The SystemACE driver does not handle an empty CF slot gracefully. An
empty CF slot ends up hanging the system. This patch adds a check for
the CF state and stops trying to process requests if the slot is empty.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Convert the PS3 Video RAM Storage Driver from an MTD driver to a plain block
device driver.
The ps3vram driver exposes unused video RAM on the PS3 as a block device
suitable for storage or swap. Fast data transfer is achieved using a local
cache in system RAM and DMA transfers via the GPU.
The new driver is ca. 50% faster for reading, and ca. 10% for writing.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
p54: fix race condition in memory management
cfg80211: test before subtraction on unsigned
iwlwifi: fix error flow in iwl*_pci_probe
rt2x00 : more devices to rt73usb.c
rt2x00 : more devices to rt2500usb.c
bonding: Fix device passed into ->ndo_neigh_setup().
vlan: Fix vlan-in-vlan crashes.
net: Fix missing dev->neigh_setup in register_netdevice().
tmspci: fix request_irq race
pkt_sched: act_police: Fix a rate estimator test.
tg3: Fix 5906 link problems
SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
IPv6: add "disable" module parameter support to ipv6.ko
sungem: another error printed one too early
aoe: error printed 1 too early
net pcmcia: worklimit reaches -1
net: more timeouts that reach -1
net: fix tokenring license
dm9601: new vendor/product IDs
netlink: invert error code in netlink_set_err()
...
Upon a 'transfer error block' size is set to -EINVAL, but this becomes positive
since size is unsigned: p->offset still gets incremented.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 5e4c91c84b forgot to remove the
initial sleep, get rid of it.
Thanks to Randy Dunlap <randy.dunlap@oracle.com> for spotting this error.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When booting Xen Dom0 on a pre-release 3.2.1 hypervisor the system Oopses on a
"Unable to handle kernel NULL pointer dereference" in xenwatch.
From the backtrace it looks like backend_changed is calling bdget_disk
with a NULL pointer. Checking for NULL and returning ENODEV instead
allows the kernel to boot.
with while (i-- > 0); i reaches -1 after the loop, so the test below is printed
one too early: 0 still means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On occasion, the request will apparently have more segments than we
fit into the ring. Jens says:
> The second problem is that the block layer then appears to create one
> too many segments, but from the dump it has rq->nr_phys_segments ==
> BLKIF_MAX_SEGMENTS_PER_REQUEST. I suspect the latter is due to
> xen-blkfront not handling the merging on its own. It should check that
> the new page doesn't form part of the previous page. The
> rq_for_each_segment() iterates all single bits in the request, not dma
> segments. The "easiest" way to do this is to call blk_rq_map_sg() and
> then iterate the mapped sg list. That will give you what you are
> looking for.
> Here's a test patch, compiles but otherwise untested. I spent more
> time figuring out how to enable XEN than to code it up, so YMMV!
> Probably the sg list wants to be put inside the ring and only
> initialized on allocation, then you can get rid of the sg on stack and
> sg_init_table() loop call in the function. I'll leave that, and the
> testing, to you.
[Moved sg array into info structure, and initialize once. -J]
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If reset_devices is set for kexec, then cciss will delay 30 seconds
since the old 5i controller _may_ need that long to recover. Replace
the long sleep with incremental sleep and tests to reduce the 30 seconds
to worst case for 5i, so that other controllers will proceed quickly.
Reviewed-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
http://kisskb.ellerman.id.au/kisskb/buildresult/72115/:
| net/mac80211/ieee80211_i.h:327: error: syntax error before 'volatile'
| net/mac80211/ieee80211_i.h:350: error: syntax error before '}' token
| net/mac80211/ieee80211_i.h:455: error: field 'sta' has incomplete type
| distcc[19430] ERROR: compile net/mac80211/main.c on sprygo/32 failed
This is caused by
| # define mfp ((*(volatile struct MFP*)MFP_BAS))
in arch/m68k/include/asm/atarihw.h, which conflicts with the new "mfp" enum in
net/mac80211/ieee80211_i.h.
Rename "mfp" to "st_mfp", as it's a way too generic name for a global #define.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: fix deadlock in blk_abort_queue() for drivers that readd to timeout list
block: fix booting from partitioned md array
block: revert part of 18ce3751cc
cciss: PCI power management reset for kexec
paride/pg.c: xs(): &&/|| confusion
fs/bio: bio_alloc_bioset: pass right object ptr to mempool_free
block: fix bad definition of BIO_RW_SYNC
bsg: Fix sense buffer bug in SG_IO
The floppy driver requests an I/O port it doesn't need, and sometimes this
causes a conflict with a motherboard device reported by PNPBIOS.
This patch makes the floppy driver request and release only the ports it
actually uses. It also factors out the request/release stuff and the
io-ports list so they're all in one place now.
The current floppy driver uses only these ports:
0x3f2 (FD_DOR)
0x3f4 (FD_STATUS)
0x3f5 (FD_DATA)
0x3f7 (FD_DCR/FD_DIR)
but it requests 0x3f2-0x3f5 and 0x3f7, which includes the unused port
0x3f3.
Some BIOSes report 0x3f3 as a motherboard resource. The PNP system driver
reserves that, which causes a conflict when the floppy driver requests
0x3f2-0x3f5 later.
Philippe reported that this conflict broke the floppy driver between
2.6.11 and 2.6.22. His PNPBIOS reports these devices:
$ cat 00:07/id 00:07/resources # motherboard device
PNP0c02
state = active
io 0x80-0x80
io 0x10-0x1f
io 0x22-0x3f
io 0x44-0x5f
io 0x90-0x9f
io 0xa2-0xbf
io 0x3f0-0x3f1
io 0x3f3-0x3f3
$ cat 00:03/id 00:03/resources # floppy device
PNP0700
state = active
io 0x3f4-0x3f5
io 0x3f2-0x3f2
Reference:
http://lkml.org/lkml/2009/1/31/162
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Reported-by: Philippe De Muyter <phdm@macqel.be>
Tested-by: Philippe De Muyter <phdm@macqel.be>
Cc: Adam M Belay <abelay@mit.edu>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Welland ME-747K-SI AoE target generates unsolicited AoE responses that
are marked as vendor extensions. Instead of ignoring these packets, the
aoe driver was generating kernel messages for each unrecognized response
received. This patch corrects the behavior.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Reported-by: <karaluh@karaluh.pl>
Tested-by: <karaluh@karaluh.pl>
Cc: <stable@kernel.org>
Cc: Alex Buell <alex.buell@munted.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kexec kernel resets the CCISS hardware in three steps:
1. Use PCI power management states to reset the controller in the
kexec kernel.
2. Clear the MSI/MSI-X bits in PCI configuration space so that MSI
initialization in the kexec kernel doesn't fail.
3. Use the CCISS "No-op" message to determine when the controller
firmware has recovered from the PCI PM reset.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix a problem that causes I/O to a disconnected (or partially initialized)
nbd device to hang indefinitely. To reproduce:
# ioctl NBD_SET_SIZE_BLOCKS /dev/nbd23 514048
# dd if=/dev/nbd23 of=/dev/null bs=4096 count=1
...hangs...
This can also occur when an nbd device loses its nbd-client/server
connection. Although we clear the queue of any outstanding I/Os after the
client/server connection fails, any additional I/Os that get queued later
will hang.
This bug may also be the problem reported in this bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=12277
Testing would need to be performed to determine if the two issues are the
same.
This problem was introduced by the new request handling thread code ("NBD:
allow nbd to be used locally", 3/2008), which entered into mainline around
2.6.25.
The fix, which is fairly simple, is to restore the check for lo->sock
being NULL in do_nbd_request. This causes I/O to an uninitialized nbd to
immediately fail with an I/O error, as it did prior to the introduction of
this bug.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Reported-by: Jon Nelson <jnelson-kernel-bugzilla@jamponi.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <stable@kernel.org> [2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two nbd-clients at same time are bad idea, and cause WARN_ON from nbd in
2.6.28-rc7 from sysfs_add_one. This simply prevents that from happening.
To reproduce:
cat /dev/zero | head -c 10000000 > /tmp/delme.fstest.fs
nbd-server 9100 -l /anyone.can.connect > /tmp/delme.fstest.fs &
sleep 1
nbd-client localhost 9100 /dev/nd0 &
nbd-client localhost 9100 /dev/nd0 &
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Apart from sleep_on() calls that could be easily converted to
wait_event() and completion calls amiflop also used a flag in ms_delay()
and ms_isr() as a custom mutex for ms_delay() without a need for
explicit unlocking. I converted that to a standard mutex.
The replacement for the unconditional sleep_on() in fd_motor_on() is a
complete_all() together with a INIT_COMPLETION() before the mod_timer()
call. It appears to me that fd_motor_on() might be called concurrently
and fd_select() does not guarantee mutual exclusivity in the case the
same drive gets selected again.
Signed-off-by: Andreas Bombe <aeb@debian.org>
Acked-by: Jörg Dorchain <joerg@dorchain.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add "xlnx,sysace" compatible string to the of_platform binding
table. Platforms which have the SysACE chip on board (e.g.
Katmai) instead of via a Xilinx generated IP core will use
this value in their device tree.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Work around branch tracer warning.
sparc64: Fix unsigned long long warnings in drivers.
sparc64: Use unsigned long long for u64.
sparc: refactor code in fault_32.c
sparc64: refactor code in init_64.c
sparc64: refactor code in viohs.c
sparc: make proces_ver_nack a bit more readable
This patch (as1161) changes the interface to
usb_lock_device_for_reset(). The existing interface is apparently not
very clear, judging from the fact that several of its callers don't
use it correctly. The new interface always returns 0 for success and
it always requires the caller to unlock the device afterward.
The new routine will not return immediately if it is called while the
driver's probe method is running. Instead it will wait until the
probe is over and the device has been unlocked. This shouldn't cause
any problems; I don't know of any cases where drivers call
usb_lock_device_for_reset() during probe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix warnings caused by the unsigned long long usage in sparc
specific drivers.
The drivers were considered sparc specific more or less from the
filename alone.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: struct device - replace bus_id with dev_name()
lguest: move the initial guest page table creation code to the host
kvm-s390: implement config_changed for virtio on s390
virtio_console: support console resizing
virtio: add PCI device release() function
virtio_blk: fix type warning
virtio: block: dynamic maximum segments
virtio: set max_segment_size and max_sectors to infinite.
virtio: avoid implicit use of Linux page size in balloon interface
virtio: hand virtio ring alignment as argument to vring_new_virtqueue
virtio: use KVM_S390_VIRTIO_RING_ALIGN instead of relying on pagesize
virtio: use LGUEST_VRING_ALIGN instead of relying on pagesize
virtio: Don't use PAGE_SIZE for vring alignment in virtio_pci.
virtio: rename 'pagesize' arg to vring_init/vring_size
virtio: Don't use PAGE_SIZE in virtio_pci.c
virtio: struct device - replace bus_id with dev_name(), dev_set_name()
virtio-pci queue allocation not page-aligned
Fix parameter type warning:
linux-next-20081126/drivers/block/virtio_blk.c:307: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Enhance the driver to handle whatever maximum segment number the host
tells us to handle. Do to this, we need to allocate the scatterlist
dynamically.
We set max_phys_segments and max_hw_segments to the same value (1 if
the host doesn't tell us, since that's safest and all known hosts do
tell us).
Note that kmalloc'ing the structure for large sg_elems might be
problematic: the fix for this is sg_table, but that requires more
work.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Setting max_segment_size allows more than 64k per sg element, unless
the host specified a limit. Setting max_sectors indicates that our
max_hw_segments is the only limit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Simplify parameters to deregister_disk function.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In loop_unplug() function is expected that mapping is set
and lo->lo_backing_file is not NULL.
Unfortunately loop_set_fd() set the request queue unplug function,
but loop_clr_fd() doesn't clear that.
Loop device allows open of non-configured loop in some situations.
If the unplug on request queue is called, loop module oopses because
of missing lo_backing_file.
Simple reproducer:
losetup /dev/loop0 /xxx
losetup -d /dev/loop0
dmsetup create x --table "0 1 linear /dev/loop0 0"
EIP is at loop_unplug+0x1d/0x3b
...
Call Trace:
blk_unplug+0x57/0x5e
dm_table_unplug_all+0x34/0x77 [dm_mod]
destroy_inode+0x27/0x38
generic_delete_inode+0xd5/0xd9
iput+0x4b/0x4e
dm_resume+0xca/0xfe [dm_mod]
dev_suspend+0x143/0x165 [dm_mod]
dm_ctl_ioctl+0x18e/0x1cf [dm_mod]
dev_suspend+0x0/0x165 [dm_mod]
dm_ctl_ioctl+0x0/0x1cf [dm_mod]
vfs_ioctl+0x22/0x69
do_vfs_ioctl+0x39d/0x3c7
trace_hardirqs_on+0xb/0xd
remove_vma+0x50/0x56
do_munmap+0x21c/0x237
sys_ioctl+0x2c/0x45
sysenter_do_call+0x12/0x31
Several reports here
http://www.kerneloops.org/search.php?search=loop_unplug
Fix it by simply clear unplug function together with
removing of backing file.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When there are still queued bios and reference count
drops to zero, loop device must flush all queued bios.
Otherwise it can lead to situation that caller
closes the device, but some bios are still running
and endio() function call later OOpses when uses
unallocated mempool.
This happens for example when running dm-crypt over loop,
here is typical oops backtrace:
Oops: 0000 [#1] PREEMPT SMP
EIP is at mempool_free+0x12/0x6b
...
crypt_dec_pending+0x50/0x54 [dm_crypt]
crypt_endio+0x9f/0xa7 [dm_crypt]
crypt_endio+0x0/0xa7 [dm_crypt]
bio_endio+0x2b/0x2e
loop_thread+0x37a/0x3b1
do_lo_send_aops+0x0/0x165
autoremove_wake_function+0x0/0x33
loop_thread+0x0/0x3b1
kthread+0x3b/0x61
kthread+0x0/0x61
kernel_thread_helper+0x7/0x10
(But crash is reproducible with different dm targets
running over loop device too.)
Patch fixes it by flushing the bios in release call,
reusing the flush mechanism for switching backing store.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This both cleans up the code and also helps detect the spurious case
of a command attempted being removed from a queue it doesn't belong
to.
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Xen's blkfront sets noop as the default I/O scheduler at initialization
time to avoid elevator overheads such as idling, but with the advent of
basic disk profiling capabilities this is not necessary anymore. We
should just tell the block layer that we are a paravirt front-end driver
and the elevator will automatically make the necessary adjustments.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
As a paravirt front-end driver, virtio_blk is not a rotational device so
we want do avoid idling in AS/CFQ. Tell the block layer about this.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
Fix problem that deleting multiple logical drives could cause a panic.
It fixes a panic which can be easily reproduced in the following way: Just
create several "arrays," each with multiple logical drives via hpacucli,
then delete the first array, and it will blow up in deregister_disk(), in
the call to get_host() when it tries to dig the hba pointer out of a NULL
queue pointer.
The problem has been present since my code to make rebuild_lun_table
behave better went in.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The pktcdvd created class devices only export some sysfs files,
but have no char dev_t registered in the driver.
At class device creation time they copy the dev_t value of the
block device to the char device, wich will register a new char
device in the driver core and userspace, with a conflicting dev_t
value.
In many cases the class devices dev_t just points to a random
USB device. This fixes the sysfs "duplicate entry" errors.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
final close of ->bdev should match the initial open, i.e.
get FMODE_READ | FMODE_NDELAY; FMODE_READ|FMODE_WRITE has
been a braino.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix system calls on Cell entered with XER.SO=1
powerpc/cell: Fix GDB watchpoints, again
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
powerpc/cell/axon-msi: Retry on missing interrupt
powerpc: Fix boot freeze on machine with empty memory node
powerpc: Fix IRQ assignment for some PCIe devices
powerpc/spufs: Fix spinning in spufs_ps_fault on signal
powerpc/mpc832x_rdb: fix swapped ethernet ids
powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
powerpc/85xx: L2 cache size wrong in 8572DS dts
powerpc/virtex: Update defconfigs
powerpc/52xx: update defconfigs
xsysace: Fix driver to use resource_size_t instead of unsigned long
powerpc/virtex: fix various format/casting printk mismatches
powerpc/mpc5200: fix bestcomm Kconfig dependencies
powerpc/44x: Fix 460EX/460GT machine check handling
powerpc/40x: Limit allocable DRAM during early mapping
Add %pm to omit the colons when printing a mac address.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings when CCISS_DEBUG is defined.
drivers/block/cciss.c:2856: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3205: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3236: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
drivers/block/cciss.c:3246: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should release old elevator when change to use a new one.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
