Squash mt76u_buf_alloc_sg and mt76u_buf_alloc and remove duplicated
code. Reuse mt76u_refill_rx in mt76u_buf_alloc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76u_fill_bulk_urb to initialize tx/rx urbs and
remove duplicate code
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix following static checker warning in mt76u_buf_free:
drivers/net/wireless/mediatek/mt76/usb.c:372 mt76u_buf_free()
warn: address of 'urb->sg[i]' is non-NULL
There is no need to check sg page pointer since urb->num_sgs
has been already validated in mt76u_fill_rx_sg
Fixes: cb83585e11 ("mt76: usb: fix possible memory leak in mt76u_buf_free")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use usb_bulk_msg for reading MCU command responses. This simplify code
a lot.
Together with 97a3005759c ("mt76usb: allow mt76u_bulk_msg be used
for reads") it also fix possible problems with rx data buffers
not being aligned and contained within single page. After doing
page_frag_alloc(1024) consecutive page_frag_alloc(PAGE_SIZE) will
alloc PAGE_SIZE buffer at PAGE_SIZE - 1024 offset.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend mt76u_bulk_msg() such it can be used for synchronous bulk reads.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It needs to be always enabled for 76x2 and conditionally enabled/disabled
for 76x0. Since mt76x2_mac_stop clears this bit, ensure that it is enabled
in mt76x02_edcca_init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ED/CCA needs to be disable before stopping the MAC to avoid hangs from tx
being blocked. It must only be enabled again after the MAC has been started
again.
In many places this wasn't done properly, so fix this by always clearing
the relevant ED/CCA bits in mt76x2_mac_stop and set it up again after
channel change or calibration is done
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MCU request timeout usually indicates that the device is no longer responsive,
and it usually does not recover without a reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the timer is already running, there is no need to reset the counter,
because the drift will remain the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When mt76x0 and mt76x2 beacon code was unified, it changed the order in which
beacon enable and beacon interval are configured.
Configuring beacon enable before beacon interval can in some cases cause
problems with the beacon timer, leading to clients not waking up properly
from powersave mode.
Fix this by changing the order back to interval first, then enable.
Fixes: cc726268e4 ("mt76: move mt76x02_bss_info_changed in mt76x02-lib module")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check the count before incrementing it to match vendor code behavior.
This defers the adjustment by one more tick, which should improve accuracy
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT_BEACON_TIME_CFG_SYNC_MODE needs to be set for AP mode, according to the
documentation. For other modes it should be irrelevant in this case.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It needs to be unset instead of set
Fixes: 2340523646 ("mt76: fix transmission of encrypted management frames")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since ccmp_pn is u8 *, the second half needs to start at array index 4
instead of 0. Fixes a connection stall after a certain amount of traffic
Fixes: 2340523646 ("mt76: fix transmission of encrypted management frames")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove bogus check for MT_PACKET_ID_NO_ACK in mt76_tx_status_skb_get, which
is already handled in callers and turns timeout calls into no-ops
Do not clean up pending status items on reordering of tx status information
if the timeout is not reached yet
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_init_stream_cap() and mt76_get_txpower() call __sw_hweight8()
directly, but that's only defined if CONFIG_GENERIC_HWEIGHT is
enabled. The function that works on all architectures is hweight8().
Fixes: 551e1ef4d2 ("mt76: add mt76_init_stream_cap routine")
Fixes: 9313faacbb ("mt76: move mt76x02_get_txpower to mt76 core")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In mt76x02u_skb_dma_info() pad is always non-zero. Patch removes
bogus check and add comments to the function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During device removal the driver can report multiple error messages.
Use dev_err_ratelimited instead of dev_err to display urb errors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add disable_usb_sg module parameter to disable scatter-gather on demand
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use linear fragment and not a single usb scatter-gather buffer in mt76u
{tx,rx} datapath if the usb controller has sg data length constraints
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not use scatter-gather buffers for mcu commands.
Introduce mt76u_buf_alloc and mt76u_buf_alloc_sg routines.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76u_check_sg routine in usb.c and introduce sg_en variable
in mt76_usb in order to check if scatter-gather is supported by
mt76u layer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move q->ndesc initialization before the for loop in mt76u_alloc_rx
since otherwise allocated urbs will not be freed in mt76u_buf_free
Double-check scatterlist pointer in mt76u_buf_free
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix possible NULL pointer dereference in mt76u_mcu_deinit routine that
can occur if initialization path fails before calling mt76u_mcu_init_rx
Fixes: ee676cd501 ("mt76: add driver code for MT76x2u based devices")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We don't need to send firmware data asynchronously, much simpler is just
use synchronous usb_bulk_msg().
Tested-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_init_txpower in order to initialize max_power per channel
at device bootstrap. Modify mt76x0_get_tx_power_per_rate and
mt76x0_get_power_info signature in order to compute tx power for
non-operating channels
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize target_power variable in mt76x0_phy_set_txpower in order to
report target_power in debugfs
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is no need to retun 0 in mt76_dma_attach(), so switch it to void.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x0u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x0u_probe and in mt76x0e_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2u_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x{0,2} alloc_device common code in mt76_alloc_device and
remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Block only when the busy time reaches 92%, as lower values can be reached with
heavy 802.11 traffic as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Based on system load and time needed by other calibration runs, the time
between dev->mac_work runs can vary quite a bit.
Calculate busy time based on the actual time difference in order to avoid
potentially over-estimating busy time, which could lead to unnecessary tx
blocking.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Software encrypted packets can be passed not just through the drv_tx callback,
but also through the intermediate tx queue.
In order to deal with that, move the override to mt76x02_mac_write_txwi and
also take care of filling in the per-packet rate information
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove add_buf function pointer in mt76_queue_ops data structure since
it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_dma_tx_queue_skb_raw routine in dma.c and add the
corresponding entry in mt76_queue_ops data structure.
mt76_dma_tx_queue_skb_raw will be reused adding support for
mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove useless commented out configuration in mt76x0u_load_firmware
routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_rx_event i mt76-core module and remove duplicated code.
mt76_mcu_rx_event will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_get_response in mt76-core module and remove duplicated
code. mt76_mcu_get_response will be reused adding support for mt7603
driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_msg_alloc in mt76-core module and remove duplicated code.
mt76_mcu_msg_alloc will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix rate power configuration for VHT mcs 8 and 9 in
mt76x0_get_tx_power_per_rate. Moreover use the rate power
offset used for HT/VHT mcs 6 even for HT/VHT mcs 7
Fixes: b37bbc8c82 ("mt76x0: remove eeprom dependency from mt76x0_set_tx_power_per_rate")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
