The function description for igc_alloc_rx_buffers has not reflected
the function meaning. Add meaningful description.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function description for igc_is_non_eop includes an extra @skb
parameter description. This parameter doesn't exist on the function, so
remove it.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the pci_release_mem_regions method instead of the
pci_release_selected_regions method
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Improve the probe flow and set both the DMA mask and the coherent
to the same thing. Make the flow optimized and cleared.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Scatter gather is used to do DMA data transfers of data that is written to
noncontiguous areas of memory.
This patch enables scatter gather support.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If Rx flow control has been enabled (via autoneg or forced), packets
should not be dropped due to Rx descriptor ring exhaustion. Instead
pause frames should be used to apply back pressure. This only applies
if VFs are not in use.
Move SRRCTL setup to its own function for easy reuse and only set drop
enable bit if Rx flow control is not enabled.
Since v1: always enable dropping of packets if VFs in use.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When disabling PTP timestamping, don't reset the switch with the new
static config until all existing PTP frames have been timestamped on the
RX path or dropped. There's nothing we can do with these afterwards.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And move the queue of skb's waiting for RX timestamps into the ptp_data
structure, since it isn't needed if PTP is not compiled.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'eth_zero_addr()' is already called in the error handling path. This is
harmless, but there is no point in calling it twice, so remove one.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.
But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.
Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.
There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.
So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
Fixes: f0ee7acfcd ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wan/fsl_ucc_hdlc.c: In function ucc_hdlc_irq_handler:
drivers/net/wan/fsl_ucc_hdlc.c:643:23:
warning: variable ut_info set but not used [-Wunused-but-set-variable]
drivers/net/wan/fsl_ucc_hdlc.c: In function uhdlc_suspend:
drivers/net/wan/fsl_ucc_hdlc.c:880:23:
warning: variable ut_info set but not used [-Wunused-but-set-variable]
drivers/net/wan/fsl_ucc_hdlc.c: In function uhdlc_resume:
drivers/net/wan/fsl_ucc_hdlc.c:925:6:
warning: variable ret set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If packet checker is enabled in the serdes, then Rx counter registers
start working, and no side effects have been detected.
This patch enables packet checker automatically when powering serdes on,
and exposes Rx counter registers via ethtool statistics interface.
Code partially basded by older attempt by Andrew Lunn.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/amazon/ena/ena_netdev.c: In function ena_xdp_xmit_buff:
drivers/net/ethernet/amazon/ena/ena_netdev.c:316:19: warning:
variable rx_ring set but not used [-Wunused-but-set-variable]
commit 548c4940b9 ("net: ena: Implement XDP_TX action")
left behind this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set variable 'mbus' static
since new value always be assigned before use it.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing NULL to ppp_pernet causes a crash via BUG_ON.
Dereferencing net in net_generic() also has the same effect.
This patch removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-12-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 127 non-merge commits during the last 17 day(s) which contain
a total of 110 files changed, 6901 insertions(+), 2721 deletions(-).
There are three merge conflicts. Conflicts and resolution looks as follows:
1) Merge conflict in net/bpf/test_run.c:
There was a tree-wide cleanup c593642c8b ("treewide: Use sizeof_field() macro")
which gets in the way with b590cb5f80 ("bpf: Switch to offsetofend in
BPF_PROG_TEST_RUN"):
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, priority) +
sizeof_field(struct __sk_buff, priority),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, priority),
>>>>>>> 7c8dce4b16
There are a few occasions that look similar to this. Always take the chunk with
offsetofend(). Note that there is one where the fields differ in here:
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, tstamp) +
sizeof_field(struct __sk_buff, tstamp),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, gso_segs),
>>>>>>> 7c8dce4b16
Just take the one with offsetofend() /and/ gso_segs. Latter is correct due to
850a88cc40 ("bpf: Expose __sk_buff wire_len/gso_segs to BPF_PROG_TEST_RUN").
2) Merge conflict in arch/riscv/net/bpf_jit_comp.c:
(I'm keeping Bjorn in Cc here for a double-check in case I got it wrong.)
<<<<<<< HEAD
if (is_13b_check(off, insn))
return -1;
emit(rv_blt(tcc, RV_REG_ZERO, off >> 1), ctx);
=======
emit_branch(BPF_JSLT, RV_REG_T1, RV_REG_ZERO, off, ctx);
>>>>>>> 7c8dce4b16
Result should look like:
emit_branch(BPF_JSLT, tcc, RV_REG_ZERO, off, ctx);
3) Merge conflict in arch/riscv/include/asm/pgtable.h:
<<<<<<< HEAD
=======
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
#define vmemmap ((struct page *)VMEMMAP_START)
>>>>>>> 7c8dce4b16
Only take the BPF_* defines from there and move them higher up in the
same file. Remove the rest from the chunk. The VMALLOC_* etc defines
got moved via 01f52e16b8 ("riscv: define vmemmap before pfn_to_page
calls"). Result:
[...]
#define __S101 PAGE_READ_EXEC
#define __S110 PAGE_SHARED_EXEC
#define __S111 PAGE_SHARED_EXEC
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
[...]
Let me know if there are any other issues.
Anyway, the main changes are:
1) Extend bpftool to produce a struct (aka "skeleton") tailored and specific
to a provided BPF object file. This provides an alternative, simplified API
compared to standard libbpf interaction. Also, add libbpf extern variable
resolution for .kconfig section to import Kconfig data, from Andrii Nakryiko.
2) Add BPF dispatcher for XDP which is a mechanism to avoid indirect calls by
generating a branch funnel as discussed back in bpfconf'19 at LSF/MM. Also,
add various BPF riscv JIT improvements, from Björn Töpel.
3) Extend bpftool to allow matching BPF programs and maps by name,
from Paul Chaignon.
4) Support for replacing cgroup BPF programs attached with BPF_F_ALLOW_MULTI
flag for allowing updates without service interruption, from Andrey Ignatov.
5) Cleanup and simplification of ring access functions for AF_XDP with a
bonus of 0-5% performance improvement, from Magnus Karlsson.
6) Enable BPF JITs for x86-64 and arm64 by default. Also, final version of
audit support for BPF, from Daniel Borkmann and latter with Jiri Olsa.
7) Move and extend test_select_reuseport into BPF program tests under
BPF selftests, from Jakub Sitnicki.
8) Various BPF sample improvements for xdpsock for customizing parameters
to set up and benchmark AF_XDP, from Jay Jayatheerthan.
9) Improve libbpf to provide a ulimit hint on permission denied errors.
Also change XDP sample programs to attach in driver mode by default,
from Toke Høiland-Jørgensen.
10) Extend BPF test infrastructure to allow changing skb mark from tc BPF
programs, from Nikita V. Shirokov.
11) Optimize prologue code sequence in BPF arm32 JIT, from Russell King.
12) Fix xdp_redirect_cpu BPF sample to manually attach to tracepoints after
libbpf conversion, from Jesper Dangaard Brouer.
13) Minor misc improvements from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
By re-attaching RX, TX, and CTL rings during connect() rather than
assuming they are freshly allocated (i.e. assuming the counters are zero),
and avoiding forcing state to Closed in netback_remove() it is possible
for vif instances to be unbound and re-bound from and to (respectively) a
running guest.
Dynamic unbind/bind is a highly useful feature for a backend module as it
allows it to be unloaded and re-loaded (i.e. updated) without requiring
domUs to be halted.
This has been tested by running iperf as a server in the test VM and
then running a client against it in a continuous loop, whilst also
running:
while true;
do echo vif-$DOMID-$VIF >unbind;
echo down;
rmmod xen-netback;
echo unloaded;
modprobe xen-netback;
cd $(pwd);
brctl addif xenbr0 vif$DOMID.$VIF;
ip link set vif$DOMID.$VIF up;
echo up;
sleep 5;
done
in dom0 from /sys/bus/xen-backend/drivers/vif to continuously unbind,
unload, re-load, re-bind and re-plumb the backend.
Clearly a performance drop was seen but no TCP connection resets were
observed during this test and moreover a parallel SSH connection into the
guest remained perfectly usable throughout.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On RTL8211F the RX and TX delays (2ns) can be configured in two ways:
- pin strapping (RXD1 for the TX delay and RXD0 for the RX delay, LOW
means "off" and HIGH means "on") which is read during PHY reset
- using software to configure the TX and RX delay registers
So far only the configuration using pin strapping has been supported.
Add support for enabling or disabling the RGMII RX delay based on the
phy-mode to be able to get the RX delay into a known state. This is
important because the RX delay has to be coordinated between the PHY,
MAC and the PCB design (trace length). With an invalid RX delay applied
(for example if both PHY and MAC add a 2ns RX delay) Ethernet may not
work at all.
Also add debug logging when configuring the RX delay (just like the TX
delay) because this is a common source of problems.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII requires a delay of 2ns between the data and the clock signal.
There are at least three ways this can happen. One possibility is by
having the PHY generate this delay.
This is a common source for problems (for example with slow TX speeds or
packet loss when sending data). The TX delay configuration of the
RTL8211F PHY can be set either by pin-strappping the RXD1 pin (HIGH
means enabled, LOW means disabled) or through configuring a paged
register. The setting from the RXD1 pin is also reflected in the
register.
Add debug logging to the TX delay configuration on RTL8211F so it's
easier to spot these issues (for example if the TX delay is enabled for
both, the RTL8211F PHY and the MAC).
This is especially helpful because there is no public datasheet for the
RTL8211F PHY available with all the RX/TX delay specifics.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in previous patches, the driver no longer needs to maintain
a list of identical FIB entries (i.e, same {tb_id, prefix, prefix
length}) and therefore each FIB node can only store one FIB entry.
Remove the FIB entry list and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last patch mlxsw_sp_fib{4,6}_node_entry_link() and
mlxsw_sp_fib{4,6}_node_entry_unlink() are identical and can therefore be
consolidated into the same common function.
Perform the consolidation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Host routes that perform decapsulation of IP in IP tunnels have a
special adjacency entry linked to them. This entry stores information
such as the expected underlay source IP. When the route is deleted this
entry needs to be freed.
The allocation of the adjacency entry happens in
mlxsw_sp_fib4_entry_type_set(), but it is freed in
mlxsw_sp_fib4_node_entry_unlink().
Create a new function - mlxsw_sp_fib4_entry_type_unset() - and free the
adjacency entry there.
This will allow us to consolidate mlxsw_sp_fib{4,6}_node_entry_unlink()
in the next patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the driver no longer maintains a list of identical routes there is
no route to promote when a route is deleted.
Remove that code that took care of it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the networking stack takes care of only notifying the routes of
interest, we do not need to maintain a list of identical routes.
Remove the check that tests if the route is the first route in the FIB
node.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the LACP actor/partner state is now part of the uapi, rename the
3ad state defines with LACP prefix. The LACP prefix is preferred over
BOND_3AD as the LACP standard moved to 802.1AX.
Fixes: 826f66b30c ("bonding: move 802.3ad port state flags to uapi")
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1588 standard defines one step operation for both Sync and
PDelay_Resp messages. Up until now, hardware with P2P one step has
been rare, and kernel support was lacking. This patch adds support of
the mode in anticipation of new hardware developments.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing a PHY node, register its time stamper, if any, and attach
the instance to the PHY device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While PHY time stamping drivers can simply attach their interface
directly to the PHY instance, stand alone drivers require support in
order to manage their services. Non-PHY MII time stamping drivers
have a control interface over another bus like I2C, SPI, UART, or via
a memory mapped peripheral. The controller device will be associated
with one or more time stamping channels, each of which sits snoops in
on a MII bus.
This patch provides a glue layer that will enable time stamping
channels to find their controlling device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the stack supports time stamping in PHY devices. However,
there are newer, non-PHY devices that can snoop an MII bus and provide
time stamps. In order to support such devices, this patch introduces
a new interface to be used by both PHY and non-PHY devices.
In addition, the one and only user of the old PHY time stamping API is
converted to the new interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An upcoming patch will change how the PHY time stamping functions are
registered with the networking stack, and adapting this driver would
entail adding forward declarations for four time stamping methods.
However, forward declarations are considered to be stylistic defects.
This patch avoids the issue by moving the probe and remove methods
immediately above the phy_driver interface structure.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp_ethss driver tests fields of the phy_device in order to
determine whether to defer to the PHY's time stamping functionality.
This patch replaces the open coded logic with an invocation of the
proper methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macvlan layer tests fields of the phy_device in order to determine
whether to invoke the PHY's tsinfo ethtool callback. This patch
replaces the open coded logic with an invocation of the proper
methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mlxsw is converted to use the new FIB notifications it is
possible to delete the old ones and use the new replace / append /
delete notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new notifications mlxsw does not need to handle identical
routes itself, as this is taken care of by the core IPv6 code.
Instead, mlxsw only needs to take care of inserting and removing routes
from the device.
Convert mlxsw to use the new IPv6 route notifications and simplify the
code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code by moving the call to rtl_enable_eee() from the
individual PHY configs to rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to recent changes we don't need the call to rtl_rar_exgmac_set()
and longer at this place. It's called from rtl_rar_set() which is
called in rtl_init_mac_address() and rtl8169_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and factor out this magic from rtl8168h_2_hw_phy_config()
and name it based on the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
Correct a mismatch between rx_page_buf_step and the actual step size
used when filling buffer pages.
This patch fixes the page overrun that occured when the MTU was set to
anything bigger than 1692.
Fixes: 3990a8fffb ("sfc: allocate channels for XDP tx queues")
Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible for channel allocation logic to get confused between what
it had and what it wanted, and end up trying to use the same channel for
both PTP and regular TX. This led to a kernel panic:
BUG: unable to handle page fault for address: 0000000000047635
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.4.0-rc3-ehc14+ #900
Hardware name: Dell Inc. PowerEdge R710/0M233H, BIOS 6.4.0 07/23/2013
RIP: 0010:native_queued_spin_lock_slowpath+0x188/0x1e0
Code: f3 90 48 8b 32 48 85 f6 74 f6 eb e8 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 05 48 63 f6 48 05 c0 98 02 00 48 03 04 f5 a0 c6 ed 81 <48> 89 10 8b 42 08 85 c0 75 09 f3 90 8b 42 08 85 c0 74 f7 48 8b 32
RSP: 0018:ffffc90000003d28 EFLAGS: 00010006
RAX: 0000000000047635 RBX: 0000000000000246 RCX: 0000000000040000
RDX: ffff888627a298c0 RSI: 0000000000003ffe RDI: ffff88861f6b8dd4
RBP: ffff8886225c6e00 R08: 0000000000040000 R09: 0000000000000000
R10: 0000000616f080c6 R11: 00000000000000c0 R12: ffff88861f6b8dd4
R13: ffffc90000003dc8 R14: ffff88861942bf00 R15: ffff8886150f2000
FS: 0000000000000000(0000) GS:ffff888627a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000047635 CR3: 000000000200a000 CR4: 00000000000006f0
Call Trace:
<IRQ>
_raw_spin_lock_irqsave+0x22/0x30
skb_queue_tail+0x1b/0x50
sock_queue_err_skb+0x9d/0xf0
__skb_complete_tx_timestamp+0x9d/0xc0
efx_dequeue_buffer+0x126/0x180 [sfc]
efx_xmit_done+0x73/0x1c0 [sfc]
efx_ef10_ev_process+0x56a/0xfe0 [sfc]
? tick_sched_do_timer+0x60/0x60
? timerqueue_add+0x5d/0x70
? enqueue_hrtimer+0x39/0x90
efx_poll+0x111/0x380 [sfc]
? rcu_accelerate_cbs+0x50/0x160
net_rx_action+0x14a/0x400
__do_softirq+0xdd/0x2d0
irq_exit+0xa0/0xb0
do_IRQ+0x53/0xe0
common_interrupt+0xf/0xf
</IRQ>
In the long run we intend to rewrite the channel allocation code, but for
'net' fix this by allocating extra_channels, and giving them TX queues,
even if we do not in fact need them (e.g. on NICs without MAC TX
timestamping), and thereby using simpler logic to assign the channels
once they're allocated.
Fixes: 3990a8fffb ("sfc: allocate channels for XDP tx queues")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.6. The biggest thing here is of course the
new driver ath11k but also new features for other drivers as well a
myriad of bug fixes.
Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
brcmfmac
* add support for BCM4359 SDIO chipset
wil6210
* support set_multicast_to_unicast cfg80211 operation
* support set_cqm_rssi_config cfg80211 operation
wcn36xx
* disable HW_CONNECTION_MONITOR as firmware is buggy
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd/OTiAAoJEG4XJFUm622bN3MH+gM/uwAyMUOLK/x+9dyL+nnO
y8/QbtkM9eyMaMJ+8BoA4XVs8Md5K0YPEUoV22VoTKXgRLX5G2dwoFC5TbuuIxGF
6ptojEoc6XsYYOySHGlgEwPhR8UYf3YfvpgerqbENeiCA82ZHrY9MSUEReEGLr6U
OSb+qcP1KtwpIvo8u4hhomJQO4vO1iY+Z1+6tUzDzpzk3t/rsX2dg9083Cw46JgT
deruvZziwFLsws4EVoBUxa9OPg4Jz/zelRlgHpAXi4VWr7GM9p2cqTia0OwE/coX
VCberklKTJLQfpp5L3uZ9QX4MwSwhTJC/rPiwm9a+4TezT7yVAexF2Q+L/nKKRQ=
=nRvm
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
First set of patches for v5.6. The biggest thing here is of course the
new driver ath11k but also new features for other drivers as well a
myriad of bug fixes.
Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
brcmfmac
* add support for BCM4359 SDIO chipset
wil6210
* support set_multicast_to_unicast cfg80211 operation
* support set_cqm_rssi_config cfg80211 operation
wcn36xx
* disable HW_CONNECTION_MONITOR as firmware is buggy
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In existing code, the receive indirection table, rx_table, is in
struct rndis_device, which will be reset when changing MTU, ringparam,
etc. User configured receive indirection table values will be lost.
To fix this, move rx_table to struct net_device_context, and check
netif_is_rxfh_configured(), so rx_table will be set to default only
if no user configured value.
Fixes: ff4a441990 ("netvsc: allow get/set of RSS indirection table")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY IDs are 32-bit unsigned quantities. Ensure that they are always
treated as such, and not passed around as "int"s.
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 18c602dee4 ("qede: Use NETIF_F_GRO_HW.") introduced
a regression in driver that when xdp program is installed on
qede device, device's aggregation feature (hardware GRO) is not
getting disabled, which is unexpected with xdp.
Fixes: 18c602dee4 ("qede: Use NETIF_F_GRO_HW.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue 1:
--------
Reproduction steps:
1. sudo ethtool -C eth0 rx-usecs 128
2. sudo ethtool -C eth0 adaptive-rx on
3. sudo ethtool -C eth0 adaptive-rx off
4. ethtool -c eth0
expected output: rx-usecs 128
actual output: rx-usecs 0
Reason for issue:
In stage 3, ethtool userspace calls first the ena_get_coalesce() handler
to get the current value of all properties, and then the ena_set_coalesce()
handler. When ena_get_coalesce() is called the adaptive interrupt
moderation is still on. There is an if in the code that returns the
rx_coalesce_usecs only if the adaptive interrupt moderation is off.
And since it is still on, rx_coalesce_usecs is not set, meaning it
stays 0.
Solution to issue:
Remove this if static interrupt moderation intervals have nothing to do
with dynamic ones.
Issue 2:
--------
Reproduction steps:
1. sudo ethtool -C eth0 adaptive-rx on
2. sudo ethtool -C eth0 rx-usecs 128
3. ethtool -c eth0
expected output: rx-usecs 128
actual output: rx-usecs 0
Reason for issue:
In stage 2, when ena_set_coalesce() is called, the handler tests if
rx adaptive interrupt moderation is on, and if it is, it returns before
getting to the part in the function that sets the rx non-adaptive
interrupt moderation interval.
Solution to issue:
Remove the return from the function when rx adaptive interrupt moderation
is on.
Also cleaned up the fixed code in ena_set_coalesce by grouping together
adaptive interrupt moderation toggling, and using && instead of nested
ifs.
Fixes: b3db86dc4b ("net: ena: reimplement set/get_coalesce()")
Fixes: 0eda847953 ("net: ena: fix retrieval of nonadaptive interrupt moderation intervals")
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current default non-adaptive tx interrupt moderation interval is 196 us.
This value is too high and might cause the tx queue to fill up.
In this commit we set the default non-adaptive tx interrupt moderation
interval to 64 us in order to:
1. Reduce the probability of the queue filling-up (when compared to the
current default value of 196 us).
2. Reduce unnecessary tx interrupt overhead (which happens if we set the
default tx interval to 0).
We determined experimentally that 64 us is an optimal value that
reduces interrupt rate by more than 20% without affecting performance.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of "stmmac_dt_phy" function initializes
the MDIO platform bus data, even in the absence of PHY. This fix
will skip MDIO initialization if there is no PHY present.
Fixes: 7437127 ("net: stmmac: Convert to phylink and remove phylib logic")
Acked-by: Jayati Sahu <jayati.sahu@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Signed-off-by: Padmanabhan Rajanbabu <p.rajanbabu@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing misc interrupt status of hardware error event in the
IRQ handler is unnecessary, since hclge_handle_hw_msix_error()
will print out the detail information for this hardware error
when handling success. So, this patch removes the print in
IRQ handler, and prints it when hclge_handle_hw_msix_error()
fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
