commit 2d87dc0e5b ("arm64: dts: renesas: r8a7795: Add address
properties to rcar_sound port nodes") added missing #address-cells
and #size-cells for sound ports.
But, these are based on platform, not on SoC. This patch cleanups it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the r8a7795 and r8a7796 device trees over to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The definition of CPG_AUDIO_CLK_I is SoC-specific, not board-specific.
Hence move it from the board-specific .dts files to the SoC-specific
.dtsi files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Split off support for Salvator-X boards with the ES1.x revision of the
R-Car H3 SoC into a separate file. The main r8a7795-salvator-x.dts file
now corresponds to Salvator-X with R-Car H3 ES2.0 or later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update r8a7795.dtsi so it corresponds to R-Car H3 ES2.0 or later:
- The following devices no longer exist on ES2.0, and are thus removed:
fcpf2, fcpvd3, fcpvi2, fdp1-2, usb3-if1, vspd3, vspi2.
- The DU <-> VSPD topology is different on ES2.0, hence remove the
"compatible" and "vsps" properties from the DU node until the driver
can handle this.
Move support for the ES1.x revision of the R-Car H3 SoC into a
separate file. To avoid duplication, r8a7795-es1.dtsi includes
r8a7795.dtsi, and adds device nodes and properties where needed.
Note that while currently r8a7795-es1.dtsi only adds device nodes,
removal of devices nodes and properties can be implemented using the
/delete-node/ and /delete-property/ keywords, as shown below:
&soc {
/delete-node/ <name>@<addr>;
};
&<label> {
/delete-property/ <prop>;
};
Switch r8a7795-salvator-x.dts and r8a7795-h3ulcb.dts from r8a7795.dtsi
to r8a7795-es1.dtsi to preserve compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the HDMI encoders for the H3 Salvator-X board. The number of
encoders varies between the H3 and M3-W SoCs, so they can't be enabled
in the common salvator-x.dtsi file.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU1 and DU2 external dot clocks are provided by the fixed frequency
clock generators X21 and X22, while the DU0 and DU3 clocks are provided
by the programmable Versaclock5 clock generator.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas Salvator-X development board can be equipped with either an
R-Car H3 or M3-W SiP, which are pin-compatible. Both boards use
different DTBs.
Reduce duplication by extracting common Salvator-X board support into
its own .dtsi file. References to SoC-specific clocks are handled
through cpp definitions. Sort device nodes while at it.
For boards with an R-Car H3 SiP, there are no functional changes.
For boards with an R-Car M3-W SiP, the following new devices are now
described in DT:
- External audio, CAN, and PCIe clocks,
- USB Vbus regulator,
- CS2000 clock generator,
- AK4613 Audio Codec,
- VGA.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The current practice is to not add _clk suffixes to clock node names in
DT, as these names are used as the actual clock names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7795.dtsi, so there is no need to update their statuses again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values. Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set PHY rxc-skew-ps to 1500 and all other values to their default values.
This is intended to to address failures in the case of 1Gbps communication
using the by salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables I2C for DVFS device for for Salvator-X board on
R8A7795 SoC.
Signed-off-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CTU (= Channel Transfer Unit) support which is needed
to sound mixing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since this board doesn't mount pull-up/down registers for
USB1_{OVC,PWEN} pins, we should enable bias setting to pull these
pins up/down.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declaring the endpoint makes LVDS enablement easier by just including
the corresponding panel's dtsi file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only the VGA output is supported for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We have to set SW15 to pin 2-3 side on the board before we use CN9
as USB host or peripheral.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch also adds a regulator node for USB2.0 to handle VBUS on/off
by the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /regulator@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On the Salvator-X development board, the RTS and CTS pins of debug
serial-1 port SCIF1 are wired to the CP2102 Serial-USB bridge. Reflect
this in the DTS by adding the "uart-has-rtscts" property to the scif1
device node.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Reported-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It can be used for the watchdog.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
This patch updates the kzm9g device tree to use the generic properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
We should set SW15 to pin 2-3 side on the board before we use CN9
as USB host or peripheral.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This board has a MAX3355 chip. However, we cannot use the extcon/max3355
driver because the ID pin doesn't connect to a gpio pin (in other words,
it connects to the SoC specific pin).
And, the phy-rcar-gen3-usb2 driver cannot handle such a chip for now.
So, this patch enables usb2_phy of channel 1 and 2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the exposed SD card slots. The on-board eMMC needs to wait until we
fixed the 8bit support.
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates:
- SCIF:
- Supports now 50, 230400, 460800, 500000, and 921600 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
- HSCIF:
- Supports now 50, 75, and 110 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables SATA device in r8a7795-salvator-x.dts.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
CS2000 needs AUDIO_CLKOUT as master clock which is generated
by Renesas sound, and Renesas sound needs CS2000 as ADUIO_CLK_B.
Because of this relationship, it will be dead-lock when driver probe.
cs2000: clk_multiplier@4f {
...
clocks = <&rcar_sound 0>, <&x12_clk>;
...
};
&rcar_sound {
...
assigned-clocks = <&cs2000>;
...
};
This patch is using dummy audio_clkout to avoid this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PIO sound support for Salvator-X board.
It can use 44.1kHz base sound only at this point, since 48kHz base
sound needs CS2000, but it is not yet upstreamed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
