ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer rxd is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'rxb' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit bf8f6952a2 ("Add blurb about RGMII") it was unclear
whose responsibility it was to insert the required clock skew, and
in hindsight, some PHY drivers got it wrong. The solution forward
is to introduce a new property, explicitly requiring skew from the
node to which it is attached. In the interim, this driver will handle
all 4 RGMII modes identically (no skew).
Fixes: 52dfc83012 ("net: ethernet: add driver for Aurora VLSI NB8800 Ethernet controller")
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: c7dfe3abf4 ("net: ethernet: nb8800: support fixed-link DT
node")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENODEV from the of_phy_connect() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ $ modinfo drivers/net/ethernet/aurora/nb8800.ko | grep alias
$
After this patch:
$ modinfo drivers/net/ethernet/aurora/nb8800.ko | grep alias
alias: of:N*T*Csigma,smp8734-ethernetC*
alias: of:N*T*Csigma,smp8734-ethernet
alias: of:N*T*Csigma,smp8642-ethernetC*
alias: of:N*T*Csigma,smp8642-ethernet
alias: of:N*T*Caurora,nb8800C*
alias: of:N*T*Caurora,nb8800
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ops->reset() error handling case, clk_disable_unprepare() is missed
before return from this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case nb8800_receive() fails to allocate a fragment, we would leak the
SKB freshly allocated and just return, instead, free it.
Reported-by: coverity (CID 1341750)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some circumstances, e.g. when connecting to a switch, the ethernet
port will not be connected to a PHY. In that case a "fixed-link" DT node
can be used to replace it.
https://stackoverflow.com/questions/31046172/device-tree-for-phy-less-connection-to-a-dsa-switch
This patch adds support for the "fixed-link" node to the nb8800 driver.
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Acked-by: Mans Rullgard <mans@mansr.com>
Cc: Mason <slash.tmp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nb8800_poll() function initializes the 'next' variable in the
loop looking for new input data. We know this will be called at
least once because 'budget' is a guaranteed to be a positive number
when we enter the function, but the compiler doesn't know that
and warns when the variable is used later:
drivers/net/ethernet/aurora/nb8800.c: In function 'nb8800_poll':
drivers/net/ethernet/aurora/nb8800.c:350:21: warning: 'next' may be used uninitialized in this function [-Wmaybe-uninitialized]
Changing the 'while() {}' loop to 'do {} while()' makes it obvious
to the compiler what is going on so it no longer warns.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a driver for the Aurora VLSI NB8800 Ethernet controller.
It is an almost complete rewrite of a driver originally found in
a Sigma Designs 2.6.22 tree.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
