If the driver doesn't support 40 MHz channels, then
mac80211 erroneously sets number of RX chains to one
although the number of chains is independent of the
support for 40 MHz channels.
Fix this by checking the 40 MHz support only for the
code that sets the 40 MHz channel not the complete
HT code block.
This also means the HT20 channel type will always be
set in the changed code block so there's no need to
set it in case we override the AP due to invalid IEs
in the probe response/beacon.
The indentation is a bit quirky, but I'm rewriting
this code for VHT support so this will change again
very soon.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radiotap vendor area in the skb head must be skipped
and accounted for in a few functions until it is removed.
I missed this in my patch, so a few places use this data
as though it was the 802.11 header, fix these places.
Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
From Kukjin Kim:
Here is Samsung fixes for v3.7 and it is for fixing of mdma1 address
for exynos4210 rev0 SoC.
* 'v3.7-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
Signed-off-by: Olof Johansson <olof@lixom.net>
The new EEH code introduced a small regression, if the EEH PEs
are missin (which happens currently in qemu for example), it
will deref a NULL pointer in the MSI code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Starting from 3.6 we cache output routes for
multicasts only when using route to 224/4. For local receivers
we can set RTCF_LOCAL flag depending on the membership but
in such case we use maddr and saddr which are not caching
keys as before. Additionally, we can not use same place to
cache routes that differ in RTCF_LOCAL flag value.
Fix it by caching only RTCF_MULTICAST entries
without RTCF_LOCAL (send-only, no loopback). As a side effect,
we avoid unneeded lookup for fnhe when not caching because
multicasts are not redirected and they do not learn PMTU.
Thanks to Maxime Bizon for showing the caching
problems in __mkroute_output for 3.6 kernels: different
RTCF_LOCAL flag in cache can lead to wrong ip_mc_output or
ip_output call and the visible problem is that traffic can
not reach local receivers via loopback.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is work the same as for ipv4.
All other hacks about tcp repair are in common code for ipv4 and ipv6,
so this patch is enough for repairing ipv6 connections.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains two Netfilter fixes:
* Fix buffer overflow in the name of the timeout policy object
in the cttimeout infrastructure, from Florian Westphal.
* Fix a bug in the hash set in case that IP ranges are
specified, from Jozsef Kadlecsik.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
This pull request is intended for net-next and contains the following changes:
1) Remove a redundant check when initializing the xfrm replay functions,
from Ulrich Weber.
2) Use a faster per-cpu helper when allocating ipcomt transforms,
from Shan Wei.
3) Use a static gc threshold value for ipv6, simmilar to what we do
for ipv4 now.
4) Remove a commented out function call.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
This pull request is intended for 3.7 and contains a single patch to
fix the IPsec gc threshold value for ipv4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeffrey Barish reported an obvious bug in the pcm part of the usb-audio
driver which causes the code to not initialize the sync endpoint from
configure_endpoint().
Reported-by: Jeffrey Barish <jeff_barish@earthlink.net>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There used to be a time when TIPC had lots of Kconfig knobs the
end user could alter, but they have all been made automatic or
obsolete, with the exception of CONFIG_TIPC_PORTS. This
previously existing set of options was all hidden under the
TIPC_ADVANCED setting, which does not exist in any code, but
only in Kconfig scope.
Having this now, just to hide the one remaining "advanced"
option no longer makes sense. Remove it. Also get rid of the
ifdeffery in the TIPC code that allowed for TIPC_PORTS to be
possibly undefined.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
As the variable:node is currently defined to u32 type, it is
unnecessary to cast its type to u32 again when using it.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Upon establishing a first link between two nodes, there is
currently a risk that the two endpoints will disagree on exactly
which sequence number reception and acknowleding of broadcast
packets should start.
The following scenarios may happen:
1: Node A sends an ACTIVATE message to B, telling it to start acking
packets from sequence number N.
2: Node A sends out broadcast N, but does not expect an acknowledge
from B, since B is not yet in its broadcast receiver's list.
3: Node A receives ACK for N from all nodes except B, and releases
packet N.
4: Node B receives the ACTIVATE, activates its link endpoint, and
stores the value N as sequence number of first expected packet.
5: Node B sends a NAME_DISTR message to A.
6: Node A receives the NAME_DISTR message, and activates its endpoint.
At this moment B is added to A's broadcast receiver's set.
Node A also sets sequence number 0 as the first broadcast packet
to be received from B.
7: Node A sends broadcast N+1.
8: B receives N+1, determines there is a gap in the sequence, since
it is expecting N, and sends a NACK for N back to A.
9: Node A has already released N, so no retransmission is possible.
The broadcast link in direction A->B is stale.
In addition to, or instead of, 7-9 above, the following may happen:
10: Node B sends broadcast M > 0 to A.
11: Node A receives M, falsely decides there must be a gap, since
it is expecting packet 0, and asks for retransmission of packets
[0,M-1].
12: Node B has already released these packets, so the broadcast
link is stale in direction B->A.
We solve this problem by introducing a new unicast message type,
BCAST_PROTOCOL/STATE, to convey the sequence number of the next
sent broadcast packet to the other endpoint, at exactly the moment
that endpoint is added to the own node's broadcast receivers list,
and before any other unicast messages are permitted to be sent.
Furthermore, we don't allow any node to start receiving and
processing broadcast packets until this new synchronization
message has been received.
To maintain backwards compatibility, we still open up for
broadcast reception if we receive a NAME_DISTR message without
any preceding broadcast sync message. In this case, we must
assume that the other end has an older code version, and will
never send out the new synchronization message. Hence, for mixed
old and new nodes, the issue arising in 7-12 of the above may
happen with the same probability as before.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A few more fixes for final 3.7. Two dealing with pinmux setup on OMAP, and
one dealing with TV output on DaVinci. And one small MAINTAINER update.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQrWG6AAoJEIwa5zzehBx3NyoP/0GKwGZAPnCCWuzdMc/8geQu
QfPuZqmaRiJXp58CfuOi/2kyw1EPkSVwg7I2i3q+ki9U/H7UlvBPBVIiqnvGwg6o
oNRHHGyfp2EtLCU01+faLZTPHXh7BPRzuq5Mp7puPDnNMhgBWjHi3Qmpcf7HX8Gb
SkY3WBlMiH0xmWA2vNTRMslHbs3/CXYRzQ82KdttV4qoAbWyt7OAv7UbhKCKuAE7
R1gtH7oVnKPrRjp6G1PvxWfCzSDz+XYWZnSGTGtBPEVUWg9p1J/SV0MhQxvlVG9a
8ABLPGUQXn1ElsblSjyvFJSpVDTa+PxbfYXUGfC8xppmP+Q/fI/Ycp0dwnSvXYsN
Pvm6ONQAbkWCrNXMFjz2de9C0/4VcPIArirV7vPW0PwBdPfaKMDSw28obrAoamG1
taJy1fJvUetVaGN2u7LcQfvwecHevHyJBo2fgqukqKrapAmqKINU7MBjYATW371K
Ean7vVH/HzSfEkFl8mT/azTZYeWp4zhMyXKQ+KbhEWYLUSGmeUEqlJIvu6QzQ/Y3
JBx8bJ9mwaCx9JMjyaEqbixKr6ceiseOcO3moduAg2UIWNAa3fwRN1VkZB4vzxQ2
VZswVg2/tTVVZ03cqnR78vi6mKDBwBbvwRL1WyGP4oWubFtBj8DpkO1rqfW5Pqgo
4c1u/OuUOascJ2baJy2v
=FhMC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few more fixes for final 3.7. Two dealing with pinmux setup on
OMAP, and one dealing with TV output on DaVinci. And one small
MAINTAINER update."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: davinci: dm644x: fix out range signal for ED
ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
ARM: OMAP: Add maintainer entry for IGEP machines
This is two bug fixes: one fixes a loophole where rt_sigprocmask() with the
wrong values panics the box (Denial of Service) and the other fixes an
aliasing problem with get_shared_area() which could cause data corruption.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQrfisAAoJEDeqqVYsXL0MabcIALeL/hMtLSdwo01AG47Z6v6u
jNuQIE6v3mvsaoJ5zxhM570/SZc+waDojfNpax+RjJc4vppDHq40xhI19RHczCvo
AIASYIZynMHF1kqXsFpWfDtOGUzRtFjn8g60rfX593ghtpuliTXm+WgYCl43SyYm
Ee1rLAFrEiXKAHyTO+QXi/EiTHPDGxw84fZdypIC7Bxi0JZg7SX5g/KXwGC2JT7M
fRW2SmrfgFOLMvmYYbyk4BWvZ4dneikcUhOJGiLcpSy++MJF6ccjbfiCD4i6gD9e
cM57jLnHnV2U+qp4e2Rcosi9AQwfSYRkr7j37/OT0KoCLmSRZbwqpF1RMjMKyGM=
=ckHH
-----END PGP SIGNATURE-----
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PARISC fixes from James Bottomley:
"This is two bug fixes: one fixes a loophole where rt_sigprocmask()
with the wrong values panics the box (Denial of Service) and the other
fixes an aliasing problem with get_shared_area() which could cause
data corruption.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix user-triggerable panic on parisc
[PARISC] fix virtual aliasing issue in get_shared_area()
This is a set of four bug fixes. The isci one is an obvious thinko (using
request buffer instead of response buffer) which causes a command to fail.
The three others are DIF/DIX updates which are required because they're part
of a series of ten patches, the other seven of which went into the block layer
during the merge window meaning our current DIF/DIX implementation is broken
without these three.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQre/4AAoJEDeqqVYsXL0MrxwH/A+b3aYvany+ZPg+elAFBCFm
3qHJ2Bys+M/kTkb0Fqb/l1KQfGFjooqcozm6eTgIeZ67bK947pxzu4Txy4JmeXvC
cHQ2lzEzcIFjiyVqV0tQ/wxMCnHTeqDx1WX02aw3T6e5JxObe+gC1pAEoMz2unSk
kpsSvFKBfCBMY6bmbVY5c2vpFTgD4UKtBiKn/GKtLtIDvynRx0P5e7/TNawxUB64
QZ/tu3Z2Ov5g9VWod+LpQwjVI+bIBlBEV4Of+91zou64aocrqXtSoky+ae9mwfPy
7KLLZzz5Fzc5KwT8ynEECtU2iFQXJ/zXNDRh7gBffc0ReljpuouOvIgqdZEW8d0=
=kQyb
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of four bug fixes.
The isci one is an obvious thinko (using request buffer instead of
response buffer) which causes a command to fail.
The three others are DIF/DIX updates which are required because
they're part of a series of ten patches, the other seven of which went
into the block layer during the merge window meaning our current
DIF/DIX implementation is broken without these three.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] sd: Implement support for WRITE SAME
[SCSI] sd: Permit merged discard requests
[SCSI] Add a report opcode helper
[SCSI] isci: copy fis 0x34 response into proper buffer
Pull drm fixes from Dave Airlie.
Small fixes for (mostly Nouveau, some radeon) regressions.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: use the correct fence implementation for nv50
drm/radeon: add new SI pci id
radeon: add AGPMode 1 quirk for RV250
drm/radeon: properly track the crtc not_enabled case evergreen_mc_stop()
drm/nouveau/bios: fix DCB v1.5 parsing
drm/nouveau: add missing pll_calc calls
drm/nouveau: fix crash with noaccel=1
drm/nv40: allocate ctxprog with kmalloc
drm/nvc0/disp: fix thinko in vblank regression fix..
Do not fail if dpll4_m4_ck is missing. The clock is not there on omap24xx,
so this should not be a hard error.
The patch retains the functionality before the commit 185bae10 (OMAPDSS:
DSS: Cleanup cpu_is_xxxx checks).
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
added usb-id as driver supports the stick
Signed-off-by: Andrew Karpow <andy@mailbox.tu-berlin.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID as driver supports it.
Reported-by: Hubert Lin <hubertwslin@gmail.com>
Tested-by: Hubert Lin <hubertwslin@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the MT9V022_TOTAL_SHUTTER_WIDTH register is controlled in manual
mode by V4L2_CID_EXPOSURE control, it shouldn't be written directly in
mt9v022_s_crop(). In manual mode this register should be set to the
V4L2_CID_EXPOSURE control value. Changing this register directly and
outside of the actual control function means that the register value
is not in sync with the corresponding control value. Thus, the following
problem is observed:
- setting this control initially succeeds
- VIDIOC_S_CROP ioctl() overwrites the MT9V022_TOTAL_SHUTTER_WIDTH
register
- setting this control to the same value again doesn't
result in setting the register since the control value
was previously cached and doesn't differ
Remove MT9V022_TOTAL_SHUTTER_WIDTH register setting in mt9v022_s_crop()
and add a comment explaining why it is not needed in manual mode.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the missing unlock on the error handle path in function
mx2_start_streaming().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the "supported" flag in bclink structure to "recv_permitted"
to better reflect what it is used for. When this flag is set for a
given node, we are permitted to receive and acknowledge broadcast
messages from that node. Convert it to a bool at the same time,
since it is not used to store any numerical values.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The "supportable" flag in bclink structure is a compatibility flag
indicating whether a peer node is capable of receiving TIPC broadcast
messages. However, all TIPC versions since tipc-1.5, and after the
inclusion in the upstream Linux kernel in 2006, support this capability.
It is highly unlikely that anybody is still using such an old
version of TIPC, let alone that they want to mix it with TIPC-2.0
nodes. Therefore, we now remove the "supportable" flag.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in omap1_camera. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
.set_crop() implementation in mx1_camera is identical with the default.
Remove the copy to switch to using the default stab.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx2_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx3_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in pxa_camera.c. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_mobile_ceu_camera. Fix them by cleanly separating writable
and read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_vou. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change makes it so that only the first fragment in a series of fragments
will have the L4 header pulled. Previously we were always pulling the L4
header as well and in the case of UDP this can harm performance since only the
first fragment will have the header, the rest just contain data which should
be left in the paged portion of the packet.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Historically, we've been using the APME bit to determine whether a device
supports wake on a given port or not. However, this bit specifies the
default wake setting, rather than the wake support. Change the behavior so
that we use a flag to keep the capabilities separate from the enablement
while meeting customer requirements.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the filters to be more consistent with what the driver wants to do.
For example, for devices that timestamp all packets, report that the filter
is set for timestamping all packets.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a bitwise operation error in the fdb_add block
that was only allowing FDB types that were not permanent.
This was the opposite of the intent because the hardware
never ages out address these are the _only_ type of addrs
that should be allowed.
This was missed because until recently iproute2 did not
set any bit for this by default. And our test code to
manage FDB entries on embedded devices similarly did not
set these bits.
I am going to chalk this up as a bug and fix it now.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables ethtool to correctly identify flow control (pause
frame) auto negotiation, as well as disallow enabling it when it is not
supported. The ixgbe_device_supports_autoneg_fc function is exported and
used for this purpose.
There is also one minor cleanup of the device_supports_autoneg_fc by
removing an unnecessary return statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the queuing that was previously done for L4 packets
as it is not needed. The filter does not provide functionality, and it
is possible that queue setup here could trample settings done else-where
in the driver. (for example it may use a queue which isn't setup.)
Setting of the queue is not required for hardware timestamping and could
have inadverdent side effects.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes a magic number that was used for the ETQF used for
filtering L2 ptp packets and replaces it with the supplied define that
previously existed. The intent is to clarify that this filter is already
set aside for L2 1588 work.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reformats the output of the Tx/Rx descriptor dumps to more
appropriately align the output of the ixgbe_dump and improve readability.
Prevents empty Tx descriptors from being displayed to decrease the size
of the dump and make it more manageable.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
int sys32_rt_sigprocmask(int how, compat_sigset_t __user *set, compat_sigset_t __user *oset,
unsigned int sigsetsize)
{
sigset_t old_set, new_set;
int ret;
if (set && get_sigset32(set, &new_set, sigsetsize))
...
static int
get_sigset32(compat_sigset_t __user *up, sigset_t *set, size_t sz)
{
compat_sigset_t s;
int r;
if (sz != sizeof *set) panic("put_sigset32()");
In other words, rt_sigprocmask(69, (void *)69, 69) done by 32bit process
will promptly panic the box.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When a write to a replacement device completes, we carefully
and correctly found the rdev that the write actually went to
and the blithely called rdev_dec_pending on the primary rdev,
even if this write was to the replacement.
This means that any writes to an array while a replacement
was ongoing would cause the nr_pending count for the primary
device to go negative, so it could never be removed.
This bug has been present since replacement was introduced in
3.3, so it is suitable for any -stable kernel since then.
Reported-by: "George Spelvin" <linux@horizon.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When a replacement operation completes there is a small window
when the original device is marked 'faulty' and the replacement
still looks like a replacement. The faulty should be removed and
the replacement moved in place very quickly, bit it isn't instant.
So the code write out to the array must handle the possibility that
the only working device for some slot in the replacement - but it
doesn't. If the primary device is faulty it just gives up. This
can lead to corruption.
So make the code more robust: if either the primary or the
replacement is present and working, write to them. Only when
neither are present do we give up.
This bug has been present since replacement was introduced in
3.3, so it is suitable for any -stable kernel since then.
Reported-by: "George Spelvin" <linux@horizon.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Alex writes:
A couple more small fixes for 3.7:
- another evergreen_mc fix
- add an AGP quirk for an old RV250
- new pci id.
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add new SI pci id
radeon: add AGPMode 1 quirk for RV250
drm/radeon: properly track the crtc not_enabled case evergreen_mc_stop()
nouveau: one more regression fix.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: use the correct fence implementation for nv50
Some more misc fallout from nouveau rework.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix DCB v1.5 parsing
drm/nouveau: add missing pll_calc calls
drm/nouveau: fix crash with noaccel=1
drm/nv40: allocate ctxprog with kmalloc
drm/nvc0/disp: fix thinko in vblank regression fix..
Only compile time tested, noticed nv50_fence_create was never used,
so fix this. This will probably fix vblank on nv50 cards.
Hopefully this is still in time for 3.7 final release.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently at the TIPC bearer layer there is the following congestion
mechanism:
Once sending packets has failed via that bearer, the bearer will be
flagged as being in congested state at once. During bearer congestion,
all packets arriving at link will be queued on the link's outgoing
buffer. When we detect that the state of bearer congestion has
relaxed (e.g. some packets are received from the bearer) we will try
our best to push all packets in the link's outgoing buffer until the
buffer is empty, or until the bearer is congested again.
However, in fact the TIPC bearer never receives any feedback from the
device layer whether a send was successful or not, so it must always
assume it was successful. Therefore, the bearer congestion mechanism
as it exists currently is of no value.
But the bearer blocking state is still useful for us. For example,
when the physical media goes down/up, we need to change the state of
the links bound to the bearer. So the code maintaing the state
information is not removed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When a socket is shut down, we should wake up all thread sleeping on
it, instead of just one of them. Otherwise, when several threads are
polling the same socket, and one of them does shutdown(), the
remaining threads may end up sleeping forever.
Also, to align socket usage with common practice in other stacks, we
use one of the common socket callback handlers, sk_state_change(),
to wake up pending users. This is similar to the usage in e.g.
inet_shutdown(). [net/ipv4/af_inet.c].
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
