is not defined yet.
In ITLB miss, we keep the possibility to opt it out as when kernel
text is pinned and no user hugepages are used, we can save several
instruction by not using r11.
In DTLB miss, that's just one instruction so it's not worth bothering
with it.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/002819e8e166bf81d24b24782d98de7c40905d8f.1589866984.git.christophe.leroy@csgroup.eu
Prepare ITLB handler to handle _PAGE_HUGE when CONFIG_HUGETLBFS
is enabled. This means that the L1 entry has to be kept in r11
until L2 entry is read, in order to insert _PAGE_HUGE into it.
Also move pgd_offset helpers before pte_update() as they
will be needed there in next patch.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/21fd1de8fba781bededa9474a5a9374aefb1f849.1589866984.git.christophe.leroy@csgroup.eu
CONFIG_8xx_COPYBACK was there to help disabling copyback cache mode
for debuging hardware. But nobody will design new boards with 8xx now.
All 8xx platforms select it, so make it the default and remove
the option.
Also remove the Mx_RESETVAL values which are pretty useless and hide
the real value while reading code.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/bcc968cda075516eb76e2f25e09821f582c566b4.1589866984.git.christophe.leroy@csgroup.eu
Commit 55c8fc3f49 ("powerpc/8xx: reintroduce 16K pages with HW
assistance") redefined pte_t as a struct of 4 pte_basic_t, because
in 16K pages mode there are four identical entries in the page table.
But hugepd entries for 8M pages require only one entry of size
pte_basic_t. So there is no point in creating a cache for 4 entries
page tables.
Calculate PTE_T_ORDER using the size of pte_basic_t instead of pte_t.
Define specific huge_pte helpers (set_huge_pte_at(), huge_pte_clear(),
huge_ptep_set_wrprotect()) to write the pte in a single entry instead
of using set_pte_at() which writes 4 identical entries in 16k pages
mode. Also make sure that __ptep_set_access_flags() properly handle
the huge_pte case.
Define set_pte_filter() inline otherwise GCC doesn't inline it anymore
because it is now used twice, and that gives a pretty suboptimal code
because of pte_t being a struct of 4 entries.
Those functions are also used for 512k pages which only require one
entry as well allthough replicating it four times was harmless as 512k
pages entries are spread every 128 bytes in the table.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/43050d1a0c2d6e1541cab9c1126fc80bc7015ebd.1589866984.git.christophe.leroy@csgroup.eu
pte_update() is a bit special for the 8xx. At the time
being, that's an #ifdef inside the nohash/32 pte_update().
As we are going to make it even more special in the coming
patches, create a dedicated version for pte_update() for 8xx.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a103be0099ac2360f8c44f4a1a63cc03713a1360.1589866984.git.christophe.leroy@csgroup.eu
PPC64 takes 3 additional parameters compared to PPC32:
- mm
- address
- huge
These 3 parameters will be needed in order to perform different
action depending on the page size on the 8xx.
Make pte_update() prototype identical for PPC32 and PPC64.
This allows dropping an #ifdef in huge_ptep_get_and_clear().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/38111acf6841047a8addde37c63e92d611ee38c2.1589866984.git.christophe.leroy@csgroup.eu
On PPC32, __ptep_test_and_clear_young() takes the mm->context.id
In preparation of standardising pte_update() params between PPC32 and
PPC64, __ptep_test_and_clear_young() need mm instead of mm->context.id
Replace context param by mm.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0a65470e50a14373b7c2291184514aa982462255.1589866984.git.christophe.leroy@csgroup.eu
When CONFIG_PTE_64BIT is set, pte_update() operates on
'unsigned long long'
When CONFIG_PTE_64BIT is not set, pte_update() operates on
'unsigned long'
In asm/page.h, we have pte_basic_t which is 'unsigned long long'
when CONFIG_PTE_64BIT is set and 'unsigned long' otherwise.
Refactor pte_update() using pte_basic_t.
While we are at it, drop the comment on 44x which is not applicable
to book3s version of pte_update().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c78912bc8613fb249c3d80aeb1062796b5c49400.1589866984.git.christophe.leroy@csgroup.eu
When CONFIG_PTE_64BIT is set, pte_update() operates on
'unsigned long long'
When CONFIG_PTE_64BIT is not set, pte_update() operates on
'unsigned long'
In asm/page.h, we have pte_basic_t which is 'unsigned long long'
when CONFIG_PTE_64BIT is set and 'unsigned long' otherwise.
Refactor pte_update() using pte_basic_t.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/590d67994a2847cd9fe088f7d974499e3a18b6ac.1589866984.git.christophe.leroy@csgroup.eu
Only 40x still uses PTE_ATOMIC_UPDATES.
40x cannot not select CONFIG_PTE64_BIT.
Drop handling of PTE_ATOMIC_UPDATES:
- In nohash/64
- In nohash/32 for CONFIG_PTE_64BIT
Keep PTE_ATOMIC_UPDATES only for nohash/32 for !CONFIG_PTE_64BIT
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/d6f8e1f46583f1842de24581a68b0496feb15516.1589866984.git.christophe.leroy@csgroup.eu
Allocate static page tables for the fixmap area. This allows
setting mappings through page tables before memblock is ready.
That's needed to use early_ioremap() early and to use standard
page mappings with fixmap.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4f4b1412d34de6801b8e925cb88fc69d056ff536.1589866984.git.christophe.leroy@csgroup.eu
Mapping RO data as ROX is not an issue since that data
cannot be modified to introduce an exploit.
PPC64 accepts to have RO data mapped ROX, as a trade off
between kernel size and strictness of protection.
On PPC32, kernel size is even more critical as amount of
memory is usually small.
Depending on the number of available IBATs, the last IBATs
might overflow the end of text. Only warn if it crosses
the end of RO data.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/6499f8eeb2a36330e5c9fc1cee9a79374875bd54.1589866984.git.christophe.leroy@csgroup.eu
The 8xx is about to map kernel linear space and IMMR using huge
pages.
In order to display those pages properly, ptdump needs to handle
hugepd tables at PGD level.
For the time being do it only at PGD level. Further patches may
add handling of hugepd tables at lower level for other platforms
when needed in the future.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/630728289158dcfeb06b14d40ed7c4c4e7148cf1.1589866984.git.christophe.leroy@csgroup.eu
Commit 702f098052 ("powerpc/64s/exception: Remove lite interrupt
return") changed the interrupt return path to not restore non-volatile
registers by default, and explicitly restore them in paths where it is
required.
But it missed that the facility unavailable exception can sometimes
modify user registers, ie. when it does emulation of move from DSCR.
This is seen as a failure of the dscr_sysfs_thread_test:
test: dscr_sysfs_thread_test
[cpu 0] User DSCR should be 1 but is 0
failure: dscr_sysfs_thread_test
So restore non-volatile GPRs after facility unavailable exceptions.
Currently the hypervisor facility unavailable exception is also wired
up to call facility_unavailable_exception().
In practice we should never take a hypervisor facility unavailable
exception for the DSCR. On older bare metal systems we set HFSCR_DSCR
unconditionally in __init_HFSCR, or on newer systems it should be
enabled via the "data-stream-control-register" device tree CPU
feature.
Even if it's not, since commit f3c99f97a3 ("KVM: PPC: Book3S HV:
Don't access HFSCR, LPIDR or LPCR when running nested"), the KVM code
has unconditionally set HFSCR_DSCR when running guests.
So we should only get a hypervisor facility unavailable for the DSCR
if skiboot has disabled the "data-stream-control-register" feature,
and we are somehow in guest context but not via KVM.
Given all that, it should be unnecessary to add a restore of
non-volatile GPRs after the hypervisor facility exception, because we
never expect to hit that path. But equally we may as well add the
restore, because we never expect to hit that path, and if we ever did,
at least we would correctly restore the registers to their post
emulation state.
In future we can split the non-HV and HV facility unavailable handling
so that there is no emulation in the HV handler, and then remove the
restore for the HV case.
Fixes: 702f098052 ("powerpc/64s/exception: Remove lite interrupt return")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200526061808.2472279-1-mpe@ellerman.id.au
Several strange crashes have been eventually traced back to
STRICT_KERNEL_RWX and its interaction with code patching.
Various paths in our ftrace, kprobes and other patching code need to
be hardened against patching failures, otherwise we can end up running
with partially/incorrectly patched ftrace paths, kprobes or jump
labels, which can then cause strange crashes.
Although fixes for those are in development, they're not -rc material.
There also seem to be problems with the underlying strict RWX logic,
which needs further debugging.
So for now disable STRICT_KERNEL_RWX on 64-bit to prevent people from
enabling the option and tripping over the bugs.
Fixes: 1e0fc9d1eb ("powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200520133605.972649-1-mpe@ellerman.id.au
In order to alloc sub-arches to alloc KASAN regions using optimised
methods (Huge pages on 8xx, BATs on BOOK3S, ...), declare
kasan_init_region() weak.
Also make kasan_init_shadow_page_tables() accessible from outside,
so that it can be called from the specific kasan_init_region()
functions if needed.
And populate remaining KASAN address space only once performed
the region mapping, to allow 8xx to allocate hugepd instead of
standard page tables for mapping via 8M hugepages.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/3c1ce419fa1b5a4171b92d7fb16455ca17e1b96d.1589866984.git.christophe.leroy@csgroup.eu
kasan_remap_early_shadow_ro() and kasan_unmap_early_shadow_vmalloc()
are both updating the early shadow mapping: the first one sets
the mapping read-only while the other clears the mapping.
Refactor and create kasan_update_early_region()
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/8c496c0828de2608c7c940c45525d177e91b6f1b.1589866984.git.christophe.leroy@csgroup.eu
Commit 45ff3c5595 ("powerpc/kasan: Fix parallel loading of
modules.") added spinlocks to manage parallele module loading.
Since then commit 47febbeeec ("powerpc/32: Force KASAN_VMALLOC for
modules") converted the module loading to KASAN_VMALLOC.
The spinlocking has then become unneeded and can be removed to
simplify kasan_init_shadow_page_tables()
Also remove inclusion of linux/moduleloader.h and linux/vmalloc.h
which are not needed anymore since the removal of modules management.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/81a4d3aee8b82bc1355595935c8f4ad9d3b22a83.1589866984.git.christophe.leroy@csgroup.eu
At the time being, KASAN_SHADOW_END is 0x100000000, which
is 0 in 32 bits representation.
This leads to a couple of issues:
- kasan_remap_early_shadow_ro() does nothing because the comparison
k_cur < k_end is always false.
- In ptdump, address comparison for markers display fails and the
marker's name is printed at the start of the KASAN area instead of
being printed at the end.
However, there is no need to shadow the KASAN shadow area itself,
so the KASAN shadow area can stop shadowing memory at the start
of itself.
With a PAGE_OFFSET set to 0xc0000000, KASAN shadow area is then going
from 0xf8000000 to 0xff000000.
Fixes: cbd18991e2 ("powerpc/mm: Fix an Oops in kasan_mmu_init()")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ae1a3c0d19a37410c209c3fc453634cfcc0ee318.1589866984.git.christophe.leroy@csgroup.eu
In case (k_start & PAGE_MASK) doesn't equal (kstart), 'va' will never be
NULL allthough 'block' is NULL
Check the return of memblock_alloc() directly instead of
the resulting address in the loop.
Fixes: 509cd3f2b4 ("powerpc/32: Simplify KASAN init")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7cb8ca82042bfc45a5cfe726c921cd7e7eeb12a3.1589866984.git.christophe.leroy@csgroup.eu
This option increases the number of SLB misses by limiting the number
of kernel SLB entries, and increased flushing of cached lookaside
information. This helps stress test difficult to hit paths in the
kernel.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Relocate the code into arch/powerpc/mm, s/torture/stress/]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200511125825.3081305-1-mpe@ellerman.id.au
A 0day randconfig uncovered an error with clang, trimmed for brevity:
arch/powerpc/platforms/embedded6xx/wii.c:195:7: error: attribute
declaration must precede definition [-Werror,-Wignored-attributes]
if (!machine_is(wii))
^
The macro machine_is declares mach_##name but define_machine actually
defines mach_##name, hence the warning.
To fix this, move define_machine after the is_machine usage.
Fixes: 5a7ee3198d ("powerpc: wii: platform support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/989
Link: https://lore.kernel.org/r/20200413190644.16757-1-natechancellor@gmail.com
Booting a power9 server with hash MMU could trigger an undefined
behaviour because pud_offset(p4d, 0) will do,
0 >> (PAGE_SHIFT:16 + PTE_INDEX_SIZE:8 + H_PMD_INDEX_SIZE:10)
Fix it by converting pud_index() and friends to static inline
functions.
UBSAN: shift-out-of-bounds in arch/powerpc/mm/ptdump/ptdump.c:282:15
shift exponent 34 is too large for 32-bit type 'int'
CPU: 6 PID: 1 Comm: swapper/0 Not tainted 5.6.0-rc4-next-20200303+ #13
Call Trace:
dump_stack+0xf4/0x164 (unreliable)
ubsan_epilogue+0x18/0x78
__ubsan_handle_shift_out_of_bounds+0x160/0x21c
walk_pagetables+0x2cc/0x700
walk_pud at arch/powerpc/mm/ptdump/ptdump.c:282
(inlined by) walk_pagetables at arch/powerpc/mm/ptdump/ptdump.c:311
ptdump_check_wx+0x8c/0xf0
mark_rodata_ro+0x48/0x80
kernel_init+0x74/0x194
ret_from_kernel_thread+0x5c/0x74
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200306044852.3236-1-cai@lca.pw
Christian reports:
MODPOST vmlinux.o
WARNING: modpost: vmlinux.o(.text.unlikely+0x1a0): Section mismatch in
reference from the function .early_init_mmu() to the function
.init.text:.radix__early_init_mmu()
The function .early_init_mmu() references
the function __init .radix__early_init_mmu().
This is often because .early_init_mmu lacks a __init
annotation or the annotation of .radix__early_init_mmu is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1ac): Section mismatch in
reference from the function .early_init_mmu() to the function
.init.text:.hash__early_init_mmu()
The function .early_init_mmu() references
the function __init .hash__early_init_mmu().
This is often because .early_init_mmu lacks a __init
annotation or the annotation of .hash__early_init_mmu is wrong.
The compiler is uninlining early_init_mmu and not putting it in an init
section because there is no annotation. Add it.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Link: https://lore.kernel.org/r/20200429070247.1678172-1-npiggin@gmail.com
Fixes coccicheck warning:
./arch/powerpc/platforms/powernv/opal.c:813:1-5:
alloc with no test, possible model on line 814
Add NULL check after kzalloc.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200509020838.121660-1-chenzhou10@huawei.com
The ps3's otheros flash loader has a size limit of 16 MiB for the
uncompressed image. If that limit will be reached output the
flash image file as 'otheros-too-big.bld'.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/897c2a59-378e-7c9b-3976-d0a0def90913@infradead.org
With a 64K page size flush with start and end:
(start, end) = (721f680d0000, 721f680e0000)
results in:
(hstart, hend) = (721f68200000, 721f68000000)
ie. hstart is above hend, which indicates no huge page flush is
needed.
However the current logic incorrectly sets hflush = true in this case,
because hstart != hend.
That causes us to call __tlbie_va_range() passing hstart/hend, to do a
huge page flush even though we don't need to. __tlbie_va_range() will
skip the actual tlbie operation for start > end. But it will still end
up calling fixup_tlbie_va_range() and doing the TLB fixups in there,
which is harmless but unnecessary work.
Reported-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop else case, hflush is already false, flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200513030616.152288-1-aneesh.kumar@linux.ibm.com
Merge our topic branch shared with the kvm-ppc tree.
This brings in one commit that touches the XIVE interrupt controller
logic across core and KVM code.
Merge our uaccess-ppc topic branch. It is based on the uaccess topic
branch that we're sharing with Viro.
This includes the addition of user_[read|write]_access_begin(), as
well as some powerpc specific changes to our uaccess routines that
would conflict badly if merged separately.
This reverts commit 697ece78f8.
The implementation of SWAP on powerpc requires page protection
bits to not be one of the least significant PTE bits.
Until the SWAP implementation is changed and this requirement voids,
we have to keep at least _PAGE_RW outside of the 3 last bits.
For now, revert to previous PTE bits order. A further rework
may come later.
Fixes: 697ece78f8 ("powerpc/32s: reorder Linux PTE bits to better match Hash PTE bits.")
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b34706f8de87f84d135abb5f3ede6b6f16fb1f41.1589969799.git.christophe.leroy@csgroup.eu
Add support for 2nd DAWR in xmon. With this, we can have two
simultaneous breakpoints from xmon.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-17-ravi.bangoria@linux.ibm.com
Xmon allows overwriting breakpoints because it's supported by only
one DAWR. But with multiple DAWRs, overwriting becomes ambiguous
or unnecessary complicated. So let's not allow it.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-16-ravi.bangoria@linux.ibm.com
With Book3s DAWR, ptrace and perf watchpoints on powerpc behaves
differently. Ptrace watchpoint works in one-shot mode and generates
signal before executing instruction. It's ptrace user's job to
single-step the instruction and re-enable the watchpoint. OTOH, in
case of perf watchpoint, kernel emulates/single-steps the instruction
and then generates event. If perf and ptrace creates two events with
same or overlapping address ranges, it's ambiguous to decide who
should single-step the instruction. Because of this issue, don't
allow perf and ptrace watchpoint at the same time if their address
range overlaps.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-15-ravi.bangoria@linux.ibm.com
Currently we assume that we have only one watchpoint supported by hw.
Get rid of that assumption and use dynamic loop instead. This should
make supporting more watchpoints very easy.
With more than one watchpoint, exception handler needs to know which
DAWR caused the exception, and hw currently does not provide it. So
we need sw logic for the same. To figure out which DAWR caused the
exception, check all different combinations of user specified range,
DAWR address range, actual access range and DAWRX constrains. For ex,
if user specified range and actual access range overlaps but DAWRX is
configured for readonly watchpoint and the instruction is store, this
DAWR must not have caused exception.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Michael Neuling <mikey@neuling.org>
[mpe: Unsplit multi-line printk() strings, fix some sparse warnings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200514111741.97993-14-ravi.bangoria@linux.ibm.com
Currently we calculate hw aligned start and end addresses manually.
Replace them with builtin ALIGN_DOWN() and ALIGN() macros.
So far end_addr was inclusive but this patch makes it exclusive (by
avoiding -1) for better readability.
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-13-ravi.bangoria@linux.ibm.com
Introduce is_ptrace_bp() function and move the check inside the
function. It will be utilize more in later set of patches.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-12-ravi.bangoria@linux.ibm.com
ptrace_bps is already an array of size HBP_NUM_MAX. But we use
hardcoded index 0 while fetching/updating it. Convert such code
to loop over array.
ptrace interface to use multiple watchpoint remains same. eg:
two PPC_PTRACE_SETHWDEBUG calls will create two watchpoint if
underneath hw supports it.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-11-ravi.bangoria@linux.ibm.com
So far powerpc hw supported only one watchpoint. But Power10 is
introducing 2nd DAWR. Convert thread_struct->hw_brk into an array.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-10-ravi.bangoria@linux.ibm.com
Instead of disabling only first watchpoint, disable all available
watchpoints while clearing dawr_force_enable.
Callback function is used only for disabling watchpoint, rename it
to disable_dawrs_cb(). And null_brk parameter is not really required
while disabling watchpoint, remove it.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-9-ravi.bangoria@linux.ibm.com
Instead of disabling only one watchpoint, get num of available
watchpoints dynamically and disable all of them.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-8-ravi.bangoria@linux.ibm.com
Introduce new parameter 'nr' to __set_breakpoint() which indicates
which DAWR should be programed. Also convert current_brk variable
to an array.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-7-ravi.bangoria@linux.ibm.com
Introduce new parameter 'nr' to set_dawr() which indicates which DAWR
should be programed.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-6-ravi.bangoria@linux.ibm.com
User can ask for num of available watchpoints(dbginfo.num_data_bps)
using ptrace(PPC_PTRACE_GETHWDBGINFO). Return actual number of
available watchpoints on the machine rather than hardcoded 1.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-5-ravi.bangoria@linux.ibm.com
So far we had only one watchpoint, so we have hardcoded HBP_NUM to 1.
But Power10 is introducing 2nd DAWR and thus kernel should be able to
dynamically find actual number of watchpoints supported by hw it's
running on. Introduce function for the same. Also convert HBP_NUM macro
to HBP_NUM_MAX, which will now represent maximum number of watchpoints
supported by Powerpc.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-4-ravi.bangoria@linux.ibm.com
Power10 is introducing second DAWR. Add SPRN_ macros for the same.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-3-ravi.bangoria@linux.ibm.com
Power10 is introducing second DAWR. Use real register names from ISA
for current macros:
s/SPRN_DAWR/SPRN_DAWR0/
s/SPRN_DAWRX/SPRN_DAWRX0/
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-2-ravi.bangoria@linux.ibm.com
This adds emulation support for the following prefixed Fixed-Point
Arithmetic instructions:
* Prefixed Add Immediate (paddi)
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Balamuruhan S <bala24@linux.ibm.com>
[mpe: Squash in get_op() usage]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-31-jniethe5@gmail.com
This adds emulation support for the following prefixed integer
load/stores:
* Prefixed Load Byte and Zero (plbz)
* Prefixed Load Halfword and Zero (plhz)
* Prefixed Load Halfword Algebraic (plha)
* Prefixed Load Word and Zero (plwz)
* Prefixed Load Word Algebraic (plwa)
* Prefixed Load Doubleword (pld)
* Prefixed Store Byte (pstb)
* Prefixed Store Halfword (psth)
* Prefixed Store Word (pstw)
* Prefixed Store Doubleword (pstd)
* Prefixed Load Quadword (plq)
* Prefixed Store Quadword (pstq)
the follow prefixed floating-point load/stores:
* Prefixed Load Floating-Point Single (plfs)
* Prefixed Load Floating-Point Double (plfd)
* Prefixed Store Floating-Point Single (pstfs)
* Prefixed Store Floating-Point Double (pstfd)
and for the following prefixed VSX load/stores:
* Prefixed Load VSX Scalar Doubleword (plxsd)
* Prefixed Load VSX Scalar Single-Precision (plxssp)
* Prefixed Load VSX Vector [0|1] (plxv, plxv0, plxv1)
* Prefixed Store VSX Scalar Doubleword (pstxsd)
* Prefixed Store VSX Scalar Single-Precision (pstxssp)
* Prefixed Store VSX Vector [0|1] (pstxv, pstxv0, pstxv1)
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Balamuruhan S <bala24@linux.ibm.com>
[mpe: Use CONFIG_PPC64 not __powerpc64__, use get_op()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-30-jniethe5@gmail.com
If a prefixed instruction results in an alignment exception, the
SRR1_PREFIXED bit is set. The handler attempts to emulate the
responsible instruction and then increment the NIP past it. Use
SRR1_PREFIXED to determine by how much the NIP should be incremented.
Prefixed instructions are not permitted to cross 64-byte boundaries. If
they do the alignment interrupt is invoked with SRR1 BOUNDARY bit set.
If this occurs send a SIGBUS to the offending process if in user mode.
If in kernel mode call bad_page_fault().
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-29-jniethe5@gmail.com
Do not allow placing xmon breakpoints on the suffix of a prefix
instruction.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Don't split printf strings across lines]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-27-jniethe5@gmail.com
Expand the feature-fixups self-tests to includes tests for prefixed
instructions.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Use CONFIG_PPC64 not __powerpc64__, add empty inlines]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-26-jniethe5@gmail.com
Expand the code-patching self-tests to includes tests for patching
prefixed instructions.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Use CONFIG_PPC64 not __powerpc64__]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-25-jniethe5@gmail.com
For powerpc64, redefine the ppc_inst type so both word and prefixed
instructions can be represented. On powerpc32 the type will remain the
same. Update places which had assumed instructions to be 4 bytes long.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
[mpe: Rework the get_user_inst() macros to be parameterised, and don't
assign to the dest if an error occurred. Use CONFIG_PPC64 not
__powerpc64__ in a few places. Address other comments from
Christophe. Fix some sparse complaints.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-24-jniethe5@gmail.com
Currently patch_imm32_load_insns() is used to load an instruction to
r4 to be emulated by emulate_step(). For prefixed instructions we
would like to be able to load a 64bit immediate to r4. To prepare for
this make patch_imm64_load_insns() take an argument that decides which
register to load an immediate to - rather than hardcoding r3.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200516115449.4168796-1-mpe@ellerman.id.au
Add the BOUNDARY SRR1 bit definition for when the cause of an
alignment exception is a prefixed instruction that crosses a 64-byte
boundary. Add the PREFIXED SRR1 bit definition for exceptions caused
by prefixed instructions.
Bit 35 of SRR1 is called SRR1_ISI_N_OR_G. This name comes from it
being used to indicate that an ISI was due to the access being no-exec
or guarded. ISA v3.1 adds another purpose. It is also set if there is
an access in a cache-inhibited location for prefixed instruction.
Rename from SRR1_ISI_N_OR_G to SRR1_ISI_N_G_OR_CIP.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-23-jniethe5@gmail.com
Prefix instructions have their own FSCR bit which needs to enabled via
a CPU feature. The kernel will save the FSCR for problem state but it
needs to be enabled initially.
If prefixed instructions are made unavailable by the [H]FSCR, attempting
to use them will cause a facility unavailable exception. Add "PREFIX" to
the facility_strings[].
Currently there are no prefixed instructions that are actually emulated
by emulate_instruction() within facility_unavailable_exception().
However, when caused by a prefixed instructions the SRR1 PREFIXED bit is
set. Prepare for dealing with emulated prefixed instructions by checking
for this bit.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Link: https://lore.kernel.org/r/20200506034050.24806-22-jniethe5@gmail.com
test_translate_branch() uses two pointers to instructions within a
buffer, p and q, to test patch_branch(). The pointer arithmetic done on
them assumes a size of 4. This will not work if the instruction length
changes. Instead do the arithmetic relative to the void * to the buffer.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-21-jniethe5@gmail.com
When a new breakpoint is created, the second instruction of that
breakpoint is patched with a trap instruction. This assumes the length
of the instruction is always the same. In preparation for prefixed
instructions, remove this assumption. Insert the trap instruction at the
same time the first instruction is inserted.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-20-jniethe5@gmail.com
Currently in xmon, mread() is used for reading instructions. In
preparation for prefixed instructions, create and use a new function,
mread_instr(), especially for reading instructions.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-19-jniethe5@gmail.com
Currently all instructions have the same length, but in preparation for
prefixed instructions introduce a function for returning instruction
length.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-18-jniethe5@gmail.com
Define specialised get_user_instr(), __get_user_instr() and
__get_user_instr_inatomic() macros for reading instructions from user
and/or kernel space.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
[mpe: Squash in addition of get_user_instr() & __user annotations]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-17-jniethe5@gmail.com
Instead of using memcpy() and flush_icache_range() use
patch_instruction() which not only accomplishes both of these steps but
will also make it easier to add support for prefixed instructions.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-16-jniethe5@gmail.com
Introduce a probe_kernel_read_inst() function to use in cases where
probe_kernel_read() is used for getting an instruction. This will be
more useful for prefixed instructions.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
[mpe: Don't write to *inst on error]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-15-jniethe5@gmail.com
Introduce a probe_user_read_inst() function to use in cases where
probe_user_read() is used for getting an instruction. This will be
more useful for prefixed instructions.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
[mpe: Don't write to *inst on error, fold in __user annotations]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-14-jniethe5@gmail.com
Prefixed instructions will mean there are instructions of different
length. As a result dereferencing a pointer to an instruction will not
necessarily give the desired result. Introduce a function for reading
instructions from memory into the instruction data type.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-13-jniethe5@gmail.com
Currently unsigned ints are used to represent instructions on powerpc.
This has worked well as instructions have always been 4 byte words.
However, ISA v3.1 introduces some changes to instructions that mean
this scheme will no longer work as well. This change is Prefixed
Instructions. A prefixed instruction is made up of a word prefix
followed by a word suffix to make an 8 byte double word instruction.
No matter the endianness of the system the prefix always comes first.
Prefixed instructions are only planned for powerpc64.
Introduce a ppc_inst type to represent both prefixed and word
instructions on powerpc64 while keeping it possible to exclusively
have word instructions on powerpc32.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Fix compile error in emulate_spe()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-12-jniethe5@gmail.com
In preparation for an instruction data type that can not be directly
used with the '==' operator use functions for checking equality.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balamuruhan S <bala24@linux.ibm.com>
Link: https://lore.kernel.org/r/20200506034050.24806-11-jniethe5@gmail.com
Use a function for byte swapping instructions in preparation of a more
complicated instruction type.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balamuruhan S <bala24@linux.ibm.com>
Link: https://lore.kernel.org/r/20200506034050.24806-10-jniethe5@gmail.com
In preparation for using a data type for instructions that can not be
directly used with the '>>' operator use a function for getting the op
code of an instruction.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-9-jniethe5@gmail.com
In preparation for introducing a more complicated instruction type to
accommodate prefixed instructions use an accessor for getting an
instruction as a u32.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-8-jniethe5@gmail.com
In preparation for instructions having a more complex data type start
using a macro, ppc_inst(), for making an instruction out of a u32. A
macro is used so that instructions can be used as initializer elements.
Currently this does nothing, but it will allow for creating a data type
that can represent prefixed instructions.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Change include guard to _ASM_POWERPC_INST_H]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-7-jniethe5@gmail.com
create_branch(), create_cond_branch() and translate_branch() return the
instruction that they create, or return 0 to signal an error. Separate
these concerns in preparation for an instruction type that is not just
an unsigned int. Fill the created instruction to a pointer passed as
the first parameter to the function and use a non-zero return value to
signify an error.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-6-jniethe5@gmail.com
A modulo operation is used for calculating the current offset from a
breakpoint within the breakpoint table. As instruction lengths are
always a power of 2, this can be replaced with a bitwise 'and'. The
current check for word alignment can be replaced with checking that the
lower 2 bits are not set.
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-5-jniethe5@gmail.com
The instructions for xmon's breakpoint are stored bpt_table[] which is in
the data section. This is problematic as the data section may be marked
as no execute. Move bpt_table[] to the text section.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-4-jniethe5@gmail.com
To execute an instruction out of line after a breakpoint, the NIP is set
to the address of struct bpt::instr. Here a copy of the instruction that
was replaced with a breakpoint is kept, along with a trap so normal flow
can be resumed after XOLing. The struct bpt's are located within the
data section. This is problematic as the data section may be marked as
no execute.
Instead of each struct bpt holding the instructions to be XOL'd, make a
new array, bpt_table[], with enough space to hold instructions for the
number of supported breakpoints. A later patch will move this to the
text section.
Make struct bpt::instr a pointer to the instructions in bpt_table[]
associated with that breakpoint. This association is a simple mapping:
bpts[n] -> bpt_table[n * words per breakpoint]. Currently we only need
the copied instruction followed by a trap, so 2 words per breakpoint.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-3-jniethe5@gmail.com
For modifying instructions in xmon, patch_instruction() can serve the
same role that store_inst() is performing with the advantage of not
being specific to xmon. In some places patch_instruction() is already
being using followed by store_inst(). In these cases just remove the
store_inst(). Otherwise replace store_inst() with patch_instruction().
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Link: https://lore.kernel.org/r/20200506034050.24806-2-jniethe5@gmail.com
The ps3_mm_region_destroy() and ps3_mm_vas_destroy() routines
are called very late in the shutdown via kexec's mmu_cleanup_all
routine. By the time mmu_cleanup_all runs it is too late to use
udbg_printf, and calling it will cause PS3 systems to hang.
Remove all debugging statements from ps3_mm_region_destroy() and
ps3_mm_vas_destroy() and replace any error reporting with calls
to lv1_panic.
With this change builds with 'DEBUG' defined will not cause kexec
reboots to hang, and builds with 'DEBUG' defined or not will end
in lv1_panic if an error is encountered.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7325c4af2b4c989c19d6a26b90b1fec9c0615ddf.1589049250.git.geoff@infradead.org
System Reset and Machine Check interrupts that are not recoverable due
to being nested or interrupting when RI=0 currently panic. This is not
necessary, and can often just kill the current context and recover.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200508043408.886394-16-npiggin@gmail.com
Similarly to the previous patch, do not trace system reset. This code
is used when there is a crash or hang, and tracing disturbs the system
more and has been known to crash in the crash handling path.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20200508043408.886394-15-npiggin@gmail.com
Rather than notrace annotations throughout a significant part of the
machine check code across kernel/ pseries/ and powernv/ which can
easily be broken and is infrequently tested, use paca->ftrace_enabled
to blanket-disable tracing of the real-mode non-maskable handler.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20200508043408.886394-14-npiggin@gmail.com
