This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags. This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.
The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.
(Strictly speaking, the authorized_default flag should become atomic
as well. I didn't bother with it because it gets changed only via
sysfs. It can be done later, if anyone wants.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop the unnecessary empty stubs in tusb6010.c and avoid
a compile error when building kernel for n8x0.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting MUSB Burst Mode 3 automatically enables support for
lower burst modes (BURST4, BURST8, BURST16 or bursts of unspecified
length). There is no need to set these burst modes based on the
packet size. Also enable the burst mode for both mode1 and mode0.
This is a fix for buggy hardware - having the lower burst modes
enabled can potentially cause lockups of the DMA engine used in
OMAP2/3/4 chips.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new ulpi code defines fallback stubs for the Blackfin arch, but does
so incorrectly leading to a build failure:
drivers/usb/musb/musb_core.c:227: error: 'musb_ulpi_read' undeclared here (not in a function)
drivers/usb/musb/musb_core.c:228: error: 'musb_ulpi_write' undeclared here (not in a function)
Tweak the fallback stubs so that they do work as intended.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attempt to build MUSB driver with CONFIG_PM=y (e.g. in the OTG mode) on DaVinci
results in these link errors:
drivers/built-in.o: In function `musb_restore_context':
led-triggers.c:(.text+0x714d8): undefined reference to
`musb_platform_restore_context'
drivers/built-in.o: In function `musb_save_context':
led-triggers.c:(.text+0x71788): undefined reference to
`musb_platform_save_context'
This turned out to be caused by commit 9957dd97ec
(usb: musb: Fix compile error for omaps for musb_hdrc). Revert it, taking into
account the rename of CONFIG_ARCH_OMAP34XX into CONFIG_ARCH_OMAP3 (which that
commit fixed in a completely inappropriate way) and the recent addition of
OMAP4 support.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 1c25fda4a0 (usb: musb: handle irqs in the
order dictated by programming guide) forgot to get rid of the old 'STAGE0_MASK'
filter for calling musb_stage0_irq(), so now disconnect and suspend interrupts
are effectively ignored...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a part of aligning the ISR code for MUSB with the specs, the
ISR code was re-written.
See Commit 1c25fda4a0 (usb: musb: handle
irqs in the order dictated by programming guide)
With this the suspend interrupt came accidently under CONFIG_USB_MUSB_HDRC_HCD.
The fix brings suspend interrupt handling outside
CONFIG_USB_MUSB_HDRC_HCD.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds helper functions for ULPI access, and implements
otg_io_access_ops for musb.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the unexistent CONFIG_USB_INVENTRA_MUSB_HAS_AHB_ID
option from our Makefile.
Problem reported by Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need mach-types and hardware.h
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
get_cpu_rev() is unused in this driver. It is probably legacy
code. So remove it.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These functions do nothing and also are both unnecessarily 'extern'; actually,
musb_platform_resume() in not even called...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function is only called inside omap2430.c...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function does nothing...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function does nothing...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when we fail to probe(), we can call musb_exit_debugfs().
Allow that by removing section annotations.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and simplify the was we read/write from/to
DMA COUNT register.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we can support the musb-specific test modes on the
vendor specific range of test selector as stated
on USB Specification Table 9-7 Test Mode Selectors.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
for now only a simple register dump entry (which can
be rather useful on debugging) and a way to start
test modes.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than hardcoding the gpio levels for vrsel, allow the platform
resources to handle this so boards can be active high or low.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the Makefile to build the
MUSB driver for OMAP4. It also sets the Kconfig
options for OMAP4.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Program the OTG_INTERFSEL register based on
transcevier type passed from board file.
Adapt signature of musb_platform_init() function
for davinci, blackfin and tusb6010.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
boards might want to optimize their fifo configuration
to the particular needs of that specific board. Allow
that by moving all related data structures to
<linux/usb/musb.h>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1349b) clears up the confusion in many USB host
controller drivers between port features and port statuses. In mosty
cases it's true that the status bit is in the position given by the
corresponding feature value, but that's not always true and it's not
guaranteed in the USB spec.
There's no functional change, just replacing expressions of the form
(1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 18eabe2347 introduced
DMA buffer ownership. Fix tusb6010 accordingly. To compile,
also dummy musb_platform_save and restore functions need to
be added.
Also change the order of musb_read_fifo() to happen after
dma_cache_maint to have the DMA operations completed before
moving the remaining unaligned bytes with PIO. The DMA
access and PIO touch different areas of the FIFO, so this
change only makes the code a bit easier to follow.
Tested on n810 and g_ether with variable size ping test.
The test seems to fail for some ping sizes, but that seems to
be a different problem.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function forgets to call usb_remove_hcd() or musb_gadget_cleanup() iff
sysfs_create_group() fails.
[ felipe.balbi@nokia.com : review the entire error path
not only when we fail hcd or gadget ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONFIG_ARCH_DAVINCI now embraces both the "real" DaVinci and DA8xx/OMAP-L1x --
on which the DaVinci glue layer won't work. Change the Makefile dependency to
CONFIG_ARCH_DAVINCI_DMx which corresponds to "real" DaVinci.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
musb_platform_exit() is called twice from musb_init_controller() iff controller
initialization fails. Move the call (and the DevCtl register writes surrounding
it) from musb_free() to musb_remove().
Fix mispalced and now incorrect 'goto's in musb_init_controller().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate/unbalanced call to clk_put() from musb_platform_exit() --
clk_put() gets called from musb_core.c anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function forgets to call clk_disable() iff reading the USB module version
register returns 0.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resetting 'musb->clock' to NULL in musb_shutdown() prevents musb_platform_exit()
from properly disabling the clock when unloading the driver -- don't do it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate/unbalanced calls to clk_disable()/clk_put() in musb_free():
- clk_disable() is called by musb_platform_exit() just prior to this call;
- clk_put() is called by the callers of musb_free() prior to calling it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We assign "urb->hcpriv = qh;" a few lines down. I'm pretty sure we
want it "urb->hcpriv" to be NULL not a freed value.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit a5073b5283 (musb_gadget: fix unhandled
endpoint 0 IRQs) misses this change to blackfin.c: stop faking successful
result of blackfin_interrupt() and emitting a debug message on an unhandled
interrupt.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
... and avoid a compilation if we disable host side
of musb.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit "usb: musb: Add context save and restore support" added
some stubs for the Blackfin code so things would compile, but it also
added a bunch of warnings due to missing return statements.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY.
However, it has no ULPI support - so there are no registers at all.
That means accesses to ULPI_BUSCONTROL have to be abstracted away
like other MUSB registers.
This fixes building for Blackfin parts again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONFIG_ARCH_OMAP34XX is now CONFIG_ARCH_OMAP3.
But since drivers/usb/musb/omap2430.c use CONFIG_PM for these
registers and functions, do the same for the header.
Otherwise we get the following for most omap3 defconfigs:
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'while'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'while'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit "usb: musb: Fix for isochronous IN transfer" (f82a689fa)
seems to have been against an older kernel version. It uses the old style
naming of variables. Unfortunately, this breaks building for most MUSB
users out there since "bDesiredMode" has been renamed to "desired_mode".
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits)
USB: backlight, appledisplay: fix incomplete registration failure handling
USB: pl2303: remove unnecessary reset of usb_device in urbs
USB: ftdi_sio: remove obsolete check in unthrottle
USB: ftdi_sio: remove unused tx_bytes counter
USB: qcaux: driver for auxiliary serial ports on Qualcomm devices
USB: pl2303: initial TIOCGSERIAL support
USB: option: add Longcheer/Longsung vendor ID
USB: fix I2C API usage in ohci-pnx4008.
USB: usbmon: mask seconds properly in text API
USB: sisusbvga: no unnecessary GFP_ATOMIC
USB: storage: onetouch: unnecessary GFP_ATOMIC
USB: serial: ftdi: add CONTEC vendor and product id
USB: remove references to port->port.count from the serial drivers
USB: tty: Prune uses of tty_request_room in the USB layer
USB: tty: Add a function to insert a string of characters with the same flag
USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()
USB: tty: kill request_room for USB ACM class
USB: tty: sort out the request_room handling for whiteheat
USB: storage: fix misplaced parenthesis
USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers
...
The removed part always evaluates to false.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Trying to use double buffer modes in RTL versions <2.0 may result in
infinite hangs or data corruption. So avoid them with older versions.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All current Blackfin parts are using RTL v1.9, but they don't expose the
hardware registers to probe this dynamically. So hardcode the version to
v1.9 for now.
Need to move the local hwvers related defines higher up in the header so
that sub-musb headers may utilize them.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we were printing the info about musb probe too early where
it was still possible for things to go wrong. Move the
down right before the return 0 statement. While at that
also convert pr_info to dev_info.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when probe() fails, we should iounmap() the mapped address.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and even added a flag to struct musb, so let's
use that.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we have those addresses already ioremaped, so let's
use our __raw_readl/writel wrappers.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding support for MUSB register save and restore during system
suspend and resume.
Changes:
- Added musb_save/restore_context() functions
- Added platform specific musb_platform_save/restore_context()
to handle platform specific jobs.
- Maintaining BlackFin compatibility by adding read/write
functions for registers which are not available in BlackFin
Tested system suspend and resume on OMAP3EVM board.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Test whether tusb_dma is not NULL before dereferencing
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the board might use external Vbus power supply on musb
interface which would require to program ULPI_BUSCONTROL register.
Adding 'extvbus' flag which can be set from such boards which will
be checked at musb driver files before programming ULPI_BUSCONTROL.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Save dynamic FIFO read only information for later uses during
musb_save/restore_context functions.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB's programming guide dictates how we should handle its
irqs and in which order. Follow that.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The version applied had a few comments which are now
done.
Thanks to Sergei for pointing out.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the Tx abort/teardown logic. We now wait for the teardown
completion interrupt and acknowledge the same by setting the tx_complete
register to 0.
This change is needed to ensure that abort processing works on DM365 platform.
Without this change after completion of abort processing the system is
overwhelmed with continuous stream of abort interrupts.
This change has been tested on all CPPI3.x platforms (DM644x, DM646x, DM35x,
DM36x).
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements the work around for a Mentor controller related
bug where it's observed a BULK Tx toggle error on the bus when a
BULK IO gets scheduled on an endpoint that was earlier used for
handling ISOC transaction and needed to start on 1 toggle. When such
a situation arises even if the TXCSR toggle bits are programmed
correctly by the musb driver the data gets transmitted with 0 toggle
which leads to toggle error on the bus and the BULK transaction fails.
In case of MSC write, the device gets reset by the Host.
This Mentor bug is observed on almost all Mentor versions (1.3, 1.5,
1.8). Confirmed on DM644x, DM355, DM365, OMAPL13x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB DMA_INTR register may sometimes read zero when infact there
was a pending interrupt. Workaround this by reading the DMA_COUNT
values for all enabled channels when this condition occurs.
Flag these channels as the ones needing to be serviced.
Additionally, the absence of a debug print meant we would never
catch a spurious DMA interrupt in MUSB. So this patch adds a
debug print in the IRQ handler.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a wrapper for reading the DMA count register, analogous
to the one for writing to this register.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have observed MSC data read corruption when USB LAN device is
also connected and it's interface is up.
Silicon team has confirmed an errata where in all the active
transfers should use FIFO space either in first 8K or next 8K.
So far we have observed the issue in above use case scenario.
As a workaround to it, adding a new FIFO config (5) fitting well
within first 8K which can be used for such use cases.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it's easier to keep up and add more sysfs entries
as necessary.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some of these workarounds are already in place, but labeled as affecting
all BF52x parts. Since we have official anomaly numbers now, use those
defines. And since writing to the FIFO has a similar hang issue as reading
from the FIFO, implement the workaround there too when necessary.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below array index out of bounds issue.
Buffer overflow, array index of 'aInfo' may be out of
bounds. Array 'aInfo' of size 78 may use index value(s) 6..84
The data stored in 'aInfo' array exceeds the array size of 78.
This patch increases the size of this array to hold the string
correctly without any memory corruption.
This issue was reported by Klockwork tool.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following NULL pointer dereference issue.
Pointer 'request' returned from call to function 'next_request'
at line 748 may be NULL and may be dereferenced at line 792.
============
Code Snippet
============
748: request = next_request(musb_ep);
785: if (dma && (csr & MUSB_RXCSR_DMAENAB)) {
csr &= ~(MUSB_RXCSR_AUTOCLEAR
| MUSB_RXCSR_DMAENAB
| MUSB_RXCSR_DMAMODE);
musb_writew(epio, MUSB_RXCSR,
MUSB_RXCSR_P_WZC_BITS | csr);
792: request->actual += musb_ep->dma->actual_len;
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since a DMA transfer may need to be kicked off several times to complete,
the DMA start must include the length that has already been transferred.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadget stalling a zero-length SETUP request results in this error message:
SetupEnd came in a wrong ep0stage idle
In order to avoid it, always set the CSR0.DataEnd bit after detecting a zero-
length request. Add the missing '\n' to the error message itself as well...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Race condition exists between the cppi_interrupt handler and
davinci_interrupt handler w.r.t completing a TX IO. Since DM646x
has seperate DMA and USB endpoint interrupts cppi_interrupt handler
needs to hold the lock while operating on the endpoint.
Update over previous patch to avoid taking the lock if already
taken. Tested on DM644x, DM355 and DM646x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On OTG and gadget-only configurations, we need a gadget driver
in order to work properly, so avoid changing operation modes
when there's no gadget driver loaded.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When registering gadget driver, the state of the transceiver
must be set from undefined (no gadget) to b_idle.
Module unload sets the transceiver state to undefined state.
After the first load/unload pair, the reset irq will be lost.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a null-pointer dereference bug.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current musb gadget dma code produces the warning:
drivers/usb/musb/musb_gadget.c: In function 'txstate':
drivers/usb/musb/musb_gadget.c:312: warning: comparison of distinct
pointer types lacks a cast
So switch to min_t(size_t, ...).
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
probe() already was on __init, so moving remove() to __exit.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 7723de7e19 (USB: musb_gadget: remove
pointless loop) included uncalled for (and incorrect) optimization that
might cause a kernel oops in txstate() -- undo it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
drivers/usb/musb/musb_host.c:1642:9: warning: symbol 'status' shadows an earlier one
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warnings:
drivers/usb/musb/musb_gadget.c:1161:5: warning: symbol 'musb_gadget_set_halt' was not declared. Should it be static?
drivers/usb/musb/musb_gadget.c:1244:5: warning: symbol 'musb_gadget_set_wedge' was not declared. Should it be static?
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
drivers/usb/musb/omap2430.c:314:16: warning: Using plain integer as NULL pointer
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the pointless 'do () while (0)' loop from musb_g_tx() -- it
makes this function symmetric to musb_g_rx()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop playing with musb->lock and abusing musb_gadget_set_halt() in
the code clearing the endpoint halt feature -- instead, manipulate
the registers directly.
While at it, get rid uf unneeded line breaks and over-indentation in
the code setting the endpoint halt feature.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement the driver's set_wedge() method by adding the 'wedged' flag
to the 'struct musb_ep'.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit a5073b5283 (musb_gadget: fix
unhandled endpoint 0 IRQs) somehow missed its key change:
"The gadget EP0 code routinely ignores an interrupt at end of
the data phase because of musb_g_ep0_giveback() resetting the
state machine to "idle, waiting for SETUP" phase prematurely."
So, the majority of the cases of unhandled IRQs is still unfixed...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB: save hardware revision at init
This can be used later to flag workarounds for issues affecting
particular revisions. Saving this at init avoids having to
read the HWVERS register multiple times in code.
While at it, use macros to extract the version information
instead of using hardcoded values.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The debug code in the DMA ISR uses a %d for a size_t when it should be
using %zu. Otherwise gcc whines with:
drivers/usb/musb/musbhsdma.c: In function 'dma_controller_irq':
drivers/usb/musb/musbhsdma.c:288: warning: format '%d' expects type 'int',
but argument 7 has type 'size_t'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Otherwise we get the link failure:
drivers/built-in.o: In function 'musb_platform_init':
drivers/usb/musb/blackfin.c:300: undefined reference to 'usb_nop_xceiv_register'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since we can't work around anomaly 05000380, throw a build error up and
instruct the user to use a different mode.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we clear the interrupt pending bits at the end, we sometimes return too
fast and have the same interrupt assert itself. There is no way in a
Blackfin system to force a sync of this state, so the hardware manual
instructs people to clear interrupt flags early in their ISR.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only allow USE_MODE1 when the Blackfin part is not affected by anomaly
05000456 (USB Receive Interrupt Is Not Generated in DMA Mode 1) since we
can't support the mode in that case.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add some helpful notes about how the driver works around different
anomalies that exist in the on-chip host controller.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not allow MUSB driver to be selected on derivatives that don't have the
MUSB controller on them.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin version of musb_read_target_reg_base() returns a u16 when the
common code expects a (void __iomem *), so update the Blackfin function to
return the right value. This fixes the compile warning:
drivers/usb/musb/musb_core.c: In function 'musb_core_init':
drivers/usb/musb/musb_core.c:1448: warning: assignment makes pointer from
integer without a cast
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Otherwise gcc will whine about epnum/dma_reg being unused when building
for BF54x parts.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().
By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.
This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.
Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Babu Ravi <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.
Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate(). And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...
While at it, also do the following changes :
- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
driver does not allow stalling with non-empty Tx FIFO anyway);
- in rxstate(), stop pointlessly zeroing the 'csr' variable;
- in musb_gadget_set_halt(), move the 'done' label to a more proper
place;
- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MUSB code relies on platform implementations that currently only
exists for Arm and Blackfin processors, so have the MUSB Kconfig depend
upon those arches.
This should prevent other arches from building MUSB via randconfig.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Blackfin port doesn't support HAVE_CLK and the musb driver works fine
with support stubbed out, so take the existing Blackfin clk stubs and move
them to common musb code so we can drop the Kconfig dependency.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Invoke put_device(musb->xceiv->dev) before musb_platform_exit()as
xceiv is getting unregistered in musb_platform_exit().
Fixes put_device() panic when module insert/removal is performed
multiple times.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.
Cleanups being done:
- Remove unwanted code in usb-musb.c file
- Register NOP in OMAP3EVM board file using
usb_nop_xceiv_register().
- Select NOP_USB_XCEIV for OMAP3EVM boards.
- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
INDEX register has to be set to '0' before reading
CONFIGDATA register which is only present in TI musb
platforms.
Currently the default register access mode is set to
FLAT_MODE thus INDEX register is not getting set
properly with musb_ep_select() which is just a nop
operation in FLAT_MODE.This invalid register read is
causing module reinset failure.
Fixing the issue by moving INDEX register write part to
musb_read_configdata() function itself.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
musb_otg_timer_func() is defined under #ifdef CONFIG_USB_MUSB_OTG.
Make sure any reference to it is also under the same #ifdef.
Without this fix, the driver failes to compile when USB_OTG is defined
but USB_MUSB_OTG isn't.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function uses wrong bit mask to prevent clearing RXCSR status
bits when halting an endpoint -- which results in clearing SentStall
and RxPktRdy bits (that the code actually tries to avoid); must be
a result of cut-and-paste...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reworks platform driver power management code
for musb from legacy callbacks to dev_pm_ops.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend() -> suspend()
resume_early() -> resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit c9cd06b3d6 (musb_host: refactor
URB giveback) included due to my overlook the change incorrect in the
context of the current kernel -- undo it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of some obnoxious and inappropriate messaging, mostly on
DaVinci, when usbcore tries to autosuspend a root hub if just a
mini/micro-A connector is connected. Symptom: endless stream of
messages reading like:
musb_bus_suspend 2221: trying to suspend as a_wait_vrise is_active=1
Improve that musb bus suspend primitive a bit. Take advantage of
this call to update the OTG state machine if appropriate, moving
the device out of the A_WAIT_VRISE state. There's basically no
timer for that state transition just now, except with tusb6010;
that can make trouble.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Numbering for GPIOs on the pcf857x chips on the dm644x EVM board
changed when DaVinci chips with more GPIOs were supported. Update
the GPIO number used for nVBUS_DRV.
Longer term, we need a better abstraction of board-specific setup in
this code so we're not hard-coding board specific GPIOs into the
driver, but for now this at least gets it back to working with
mainline davinci core code.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Finish merging updates for DM355 chips into musb/davinci.c now
that its support is in mainline: kick in new DRVVBUS controls.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Omap3 MUSB AUTOIDLE functionality configured through OTG_SYSCONFIG
register prevents the device from going into retention.
This is a workaround (by Richard Woodruff/TI), as his comment :
> A new MUSB bug which is a match to data below was identified very
> recently (on hardware and in simulation).
> This bug is in 3430 and not 3630.
> As a priority test (and as new default) you should have engineers
> disable autoidle for MUSB block.
> This is the workaround which will show up in next errata.
Signed-off-by: Niilo Minkkinen <ext-niilo.1.minkkinen@nokia.com>
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tested on OMAP3 host side with Creative (Live! Cam Optia) USB camera
which uses high bandwidth isochronous IN endpoints. FIFO mode 4 is
updated to provide the needed 4K endpoint buffer without breaking
the g_nokia composite gadget configuration. (This is the only
gadget driver known to use enough endpoints to notice the change.)
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Currently, with Inventra DMA, we use Mode 0 if transfer size is less
than or equal to the endpoint's maxpacket size. This requires that
we explicitly set TXPKTRDY for that transfer.
However the musb_g_tx code will not set TXPKTRDY twice if the last
transfer is exactly equal to maxpacket, even if request->zero is set.
Using Mode 1 will solve this; a better fix might be in musb_g_tx().
Without this change, musb will not correctly send out a ZLP if the
last transfer is the maxpacket size and request->zero is set.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adjust HNP state machines in MUSB driver so that they handle the
case where the cable is disconnected. The A-side machine was
very wrong (unrecoverable); the B-Side was much less so.
- A_PERIPHERAL ... as usual, the non-observability of the ID
pin through Mentor's registers makes trouble. We can't go
directly to A_WAIT_VFALL to end the session and start the
disconnect processing. We can however sense link suspending,
go to A_WAIT_BCON, and from there use OTG timeouts to finally
trigger that A_WAIT_VFALL transition. (Hoping that nobody
reconnects quickly to that port and notices the wrong state.)
- B_HOST ... actually clear the Host Request (HR) bit as the
messages say, disconnect the peripheral from the root hub,
and don't detour through a suspend state. (In some cases
this would eventually have cleaned up.)
Also adjust the A_SUSPEND transition to respect the A_AIDL_BDIS
timeout, so if HNP doesn't trigger quickly enough the A_WAIT_VFALL
transition happens as it should.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor HNP bugfixes, so the initial role switch works:
- A-Device:
* disconnect-during-suspend enters A_PERIPHERAL state
* kill OTG timer after reset as A_PERIPHERAL ...
* ... and also pass that reset to the gadget
* once HNP succeeds, clear the "ignore_disconnect" flag
* from A_PERIPHERAL, disconnect transitions to A_WAIT_BCON
- B-Device:
* kill OTG timer on entry to B_HOST state (HNP succeeded)
* once HNP succeeds, clear "ignore_disconnect" flag
* kick the root hub only _after_ the state is adjusted
Other state transitions are left alone. Notably, exit paths from
the "roles have switched" state ... A_PERIPHERAL handling of that
stays seriously broken.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup of OTG timer handling:
* unify decls for OTG time constants, in the core header
* set up and use that timer in a more normal way
* move to the driver struct, so it's usable outside core
And tighten use and setup of T(a_wait_bcon) so that if it's used,
it's always valid. (If that timer expires, the A-device will
stop powering VBUS. For non-OTG systems, that will be a surprise.)
No behavioral changes, other than more consistency when applying
that core HNP timeout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let the otg_transceiver in MUSB be managed by an external driver;
don't assume it's integrated. OMAP3 chips need it to be external,
and there may be ways to interact with the transceiver which add
functionality to the system.
Platform init code is responsible for setting up the transeciver,
probably using the NOP transceiver for integrated transceivers.
External ones will use whatever the board init code provided,
such as twl4030 or something more hands-off.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As DaVinci DM646x has a dedicated CPPI DMA interrupt, replace
cppi_completion() (which has always been kind of layering
violation) by a complete CPPI interrupt handler.
[ dbrownell@users.sourceforge.net: only cppi_dma.c needs platform
device header, not cppi_dma.h ]
Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As musb_advance_schedule() is now the only remaning
caller of musb_giveback() (and the only valid context
of such call), just fold the latter into the former
and then rename __musb_giveback() into musb_giveback().
This is a net minor shrink.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The argument for the 'is_in' parameter of musb_cleanup_urb()
is always extracted from an URB that's passed to the function.
So that parameter is superfluous; remove it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The existance of the scheduling list shouldn't matter in
determining whether there's currectly an URB executing on a
hardware endpoint. What should actually matter is the 'in_qh'
or 'out_qh' fields of the 'struct musb_hw_ep' -- those are
set in musb_start_urb() and cleared in musb_giveback() when
the endpoint's URB list drains. Hence we should be able to
replace the big *switch* statements in musb_urb_dequeue()
and musb_h_disable() with mere musb_ep_get_qh() calls...
While at it, do some more changes:
- add 'is_in' variable to musb_urb_dequeue();
- remove the unnecessary 'epnum' variable from musb_h_disable();
- fix the comment style in the vicinity.
This is a minor shrink of source and object code.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Factor out the often used code to get/set the active 'qh'
pointer for the hardware endpoint. Change the way the case
of a shared FIFO is handled by setting *both* 'in_qh' and
'out_qh' fields of 'struct musb_hw_ep'. That seems more
consistent and makes getting to the current 'qh' easy when
the code knows the direction beforehand.
While at it, turn some assignments into intializers and
fix declaration style in the vicinity.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor musb_save_toggle() as follows:
- replace 'struct musb_hw_ep *ep' parameter by 'struct
musb_qh *qh' to avoid re-calculating this value
- move usb_settogle() call out of the *if* operator.
This is a net minor shrink of source and object code.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Suppress "parasitic" endpoint interrupts in the DMA mode
when using CPPI DMA driver; they're caused by the MUSB gadget
driver using the DMA request mode 0 instead of the mode 1.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The gadget EP0 code routinely ignores an interrupt at end of
the data phase because of musb_g_ep0_giveback() resetting the
state machine to "idle, waiting for SETUP" phase prematurely.
The driver also prematurely leaves the status phase on
receiving the SetupEnd interrupt.
As there were still unhandled endpoint 0 interrupts happening
from time to time after fixing these issues, there turned to
be yet another culprit: two distinct gadget states collapsed
into one.
The (missing) state that comes after STATUS IN/OUT states was
typically indiscernible from them since the corresponding
interrupts tend to happen within too little period of time
(due to only a zero-length status packet in between) and so
they got coalesced; yet this state is not the same as the next
one which is associated with the reception of a SETUP packet.
Adding this extra state seems to have fixed the rest of the
unhandled interrupts that generic_interrupt() and
davinci_interrupt() hid by faking their result and only
emitting a debug message -- so, stop doing that.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix this build error when CONFIG_PM is not set:
drivers/usb/musb/musb_core.c:2232: error: 'musb_resume_early' undeclared here
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This email address is going to expire soon and my contribution to musb
is next to zero so remove it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During driver resume processing, musb could cause a kernel panic.
Fix by enabling the clock earlier, with the resume_early method.
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Multi-frame isochronous TX URBs transfers in DMA mode never
complete with CPPI DMA because musb_host_tx() doesn't restart
DMA on the second frame, only emitting a debug message.
With Inventra DMA they complete, but in PIO mode. To fix:
- Factor out programming of the DMA transfer from
musb_ep_program() into musb_tx_dma_program();
- Reorder the code at the end of musb_host_tx() to
facilitate the fallback to PIO iff DMA fails;
- Handle the buffer offset consistently for both
PIO and DMA modes;
- Add an argument to musb_ep_program() for the same
reason (it only worked correctly with non-zero
offset of the first frame in PIO mode);
- Set the completed isochronous frame descriptor's
'actual_length' and 'status' fields correctly in
DMA mode.
Also, since CPPI reportedly doesn't like sending isochronous
packets in the RNDIS mode, change the criterion for this
mode to be used only for multi-packet transfers. (There's
no need for that mode in the single-packet case anyway.)
[ dbrownell@users.sourceforge.net: split comment paragraph
into bullet list, shrink patch delta, style tweaks ]
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The MUSB code clears TXCSR_DMAMODE incorrectly in several
places, either asserting that TXCSR_DMAENAB is clear (when
sometimes it isn't) or clearing both bits together. Recent
versions of the programmer's guide require DMAENAB to be
cleared first, although some older ones didn't.
Fix this and while at it:
- In musb_gadget::txstate(), stop clearing the AUTOSET
and DMAMODE bits for the CPPI case since they never
get set anyway (the former bit is reserved on DaVinci);
but do clear the DMAENAB bit on the DMA error path.
- In musb_host::musb_ep_program(), remove the duplicate
DMA controller specific code code clearing the TXCSR
previous state, add the code to clear TXCSR DMA bits
on the Inventra DMA error path, to replace such code
(executed late) on the PIO path.
- In musbhsdma::dma_channel_abort()/dma_controller_irq(),
add/use the 'offset' variable to avoid MUSB_EP_OFFSET()
invocations on every RXCSR/TXCSR access.
[dbrownell@users.sourceforge.net: don't introduce CamelCase,
shrink diff]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We really want to use DMA mode 1 for all multi-packet transfers;
that's one IRQ on DMA completion, instead of one per packet.
There is an important issue with such transfers, especially on
the host side: when such transfers end with a full-size packet,
we must defer musb_dma_completion() calls until the FIFO empties.
Else we report URB completions too soon, and may clobber data in
the FIFO fifo when writing the next packet (losing data).
The Inventra DMA support uses DMA mode 1, but it ignores that
issue. The CPPI DMA support uses mode 0, but doesn't handle
its TXPKTRDY interrupts quite right either; it can get stale
"packet ready" interrupts, and report transfer completion too
early using slightly different code paths, also losing data.
So I'm solving it in a generic way -- by adding a sort of the
"interrupt filter" into musb_host_tx(), catching these cases
where a DMA completion IRQ doesn't suffice and removing some
needlessly controller-specific logic. When a TXDMA interrupt
happens and DMA request mode 1 is active, that filter resets
to mode 0 and defers URB completion processing until TXPKTRDY,
unless the FIFO is already empty. Related filtering logic in
Inventra and CPPI code gets removed.
Since it should be competely safe now to use the DMA request
mode 1 for host side transfers with the CPPI DMA controller,
set it in musb_h_tx_dma_start() ... now renamed (and shared).
[ dbrownell@users.sourceforge.net: don't introduce more
CamElCase; use more concise explanations ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The MUSB host side can't share generic TX FIFO flush logic
with EP0; the EP0 TX status register bits are different
from those for other entpoints.
Resolve this issue by providing a new EP0-specific routine
to flush and reset the FIFO, which pays careful attention to
restrictions listed in the latest programmer's guide. This
gets rid of an open issue whereby the usbtest control write
test (#14) failed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
