usb_disconnect() no longer acquires usb_bus_list_lock, so update its
comment to that effect.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set SEL control urbs cannot be sent to a device in unconfigured state.
This patch adds a check in usb_req_set_sel() to ensure the usb device's
state is USB_STATE_CONFIGURED.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
In the bos usb_ss_cap_descriptor structure, bU2DevExitLat is of type __le16.
This value is used as it is, without being first converted to the CPU
byteorder, for the setup of usb device's usb3_lpm_parameters.
This patch fixes that by converting bU2DevExitLat field to the CPU byteorder
before the assignmenment to [udev/hub]_u2_del variables.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets the lpm_capable field for root hubs with LPM capabilities.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the incorrect assignment of a variable with type 'le16'
to a variable with type 'unsigned int'.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usb_reset_and_verify_device(), hub_port_init() allocates a new bos
descriptor to hold the value read by the device. The new bos descriptor
has to be compared with the old one in order to figure out if device 's
firmware has changed in which case the device has to be reenumerated.
In the original code, none of the two descriptors was deallocated leading
to memory leaks.
This patch compares the old bos descriptor with the new one to detect change
in firmware and releases the newly allocated bos descriptor to prevent memory
leak.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Tested-by: Martin MOKREJS <mmokrejs@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After successful initialization hub->descriptor->bNbrPorts and
hub->hdev->maxchild are equal, but using hub->hdev->maxchild is
preferred because that value is explicitly used for initialization
of hub->ports[].
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ignoring usb_hub_create_port_device() errors cause later NULL pointer
deference when uninitialized hub->ports[i] entries are dereferenced
after port memory allocation error.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the hub_configure() fails after setting the hdev->maxchild
the hub->ports might be NULL or point to uninitialized kzallocated
memory causing NULL pointer dereference in hub_quiesce() during cleanup.
Now after such error the hdev->maxchild is set to 0 to avoid cleanup
of uninitialized ports.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
This is the first of three steps to fix your usb-linus and usb-next
trees. As I mentioned, commit 4fae6f0fa8
"USB: handle LPM errors during device suspend correctly" was incorrectly
added to usb-next when it should have been added to usb-linus and marked
for stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step one, and contains the backported version of
commit 4fae6f0fa8, the two port power off
fixes, and an unrelated xhci-plat bug fix.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0/wL
-----END PGP SIGNATURE-----
Merge tag 'for-usb-2013-08-15-step-1' into for-usb-next
xhci: Step 1 to fix usb-linus and usb-next.
Hi Greg,
This is the first of three steps to fix your usb-linus and usb-next
trees. As I mentioned, commit 4fae6f0fa8
"USB: handle LPM errors during device suspend correctly" was incorrectly
added to usb-next when it should have been added to usb-linus and marked
for stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step one, and contains the backported version of
commit 4fae6f0fa8, the two port power off
fixes, and an unrelated xhci-plat bug fix.
Sarah Sharp
Resolved conflicts:
drivers/usb/core/hub.c
The pm qos NO_POWER_OFF flag is checked twice during usb device suspend
to see if the usb port power off condition is met. This is redundant and
also will prevent the port from being powered off if the NO_POWER_OFF
flag is changed to 1 from 0 after the device was already suspended.
More detail in the following link.
http://marc.info/?l=linux-usb&m=136543949130865&w=2
This patch should be backported to kernels as old as 3.7, that
contain the commit f7ac7787ad "usb/acpi:
Use ACPI methods to power off ports."
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The hub driver's usb_port_suspend() routine doesn't handle errors
related to Link Power Management properly. It always returns failure,
it doesn't try to clean up the wakeup setting, (in the case of system
sleep) it doesn't try to go ahead with the port suspend regardless,
and it doesn't try to apply the new power-off mechanism.
This patch fixes these problems.
Note: Sarah fixed this patch to apply against 3.11, since the original
commit (4fae6f0fa8 "USB: handle LPM errors
during device suspend correctly") called usb_disable_remote_wakeup,
which won't be added until 3.12.
This patch should be backported to kernels as old as 3.5, that
contain the commit 8306095fd2 "USB:
Disable USB 3.0 LPM in critical sections.". There will be merge
conflicts, since LTM wasn't added until 3.6.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When building the htmldocs (in verbose mode), scripts/kernel-doc reports the
following type of warnings:
Warning(drivers/usb/core/usb.c:76): No description found for return value of
'usb_find_alt_setting'
Fix them by:
- adding some missing descriptions of return values
- using "Return" sections for those descriptions
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub driver's usb_port_suspend() routine doesn't handle errors
related to Link Power Management properly. It always returns failure,
it doesn't try to clean up the wakeup setting, (in the case of system
sleep) it doesn't try to go ahead with the port suspend regardless,
and it doesn't try to apply the new power-off mechanism.
This patch fixes these problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub driver is inconsistent in its organization of code for
enabling and disabling remote wakeup. There is a special routine to
disable wakeup for SuperSpeed devices but not for slower devices, and
there is no special routine to enable wakeup.
This patch refactors the code. It renames and changes the existing
function to make it handle both SuperSpeed and non-SuperSpeed devices,
and it adds a corresponding routine to enable remote wakeup. It also
changes the speed determination to look at the device's speed rather
than the speed of the parent hub -- this shouldn't make any difference
because a SuperSpeed device always has to be attached to a SuperSpeed
hub and conversely.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies the interface presented by usb_get_status().
Instead of forcing callers to check for the proper data length and
convert the status value to host byte order, the function will now
do these things itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.
However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.
This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.
However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.
This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch removes a redundant nested "#ifdef CONFIG_PM" from the hub
driver. It also adds a label to the "#endif" line corresponding to
the outer "#ifdef CONFIG_PM".
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: William Gulland <wgulland@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub driver was recently changed to use "global" suspend for system
suspend transitions on non-SuperSpeed buses. This means that we don't
suspend devices individually by setting the suspend feature on the
upstream hub port; instead devices all go into suspend automatically
when the root hub stops transmitting packets. The idea was to save
time and to avoid certain kinds of wakeup races.
Now it turns out that many hubs are buggy; they don't relay wakeup
requests from a downstream port to their upstream port if the
downstream port's suspend feature is not set (depending on the speed
of the downstream port, whether or not the hub is enabled for remote
wakeup, and possibly other factors).
We can't have hubs dropping wakeup requests. Therefore this patch
goes partway back to the old policy: It sets the suspend feature for a
port if the device attached to that port or any of its descendants is
enabled for wakeup. People will still be able to benefit from the
time savings if they don't care about wakeup and leave it disabled on
all their devices.
In order to accomplish this, the patch adds a new field to the usb_hub
structure: wakeup_enabled_descendants is a count of how many devices
below a suspended hub are enabled for remote wakeup. A corresponding
new subroutine determines the number of wakeup-enabled devices at or
below an arbitrary suspended USB device.
This should be applied to the 3.10 stable kernel.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hub_to_struct_hub() can return NULL in some unlikely cases.
Add checks where appropriate, or pass the hub pointer as an additional
argument if it's known to be valid.
The places it makes sense to check usb_hub_to_struct_hub()
are picked based on feedback from Alan Stern.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM). The net result is code
shrinkage and simplification.
There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it. The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1674) speeds up system sleep transitions by not
suspending each individual device on a USB-1.1 or USB-2 bus. The
devices will automatically go into suspend when their root hubs are
suspended (i.e., stop sending out Start-Of-Frame packets) -- this is
what the USB spec calls "global suspend".
Since this is what we do already when CONFIG_USB_SUSPEND isn't
enabled, it shouldn't cause any problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1673) reduces the amount of log spew from the hub driver
by removing a bunch of error messages in the case where the device in
question is already known to have been disconnected. Since the
disconnect event itself appears in the log, there's no need for other
error messages.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jenya Y <jy.gerstmaier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return an error if hub->descriptor->bNbrPorts==0. Without this additional
check, we can end up doing a "hub->ports = kzalloc(0, GFP_KERNEL)".
This hub->ports pointer will therefore be non-NULL and will be used.
Example of dmesg:
INIT: usb 1-1: New USB device found, idVendor=0424, idProduct=2512
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1:1.0: USB hub found
version 2.86 bootinghub 1-1:1.0: 0 ports detected
Unable to handle kernel NULL pointer dereference at virtual address 00000010
Signed-off-by: David Linares <dlinares.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If one storage interface or usb network interface(iSCSI case) exists in
current configuration, memory allocation with GFP_KERNEL during
usb_device_reset() might trigger I/O transfer on the storage interface
itself and cause deadlock because the 'us->dev_mutex' is held in
.pre_reset() and the storage interface can't do I/O transfer when the
reset is triggered by other interface, or the error handling can't be
completed if the reset is triggered by the storage itself (error
handling path).
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This pulls in a bunch of fixes that are in Linus's tree because we need them
here for testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to add usb port auto power off mechanism.
When usb device is suspending, usb core will suspend usb port and
usb port runtime pm callback will clear PORT_POWER feature to
power off port if all conditions were met. These conditions are
remote wakeup disable, pm qos NO_POWER_OFF flag clear and persist
enable. When it resumes, power on port again.
Add did_runtime_put in the struct usb_port to ensure
pm_runtime_get/put(portdev) to be called pairedly. Set did_runtime_put
to true when call pm_runtime_put(portdev) during suspending. The
pm_runtime_get(portdev) only will be called when did_runtime_put
is set to true during resuming. Set did_runtime_put to false after
calling pm_runtime_get(portdev).
Make clear_port_feature() and hdev_to_hub() as global symbol.
Rename clear_port_feature() to usb_clear_port_feature() and
hdev_to_hub() to usb_hub_to_struct_hub().
Extend hub_port_debounce() with the fuction of debouncing to
be connected. Add two wraps: hub_port_debounce_be_connected()
and hub_port_debouce_be_stable().
Increase HUB_DEBOUNCE_TIMEOUT to 2000 because some usb ssds
needs around 1.5 or more to make the hub port status to be
connected steadily after being powered off and powered on.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to add runtime pm callback for usb port device.
Set/clear PORT_POWER feature in the resume/suspend callback.
Add portnum for struct usb_port to record port number. Do
pm_rumtime_get_sync/put(portdev) when a device is plugged/unplugged
to prevent it from being powered off when it is active.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usb3.0 device defines function remote wakeup which is only for interface
recipient rather than device recipient. This is different with usb2.0 device's
remote wakeup feature which is defined for device recipient. According usb3.0
spec 9.4.5, the function remote wakeup can be modified by the SetFeature()
requests using the FUNCTION_SUSPEND feature selector. This patch is to use
correct way to disable usb3.0 device's function remote wakeup after suspend
error and resuming.
This should be backported to kernels as old as 3.4, that contain the
commit 623bef9e03 "USB/xhci: Enable remote
wakeup for USB3 devices."
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
ACPI provide "_PLD" and "_UPC" aml methods to describe usb port
visibility and connectability. This patch is to add usb_hub_adjust_DeviceRemovable()
to adjust usb hub port's DeviceRemovable according ACPI information and invoke it in
the rh_call_control(). When hub descriptor request is issued at first time,
usb port device isn't created and usb port is not bound with acpi. So first
hub descriptor request is not changed based on ACPI information. After usb
port devices being created, call usb_hub_adjust_DeviceRemovable in the hub_configure()
and then set hub port's DeviceRemovable according ACPI information and this also works
for non-root hub.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To show the relationship between usb port and child device,
add link file "port" under usb device's sysfs directoy and
"device" under usb port device's sysfs directory. They are linked
to each other.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to create driver/usb/core/(port.c,hub.h) files and move usb
port related code into port.c.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah pointed out that the USB3.0 spec also updates the amount of power
that may be consumed by the device and quoted 9.2.5.1:
|"The amount of current draw for SuperSpeed devices are increased to 150
|mA for low-power devices and 900 mA for high-power"
This patch tries to update all users to use the larger values for
SuperSpeed devices and use the "old" ones for everything else.
While here, two other changes suggested by Alan:
- the comment referering to 7.2.1.1 has been updated to 7.2.1 which is
the correct source of the action.
- the check for hubs with zero ports has been removed.
- compute bus power by full_load * num_ports on root hubs
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB 2.0 specification says that bMaxPower is the maximum power
consumption expressed in 2 mA units and the USB 3.0 specification says
that it is expressed in 8 mA units.
This patch adds a helper function usb_get_max_power() which computes the
value based on config & usb_device's speed value. The the device descriptor
dump computes the value on its own.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor hub_port_wait_reset into a small loop to wait for the port
reset to be complete, and then a larger block to deal with the final
port status. This patch should not change any current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Change the code that manually issues a Set Port Feature(Link State) to
use the new helper function hub_set_port_link_state().
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
A USB 3.0 device can transition to the Inactive state if a U1 or U2 exit
transition fails. The current code in hub_events simply issues a warm
reset, but does not call any pre-reset or post-reset driver methods (or
unbind/rebind drivers without them). Therefore the drivers won't know
their device has just been reset.
hub_events should instead call usb_reset_device. This means
hub_port_reset now needs to figure out whether it should issue a warm
reset or a hot reset.
Remove the FIXME note about needing disconnect() for a NOTATTACHED
device. This patch fixes that.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
When a hot reset fails on a USB 3.0 port, the current port reset code
recursively calls hub_port_reset inside hub_port_wait_reset. This isn't
ideal, since we should avoid recursive calls in the kernel, and it also
doesn't allow us to issue multiple warm resets on reset failures.
Rip out the recursive call. Instead, add code to hub_port_reset to
issue a warm reset if the hot reset fails, and try multiple warm resets
before giving up on the port.
In hub_port_wait_reset, remove the recursive call and re-indent. The
code is basically the same, except:
1. It bails out early if the port has transitioned to Inactive or
Compliance Mode after the reset completed.
2. It doesn't consider a connect status change to be a failed reset. If
multiple warm resets needed to be issued, the connect status may have
changed, so we need to ignore that and look at the port link state
instead. hub_port_reset will now do that.
3. It unconditionally sets udev->speed on all types of successful
resets. The old recursive code would set the port speed when the second
hub_port_reset returned.
The old code did not handle connected devices needing a warm reset well.
There were only two situations that the old code handled correctly: an
empty port needing a warm reset, and a hot reset that migrated to a warm
reset.
When an empty port needed a warm reset, hub_port_reset was called with
the warm variable set. The code in hub_port_finish_reset would skip
telling the USB core and the xHC host that the device was reset, because
otherwise that would result in a NULL pointer dereference.
When a USB 3.0 device reset migrated to a warm reset, the recursive call
made the call stack look like this:
hub_port_reset(warm = false)
hub_wait_port_reset(warm = false)
hub_port_reset(warm = true)
hub_wait_port_reset(warm = true)
hub_port_finish_reset(warm = true)
(return up the call stack to the first wait)
hub_port_finish_reset(warm = false)
The old code didn't want to notify the USB core or the xHC host of device reset
twice, so it only did it in the second call to hub_port_finish_reset,
when warm was set to false. This was necessary because
before patch two ("USB: Ignore xHCI Reset Device status."), the USB core
would pay attention to the xHC Reset Device command error status, and
the second call would always fail.
Now that we no longer have the recursive call, and warm can change from
false to true in hub_port_reset, we need to have hub_port_finish_reset
unconditionally notify the USB core and the xHC of the device reset.
In hub_port_finish_reset, unconditionally clear the connect status
change (CSC) bit for USB 3.0 hubs when the port reset is done. If we
had to issue multiple warm resets for a device, that bit may have been
set if the device went into SS.Inactive and then was successfully warm
reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The next patch will refactor the hub port code to rip out the recursive
call to hub_port_reset on a failed hot reset. In preparation for that,
make sure all code paths can deal with being called with a NULL udev.
The usb_device will not be valid if warm reset was issued because a port
transitioned to the Inactive or Compliance Mode on a device connect.
This patch should have no effect on current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The EHCI host controller needs to prevent EHCI initialization when the
UHCI or OHCI companion controller is in the middle of a port reset. It
uses ehci_cf_port_reset_rwsem to do this. USB 3.0 hubs can't be under
an EHCI host controller, so it makes no sense to down the semaphore for
USB 3.0 hubs. It also makes the warm port reset code more complex.
Don't down ehci_cf_port_reset_rwsem for USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train. In that case, we
issue a warm reset. Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.
The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded. This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.
Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes. Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.
Make hub_events disable the port if warm reset fails. This will disable
the port, and then bring it back into the RxDetect state. Make the USB
core ignore the connect change until the device reconnects.
Note that this patch does NOT handle connected devices slipping into the
Inactive state very well. This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure. However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.
This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab "usbcore: refine warm
reset logic"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
The port reset code bails out early if the current connect status is
cleared (device disconnected). If we're issuing a hot reset, it may
also look at the link state before the reset is finished.
Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the
Error state or Resetting state, the port connection bit retains the
value from the previous state. Therefore we can't trust it until the
reset finishes. Also, the xHCI spec section 4.19.1.2.5 says software
shall ignore the link state while the port is resetting, as it can be in
an unknown state.
The port state during reset is also unknown for USB 2.0 hubs. The hub
sends a reset signal by driving the bus into an SE0 state. This
overwhelms the "connect" signal from the device, so the port can't tell
whether anything is connected or not.
Fix the port reset code to ignore the port link state and current
connect bit until the reset finishes, and USB_PORT_STAT_RESET is
cleared.
Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case,
because it's redundant. When the warm reset finishes, the port reset
bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set.
Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit
in the code to deal with the finished reset.
This patch should be backported to all stable kernels.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete. The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port. Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects. To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.
The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes. We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect. However,
external USB 3.0 hubs don't need this code. They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set. Therefore it doesn't make sense to
put this code in the USB core.
This patch is part of a series to fix several reports of infinite loops
on device enumeration failure. This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller. The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.
This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab "usbcore: refine warm
reset logic"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
