This patch adds and enables the device-tree definitions for
both qcom,ipq4019-wifi blocks for the IPQ4019.
Support for these have been added into the ath10k driver since:
commit 280e762e9c ("ath10k: enable ipq4019 device probe in ahb module")
The binding documentation was added in:
commit a47aaa69de ("dt: bindings: add new dt entry for pre calibration in qcom, ath10k.txt")
This has been tested on an ASUS RT-AC58U (IPQ4019),
an AVM Fritz!Box 4040 (IPQ4018), a Compex WPJ428 (IPQ4028)
and a Cisco Meraki MR33 (IPQ4029).
| a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff [...]
| a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
| a000000.wifi: firmware ver 10.4-3.4-00082 api 5 features no-p2p,mfp,[...]
| a000000.wifi: board_file api 2 bmi_id 0:16 crc32 5773b188
| a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file [...]
...
| a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
| a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
| a800000.wifi: firmware ver 10.4-3.4-00082 api 5 features no-p2p, [...]
| a800000.wifi: board_file api 2 bmi_id 0:17 crc32 5773b188
| a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file [...]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This architecture has a pseudo random number generator
supported by the existing "qcom,prng" binding.
rngtest: bits received from input: 5795960032
rngtest: FIPS 140-2 successes: 289591
rngtest: FIPS 140-2 failures: 207
rngtest: FIPS 140-2(2001-10-10) Monobit: 25
rngtest: FIPS 140-2(2001-10-10) Poker: 28
rngtest: FIPS 140-2(2001-10-10) Runs: 91
rngtest: FIPS 140-2(2001-10-10) Long run: 67
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=244; avg=46122; max=3906250)Kibits/s
rngtest: FIPS tests speed: (min=1.327; avg=20.966; max=26.345)Mibits/s
rngtest: Program run time: 386965827 microseconds
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The node for xo and timer belong to the SoC DTS file.
Else, new board DT files may not inherit these nodes.
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes the pinctrl node addresses to be the correct format.
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the blsp_dma node to the device tree and the required
properties for using DMA with serial
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the crypto nodes to the ipq4019 device tree, it also adds the
BAM node used by crypto as well which the driver currently requires to
operate properly
The crypto driver itself depends on some other patches to qcom_bam_dma
to function properly:
https://lkml.org/lkml/2015/12/1/113
CC: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This will allow boards to enable the SPI bus
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This will allow boards to enable watchdog support
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial board support dts files for DK01 board.
Signed-off-by: Senthilkumar N L <snlakshm@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
