We are currently writing the same register twice. Let's enable the USB
PHY only at the end of the function.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When docked to a Motorola lapdock or media dock, we're in USB A-host mode
with VBUS provided by the dock. When in regular USB A-host mode, we're
providing the VBUS. And in regular USB A-host mode we must also keep
kicking the VBUS to keep it active.
Let's wait a bit before configuring the USB PHY to allow some time between
the ID and VBUS changes. And let's add vbus_provider flag so we can detect
docked mode and regularo USB A-host mode better.
With better USB A-host mode detection, we can now also just kick the
VBUS to keep it enabled and leave out the unnecessary line muxing.
We only need to set and clear vbus_provider in the delayed work so no
locking is needed for it currently.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The micro-USB connector on Motorola Mapphone devices can be muxed between
the SoC and the mdm6600 modem. But even when used for the SoC, configuring
the PHY with ID pin grounded will wake up the modem from idle state. Looks
like the issue is probably caused by line glitches.
We can prevent the glitches by using a previously unknown mode of the
GPIO mux to prevent the USB lines from being connected to the moden while
configuring the USB PHY, and enable the USB lines after configuring the
PHY.
Note that this only prevents waking up mdm6600 as regular USB A-host mode,
and does not help when connected to a lapdock. The lapdock specific issue
still needs to be debugged separately.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Only the used bits get cleared with bitmap_zero() when we call
gpiod_get_array_value_cansleep(). We must mask only the bits we're
using for ddata->status as the other bits in the bitmap may not be
initialized.
And let's also drop useless debug code accidentally left over while
at it.
Fixes: b9762bebc6 ("gpiolib: Pass bitmaps, not integer arrays, to get/set array")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We must let the USB host idle things properly before we switch to debug
UART mode. Otherwise the USB host may never idle after disconnecting
devices, and that causes the next enumeration to be flakey.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It's typical for the QHP PHY to take slightly above 1ms to initialize,
so increase the timeout of the PHY ready check to 10ms - as already done
in the downstream PCIe driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Evan Green <evgreen@chromium.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver calls clk_prepare_enable in probe but the corresponding
clk_disable_unprepare() is in ti_pipe3_disable_clocks().
Move clk_disable_unprepare() to remove to make them symmetric.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch corrects the SPDX License Identifier style in
header files related to PHY drivers for Qualcomm platforms.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If musb_mailbox() returns an error, we must still continue to finish
configuring the phy.
Otherwise the phy state may end up only half initialized, and this can
cause the debug serial console to stop working. And this will happen if the
usb driver musb controller is not loaded.
Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox().
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6ewA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymNXACfebVkDrFOH9EqDgFArPvZ1i9EmZ4AoLbE1Wki
ftJApk+Ov1BT2TvClOza
=cXqg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
char: Fix Kconfig indentation, continued
habanalabs: add more protection of device during reset
habanalabs: flush EQ workers in hard reset
habanalabs: make the reset code more consistent
habanalabs: expose reset counters via existing INFO IOCTL
habanalabs: make code more concise
habanalabs: use defines for F/W files
habanalabs: remove prints on successful device initialization
habanalabs: remove unnecessary checks
habanalabs: invalidate MMU cache only once
habanalabs: skip VA block list update in reset flow
habanalabs: optimize MMU unmap
habanalabs: prevent read/write from/to the device during hard reset
habanalabs: split MMU properties to PCI/DRAM
habanalabs: re-factor MMU masks and documentation
habanalabs: type specific MMU cache invalidation
habanalabs: re-factor memory module code
habanalabs: export uapi defines to user-space
habanalabs: don't print error when queues are full
habanalabs: increase max jobs number to 512
...
Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd5+Iw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylA4wCbB3P206oHeHLBe9Eika3D8gM9/fMAn2oWlmpB
Xh7wr30FGC02zU/KBpJ1
=U5qC
-----END PGP SIGNATURE-----
Merge tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues"
* tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
usb: gadget: udc: gr_udc: create debugfs directory under usb root
usb: gadget: atmel: create debugfs directory under usb root
usb: musb: create debugfs directory under usb root
usb: serial: Fix Kconfig indentation
usb: misc: Fix Kconfig indentation
usb: gadget: Fix Kconfig indentation
usb: host: Fix Kconfig indentation
usb: dwc3: Fix Kconfig indentation
usb: gadget: configfs: Fix missing spin_lock_init()
usb-storage: Disable UAS on JMicron SATA enclosure
USB: documentation: flags on usb-storage versus UAS
USB: uas: heed CAPACITY_HEURISTICS
USB: uas: honor flag to avoid CAPACITY16
usb: host: xhci-tegra: Correct phy enable sequence
usb-serial: cp201x: support Mark-10 digital force gauge
usb: chipidea: imx: pinctrl for HSIC is optional
usb: chipidea: imx: refine the error handling for hsic
usb: chipidea: imx: change hsic power regulator as optional
usb: chipidea: imx: check data->usbmisc_data against NULL before access
usb: chipidea: core: change vbus-regulator as optional
...
Add dependency from TI_CPSW_SWITCHDEV.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The px30 soc from Rockchip shares the same register description as
the rk3328, so can re-use its definitions.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
switched from extcon_register_notifier() to the resource-managed
API, i.e. devm_extcon_register_notifier().
This is problematic in this case, because the extcon notifier
is dynamically registered/unregistered whenever the PHY is powered
on/off. The resource-managed API does not unregister the notifier
until the driver is removed, so as soon as the PHY is power cycled,
attempting to register the notifier again results in:
double register detected
WARNING: CPU: 1 PID: 182 at kernel/notifier.c:26 notifier_chain_register+0x74/0xa0
Call trace:
...
extcon_register_notifier+0x74/0xb8
devm_extcon_register_notifier+0x54/0xb8
qcom_usb_hs_phy_power_on+0x1fc/0x208
...
... and USB stops working after plugging the cable out and in
another time.
The easiest way to fix this is to make a partial revert of
commit f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
and avoid using the resource-managed API in this case.
Fixes: f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix the below smatch warning by adding variable check rather than the
hardcoded value.
warn: array off by one? 'data->select_value[channel_num]'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: e52a632195 ("phy: lantiq: vrx200-pcie: add a driver for the Lantiq VRX200 PCIe PHY")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Innosilicon Video Combo PHY not only supports MIPI DSI,
but also LVDS and TTL functions with small die size and low
pin count. Customers can choose according to their own applications.
Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com>
[removed TTL mode for now, as it required a hook back into the dsi host]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
controlled).
Add a driver for it.
The register operations in this driver is mainly extracted from the BSP
USB3 driver.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SM8150 UFS PHY is v4 of QMP phy. Add support for V4 QMP phy register
defines and support for SM8150 QMP UFS PHY.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now phy-gmii-sel will disable MAC TX internal delay for PHY interface mode
"rgmii-rxid" which is incorrect.
Hence, fix it by enabling MAC TX internal delay in the case of "rgmii-rxid"
mode.
Fixes: 92b58b3474 ("phy: ti: introduce phy-gmii-sel driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use the new regulator helper instead of a for loop.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/phy/ti/phy-dm816x-usb.c:192:29: warning:
variable phy_data set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 9bb86777fb ("phy: rcar-gen3-usb2: add sysfs for usb role swap")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On Tegra210, usb2 only otg/peripheral ports dont work in device mode.
They need an assosciated usb3 port to work in device mode. Identify
an unused usb3 port and assign it as a fake USB3 port to USB2 only
port whose mode is otg/peripheral.
Based on work by BH Hsieh <bhsieh@nvidia.com>.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Configure the port capabilities based on usb_dr_mode settings.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The xhci_ec_base variable is a pointer, so don't compare
it with an integer.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
As platform_get_irq() now prints an error when the interrupt does not
exist, a scary warning may be printed for an optional interrupt:
phy_rcar_gen3_usb2 ee0a0200.usb-phy: IRQ index 0 not found
Fix this by calling platform_get_irq_optional() instead.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The local variable @priv is set but not used, can be removed
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Don't populate the array serdes_reg on the stack but instead make it
static const. Makes the object code smaller by 228 bytes.
Before:
text data bss dec hex filename
23875 6232 64 30171 75db drivers/phy/phy-xgene.o
After:
text data bss dec hex filename
23551 6328 64 29943 74f7 drivers/phy/phy-xgene.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
As platform_get_irq() now prints an error when the interrupt does not
exist, a scary warning may be printed for an optional interrupt:
phy_rcar_gen3_usb2 ee0a0200.usb-phy: IRQ index 0 not found
Fix this by calling platform_get_irq_optional() instead.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add PHY driver for the USB2 PHY found on Marvell MMP3 SoC.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds extended PCIe PHY functions for the Amlogic G12A
USB3+PCIE Combo PHY to support reset, power_on and power_off for
PCIe exclusively.
With these callbacks, we can handle all the needed operations of the
Amlogic PCIe controller driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Core:
* Ensure HWMON devices are registered with valid names
* Fix device wakeup code
Drivers:
* bq25890_charger: Add BQ25895 support
* axp288_fuel_gauge: Add Minix Neo Z83-4 to blacklist
* sc27xx: improve battery calibration
* misc. small fixes all over drivers
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE72YNB0Y/i3JqeVQT2O7X88g7+poFAl2HhCsACgkQ2O7X88g7
+ppoKw//cPn+LOj1AJYGphqzMz207rJlgn7QFF0a0LhfQHdf6gPtrqVuZ1Mp9+RB
+3aJqp6ORLpKEw7/x8IOlFVACwPRm+ikMqjchb3kYqMZCBuqmr0xYukzxvRWNf/K
LIRkRWMETmaXj1KCIYdFyIt7Ff0HqlXZaFPrgCFK9DO6+wAgoE3LmgZXpya0h5ev
PUYz8MnDjVd5+nkdBDpuBFvpsK66Lg0pZs5ScH1JUKrG6xoXEIU+7VeYJ7EEsfGE
C54g0ZFYLGf+4zxeAyhg9sPb7/tzlM+SChZdUGk6bJ9txgWoalsfNxytb8huSfeK
9dhTVMoZ9seBEq5mfJRUTnmQMRYpLJLWxJjz0MrQotOlSnIN73tlEpuIrUzWl0p7
WIWkYu/hz+OOX0mBBngHXvnTWRQrjO+QIu9P23obFzBedtOL7LVqPtCd5FrJ48y3
xQZAZUyyEUqhq2+HZaTn9HvTbFgnbHmWd/RQDarZcojC+836MlwWC7k3XqkfIa4i
h3P/t6qyc/Kf7o5YT+/TkTpUR5yh2gSwfPGwTQH4hhOxPIN4prC7sF/oySm9tEgw
qLZJ8XP0KuQpBEN8qdhd00bCwEEbDc4+qRJWyjjG0WN2my8BVlzKtrcAVCWspD15
07TV84+OdIzvTXzgWUT1H47WG6RQfpX2rUSCtTwteh710beoctU=
=cIXy
-----END PGP SIGNATURE-----
Merge tag 'for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Ensure HWMON devices are registered with valid names
- Fix device wakeup code
Drivers:
- bq25890_charger: Add BQ25895 support
- axp288_fuel_gauge: Add Minix Neo Z83-4 to blacklist
- sc27xx: improve battery calibration
- misc small fixes all over drivers"
* tag 'for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (24 commits)
power: supply: cpcap-charger: Enable vbus boost voltage
power: supply: sc27xx: Add POWER_SUPPLY_PROP_CALIBRATE attribute
power: supply: sc27xx: Optimize the battery capacity calibration
power: supply: sc27xx: Make sure the alarm capacity is larger than 0
power: supply: sc27xx: Fix the the accuracy issue of coulomb calculation
power: supply: sc27xx: Fix conditon to enable the FGU interrupt
power: supply: sc27xx: Add POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN attribute
power: supply: max77650: add MODULE_ALIAS()
power: supply: isp1704: remove redundant assignment to variable ret
power: supply: bq25890_charger: Add the BQ25895 part
power: supply: sc27xx: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
power: supply: sc27xx: Introduce local variable 'struct device *dev'
power: reset: reboot-mode: Fix author email format
power: supply: ab8500: remove set but not used variables 'vbup33_vrtcn' and 'bup_vch_range'
power: supply: max17042_battery: Fix a typo in function names
power: reset: gpio-restart: Fix typo when gpio reset is not found
power: supply: Init device wakeup after device_add()
power: supply: ab8500_charger: Mark expected switch fall-through
power: supply: sbs-battery: only return health when battery present
MAINTAINERS: N900: Remove isp1704_charger.h record
...
clk registration by clk providers and debugfs "nice to haves" for rate
constraints. I'll highlight that we're now setting the clk_init_data pointer
inside struct clk_hw to NULL during clk_register(), which may break some
drivers that thought they could use that pointer during normal operations. That
change has been sitting in next for a while now but maybe something is still
broken. We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support, new
features for existing drivers, and bug fixes scattered throughout. The biggest
diffstat is the Amlogic driver that gained CPU clk support in addition to
migrating to the new way of specifying clk parents. After that the Qualcomm,
i.MX, Mediatek, and Rockchip clk drivers got support for various new SoCs and
clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6
-----BEGIN PGP SIGNATURE-----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=z8wK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a small collection of core framework updates this time, mostly
around clk registration by clk providers and debugfs "nice to haves"
for rate constraints. I'll highlight that we're now setting the
clk_init_data pointer inside struct clk_hw to NULL during
clk_register(), which may break some drivers that thought they could
use that pointer during normal operations. That change has been
sitting in next for a while now but maybe something is still broken.
We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support,
new features for existing drivers, and bug fixes scattered throughout.
The biggest diffstat is the Amlogic driver that gained CPU clk support
in addition to migrating to the new way of specifying clk parents.
After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
support for various new SoCs and clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: Drop !clk checks in debugfs dumping
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: sprd: add missing kfree
clk: at91: allow 24 Mhz clock as input for PLL
clk: Make clk_bulk_get_all() return a valid "id"
clk: actions: Fix factor clk struct member access
clk: qcom: rcg: Return failure for RCG update
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
...
We are currently not enabling VBUS boost for cpcap when in host mode.
This means the VBUS is fed at the battery voltage level, which can cause
flakeyness enumerating devices.
Looks like the boost control for VBUS is CPCAP_BIT_VBUS_SWITCH that we
must enable in the charger for nice 4.92 V VBUS output. And looks like
we must not use the STBY pin enabling but must instead use manual VBUS
control in phy-cpcap-usb.
We want to do this in cpcap_charger_vbus_work() and also set a flag for
feeding_vbus to avoid races between USB detection and charger detection,
and disable charging if feeding_vbus is set.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The documentation for Marvell's cp110 phy refers to these
registers/register regions as DTL control, DTL frequency loop enable,
etc. This patch aligns the relevant code for these accordingly.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Marvell's cp110 phy supports RXAUI on lanes 2, 3, 4, and 5 when
connected to port zero. When used in this mode, lanes operate in pairs
of two (2 and 3, 4 and 5).
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now that all COMPHY modes are supported by the driver, update the
comment stating that mvebu_comphy_power_off() should be called for
each lane. This is still wrong because for compatibility reasons, it
might break users running an old firmware (the driver only uses SMC
calls for SATA, USB and PCIe configuration, there is no code in Linux
to fallback on in these cases.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add PCIe support by filling the COMPHY modes table.
Also add a new macro to generate the right value for the firmware
depending on the width (PCI x1, x2, x4, etc). The width will be passed
by the core as the "submode" argument of the ->set_mode() callback. If
this argument is zero, default to x1 mode.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Before adding more logic, simplify a bit the writing of the
mvebu_comphy_get_mode() helper by using a pointer instead of
referencing a configuration with the entire table name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the corresponding entries in the COMPHY modes table.
SATA support does not need any additional care.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add USB3 host/device support by adding the right entries in the COMPHY
modes table. A new macro is created to instantiate a "generic" mode
ie. not an Ethernet one. This macro will be re-used when adding SATA
support.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The COMPHY can configure the SERDES lanes in several non-Ethernet
modes: SATA, USB3, PCIe. Drop the condition limiting the driver to
Ethernet modes only before adding support for more.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Before adding support for other PHY modes (not Ethernet ones), let's
rename the MVEBU_COMPHY_CONF macro to a more specific (and shorter)
appellation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for RXAUI mode by adding an entry in the COMPHY modes list.
There is no user for this mode yet so we can enforce an up-to-date
firmware and return an error otherwise without breaking anywone.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently, the driver supports setting lanes to 1000BASEX, 2500BASEX,
10GKR. Complete the COMPHY modes list by adding two (already
supported) cases for lane 4.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Keep the exact same list of supported configurations but first try to
use the firmware's implementation. If it fails, try the legacy method:
Linux implementation.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Explicitly set the lane submode (enum) to a known invalid value.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There is no public clock tree that implies such dependencies between
the MG/MG-core/AXI clocks and the COMPHY IP but accessing the COMPHY
registers while one of the three clocks are disabled stalls the CPU.
This happens if, for instance, the COMPHY driver probe is deferred
(eg. the USB Vbus regulator driver is not yet visible). The MVPP2
driver which also needs these clocks (among others) will
prepare/enable the clocks, then be deferred, and disable/unprepare
them. Next COMPHY lane to be configured would produce an infinite
stall.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
After commit "linux/bits.h: Add compile time sanity check of GENMASK
inputs" [1], arm64 defconfig builds started failing:
In file included from ../include/linux/bits.h:22,
from ../include/linux/bitops.h:5,
from ../include/linux/kernel.h:12,
from ../include/linux/clk.h:13,
from ../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:9:
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c: In function 'inno_hdmi_phy_rk3328_power_on':
../include/linux/build_bug.h:16:45: error: negative width in bit-field '<anonymous>'
16 | #define BUILD_BUG_ON_ZERO(e) (sizeof(struct { int:(-!!(e)); }))
| ^
../include/linux/bits.h:24:18: note: in expansion of macro 'BUILD_BUG_ON_ZERO'
24 | ((unsigned long)BUILD_BUG_ON_ZERO(__builtin_choose_expr( \
| ^~~~~~~~~~~~~~~~~
../include/linux/bits.h:39:3: note: in expansion of macro 'GENMASK_INPUT_CHECK'
39 | (GENMASK_INPUT_CHECK(high, low) + __GENMASK(high, low))
| ^~~~~~~~~~~~~~~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:24:42: note: in expansion of macro 'GENMASK'
24 | #define UPDATE(x, h, l) (((x) << (l)) & GENMASK((h), (l)))
| ^~~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:201:50: note: in expansion of macro 'UPDATE'
201 | #define RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(x) UPDATE(x, 7, 9)
| ^~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:1046:26: note: in expansion of macro 'RK3328_TERM_RESISTOR_CALIB_SPEED_7_0'
1046 | inno_write(inno, 0xc6, RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(v));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
As pointed out by Robin and Guenter, inno_write's val argument is an
8-bit value so having a mask larger than that doesn't make sense. This
also matches the rest of the *_7_0 macros in this driver.
[1]: https://lore.kernel.org/lkml/20190801230358.4193-2-rikard.falkeborn@gmail.com/
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Despite extensive testing of commit 885bd76596 ("phy: qcom-qmp: Correct
READY_STATUS poll break condition") I failed to conclude that the
PHYSTATUS bit of the PCS_STATUS register used in PCIe and USB3 falls as
the PHY gets ready. Similar to the prior bug with UFS the code will
generally get past the check before the transition and thereby
"succeed".
Correct the name of the register used PCIe and USB3 PHYs, replace
mask_pcs_ready with a constant expression depending on the type of the
PHY and check for the appropriate ready state.
Cc: stable@vger.kernel.org
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Fixes: 885bd76596 ("phy: qcom-qmp: Correct READY_STATUS poll break condition")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence create a new label,
err_node_put, that puts the previous node (child) before returning the
required value. Also include the statement pm_runtime_disable() under
this label in order to avoid repetition among mid-loop return
conditions. Edit the mid-loop return statements to instead go to this
new label err_node_put.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The hardware manual should be revised, but the initial value of
VBCTRL.OCCLREN is set to 1 actually. If the bit is set, the hardware
clears VBCTRL.VBOUT and ADPCTRL.DRVVBUS registers automatically
when the hardware detects over-current signal from a USB power switch.
However, since the hardware doesn't have any registers which
indicates over-current, the driver cannot handle it at all. So, if
"is_otg_channel" hardware detects over-current, since ADPCTRL.DRVVBUS
register is cleared automatically, the channel cannot be used after
that.
To resolve this behavior, this patch sets the VBCTRL.OCCLREN to 0
to keep ADPCTRL.DRVVBUS even if the "is_otg_channel" hardware
detects over-current. (We assume a USB power switch itself protects
over-current and turns the VBUS off.)
This patch is inspired by a BSP patch from Kazuya Mizuguchi.
Fixes: 1114e2d317 ("phy: rcar-gen3-usb2: change the mode to OTG on the combined channel")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The regmap_node variable is still being used in the syscon_node_to_regmap()
call after the of_node_put() call, which may result in use-after-free.
Fixes: 71e2f5c5c2 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PHY configuration has been implemented in the firmware and accessed
through SMC calls. In the past, it worked magically if the bootloader
was correctly doing the initializations.
With up-to-date bindings, the kernel will need a recent firmware in
order to do the initializations himself (we assume people must update
their firmware along with their kernel).
People might not understand why IPs that were working correctly before
stopped to be probed suddendly. In this case, let's advise the users
to update their firmware with a visual warning.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Samsung PHY drivers control the power to the SoC core components needed by
their client devices (USB HCDs, SATA, camera ISP bridge, DP encoder) to
properly operate. Disabling PHYs in runtime usually causes the client
device to crash with external abort exception or similar issue due to lack
of API to notify clients about PHY removal. This patch removes the
possiblity to unbind Samsung Exynos PHY drivers in runtime.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 36914111e6 ("drivers: phy: add calibrate method") added support
for generic phy_calibrate() method, but it didn't explain in detail when
such method is supposed to be called. Add some more documentation directly
to the phy.h to make it clean that it is intended to be called after every
host controller reset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Unconditionally include the lantiq subdirectory in the phy Makefile.
All drivers in there have their dependencies maintained. One of these
(optional) dependencies is COMPILE_TEST, however this can only be
evaluated when Kconfig scans the lantiq subdirectory.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Lantiq VRX200 SoCs embed a PCIe PHY in the "sram" bus. Unlike most
other IP blocks on this SoC the register values are only 16-bit wide.
Like other IP blocks on this SoC the register values are in big endian.
The PHY embeds a PLL which can be configured in various modes. Only the
36MHz mode is supported for now, the other modes can be implemented when
there's a board which actually needs them. OpenWrt uses the out-of-tree
vendor driver and all supported boards there only need the 36MHz mode.
There are two input clocks:
- the "pdi" clock enables the register access
- the "phy" clock is the clock input and enables the internal PLL
There are two reset lines:
- "phy" resets the PHY itself
- the "pcie" reset line is shared between the PHY and the PCIe
controller
While the VRX200 SoC has only one PCIe controller and PHY the ARX300
uses two identical PCIe controllers and PHYs which are compatible with
the PCIe controller and PHY on VRX200.
Add a driver for this PHY so PCIe support can be enabled on these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A future patch is going to change semantics of clk_register() so that
clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid
referencing this member here so that we don't run into NULL pointer
exceptions.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190731193517.237136-9-sboyd@kernel.org
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Synopsys DesignWare core based PCIe controllers in Tegra 194 SoC
interface with Universal PHY (UPHY) module through a PIPE2UPHY (P2U)
module. For each PCIe lane of a controller, there is a P2U unit
instantiated at hardware level. This driver provides support for the
programming required for each P2U that is going to be used for a PCIe
controller.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Thierry Reding <treding@nvidia.com>
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=5mPE
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
phy: for 5.3
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay
phy: meson-g12a-usb3-pcie: disable locking for cr_regmap
phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs
dt-bindings: phy: Add documentation for mixel dphy
dt-bindings: phy-pxa-usb: add bindings
phy: renesas: rcar-gen3-usb2: fix imbalance powered flag
phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting
phy: qcom-qmp: Correct READY_STATUS poll break condition
phy: ti: am654-serdes: Make serdes_am654_xlate() static
phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings
phy: samsung: Use struct_size() in devm_kzalloc()
phy: qcom: Add Qualcomm PCIe2 PHY driver
dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
*) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124
*) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210
*) Minor fixes: fix memory leaks at error path and addresses coverity.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=+dGx
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.2-rc
*) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124
*) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210
*) Minor fixes: fix memory leaks at error path and addresses coverity.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: tegra: xusb: Add Tegra210 PLL power supplies
phy: tegra: xusb: Add Tegra124 PLL power supplies
dt-bindings: phy: tegra-xusb: List PLL power supplies
phy: usb: phy-brcm-usb: Remove sysfs attributes upon driver removal
phy: renesas: rcar-gen2: Fix memory leak at error paths
phy: qcom-qusb2: fix missing assignment of ret when calling clk_prepare_enable
readl_poll_timeout() calls usleep_range() to sleep between reads.
usleep_range() doesn't work efficiently for tiny values.
Raise the polling delay in qcom_qmp_phy_enable() to bring it in line
with the delay in qcom_qmp_phy_com_init().
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Locking is not needed for the phy_g12a_usb3_pcie_cr_bus_read/write() and
currently it causes the following BUG because of the usage of the
regmap_read_poll_timeout() running in spinlock_irq, configured by regmap fast_io.
Simply disable locking in the cr_regmap config since it's only used from the
PHY init callback function.
BUG: sleeping function called from invalid context at drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c:85
in_atomic(): 1, irqs_disabled(): 128, pid: 60, name: kworker/3:1
[snip]
Workqueue: events deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x190
show_stack+0x14/0x20
dump_stack+0x90/0xb4
___might_sleep+0xec/0x110
__might_sleep+0x50/0x88
phy_g12a_usb3_pcie_cr_bus_addr.isra.0+0x80/0x1a8
phy_g12a_usb3_pcie_cr_bus_read+0x34/0x1d8
_regmap_read+0x60/0xe0
_regmap_update_bits+0xc4/0x110
regmap_update_bits_base+0x60/0x90
phy_g12a_usb3_pcie_init+0xdc/0x210
phy_init+0x74/0xd0
dwc3_meson_g12a_probe+0x2cc/0x4d0
platform_drv_probe+0x50/0xa0
really_probe+0x20c/0x3b8
driver_probe_device+0x68/0x150
__device_attach_driver+0xa8/0x170
bus_for_each_drv+0x64/0xc8
__device_attach+0xd8/0x158
device_initial_probe+0x10/0x18
bus_probe_device+0x90/0x98
deferred_probe_work_func+0x94/0xe8
process_one_work+0x1e0/0x338
worker_thread+0x230/0x458
kthread+0x134/0x138
ret_from_fork+0x10/0x1c
Fixes: 36077e16c0 ("phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the Mixel DPHY as found on i.MX8 CPUs but since
this is an IP core it will likely be found on others in the future. So
instead of adding this to the nwl host driver make it a generic PHY
driver.
The driver supports the i.MX8MQ. Support for i.MX8QM and i.MX8QXP can be
added once the necessary system controller bits are in via
mixel_dphy_devdata.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Co-developed-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
'mask_com_pcs_ready' is only useful if 'has_phy_com_ctrl' is true.
Since msm8998_pciephy_cfg.has_phy_com_ctrl is false, let's drop
msm8998_pciephy_cfg.mask_com_pcs_ready altogether.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
After issuing a PHY_START request to the QMP, the hardware documentation
states that the software should wait for the PCS_READY_STATUS to become
1.
With the introduction of commit c9b589791f ("phy: qcom: Utilize UFS
reset controller") an additional 1ms delay was introduced between the
start request and the check of the status bit. This greatly increases
the chances for the hardware to actually becoming ready before the
status bit is read.
The result can be seen in that UFS PHY enabling is now reported as a
failure in 10% of the boots on SDM845, which is a clear regression from
the previous rare/occasional failure.
This patch fixes the "break condition" of the poll to check for the
correct state of the status bit.
Unfortunately PCIe on 8996 and 8998 does not specify the mask_pcs_ready
register, which means that the code checks a bit that's always 0. So the
patch also fixes these, in order to not regress these targets.
Fixes: 73d7ec899b ("phy: qcom-qmp: Add msm8998 PCIe QMP PHY support")
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Cc: stable@vger.kernel.org
Cc: Evan Green <evgreen@chromium.org>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix sparse warning:
drivers/phy/ti/phy-am654-serdes.c:250:12: warning:
symbol 'serdes_am654_xlate' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct samsung_usb2_phy_driver {
...
struct samsung_usb2_phy_instance instances[0];
};
instance = devm_kzalloc(dev, sizeof(struct samsung_usb2_phy_driver) +
count * sizeof(struct samsung_usb2_phy_instance),
GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, instances, count),
GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 53 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.904365654@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra210 SoC has four inputs that consume power in order to supply
the PLLs that drive the various USB, PCI and SATA pads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Tegra124 SoC has four inputs that consume power in order to supply
the PLLs that drive the various USB, PCI and SATA pads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We are not destroying the sysfs attribute groupe we registered during
the probe function which will make subsequent probe calls to that
driver fail. Correct that with adding a remove function which only
removes those attributes since the reference counting on clocks did its
job already.
Fixes: 415060b21f ("phy: usb: phy-brcm-usb: Add ability to force DRD mode to host or device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch fixes memory leak at error paths of the probe function.
In for_each_child_of_node, if the loop returns, the driver should
call of_put_node() before returns.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Fixes: 1233f59f74 ("phy: Renesas R-Car Gen2 PHY driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 30 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error return from the call to clk_prepare_enable is not being assigned
to variable ret even though ret is being used to check if the call failed.
Fix this by adding in the missing assignment.
Addresses-Coverity: ("Logically dead code")
Fixes: 891a96f65a ("phy: qcom-qusb2: Add support for runtime PM")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Prior to the adoption of SPDX, it was difficult for tools to determine
the correct license due to incomplete or badly formatted license text.
The SPDX solves this issue, assuming people can correctly spell
"SPDX-License-Identifier" although this assumption is broken in some
places.
Since scripts/spdxcheck.py parses only lines that exactly matches to
the correct tag, it cannot (should not) detect this kind of error.
If the correct tag is missing, scripts/checkpatch.pl warns like this:
WARNING: Missing or malformed SPDX-License-Identifier tag in line *
So, people should notice it before the patch submission, but in reality
broken tags sometimes slip in. The checkpatch warning is not useful for
checking the committed files globally since large number of files still
have no SPDX tag.
Also, I am not sure about the legal effect when the SPDX tag is broken.
Anyway, these typos are absolutely worth fixing. It is pretty easy to
find suspicious lines by grep.
$ git grep --not -e SPDX-License-Identifier --and -e SPDX- -- \
:^LICENSES :^scripts/spdxcheck.py :^*/license-rules.rst
arch/arm/kernel/bugs.c:// SPDX-Identifier: GPL-2.0
drivers/phy/st/phy-stm32-usbphyc.c:// SPDX-Licence-Identifier: GPL-2.0
drivers/pinctrl/sh-pfc/pfc-r8a77980.c:// SPDX-Lincense-Identifier: GPL 2.0
lib/test_stackinit.c:// SPDX-Licenses: GPLv2
sound/soc/codecs/max9759.c:// SPDX-Licence-Identifier: GPL-2.0
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm PCIe2 PHY is based on design from Synopsys and found in
several different platforms where the QMP PHY isn't used.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 24 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.162703968@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
