This patch introduces the RX checksum function to check the
status of the hardware calculated checksum and its error and
appropriately convey status to the upper stack in skb->ip_summed
field.
In hardware, we only support checksum for the following
protocols:
1) IPv4,
2) TCP(over IPv4 or IPv6),
3) UDP(over IPv4 or IPv6),
4) SCTP(over IPv4 or IPv6)
but we support many L3(IPv4, IPv6, MPLS, PPPoE etc) and
L4(TCP, UDP, GRE, SCTP, IGMP, ICMP etc.) protocols.
Hardware limitation:
Our present hardware RX Descriptor lacks L3/L4 checksum
"Status & Error" bit (which usually can be used to indicate whether
checksum was calculated by the hardware and if there was any error
encountered during checksum calculation).
Software workaround:
We do get info within the RX descriptor about the kind of
L3/L4 protocol coming in the packet and the error status. These
errors might not just be checksum errors but could be related to
version, length of IPv4, UDP, TCP etc.
Because there is no-way of knowing if it is a L3/L4 error due
to bad checksum or any other L3/L4 error, we will not (cannot)
convey hardware checksum status(CHECKSUM_UNNECESSARY) for such
cases to upper stack and will not maintain the RX L3/L4 checksum
counters as well.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support to add or remove the unicast entries
to the table and remove from the table.
Reported-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no clear operation before add a new multicast tcam table,
so the tcam table will be overflow when add more entries.
Reported-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware ring buffer data is stored in Little-endian. Thus cpu data
should be modified to Little-endian.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is PORT_TP type if the service port is GE mode. It is wrong to
judge the port type by using if it is service port. Adding the media
type to know port type.
Reported-by: Jinchuan Tian <tianjinchuan1@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When network interface is enabled, the ring enable operation is
conducted twice. This patch deletes the redundancy code of ring enable,
and integrates hnae_ae_ops.toggle_queue_status other functions to
hns_ae_start.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds get_coalesce_range api for hns, it shows
range of coalesce usecs and frames that can be set on
this interface.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As device_node is only used by DT case, HNS needs to treat the other
cases including ACPI. It needs to use uniform ways to handle both of
DT and ACPI. This patch chooses phy_device, and of_phy_connect and
of_phy_attach are only used by DT case. It needs to use uniform interface
to handle that sequence by both DT and ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As device_node is only used by DT case, it is expected to find uniform
ways. So fwnode_handle is the suitable method.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may fail to set coalesce usecs to HW, and Ethtool needs to know if it
is successful to cfg the parameter or not. So it needs return the errno by
dsaf.ko.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In chip V2, the default value of port id in tx BD is Zero. If it is not
configurated to the other value, all management packets will be sent out
from port0. So port_id in the tx BD needs to be updated when sending a
management packet.
In V2 chip, when sending mamagement packets, the driver should
config the port id to BD descs.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace the assoication between dsaf and enet from string
matching to object reference. It requires the DTS to be updated within
BIOS. Thanks god it can be done for all released boards.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
here is the patch raising the performance of XGE by:
1)changes the way page management method for enet momery, and
2)reduces the count of rmb, and
3)adds Memory prefetching
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of "TSO (TCP Segment Offload)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
Enabling this feature would help offload the TCP Segmentation
process to the Hip06 ethernet hardware. This eventually would help
in saving precious cpu cycles.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of "RSS (Receive Side Scaling)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
This feature helps in distributing the different flows (mapped as
hash by hardware using Toeplitz Hash) to different Queues asssociated
with the processor cores. The mapping of flow-hash values to the
different queues is stored in indirection table (which is per Packet-
parse-Engine/PPE). This patch also provides the changes to re-program
the (flow-hash<->Qid) mapping using the ethtool.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset adds support of Hisilicon Hip06 SoC to the existing HNS
ethernet driver.
The changes in the driver are mainly due to changes in the DMA
descriptor provided by the Hip06 ethernet hardware. These changes
need to co-exist with already present Hip05 DMA descriptor and its
operating functions. The decision to choose the correct type of DMA
descriptor is taken dynamically depending upon the version of the
hardware (i.e. V1/hip05 or V2/hip06, see already existing
hisilicon-hns-nic.txt binding file for detailed description). other
changes includes in SBM, DSAF and PPE modules as well. Changes
affecting the driver related to the newly added ethernet hardware
features in Hip06 would be added as separate patch over this and
subsequent patches.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds support to set promisc mode. it configs the queue on
init seq when it is on promisc mode.and being enabled or disabled promisc
mode by upper level user.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the building error reported by Jiri Pirko <jiri@resnulli.us>
drivers/net/ethernet/hisilicon/hns/hnae.h:465:2: error: unknown type
name 'phy_interface_t'
phy_interface_t phy_if;
^
the full build log is on https://lists.01.org/pipermail/kbuild-all.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNAE (Hisilicon Network Acceleration Engine) is a framework to provide a
unified ring buffer interface for Hisilicon Network Acceleration
Engines.
With the interface, upper layer can work as ethernet driver, ODP driver
or other service driver on purpose.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
