Add support for 802.1ad VLAN devices. This mainly consists of checking for
ETH_P_8021AD in addition to ETH_P_8021Q in a couple of places and check
offloading capabilities based on the used protocol.
Configuration is done using "ip link":
# ip link add link eth0 eth0.1000 \
type vlan proto 802.1ad id 1000
# ip link add link eth0.1000 eth0.1000.1000 \
type vlan proto 802.1q id 1000
52:54:00:12:34:56 > 92:b1:54:28:e4:8c, ethertype 802.1Q (0x8100), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
20.1.0.2 > 20.1.0.1: ICMP echo request, id 3003, seq 8, length 64
92:b1:54:28:e4:8c > 52:54:00:12:34:56, ethertype 802.1Q-QinQ (0x88a8), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 47944, offset 0, flags [none], proto ICMP (1), length 84)
20.1.0.1 > 20.1.0.2: ICMP echo reply, id 3003, seq 8, length 64
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows setting VXLAN destination to unicast address.
It allows that VXLAN can be used as peer-to-peer tunnel without
multicast.
v4: generalize struct vxlan_dev, "gaddr" is replaced with vxlan_rdst.
"GROUP" attribute is replaced with "REMOTE".
they are based by David Stevens's comments.
v3: move a new attribute REMOTE into the last of an enum list
based by Stephen Hemminger's comments.
v2: use a new attribute REMOTE instead of GROUP based by
Cong Wang's comments.
Signed-off-by: Atzm Watanabe <atzm@stratosphere.co.jp>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for IPv6 tokenized IIDs, that allow
for administrators to assign well-known host-part addresses
to nodes whilst still obtaining global network prefix from
Router Advertisements. It is currently in draft status.
The primary target for such support is server platforms
where addresses are usually manually configured, rather
than using DHCPv6 or SLAAC. By using tokenised identifiers,
hosts can still determine their network prefix by use of
SLAAC, but more readily be automatically renumbered should
their network prefix change. [...]
The disadvantage with static addresses is that they are
likely to require manual editing should the network prefix
in use change. If instead there were a method to only
manually configure the static identifier part of the IPv6
address, then the address could be automatically updated
when a new prefix was introduced, as described in [RFC4192]
for example. In such cases a DNS server might be
configured with such a tokenised interface identifier of
::53, and SLAAC would use the token in constructing the
interface address, using the advertised prefix. [...]
http://tools.ietf.org/html/draft-chown-6man-tokenised-ipv6-identifiers-02
The implementation is partially based on top of Mark K.
Thompson's proof of concept. However, it uses the Netlink
interface for configuration resp. data retrival, so that
it can be easily extended in future. Successfully tested
by myself.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
V3: make it a flag
V2: make the toggle per-port
Fast leave allows bridge to immediately stops the multicast
traffic on the port receives IGMP Leave when IGMP snooping is enabled,
no timeouts are observed.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
This patch provides extensions to VXLAN for supporting Distributed
Overlay Virtual Ethernet (DOVE) networks. The patch includes:
+ a dove flag per VXLAN device to enable DOVE extensions
+ ARP reduction, whereby a bridge-connected VXLAN tunnel endpoint
answers ARP requests from the local bridge on behalf of
remote DOVE clients
+ route short-circuiting (aka L3 switching). Known destination IP
addresses use the corresponding destination MAC address for
switching rather than going to a (possibly remote) router first.
+ netlink notification messages for forwarding table and L3 switching
misses
Changes since v2
- combined bools into "u32 flags"
- replaced loop with !is_zero_ether_addr()
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is Linux bridge implementation of root port guard.
If BPDU is received from a leaf (edge) port, it should not
be elected as root port.
Why would you want to do this?
If using STP on a bridge and the downstream bridges are not fully
trusted; this prevents a hostile guest for rerouting traffic.
Why not just use netfilter?
Netfilter does not track of follow spanning tree decisions.
It would be difficult and error prone to try and mirror STP
resolution in netfilter module.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is Linux bridge implementation of STP protection
(Cisco BPDU guard/Juniper BPDU block). BPDU block disables
the bridge port if a STP BPDU packet is received.
Why would you want to do this?
If running Spanning Tree on bridge, hostile devices on the network
may send BPDU and cause network failure. Enabling bpdu block
will detect and stop this.
How to recover the port?
The port will be restarted if link is brought down, or
removed and reattached. For example:
# ip li set dev eth0 down; ip li set dev eth0 up
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose bridge port parameter over netlink. By switching to a nested
message, this can be used for other bridge parameters.
This changes IFLA_PROTINFO attribute from one byte to a full nested
set of attributes. This is safe for application interface because the
old message used IFLA_PROTINFO and new one uses
IFLA_PROTINFO | NLA_F_NESTED.
The code adapts to old format requests, and therefore stays
compatible with user mode RSTP daemon. Since the type field
for nested and unnested attributes are different, and the old
code in libnetlink doesn't do the mask, it is also safe to use
with old versions of bridge monitor command.
Note: although mode is only a boolean, treating it as a
full byte since in the future someone will probably want to add more
values (like macvlan has).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
