For the Asus 1101HA, reporting position by reading the DMA position
buffer map seems unstable and often wrong. The reporter says that
position_fix=LPIB works much better (although not 100%, but this is
probably due to other issues).
The controller chip is an Intel Poulsbo 8086:811b (rev 07) controller,
and complete alsa-info is available here:
https://launchpadlibrarian.net/86691768/alsa-info.txt.1TNwyE5Ea7
Cc: stable@kernel.org (3.0+)
BugLink: http://bugs.launchpad.net/bugs/825709
Tested-by: Stefano Lodi
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This quirk sould be reverted. It has the following probems:
1) The quirk was intended to "ASUS MV2-MX SE" motherboards only, but the
ID used matches a much broader range, potentially all boards containing a
VIA chipset model in the family of vendor VIA 0x1106 and audio device ID
0x3288, which encompasses VIA-VT82xx, VIA-VT1xx and VIA-VT20xx chipsets.
2) VIA chipsets rely on azx_via_get_position() to handle correctly dma
transfers during capture. Using POS_FIX_LPIB instead of POS_FIX_VIACOMBO
leads to partially corrupted input buffers during capture. The effects
of this bug are not immediately visible, it took strong DSP expertise,
some expensive signal generator and a spectrum analyzer to identify it
and verify correct behaviour using original default.
3) It's almost certain that the quirk did not fix the real problem,
if there was one. Refer to original submission:
http://mailman.alsa-project.org/pipermail/alsa-devel/2010-February/025109.html
Signed-of-by: Marc Vertes <mvertes@sigfox.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the driver supports up to 10 streams. This is a restriction in
hda_intel.c and hda_codec.c: in the former, the fixed array size limits
the amount, and in the latter, the fixed device-number assignment table
(in get_empty_pcm_device()) limits the possibility.
This patch reduces the restriction by
- using linked list for managing PCM instances in hda_intel.c, and
- assigning non-fixed device numbers for the extra devices
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The regression-fix in 3.1 for the check of DMA-position validity caused
yet another regression for CA0110. As usual, this hardware seems working
only with LPIB properly. Adding the appropriate driver-caps bit to force
LPIB fixes the problem.
Reported-and-tested-by: Andres Freund <andres@anarazel.de>
Cc: <stable@kernel.org> [v3.1]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous fix for the position-buffer check gives yet another
regression on a Dell laptop. The safest fix right now is to add a
static quirk for this device (and better to apply it for stable
kernels too).
Reported-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit ef18beded8 introduced a
mechanism to assign the previously used slot for the next reopen of a
PCM stream. But the PCM device number isn't always unique (it may
have multiple substreams), and also the code doesn't check the stream
direction, thus both playback and capture streams share the same
device number.
For avoiding this conflict, make a unique key for each substream and
store/check this value at reopening.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit a810364a04
ALSA: hda - Handle -1 as invalid position, too
caused a regression on some machines that require the position-buffer
instead of LPIB, e.g. resulting in noises with mic recording with
PulseAudio.
This patch fixes the detection by delaying the test at the timing as
same as 3.0, i.e. doing the position check only when requested in
azx_position_ok().
Reported-and-tested-by: Rocko Requin <rockorequin@hotmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new option "snoop" for the traffic control of the HD-audio
controller chip. When set to 0, the non-snooping mode is used with
the traffic control bit is set in each stream control register.
This may allow better operations in the low power mode, but the actual
implementation is depending pretty much on the chipset.
As already implemented, more or less each chipset has own snoop-control
register bit. Now this setup refers to the snoop option, too.
Also, a new VIA chipset may require the non-snooping mode when set so
in BIOS. In such a case, the option value is overridden.
As default, it's still set to snoop=1 for keeping the same behavior as
before. In near future, it'll be set to 0 as default after checking
it works in every system well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new parameter to disable rounding of buffer/period sizes to
multiples of 128 bytes. This is more efficient in terms of memory
access but isn't required by the HDA spec and prevents users from
specifying exact period/buffer sizes. For example for 44.1kHz, a
period size set to 20ms will be rounded to 19.59ms.
Tested and enabled on Intel HDA controllers. Option is disabled by
default for other controllers.
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a Kconfig entry to specify the default buffer size.
Distros using PulseAudio can choose a larger value here.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that we have changed the position_fix default for ATI and AMD
to be LPIB (see commit 50e3bbf989), we can remove the quirks that
were added for ATI chipsets.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The name argument of request_irq() appears in /proc/interrupts, and
it's quite ugly when the name entry contains a space or special letters.
In general, it's simpler and more readable when the module name appears
there, so let's replace all entries with KBUILD_MODNAME.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The convention for pci_driver.name entry in kernel drivers seem to be
the module name or equivalent ones. But, so far, almost all PCI sound
drivers use more verbose name like "ABC Xyz (12)", and these are fairly
confusing when appearing as a file name.
This patch converts the all pci_driver.name entries in sound/pci/* to
use KBUILD_MODNAME for more unified appearance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SSYNC register was once defined as 0x34-37 in the old Intel datasheet,
but corrected later to 0x38-3b. For fixing the register usage, a new
bit-flag is introduced for indicating the old ICH SSYNC register, and
ICH* PCI entries are added explicitly to enable this quirk.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of checking the azx_dev index with a fixed number (4), check
the stream direction of the assigned substream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When reading from the position-buffer results in -1, handle as it's
invalid and falls back to LPIB mode as well as 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the data that backs the kcontrols created by
snd_hda_create_spdif_out_ctls is stored directly in struct hda_codec. When
multiple sets of these controls are stored, they will all manipulate the
same data, causing confusion. Instead, store an array of this data, one
copy per converter, to isolate the controls.
This patch would cause a behavioural change in the case where
snd_hda_create_spdif_out_ctls was called multiple times for a single codec.
As best I can tell, this is never the case for any codec.
This will be relevant at least for some HDMI audio codecs, such as the
NVIDIA GeForce 520 and Intel Ibex Peak. A future change will modify the
driver's handling of those codecs to create multiple PCMs per codec. Note
that this issue isn't affected by whether one creates a PCM-per-converter
or PCM-per-pin; there are multiple of both within a single codec in both
of those codecs.
Note that those codecs don't currently create multiple PCMs for the codec
due to the default HW mux state of all pins being to point at the same
converter, hence there is only a single converter routed to any pin, and
hence only a single PCM.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 9477c58e33 ("ALSA: hda - Reorganize controller quriks with bit
flags") changed the driver type compares into various quirk bits.
However, the check for AZX_DCAPS_NO_TCSEL got reverted: instead of
clearing TCSEL for chipsets that have that standard capability, it
cleared then when the NO_TCSEL bit was set.
This can lead to noise and repeated sounds - a weird "echo" behavior.
As the comment just above says: "Ensuring these bits are 0 clears
playback static on some HD Audio codecs". Which is definitely true at
least on my Core i5 Westmere system.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce bit-flags indicating the necessary controller quirks, and
set them in pci driver_data field. This simplifies the checks in the
driver code and avoids the pci-id lookup in different places.
Also, this patch adds the PCI ID entry for AMD Hudson. AMD Hudson
requires a similar workaround like ATI SB while other generic ATI and
AMD controllers don't need but some ATI-HDMI quirks. So, we need a
different entry for Hudson.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI and AMD chipsets seem not providing the proper position-buffer
information, and it also doesn't provide FIFO register required by
VIACOMBO fix. It's better to use LPIB for these.
Reported-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 447ee6a7cb.
The workaround introduced by this commit seems bogus.
The AMD chipsets don't provide proper position-buffer nor FIFO value
required by VIACOMBO fix.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AMD Hudson controllers give noisy outputs when the buffer data is
rewritten on the fly as PulseAudio does. This seems fixed by the
snoop bit enabled just like ATI chipset.
Also, disable 64bit DMA as now, to be sure.
We can revisit this later.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AMD chipsets often behave pretty badly regarding the DMA position
reporting. It results in the bad quality audio recording.
Using position_fix=3 works well in general for them, so let's enable
it as default for AMD.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The workaround for AMD chipset via sync_write flag seems needed for
machines with Realtek codecs. So, it's better to activate it
generically in hda_intel.c from the beginning.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Controller DeviceIDs for the Intel Panther Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
azx_init_pci() always writes PCI config register ICH6_PCIREG_TCSEL
although this looks to be only defined on Intel systems and has a
different meaning on AMD systems. On AMD systems the PCI interrupt pin
control register is modified instead.
Since the meaning of offset 0x44 in device specific configuration space is
unknown for devices by other vendors, we only exclude AMD systems to
retain the current behaviour.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bug reporter claims that position_fix=1 is needed for his
microphone to work. The controller PCI vendor-id is [1002:4383] (rev 40).
Reported-by: Kjell L.
BugLink: http://bugs.launchpad.net/bugs/718402
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an empty string is passed to patch option, the driver should
ignore it. Otherwise it gets an error by trying to load it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the new PCI ID 0x15ad and device ID 0x1977 for VMware HDAudio
Controller.
[changed to use AZX_DRIVER_GENERIC by tiwai]
Signed-off-by: Bankim Bhavsar <bbhavsar@vmware.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sjoerd Simons reports that, without using position_fix=1, recording
experiences overruns. Work around that by applying the LPIB quirk
for his hardware.
Reported-and-tested-by: Sjoerd Simons <sjoerd@debian.org>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/685161
The reporter of the bug states that he must use position_fix=1 to enable
capture for the internal microphone, so set it for his machine's PCI
SSID. Verified using 2.6.35 and the 2010-12-04 alsa-driver build.
Reported-and-tested-by: Ralph Wabel <rwabel@gmx.net>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Creative IBG controllers require the playback stream-tags to be started
from 1, instead of capture+1. Otherwise the stream stalls.
Reported-by: Wai Yew CHAY <wychay@ctl.creative.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Creative HD-audio controller chips require some workarounds:
- Additional delay before RIRB response
- Set the initial RIRB counter to 0xc0
The latter seems to be done in general in Windows driver, so we may
use this value later for all types if it's confirmed to work better.
Reported-by: Wai Yew CHAY <wychay@ctl.creative.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
What was previously known as via_dmapos_patch, and hard-coded to be
used for VIA and ATI controllers, is now configurable through a module
option. The background is that some VIA controllers seem to prefer
via_dmapos_patch to be turned off.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most of Intel controllers work as generic HD-audio without quirks,
and it'll be hopefully so in future. Let's mark pci id with the
PCI_CLASS_MULTIMEDIA_HD_AUDIO for Intel so that the driver will work
with any new control chips in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, we reset the converter setups like the stream-tag, the
channel-id and format-id in prepare callbacks, and clear them in
cleanup callbacks. This often causes a silence of the digital
receiver for a couple of seconds.
This patch tries to delay the converter setup changes as much as
possible. The converter setups are cached and aren't reset as long
as the same values are used. At suspend/resume, they are cleared
to be recovered properly, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the pending periods are often bogus and take long time until
actually processed, it often results in a high CPU usage of the hd-audio
workq. Overall it's better to have low CPU consumption by avoiding a
too tight loop rather than the wake-up timing accuracy.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set bit 15 (Stream Type) of HDA Stream Format to 1 (Non-PCM) when IEC958
channel status bit 1 (AES0 & 0x02) is set to 1 (non-audio).
This is a prequisite for HDMI HBR passthrough.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes thinko introduced in "last minutes" before commiting
of the last wallclk patch.
It also fixes the condition checking if the first period after last
wallclk update is processed. There is a little rounding error in
period_wallclk.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
BugLink: https://launchpad.net/bugs/587546
Symptom: On the reporter's ASUS M2V, using PulseAudio in Ubuntu 10.04 LTS
results in the PA daemon crashing shortly after attempting playback of an
audio file.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, attempt playback of an audio file while PulseAudio is
active.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: D Tangman
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/580749
Symptom: on the original reporter's VIA VT1708-based board, the
PulseAudio daemon dies shortly after the user attempts to play an audio
file.
Test case: boot from Ubuntu 10.04 LTS live cd; attempt to play an audio
file.
Resolution: add SSID for the original reporter's hardware to the
position_fix quirk table, explicitly specifying the LPIB method.
Reported-and-Tested-By: Harald
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/465942
Symptom: On the reporter's ASUS device, using PulseAudio in Ubuntu 10.04
LTS results in the PA daemon crashing shortly after attempting to select
capture or to configure the audio hardware profile.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's capture volume with PulseAudio.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Irihapeti
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/551949
Symptom: On the reporter's Shuttle device, using PulseAudio in Ubuntu
10.04 LTS results in "popping clicking" audio with the PA crashing
shortly thereafter.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's volume with PulseAudio.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Christian Mehlis <mehlis@inf.fu-berlin.de>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/586347
Symptom: On the Sony VPCS11V9E, using GStreamer-based applications with
PulseAudio in Ubuntu 10.04 LTS results in stuttering audio. It appears
to worsen with increased I/O.
Test case: use Rhythmbox under increased I/O pressure. This symptom is
reproducible in the current daily stable alsa-driver snapshots (at least
up until 21 May 2010; later snapshots fail to build from source due to
missing preprocessor directives when compiled against 2.6.32).
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Lauri Kainulainen <lauri@sokkelo.net>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check that the interrupt raised for a stream is actually a buffer
completion interrupt before handling it as one. Otherwise, memory
errors or FIFO xruns would be interpreted as a pointer update and could
break the stream timing.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/549560
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile)
Resolution: add SSID for Toshiba A100-259 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
This patch also trivially sorts the quirk table in ascending order by
subsystem vendor.
Reported-and-Tested-by: <davide.molteni@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/583983
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile).
Resolution: add SSID for Acer Aspire 5110 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
Reported-and-Tested-By: Leo
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add back the zero return value (activate workqueue) when
bdl_pos_adj is nonzero for position check.
Do the position related check only for first next period
using wallclk counter.
Return -1 value (ignore interrupt) when period_bytes
variable is zero.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use 24Mhz WALLCLK register to ignore too early interrupts and
wrong interrupt status. The bad timing confuses the higher ALSA
layer and causes audio skipping. More information about behaviour
and debugging can be found in kernel bz#15912.
https://bugzilla.kernel.org/show_bug.cgi?id=15912
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The HDA controller in US15W (Poulsbo) reports inaccurate position values
for capture streams when using the LPIB read method, resulting in
distorted recordings.
However, using the position buffer is broken for playback streams,
resulting in a fallback to the LPIB method with the current driver.
This patch works around the issue by independently detecting the read
position method for capture and playback streams.
The patch will not have any effect if the position fix method is
explicitly set.
[Code simplified by tiwai]
Signed-off-by: Shahin Ghazinouri <shahin.ghazinouri@pelagicore.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/459083
The OR has verified with 2.6.32.11 and the latest alsa-driver stable
daily snapshot that position_fix=1 is necessary for the external mic
to work and for PulseAudio not to crash constantly.
This patch is necessary also for 2.6.32.11 and 2.6.33.2.
Reported-by: <imwithid@yahoo.com>
Tested-by: <imwithid@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Biostar mobo seems to give a wrong DMA position, resulting in
stuttering or skipping sounds on 2.6.34. Since the commit
7b3a177b0d, "ALSA: pcm_lib: fix "something
must be really wrong" condition", makes the position check more strictly,
the DMA position problem is revealed more clearly now.
The fix is to use only LPIB for obtaining the position, i.e. passing
position_fix=1. This patch adds a static quirk to achieve it as default.
Reported-by: Frank Griffin <ftg@roadrunner.com>
Cc: Eric Piel <Eric.Piel@tremplin-utc.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device needs MSI disablement. Added to the quirk list.
Reported-by: Harald Dunkel <harri@afaics.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=575669
The OR states that position_fix=1 is necessary to work around glitching
during volume adjustments using PulseAudio.
Reported-by: Carlos Laviola <claviola@debian.org>
Tested-by: Carlos Laviola <claviola@debian.org>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The probe_only module parameter skips the codec initialization, too.
Remove the model=hwio code and use second bit in probe_only to
skip the HDA codec reset procedure.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Using the 'model=hwio' option, the driver bypasses any codec
initialization and the reset procedure for codecs is also
bypassed. This mode is usefull to enable direct access using
hwdep interface (using hdaverb or hda-analyzer tools) and
retain codec setup from BIOS.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
BugLink: https://bugs.launchpad.net/bugs/538895
The OR has verified that both position_fix=1 and model=6stack-dig are
necessary to have capture function properly. (The existing 3stack-6ch
model quirk seems to be incorrect.)
Reported-by: Reuben Bailey <reuben.e.bailey@gmail.com>
Tested-by: Reuben Bailey <reuben.e.bailey@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Judging from the member of enable_msi white-list, Nvidia controller
seems to cause troubles with MSI enabled, e.g. boot hang up or other
serious issue may come up. It's safer to disable MSI as default for
Nvidia controllers again for now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
without the following patch audio ssttuutteerrs on
ASUS M2N32-SLI PREMIUM ACPI BIOS Revision 1304
the sound device is:
00:0e.1 Audio device: nVidia Corporation MCP55 High Definition Audio (rev a2)
worked with 2.6.32
Signed-off-by: Ralf Gerbig <rge@quengel.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/523953
The OR has verified that position_fix=1 is necessary to work around
errors on his machine.
Reported-by: MMarking
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/530346
The OR has verified that position_fix=1 is necessary to work around
errors on his machine.
Reported-by: Tom Louwrier
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Support max codecs to 8 for nvidia hda controller.
Change AZX_MAX_CODECS to 8, and add
"#define AZX_DEFAULT_CODECS 4" for default driver.
Set azx_max_codecs to 8 for nvidia controller.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables snoop, eliminating static during playback.
This patch supersedes the previous Cougar Point audio patch.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With PulseAudio and an application accessing an input device like `gnome-volume-manager` both have high CPU load as reported in [1].
Loading `snd-hda-intel` with `position_fix=1` fixes this issue. Therefore add a quirk for ASUS M2V-MX SE.
The only downside is, when now exiting for example MPlayer when it is playing an audio file a high pitched sound is outputted by the speaker.
$ lspci -vvnn | grep -A10 Audio
20:01.0 Audio device [0403]: VIA Technologies, Inc. VT1708/A [Azalia HDAC] (VIA High Definition Audio Controller) [1106:3288] (rev 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:8290]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbffc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
[1] http://sourceforge.net/mailarchive/forum.php?thread_name=1265550675.4642.24.camel%40mattotaupa&forum_name=alsa-user
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The MSI blacklist entry for ASUS mobo added in the commit
8ce28d6abf was based on the alsa-info
output wrongly posted. Fix the id to the right one now.
Reported-by: Sid Boyce <sboyce@blueyonder.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the zero-division warning message with WARN_ON_ONCE() per the
advice by Linus. This shouldn't happen, but if it happens, it's
possible that the bug happens often due to buggy IRQs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On my AMD780V chipset, hda_intel.c can crash the kernel with a divide by
zero
for as-yet unknown reasons. A simple check for zero prevents it, though
the problem that causes it remains. Since the workaround is harmless and
won't affect anyone except victims of this bug, it should be safe;
moreover,
because this crash can be triggered by a user-mode application, there are
denial of service implications on the systems affected by the bug without
the patch.
Signed-off-by: Jody Bruchon <jody@nctritech.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This renames the interrupt name in /proc/interrupt.
HDA Intel -> hda_intel
This also eliminates space from the name, probably helping some
parsers.
Don't think anybody depends on this name in userspace
Signed-off-by: Takashi Iwai <tiwai@suse.de>
My sound codec seems sometimes (very rarely) to omit interrupts (ALC268)
However, interrupt mode still works.
Thus if we get timeout, poll the codec once.
If we get 3 such polls in a row, then switch to polling mode.
This patch is maybe an bandaid, but this might be a workaround for hardware bug.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In hda_codec.c, it has define
"[HDA_PCM_TYPE_HDMI] = { 3, 7, 8, 9, -1 },",
it support up to device 9 for HDMI.
But in hda_intel.c, it only define AZX_MAX_PCMS as 8.
So if it have 4 hdmi codecs, when run azx_attach_pcm_stream(),
it will show error "Invalid PCM device number 8", and "... number 9",
and return "-EINVAL".
We should change the AZX_MAX_PCMS to 10.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sid Boyce reported that his machine locks up without enable_msi=0 option.
This looks like another ASUS mobo with Nvidia combo.
Reported-by: Sid Boyce <sboyce@blueyonder.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In azx_stream_start() and azx_stream_stop(),
it use azx_readb/azx_writeb to read/write SIE,
it just enable/disable 8 streams.
But according to the HDA spec, it support 30 streams,
and the new HDA controller will support more then 8
streams. So we should use azx_readl/azx_writel to
read/write SIE.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the Intel Cougar Point (PCH) HD Audio Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we run the following commands in turn (with
CONFIG_SND_HDA_POWER_SAVE_DEFAULT=0),
speaker-test -Dhw:0,3 -c2 -twav # HDMI
speaker-test -Dhw:0,0 -c2 -twav # Analog
The second command will produce sound in the analog lineout _as well as_
HDMI sink. The root cause is, device 0 "reuses" the same stream tag that
was used by device 3, and the "intelhdmi - sticky stream id" patch leaves
the HDMI codec in a functional state. So the HDMI codec happily accepts
the audio samples which reuse its stream tag.
The proposed solution is to remember the last device each azx_dev was
assigned to, and prefer to
1) reuse the azx_dev (and hence the stream tag) the HDMI codec last used
2) or assign a never-used azx_dev for HDMI
With this patch and the above two speaker-test commands,
HDMI codec will use stream tag 8 and Analog codec will use 5.
The stream tag used by HDMI codec won't be reused by others, as long
as we don't run out of the 4 playback azx_dev's. The legacy Analog
codec will continue to use stream tag 5 because its device id is 0
(this is a bit tricky).
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A machine with AMD CPU with Nvidia board doesn't work with MSI.
Reported-by: Robert J. King <peritus@gurunetwork.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of listing all individual PCI IDs, check the matching with
the PCI class together with the vendor id for Nvidia.
This simplifies the pci id entries.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For codecs without EPSS support (G45/IbexPeak), the hotplug event will
be lost if the HDA is powered off during the time. After that the pin
presence detection verb returns inaccurate info.
So always power-on HDA link for !EPSS codecs.
KarL offers the fact and Takashi recommends to flag hda_bus. Thanks!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Confirmed from vendor and tests in RedHat bugzilla #536782 .
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The beep_mode parameter for snd-hda-intel module allows to choose among
different digital beep device registation to the input layer.
0 = do not register to the input layer
1 = register to the input layer all time
2 = use "Beep Switch" control exported to user space mixer applications
Also, introduce CONFIG_SND_HDA_INPUT_BEEP_MODE for default value.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add reboot notifier to each codec so that it can do some workarounds
needed for reboot.
So far, patch_sigmatel.c calls its shutup routine for avoiding noises
at reboot on some HP machines.
References: Novell bnc#544779
http://bugzilla.novell.com/show_bug.cgi?id=544779
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, CORB/RIRB still remains even if the driver is switched to the
single_cmd mode. The specification says that this should be disabled,
but I hoped this isn't the case; indeed most devices worked together with
CORB/RIRB.
However, Poulsbo (US15W) seems problematic with this setup, and it
requires to disable CORB/RIRB when single_cmd is used.
Now this patch disables CORB/RIRB initialization when the single_cmd
mode is used. Also the unsolicited event is disabled because it can't
work without RIRB.
Reported-and-tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When any codec communication error happens, try to switch to the polling
mode first before turning off MSI. MSI gets more stable nowadays, thus
we should keep it on as much as possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent kernel can handle MSI properly on non-Intel platforms,
let's enable MSI as default.
If any borken device is found, we can add the quirk entry to the list,
which is currently empty.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Created a white-list to enable MSI since some devices require MSI
explicitly due to BIOS/ACPI problems. Simply using a quirk list.
As the first case, take HP Compaq CQ40.
Reference: Novell bnc#529971
https://bugzilla.novell.com/show_bug.cgi?id=529971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This converts the last CORBWP access outside of reg_lock.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just for safety. azx_init_cmd_io() and azx_free_cmd_io() may be
called when switching to single command mode.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that each codec will have its own module, it is possible
for the user to load one codec while another one is running.
So cmd_mutex would be a safe addition to probe_codec().
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we hit a bug in our dev board, whose HDMI codec#3 may emit
redundant/spurious responses, which were then taken as responses to
command for another onboard Realtek codec#2, and mess up both codecs.
Extend the azx_rb.cmds and azx_rb.res to array and track each codec's
commands/responses separately. This helps keep good codec safe from
broken ones.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for new AMD HD audio devices. Use generic driver to detect HD audio
devices with Vendor ID AMD.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA driver disabled HD audio 64bit address support for all AMD
SB600/SB700/SB800 platforms with commit
09240cf429 due to one SB600 issue
reported by community, but we do not see the similar issue on
SB700/SB800 platforms.
This patch is to refine the workaround for SB600 only.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add some sanity checks of struct snd_pcm_hardware fields in the PCM
open callback of hda driver. This makes a bit easier to debug any PCM
setup errors in the codec side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM rates bit field may have been changed by the codec open callback.
In that case, we need to reset rate_min and rate_max. So, simply call
snd_pcm_lib_hw_rates() again after the codec open callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the patch module option to apply a "patch" as a firmware to
modify pin configurations or give additional hints to the driver
before actually initializing and configuring the codec.
This can be used as a workaround when the BIOS doesn't give sufficient
information or give wrong information that doesn't match with the real
hardware setup, until it's fixed statically in the driver via a quirk.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The codec setup call via snd_hda_codec_configure() isn't necessarily
called in snd_hda_codec_new(). For the later added feature, it's better
to change the code flow like:
- create all codec instances
- configure each codec
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix this build error when CONFIG_PM is not set:
ound/pci/hda/hda_intel.c: In function 'azx_bus_reset':
sound/pci/hda/hda_intel.c:1270: error: implicit declaration of function 'snd_pcm_suspend_all'
sound/pci/hda/hda_intel.c:1271: error: implicit declaration of function 'snd_hda_suspend'
sound/pci/hda/hda_intel.c:1272: error: implicit declaration of function 'snd_hda_resume'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The reset of a BUS controller during operations is somehow risky and
shouldn't be done inevitably for devices that have apparently no such
codec-communication problems.
This patch adds the check of the hardware and limits the bus-reset
capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some machines machine cause a severe CORB/RIRB stall in certain
weird conditions, such as PA access at the start up together with
fglrx driver. This seems unable to be recovered without the controller
reset.
This patch allows the bus controller reset at critical errors so
that the communication gets recovered again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ICH6_GCTL_RESET was wrongly set to another bit by the commit
b21fadb9c1. This caused a problem when
the codec needs really a reset (e.g. recovering from the communication
error at probe).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added some missing register bits definitions to reduce magic numbers.
Also renamed some to follow the names on the datasheet.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the single_cmd mode, the hardware cannot store the multiple replies
like on RIRB, thus each verb has to sync and wait for the response no
matter whether the return value is needed or not. Otherwise it may
result in a wrong return value from the previous verb.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the single_cmd mode, the current driver code doesn't do any update
for RIRB just for any safety reason. But, actually the RIRB and
single_cmd mode don't conflict. Unsolicited events can be delivered
even while using the single_cmd mode.
This patch allows the handling of unsolicited events with single_cmd
mode, just always checking RIRB independent from single_cmd flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec communication error occurs, the CORB/RIRB counters should
be reset first before re-issuing the verb. Simply call azx_free_cmd_io()
and azx_init_cmd_io() to achieve that.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS W5Fm needs the fixed codec-slots to probe to override the BIOS
problem like W5F.
Tested-by: Alp Kılıç <kilic.alp@gmail.com>
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add proper prefix to each kernel message in hda_intel.c.
Also, avoid the unneeded prefix when CONFIG_SND_VERBOSE_PRINTK is used
together with snd_print*().
Reference: bko#13207
http://bugzilla.kernel.org/show_bug.cgi?id=13207
Signed-off-by: Takashi Iwai <tiwai@suse.de>
