Update gcm(aes) descriptors (generic, rfc4106 and rfc4543) such that
they would also work when submitted via the QI interface.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Crypto drivers are expected to return -EBADMSG in case of
ICV check (authentication) failure.
In this case it also makes sense to suppress the error message
in the QI dequeue callback.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case DECO0 cannot be acquired - i.e. run_descriptor_deco0() fails
with -ENODEV, caam_probe() enters an endless loop:
run_descriptor_deco0
ret -ENODEV
-> instantiate_rng
-ENODEV, overwritten by -EAGAIN
ret -EAGAIN
-> caam_probe
-EAGAIN results in endless loop
It turns out the error path in instantiate_rng() is incorrect,
the checks are done in the wrong order.
Cc: <stable@vger.kernel.org> # 3.13+
Fixes: 1005bccd7a ("crypto: caam - enable instantiation of all RNG4 state handles")
Reported-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Suggested-by: Auer Lukas <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Offload split key generation in CAAM engine, using DKP.
DKP is supported starting with Era 6.
Note that the way assoclen is transmitted from the job descriptor
to the shared descriptor changes - DPOVRD register is used instead
of MATH3 (where available), since DKP protocol thrashes the MATH
registers.
The replacement of MDHA split key generation with DKP has the side
effect of the crypto engine writing the authentication key, and thus
the DMA mapping direction for the buffer holding the key has to change
from DMA_TO_DEVICE to DMA_BIDIRECTIONAL.
There are two cases:
-key is inlined in descriptor - descriptor buffer mapping changes
-key is referenced - key buffer mapping changes
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Save Era in driver's private data for further usage,
like deciding whether an erratum applies or a feature is available
based on its value.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ablkcipher shared descriptors are relatively small, thus there is enough
space for the key to be inlined.
Accordingly, there is no need to copy the key in ctx->key.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Key data is not modified, it is copied in the shared descriptor.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix below warnings on ARMv7 by using %zu for printing size_t values:
drivers/crypto/caam/caamalg_qi.c: In function aead_edesc_alloc:
drivers/crypto/caam/caamalg_qi.c:417:17: warning: format %lu expects argument of type long unsigned int, but argument 4 has type unsigned int [-Wformat=]
sizeof(struct qm_sg_entry))
^
drivers/crypto/caam/caamalg_qi.c:672:16: note: in expansion of macro CAAM_QI_MAX_AEAD_SG
qm_sg_ents, CAAM_QI_MAX_AEAD_SG);
^
drivers/crypto/caam/caamalg_qi.c: In function ablkcipher_edesc_alloc:
drivers/crypto/caam/caamalg_qi.c:440:17: warning: format %lu expects argument of type long unsigned int, but argument 4 has type unsigned int [-Wformat=]
sizeof(struct qm_sg_entry))
^
drivers/crypto/caam/caamalg_qi.c:909:16: note: in expansion of macro CAAM_QI_MAX_ABLKCIPHER_SG
qm_sg_ents, CAAM_QI_MAX_ABLKCIPHER_SG);
^
drivers/crypto/caam/caamalg_qi.c: In function ablkcipher_giv_edesc_alloc:
drivers/crypto/caam/caamalg_qi.c:440:17: warning: format %lu expects argument of type long unsigned int, but argument 4 has type unsigned int [-Wformat=]
sizeof(struct qm_sg_entry))
^
drivers/crypto/caam/caamalg_qi.c:1062:16: note: in expansion of macro CAAM_QI_MAX_ABLKCIPHER_SG
qm_sg_ents, CAAM_QI_MAX_ABLKCIPHER_SG);
^
Fixes: eb9ba37dc1 ("crypto: caam/qi - handle large number of S/Gs case")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.15:
API:
- Disambiguate EBUSY when queueing crypto request by adding ENOSPC.
This change touches code outside the crypto API.
- Reset settings when empty string is written to rng_current.
Algorithms:
- Add OSCCA SM3 secure hash.
Drivers:
- Remove old mv_cesa driver (replaced by marvell/cesa).
- Enable rfc3686/ecb/cfb/ofb AES in crypto4xx.
- Add ccm/gcm AES in crypto4xx.
- Add support for BCM7278 in iproc-rng200.
- Add hash support on Exynos in s5p-sss.
- Fix fallback-induced error in vmx.
- Fix output IV in atmel-aes.
- Fix empty GCM hash in mediatek.
Others:
- Fix DoS potential in lib/mpi.
- Fix potential out-of-order issues with padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
lib/mpi: call cond_resched() from mpi_powm() loop
crypto: stm32/hash - Fix return issue on update
crypto: dh - Remove pointless checks for NULL 'p' and 'g'
crypto: qat - Clean up error handling in qat_dh_set_secret()
crypto: dh - Don't permit 'key' or 'g' size longer than 'p'
crypto: dh - Don't permit 'p' to be 0
crypto: dh - Fix double free of ctx->p
hwrng: iproc-rng200 - Add support for BCM7278
dt-bindings: rng: Document BCM7278 RNG200 compatible
crypto: chcr - Replace _manual_ swap with swap macro
crypto: marvell - Add a NULL entry at the end of mv_cesa_plat_id_table[]
hwrng: virtio - Virtio RNG devices need to be re-registered after suspend/resume
crypto: atmel - remove empty functions
crypto: ecdh - remove empty exit()
MAINTAINERS: update maintainer for qat
crypto: caam - remove unused param of ctx_map_to_sec4_sg()
crypto: caam - remove unneeded edesc zeroization
crypto: atmel-aes - Reset the controller before each use
crypto: atmel-aes - properly set IV after {en,de}crypt
hwrng: core - Reset user selected rng by writing "" to rng_current
...
ctx_map_to_sec4_sg() function, added in
commit 045e36780f ("crypto: caam - ahash hmac support")
has never used the "desc" parameter, so let's drop it.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Extended descriptor allocation has been changed by
commit dde20ae9d6 ("crypto: caam - Change kmalloc to kzalloc to avoid residual data")
to provide zeroized memory, meaning we no longer have to sanitize
its members - edesc->src_nents and edesc->dst_dma.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam/qi frontend (i.e. caamalg_qi) mustn't be used in case it runs on a
DPAA2 part (this could happen when using a multiplatform kernel).
Fixes: 297b9cebd2 ("crypto: caam/jr - add support for DPAA2 parts")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch replace GCM IV size value by their constant name.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When built using multi_v7_defconfig, driver does not work on LS1021A:
[...]
caam 1700000.crypto: can't identify CAAM ipg clk: -2
caam: probe of 1700000.crypto failed with error -2
[...]
It turns out we have to detect at runtime whether driver is running
on an i.MX platform or not.
Cc: <stable@vger.kernel.org>
Fixes: 6c3af95593 ("crypto: caam - add support for LS1021A")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Most of the dentry members from structure caam_drv_private
are never used at all, so it is safe to remove them.
Since debugfs_remove_recursive() is called, we don't need the
file entries.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for using the caam/jr backend on DPAA2-based SoCs.
These have some particularities we have to account for:
-HW S/G format is different
-Management Complex (MC) firmware initializes / manages (partially)
the CAAM block: MCFGR, QI enablement in QICTL, RNG
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SELF condition has no meaning for the SERIAL sharing since the jobs
are executed in the same DECO.
Signed-off-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clean up the code, as indicated by Coccinelle.
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
sg_to_sec4_sg_len() is no longer used since
commit 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Its functionality has been superseded by the usage of sg_nents_for_len()
returning the number of S/G entries corresponding to the provided length.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change log level for some prints from dev_info() to dev_dbg(), low-level
details are needed only when debugging.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
sg_sw_sec4.h header is not used by caam/qi, thus remove its inclusion.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since ARM64 commit 1dccb598df ("arm64: simplify dma_get_ops"),
dma_ops no longer default to swiotlb_dma_ops, but to dummy_dma_ops.
dma_ops have to be explicitly set in the driver - at least for ARM64.
Fixes: 67c2315def ("crypto: caam - add Queue Interface (QI) backend support")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Associated data (AD) length is read by CAAM from an S/G entry
that is initially filled by the GPP.
Accordingly, AD length has to be stored in CAAM endianness.
Fixes: b189817cf7 ("crypto: caam/qi - add ablkcipher and authenc algorithms")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For more than 16 S/G entries, driver currently corrupts memory
on ARMv8, see below KASAN log.
Note: this does not reproduce on PowerPC due to different (smaller)
cache line size - 64 bytes on PPC vs. 128 bytes on ARMv8.
One such use case is one of the cbc(aes) test vectors - with 8 S/G
entries and src != dst. Driver needs 1 (IV) + 2 x 8 = 17 entries,
which goes over the 16 S/G entries limit:
(CAAM_QI_MEMCACHE_SIZE - offsetof(struct ablkcipher_edesc, sgt)) /
sizeof(struct qm_sg_entry) = 256 / 16 = 16 S/Gs
Fix this by:
-increasing object size in caamqicache pool from 512 to 768; this means
the maximum number of S/G entries grows from (at least) 16 to 32
(again, for ARMv8 case of 128-byte cache line)
-add checks in the driver to fail gracefully (ENOMEM) in case the 32 S/G
entries limit is exceeded
==================================================================
BUG: KASAN: slab-out-of-bounds in ablkcipher_edesc_alloc+0x4ec/0xf60
Write of size 1 at addr ffff800021cb6003 by task cryptomgr_test/1394
CPU: 3 PID: 1394 Comm: cryptomgr_test Not tainted 4.12.0-rc7-next-20170703-00023-g72badbcc1ea7-dirty #26
Hardware name: LS1046A RDB Board (DT)
Call trace:
[<ffff20000808ac6c>] dump_backtrace+0x0/0x290
[<ffff20000808b014>] show_stack+0x14/0x1c
[<ffff200008d62c00>] dump_stack+0xa4/0xc8
[<ffff200008264e40>] print_address_description+0x110/0x26c
[<ffff200008265224>] kasan_report+0x1d0/0x2fc
[<ffff2000082637b8>] __asan_store1+0x4c/0x54
[<ffff200008b4884c>] ablkcipher_edesc_alloc+0x4ec/0xf60
[<ffff200008b49304>] ablkcipher_encrypt+0x44/0xcc
[<ffff20000848a61c>] skcipher_encrypt_ablkcipher+0x120/0x138
[<ffff200008495014>] __test_skcipher+0xaec/0xe30
[<ffff200008497088>] test_skcipher+0x6c/0xd8
[<ffff200008497154>] alg_test_skcipher+0x60/0xe4
[<ffff2000084974c4>] alg_test.part.13+0x130/0x304
[<ffff2000084976d4>] alg_test+0x3c/0x68
[<ffff2000084938ac>] cryptomgr_test+0x54/0x5c
[<ffff20000810276c>] kthread+0x188/0x1c8
[<ffff2000080836c0>] ret_from_fork+0x10/0x50
Allocated by task 1394:
save_stack_trace_tsk+0x0/0x1ac
save_stack_trace+0x18/0x20
kasan_kmalloc.part.5+0x48/0x110
kasan_kmalloc+0x84/0xa0
kasan_slab_alloc+0x14/0x1c
kmem_cache_alloc+0x124/0x1e8
qi_cache_alloc+0x28/0x58
ablkcipher_edesc_alloc+0x244/0xf60
ablkcipher_encrypt+0x44/0xcc
skcipher_encrypt_ablkcipher+0x120/0x138
__test_skcipher+0xaec/0xe30
test_skcipher+0x6c/0xd8
alg_test_skcipher+0x60/0xe4
alg_test.part.13+0x130/0x304
alg_test+0x3c/0x68
cryptomgr_test+0x54/0x5c
kthread+0x188/0x1c8
ret_from_fork+0x10/0x50
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at ffff800021cb5e00
which belongs to the cache caamqicache of size 512
The buggy address is located 3 bytes to the right of
512-byte region [ffff800021cb5e00, ffff800021cb6000)
The buggy address belongs to the page:
page:ffff7e0000872d00 count:1 mapcount:0 mapping: (null)
index:0x0 compound_mapcount: 0
flags: 0xfffc00000008100(slab|head)
raw: 0fffc00000008100 0000000000000000 0000000000000000 0000000180190019
raw: dead000000000100 dead000000000200 ffff800931268200 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff800021cb5f00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff800021cb5f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff800021cb6000: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff800021cb6080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff800021cb6100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Fixes: b189817cf7 ("crypto: caam/qi - add ablkcipher and authenc algorithms")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam/qi needs a fix similar to what was done for caam/jr in
commit "crypto: caam/qi - properly set IV after {en,de}crypt",
to allow for ablkcipher/skcipher chunking/streaming.
Cc: <stable@vger.kernel.org>
Fixes: b189817cf7 ("crypto: caam/qi - add ablkcipher and authenc algorithms")
Suggested-by: David Gstir <david@sigma-star.at>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam/qi driver fails to compile when CONFIG_DEBUG_FORCE_WEAK_PER_CPU=y.
Fix it by making the offending local per_cpu variable global.
Cc: <stable@vger.kernel.org>
Fixes: 67c2315def ("crypto: caam - add Queue Interface (QI) backend support")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam/qi driver does not compile when DEBUG is enabled
(CRYPTO_DEV_FSL_CAAM_DEBUG=y):
drivers/crypto/caam/caamalg_qi.c: In function 'ablkcipher_done':
drivers/crypto/caam/caamalg_qi.c:794:2: error: implicit declaration of function 'dbg_dump_sg' [-Werror=implicit-function-declaration]
dbg_dump_sg(KERN_ERR, "dst @" __stringify(__LINE__)": ",
Since dbg_dump_sg() is shared between caam/jr and caam/qi, move it
in a shared location and export it.
At the same time:
-reduce ifdeferry by providing a no-op implementation for !DEBUG case
-rename it to caam_dump_sg() to be consistent in terms of
exported symbols namespace (caam_*)
Cc: <stable@vger.kernel.org>
Fixes: b189817cf7 ("crypto: caam/qi - add ablkcipher and authenc algorithms")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Certain cipher modes like CTS expect the IV (req->info) of
ablkcipher_request (or equivalently req->iv of skcipher_request) to
contain the last ciphertext block when the {en,de}crypt operation is done.
This is currently not the case for the CAAM driver which in turn breaks
e.g. cts(cbc(aes)) when the CAAM driver is enabled.
This patch fixes the CAAM driver to properly set the IV after the
{en,de}crypt operation of ablkcipher finishes.
This issue was revealed by the changes in the SW CTS mode in commit
0605c41cc5 ("crypto: cts - Convert to skcipher")
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: David Gstir <david@sigma-star.at>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Driver does not properly handle the case when signals interrupt
wait_for_completion_interruptible():
-it does not check for return value
-completion structure is allocated on stack; in case a signal interrupts
the sleep, it will go out of scope, causing the worker thread
(caam_jr_dequeue) to fail when it accesses it
wait_for_completion_interruptible() is replaced with uninterruptable
wait_for_completion().
We choose to block all signals while waiting for I/O (device executing
the split key generation job descriptor) since the alternative - in
order to have a deterministic device state - would be to flush the job
ring (aborting *all* in-progress jobs).
Cc: <stable@vger.kernel.org>
Fixes: 045e36780f ("crypto: caam - ahash hmac support")
Fixes: 4c1ec1f930 ("crypto: caam - refactor key_gen, sg")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is the 2nd part of fixing the usage of GFP_KERNEL for memory
allocations, taking care off all the places that haven't caused a real
problem / failure.
Again, the issue being fixed is that GFP_KERNEL should be used only when
MAY_SLEEP flag is set, i.e. MAY_BACKLOG flag usage is orthogonal.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Changes in the SW cts (ciphertext stealing) code in
commit 0605c41cc5 ("crypto: cts - Convert to skcipher")
revealed a problem in the CAAM driver:
when cts(cbc(aes)) is executed and cts runs in SW,
cbc(aes) is offloaded in CAAM; cts encrypts the last block
in atomic context and CAAM incorrectly decides to use GFP_KERNEL
for memory allocation.
Fix this by allowing GFP_KERNEL (sleeping) only when MAY_SLEEP flag is
set, i.e. remove MAY_BACKLOG flag.
We split the fix in two parts - first is sent to -stable, while the
second is not (since there is no known failure case).
Link: http://lkml.kernel.org/g/20170602122446.2427-1-david@sigma-star.at
Cc: <stable@vger.kernel.org> # 4.8+
Reported-by: David Gstir <david@sigma-star.at>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2376 808 128 3312 cf0 drivers/crypto/caam/jr.o
File size after constify caam_jr_match:
text data bss dec hex filename
2976 192 128 3296 ce0 drivers/crypto/caam/jr.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto_akcipher_maxsize() asks for the output buffer size without
caring for errors. It allways assume that will be called after
a valid setkey. Comply with it and return what he wants.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM RSA private key may have either of three representations.
1. The first representation consists of the pair (n, d), where the
components have the following meanings:
n the RSA modulus
d the RSA private exponent
2. The second representation consists of the triplet (p, q, d), where
the
components have the following meanings:
p the first prime factor of the RSA modulus n
q the second prime factor of the RSA modulus n
d the RSA private exponent
3. The third representation consists of the quintuple (p, q, dP, dQ,
qInv),
where the components have the following meanings:
p the first prime factor of the RSA modulus n
q the second prime factor of the RSA modulus n
dP the first factors's CRT exponent
dQ the second factors's CRT exponent
qInv the (first) CRT coefficient
The benefit of using the third or the second key form is lower
computational cost for the decryption and signature operations.
This patch adds support for the third RSA private key
representations and extends caampkc to use the fastest key when all
related components are present in the private key.
Signed-off-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Radu Alexe <radu.alexe@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM RSA private key may have either of three representations.
1. The first representation consists of the pair (n, d), where the
components have the following meanings:
n the RSA modulus
d the RSA private exponent
2. The second representation consists of the triplet (p, q, d), where
the
components have the following meanings:
p the first prime factor of the RSA modulus n
q the second prime factor of the RSA modulus n
d the RSA private exponent
3. The third representation consists of the quintuple (p, q, dP, dQ,
qInv),
where the components have the following meanings:
p the first prime factor of the RSA modulus n
q the second prime factor of the RSA modulus n
dP the first factors's CRT exponent
dQ the second factors's CRT exponent
qInv the (first) CRT coefficient
The benefit of using the third or the second key form is lower
computational cost for the decryption and signature operations.
This patch adds support for the second RSA private key
representation.
Signed-off-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Radu Alexe <radu.alexe@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This function will be used into further patches.
Signed-off-by: Radu Alexe <radu.alexe@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function returns NULL if buf is composed only of zeros.
Signed-off-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix to return error code -ENOMEM from the kmem_cache_create() error
handling case instead of 0(err is 0 here), as done elsewhere in this
function.
Fixes: 67c2315def ("crypto: caam - add Queue Interface (QI) backend support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
RNG instantiation was previously fixed by
commit 62743a4145 ("crypto: caam - fix RNG init descriptor ret. code checking")
while deinstantiation was not addressed.
Since the descriptors used are similar, in the sense that they both end
with a JUMP HALT command, checking for errors should be similar too,
i.e. status code 7000_0000h should be considered successful.
Cc: <stable@vger.kernel.org> # 3.13+
Fixes: 1005bccd7a ("crypto: caam - enable instantiation of all RNG4 state handles")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case caam_jr_alloc() fails, ctx->dev carries the error code,
thus accessing it with dev_err() is incorrect.
Cc: <stable@vger.kernel.org> # 4.8+
Fixes: 8c419778ab ("crypto: caam - add support for RSA algorithm")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The way Job Ring platform devices are created and released does not
allow for multiple create-release cycles.
JR0 Platform device creation error
JR0 Platform device creation error
caam 2100000.caam: no queues configured, terminating
caam: probe of 2100000.caam failed with error -12
The reason is that platform devices are created for each job ring:
for_each_available_child_of_node(nprop, np)
if (of_device_is_compatible(np, "fsl,sec-v4.0-job-ring") ||
of_device_is_compatible(np, "fsl,sec4.0-job-ring")) {
ctrlpriv->jrpdev[ring] =
of_platform_device_create(np, NULL, dev);
which sets OF_POPULATED on the device node, but then it cleans these up:
/* Remove platform devices for JobRs */
for (ring = 0; ring < ctrlpriv->total_jobrs; ring++) {
if (ctrlpriv->jrpdev[ring])
of_device_unregister(ctrlpriv->jrpdev[ring]);
}
which leaves OF_POPULATED set.
Use of_platform_populate / of_platform_depopulate instead.
This allows for a bit of driver clean-up, jrpdev is no longer needed.
Logic changes a bit too:
-exit in case of_platform_populate fails, since currently even QI backend
depends on JR; true, we no longer support the case when "some" of the JR
DT nodes are incorrect
-when cleaning up, caam_remove() would also depopulate RTIC in case
it would have been populated somewhere else - not the case for now
Cc: <stable@vger.kernel.org>
Fixes: 313ea293e9 ("crypto: caam - Add Platform driver for Job Ring")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Suggested-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
