If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cris allmodconfig:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
drivers/tty/serial/max310x.c:885:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
drivers/tty/serial/max310x.c:916:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a temporary solution to fix following issue:
config: make ARCH=alpha allyesconfig
All error/warnings:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
>> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function)
drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function)
>> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e3c6ea9b1b as it
didn't help anything, and caused more problems than expected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
config: x86_64-randconfig-x006 (attached as .config)
All warnings:
drivers/tty/serial/max310x.c: In function 'max310x_probe':
>> drivers/tty/serial/max310x.c:1240:1: warning: label 'out_uart' defined but not used [-Wunused-label]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
config: make ARCH=alpha allyesconfig
All error/warnings:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
>> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function)
drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function)
>> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds devicetree support for the MAX310X serial driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes some unused definitions from driver code and
sort #includes alphabetically.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for RS-485 (TIOCSRS485/TIOCGRS485) IOCTLs.
As a result this patch eliminate private driver header.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always register GPIOs and use dynamic GPIO ID assignment.
This is no much worth if GPIOs is not used, but helps remove
private driver header and add DT support in the future.
Additionally, patch adds missing uart_unregister_driver()
call if probe() fails.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes "frequency" parameter from MAX310X platform_data
and uses CLK API for getting clock. Clock type (XTAL/OSC) is
determined by clk name.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch move all SPI-dependent stuff in one place. This include move
PM-function definitions out of CONFIG_SPI_MASTER and move regmap
initialization out of common probe into CONFIG_SPI_MASTER which
may help to add I2C support in the future for this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes excess IRQ checks at driver probe().
IRQ validation is already provided by request_threaded_irq().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces loopback mode support from platform data to
dynamic setup with TIOCMSET ioctl.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core calls set_termios() after port startup, so there are
no reason to setup port twice.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These callbacks were previously used for the IC power initialization.
If this initialization will be needed in the future, it should be
implemented with the regulator API.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provide more precisely setup of baud rate generator.
If the result of division has a remainder, we use the multiplier
for the base frequency. Additionally, we report result baud rate
back to serial core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and while blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes wrong dev_pm_ops which caused by commit:
serial: max310x: Driver rework.
CC drivers/tty/serial/max310x.o
LD drivers/video/fb.o
CC drivers/w1/slaves/w1_ds2433.o
CC drivers/w1/slaves/w1_ds2760.o
CC drivers/xen/balloon.o
CC drivers/video/backlight/adp8870_bl.o
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.suspend') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.resume') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.freeze') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.thaw') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.poweroff') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.restore') [enabled by default]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX14830 (advanced quad universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX3109 (advanced dual universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rework max310x driver.
Major changes have been made:
- Prepare driver to support ICs with more than one UART.
- Prepare driver to support work with I2C-bus.
The patch changes almost every function and can not be divided into parts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_pm_ops instead of the deprecated legacy suspend/resume for the
max310x driver.
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spi_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to explicitly call devm_kfree
in probe or remove functions.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpiochip_remove function may fail to remove a gpio_chip
if any GPIOs are still requested. This patch informs the caller
of such a senario.
Sparse is warning because the function prototype has a
__must_check annotation.
Sparse warning:
drivers/tty/serial/max310x.c:1223:18: warning:
ignoring return value of ‘gpiochip_remove’,
declared with attribute warn_unused_result
[-Wunused-result]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is a replacement for a MAX3107 driver with a lot of
improvements and new features.
The main differences from the old version:
- Using the regmap.
- Using devm_XXX-related functions.
- The use of threaded IRQ with IRQF_ONESHOT flag allows the driver to
the hardware that supports only level IRQ.
- Improved error handling of serial port, improved FIFO handling,
improved hardware & software flow control.
- Advanced flags allows turn on RS-485 mode (Auto direction control).
- Ability to load multiple instances of drivers.
- Added support for MAX3108.
- GPIO support.
- Driver is quite ready for adding I2C support and support other ICs
with compatible registers set (MAX3109, MAX14830).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
