We don't have any arch specific scatterlist now that parisc switched over
to the generic one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We've got a fairly large cleanup branch this time. The bulk of this is removal
of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining board-file based
support
- OMAP removes legacy board files for three more platforms
- Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
- Freescale i.MX25 also removes non-DT platform support
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNzI3AAoJEIwa5zzehBx3ePwQAJKb4Mf72/4iiKb4dbVcooQN
EiZ84fwWiWD6Mww/3A76xVnz/b7JWmB3vwW0b4fcbvzubmOjnROBmZgCWeNy4ZTv
dOZc3/9jK7OrlwvpFBeZykQwHcbz+550+m3WxmLft1oqH/7BA1k5aunwYtFB96ii
5Owi4Cy9OmxEyALQAvzktFaJdI7J66LNb+i30r5zIZHlkVooeF3UyadndiswUP2o
EBzCE8UPqRi5kV6FuwVyf4MZaV28FWoglTqdx9OxogcTnKNFT6RlHQ39q/iPu348
Wkh4kOryVy7Rlab1K4wQRpBoOwkonKDV73u2H2ifRFj7V9ZAdjibK8pgKn3kjkba
bJkwHIqlqtqqqjj2Hh93wl+8hKSypoLXO9tagPWYBiLtFXCH/+EVsihWYpAc/A5E
pUS6hJrJyXKJouwwsXu6459zP0ieqhvpbQG72xs9PRimAfAdSTulSTzdI/dMh42Q
pwYkmvh+ReY3Ll4MeCzu7+eCIY0qAKsor48W1ImuziwQhg2lZj16qWtA4YdPk3+O
N8ckyaaFg663PAfsZgBx1qTgxw5v0ec2k68/iEVGS5mUJCgcWxFvR95chTDIxQXq
ZmJ+SuMFyLB/2zVSiGU96L1PQTcUkxJJ8LVB3qNp6KlYT7qUSsgAU+qYveFlUh+p
X8MVsSVh8n1MTNepsLij
=BV8A
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
This reverts commit 6685ac62b2 ("mmc: core: Convert mmc_driver to
device_driver")
The reverted commit went too far in simplifing the device driver parts
for mmc.
Let's restore the old mmc_driver to enable driver core to sooner
or later to remove the ->probe(), ->remove() and ->shutdown() callbacks
from the struct device_driver.
Note that, the old ->suspend|resume() callbacks in the struct
mmc_driver don't need to be restored, since the mmc block layer has
converted to the modern system PM ops.
Fixes: 6685ac62b2 ("mmc: core: Convert mmc_driver to device_driver")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
If the struct mmc_pwrseq_match .alloc function used to allocate a
struct mmc_pwrseq fails, the error is propagated to mmc_of_parse().
But instead of returning the error code in pwrseq, host->pwrseq is
returned which will always be 0. So mmc_of_parse() succeeds even if
the pwrseq .alloc function failed and host->pwrseq is NULL.
This makes the SDIO device to not be powered if the power sequencing
.alloc functions wants to be deferred due a missing resource because
the mmc controller driver probe did wrongly succeed.
Fixes: 0f12a0ce4c ("mmc: pwrseq: simplify alloc/free hooks")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is the usual grab bag of driver updates (lpfc, qla2xxx, storvsc, aacraid,
ipr) plus an assortment of minor updates. There's also a major update to
aic1542 which moves the driver into this millenium.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVL/DEAAoJEDeqqVYsXL0MOwgIALPlgI0aMAtX5wLxzPMLB/2j
fhNlsB9XZ6TeYIqE7syOY7geVJqsbACMGmDhGHs5Gt6jkTnwix/G49x3T1PXBODZ
frz8GgNB6iGSqfCp+YbhJkTNHdudDIy2LrQ92EzNMb2+x0v6KTYTSq2dekgrC1zK
8GUZ9bEzuxEGaBx9TK/Sy6H8QpvMtqqJig2eCL189U3JMMU3okWtSGya708u5Whh
knbUgraMxFWNs+oHJHFclVYvekP+61i/TVyacQEM4KLDsmlxsLn49eRdiGMY6rpX
LgDIvMjggQhbY2WcCXzetF7tsFFl0joJp1wFK1fUn9YN5e+J3MRWYVBDt8FMPX8=
=OBny
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, qla2xxx, storvsc,
aacraid, ipr) plus an assortment of minor updates. There's also a
major update to aic1542 which moves the driver into this millenium"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (106 commits)
change SCSI Maintainer email
sd, mmc, virtio_blk, string_helpers: fix block size units
ufs: add support to allow non standard behaviours (quirks)
ufs-qcom: save controller revision info in internal structure
qla2xxx: Update driver version to 8.07.00.18-k
qla2xxx: Restore physical port WWPN only, when port down detected for FA-WWPN port.
qla2xxx: Fix virtual port configuration, when switch port is disabled/enabled.
qla2xxx: Prevent multiple firmware dump collection for ISP27XX.
qla2xxx: Disable Interrupt handshake for ISP27XX.
qla2xxx: Add debugging info for MBX timeout.
qla2xxx: Add serdes read/write support for ISP27XX
qla2xxx: Add udev notification to save fw dump for ISP27XX
qla2xxx: Add message for sucessful FW dump collected for ISP27XX.
qla2xxx: Add support to load firmware from file for ISP 26XX/27XX.
qla2xxx: Fix beacon blink for ISP27XX.
qla2xxx: Increase the wait time for firmware to be ready for P3P.
qla2xxx: Fix crash due to wrong casting of reg for ISP27XX.
qla2xxx: Fix warnings reported by static checker.
lpfc: Update version to 10.5.0.0 for upstream patch set
lpfc: Update copyright to 2015
...
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
The current string_get_size() overflows when the device size goes over
2^64 bytes because the string helper routine computes the suffix from
the size in bytes. However, the entirety of Linux thinks in terms of
blocks, not bytes, so this will artificially induce an overflow on very
large devices. Fix this by making the function string_get_size() take
blocks and the block size instead of bytes. This should allow us to
keep working until the current SCSI standard overflows.
Also fix virtio_blk and mmc (both of which were also artificially
multiplying by the block size to pass a byte side to string_get_size()).
The mathematics of this is pretty simple: we're taking a product of
size in blocks (S) and block size (B) and trying to re-express this in
exponential form: S*B = R*N^E (where N, the exponent is either 1000 or
1024) and R < N. Mathematically, S = RS*N^ES and B=RB*N^EB, so if RS*RB
< N it's easy to see that S*B = RS*RB*N^(ES+EB). However, if RS*BS > N,
we can see that this can be re-expressed as RS*BS = R*N (where R =
RS*BS/N < N) so the whole exponent becomes R*N^(ES+EB+1)
[jejb: fix incorrect 32 bit do_div spotted by kbuild test robot <fengguang.wu@intel.com>]
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Some additional quirks need to be enabled now we support UHS
modes. This avoids some spurious warnings like
"Got data interrupt 0x00000002 even though no data operation was in progress"
Testing on stih410-b2120 board achieves the following speeds
with HS200 eMMC card.
max-frequency = 200Mhz
/dev/mmcblk0p1:
Timing buffered disk reads: 270 MB in 3.02 seconds = 89.54 MB/sec
max-frequency = 100Mhz
root@debian-armhf:~# hdparm -t /dev/mmcblk0p1
/dev/mmcblk0p1:
Timing buffered disk reads: 210 MB in 3.00 seconds = 70.00 MB/sec
max-frequency = 50Mhz
root@debian-armhf:~# hdparm -t /dev/mmcblk0p1
/dev/mmcblk0p1:
Timing buffered disk reads: 118 MB in 3.00 seconds = 39.28 MB/sec
This is better than the 3.10 kernel which achieves 77.59 MB/sec
at 200Mhz clock (same board/soc/eMMC).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow UHS modes to work properly we need to provide the st specific
set_uhs_signaling callback function. This function differs from the
generic sdhci_set_uhs_signaling callback in that we need to configure
the correct delay depending on the UHS mode, and also set the V18_EN
bit.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
STiH407 family SoC's have glue registers in the flashSS subsystem which
are used to configure the Arasan HC. This patch configures these glue
registers according to what has been specified in the DT.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to the tight timing constraints in some UHS modes, it is required to have
some delay management in the design. Two types of delay management are supported
in the HW: -
1) Static delay management
2) Dynamic delay management
NB: The delay management is only there when eMMC interface is selected.
1: Static delay management: is used to provide PVT dependent static delay on the
clock/data lines to manage setup/hold requirements of the interface. The maximum
delay possible is 3.25ns. These delays are PVT dependent, and thus delay values
applied are not accurate and vary across provcess voltage and temperature range.
Due to this these delays must not be used on the very time critical paths.
2. Dynamic delay locked loop (DLL): is used to provide dynamic delay management.
The advantage of DLL is that it provides accurate & PVT indepedent delay.
The DLL is used to provide delay on the loopback clock on "Read Path" to capture
read data reliably. On TX path the clock on which output data is transmitted is
delayed, resulting in delay of TX data.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
STiH407 family SoC's can have a reset signal for the controller which needs to
be managed. Also the eMMC controller has some additional 'top' memory mapped
registers which are used to manage the dynamic and static delay required for
UHS modes. This patch adds support for creating the mapping, which will be used
by subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The stih407 family SoC's have additional glue registers in the flashSS which
are used to configure the Arasan controller.
This patch adds macros for the register offsets and bitfields which will be
used by subsequent patches to support stih407 family SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently it is not possible to use 'mmc-pwrseq-simple' property with this
driver because mmc_of_parse() is never called.
mmc_of_parse() calls mmc_pwrseq_alloc() that manages MMC power sequence and
allows passing GPIOs in the devicetree to properly power/reset the Wifi
chipset.
When using mmc_of_parse() we no longer need to have custom code to request
card-detect and write-protect pins, as this can now be handled by the mmc
core.
Tested on a imx6sl-warp board where BT/Wifi is functional and also on a
imx6q-sabresd.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible for the cmd11 interrupt to fire and delete the
cmd11_timer before the cmd11_timer was actually setup. Let's fix this
race by adding a few spinlocks. Note that the race wasn't seen in
practice without adding some printk statements, but it still seems
wise to fix.
Fixes: 5c935165da ("mmc: dw_mmc: Add a timeout for sending CMD11")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we get an unexpected cmd11 timeout we shouldn't actually treat it
as a timeout (not that we really expect to get an unexpected cmd11
timeout, but still).
Fixes: 5c935165da ("mmc: dw_mmc: Add a timeout for sending CMD11")
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Although the cmd11 interrupt should come within 2ms, that's a very
short time. Let's increase the timeout to be really sure that we
don't get an accidnetal timeout. One case in particular this is
useful is if you've got a serial console and printk in just the right
places. Under that scenario I've seen delays of up to 130ms before
the interrupt fired.
CMD11 is only sent during card insertion, so this extra timeout
shouldn't be terrible.
Fixes: 5c935165da ("mmc: dw_mmc: Add a timeout for sending CMD11")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver changes to make the IO accesors endian agnostic did not
take into account the fifo accesses do not need to be swapped. To fix this
add a mmci_fifo_read/write wrapper to allow these to be passed through the
IO without being swapped.
Since these are now specific functions, it would be easier just to store
the pointer to the fifo registers in the host block instead of the offset
to them. So change the host->data_offset to host->fifo_reg (which also
means we catch all the places this is read or written).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver does not take into account the processor may be in
big endian when writing the descriptors. Change the descriptors for
the 32bit IDMA to use __le32 and ensure they are suitably swapped
before writing.
Note, this has not been tested as the socfpga driver does not try to
use idma.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver does not use endian agnostic IO accessors, so fix
the use of __raw reads and writes to be the relaxed versions.
This fixes the dw_mmc driver initialisation on Altera socfpga in big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Also check MMC OF properties. The controller supports MMC too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eMMC on a tablet I've will stop working / communicating as soon as
the kernel executes:
mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
EXT_CSD_HPI_MGMT, 1,
card->ext_csd.generic_cmd6_time);
There seems to be no way to reliable identify eMMC-s which have a broken
hpi implementation, but at least for eMMC's which are soldered onto a board
we can work around this by specifying that hpi is broken in devicetree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
strip the card dectet logic from cover detect isr and vice versa
the generic mmc_gpio_cd_irqt isr, uses 200ms on removal/insertion,
hence that should be fine here as well
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If dw_mci_init_slot() returns that we got a probe deferral then it may
leave slot->mmc as NULL. That will cause dw_mci_enable_cd() to crash
when it calls mmc_gpio_get_cd().
Fix this by moving the call of dw_mci_enable_cd() until we're sure
that we're good. Note that if we have more than one slot and one
defers (but the others don't) things won't work so well. ...but
that's not a new thing and everyone has already agreed that multislot
support ought to be removed from dw_mmc eventually anyway since it is
unused, untested, and you can see several bugs like this by inspecting
the code.
Fixes: bcafaf5470f0 ("mmc: dw_mmc: Only enable CD after setup and only if needed")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the Designware databook's description of the "Voltage Switch Normal
Scenario" it instructs us to set a timer and fail the voltage change
if we don't see the voltage change interrupt within 2ms. Let's
implement that. Without implementing this I have often been able to
reproduce a hang while trying to send CMD11 on an rk3288-based board
while constantly ejecting and inserting UHS cards.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently those host drivers which have deployed runtime PM, deals with
the runtime PM reference counting entirely by themselves.
Since host drivers don't know when the core will send the next request
through some of the host_ops callbacks, they need to handle runtime PM
get/put between each an every request.
In quite many cases this has some negative effects, since it leads to a
high frequency of scheduled runtime PM suspend operations. That due to
the runtime PM reference count will normally reach zero in-between
every request.
We can decrease that frequency, by enabling the core to deal with
runtime PM reference counting of the host device. Since the core often
knows that it will send a seqeunce of requests, it makes sense for it
to keep a runtime PM reference count during these periods.
More exactly, let's increase the runtime PM reference count by invoking
pm_runtime_get_sync() from __mmc_claim_host(). Restore that action by
invoking pm_runtime_mark_last_busy() and pm_runtime_put_autosuspend()
in mmc_release_host(). In this way a runtime PM reference count will be
kept during the complete cycle of a claim -> release host.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Konstantin Dorfman <kdorfman@codeaurora.org>
This driver is orphaned now that mach-msm has been removed.
Delete it.
Cc: Chris Ball <chris@printf.net>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
board-rx51 has no card detect pin in the mmc slot, but can detect that
the (cell-phone) cover has been removed and the card is accessible.
The semantics between cover/card detect differ, the gpio on the slot
informs you after the card has been removed, cover removal does not
necessarily mean that the card has been removed.
This means different code paths are necessary. To complete this we
also want different fields in the platform data for cover and card
detect. This separation is not pushed all the way down into struct
omap2_hsmmc_info which is used to initialize the platform data.
If we did that we had to go over all board files and set the new
gpio_cod pin to -EINVAL. If we forget one board or some out-of-tree
archicture forgets that the default '0' is used which is a valid pin
number.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These callbacks have been set to deprecated for some time. The last
user (omap_hsmmc) has moved away from using them, which thus enables
us to completely remove them.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ->enable|disable() callbacks are only used to get and put runtime
PM references. Currently omap_hsmmc's ->set_ios() already does this
itself.
Other host drivers deals with runtime PM without using the
->enable|disable() callbacks and thus do the runtime PM reference
counting themselves. Apply that approach for omap_hsmmc as well and
then discard the ->enable|disable() callbacks.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some versions of this controller do not advertise their 3.0v and
8bit bus-width support capabilities. It is required to explicitly
set these capabilities for the specific controller versions.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the __raw IO functions to endian agnostic relaxed ones to allow
the driver to function on big endian ARM systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the MXC MMUC driver is used on a Freescale MPC512x machine, it
contains some additional byteswapping code (I'm assuming this is a
workaround for a hardware defect). This uses the ppc specific st_le32()
function, but there's no reason not to use the generic swab32() function
instead. gcc is capable of generating the efficient ppc byte-reversing
load/store instructions without the arch-specific helper.
This patch, therefore, switches to the generic byteswap routine.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Every call to sdio_enable_4bit_bus is followed (on success) by a call
to mmc_set_bus_width().
To simplify the code, include those calls directly in
sdio_enable_4bit_bus().
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the sunxi mmc-controller code was initially merged MMC_CAP_SDIO_IRQ was
not added to the host caps because of issues with some sdio wifi modules.
It turns out that these issues have nothing to do with using sdio-irq support,
they also happen with oob interrupts. Since the hardware supports sdio-irq
everywhere, and since the one reason to not claim the capability is gone,
add MMC_CAP_SDIO_IRQ to the default host caps.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver co-allocates sdhci_iproc_host with sdhci_pltfm_host and so to
access it we need to use sdhci_pltfm_priv() and not pltfm_host->priv.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_request function should consider a non-removable device
always present.
Call the correct logic already available in sdhci_do_get_cd function.
This fixes some logic paths where MMC requests are being made to
non-removable devices that do not have the card detect pin connected
on the hardware as it is non-removable.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the member for card_int_gpio into the struct spear_sdhci.
In this way we eliminate the last user of the struct sdhci_plat_data,
which enables us to remove the exported header for sdhci-spear.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is used on SoCs which are using CONFIG_OF. By adding a
compile dependency in the Kconfig, it enables us to simplify some code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since there no users of the struct sdhci_host, but the shdci host
drivers themselves, let's move the definition of it to the local sdhci
header.
The exported sdhci header then becomes empty, so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
