The GPIO controller found on Tegra186 and later supports debouncing for
inputs for up to 255 ms.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The controls for the GG port on Tegra194 resides in the power partition
of the C5 PCIe controller and its interrupt route mapping can therefore
not be programmed by early boot firmware along with that of the other
ports.
Detect this generically by looking at which controls have already been
locked down using the security registers and fill in default values for
controls that are unlocked.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The register offsets for a given bank and port can be easily derived
from the bank and port indices. Update the port descriptors to list only
the bank and port numbers to simplify this.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
It's hard for occasional GPIO code reader/writer to know if values 0/1
equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT to help them out.
NOTE - for gpio-amd-fch and gpio-bd9571mwv:
This commit also changes the return value for direction get to equal 1
for direction INPUT. Prior this commit these drivers might have
returned some other positive value but 1 for INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO controller doesn't have any controls to enable the system to
wake up from low power states based on activity on GPIO pins. An extra
hardware block that is part of the power management controller (PMC)
contains these controls. In order for the GPIO controller to be able
to cooperate with the PMC, obtain a reference to the PMC's IRQ domain
and make it a parent to the GPIO controller's IRQ domain. This way the
PMC gets an opportunity to program the additional registers required
to enable wakeup sources on suspend.
Based on additional work by Bitan Biswas <bbiswas@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191002144502.156393-2-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 6 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.720704315@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new prefix allows the GPIOs to be uniquely identified on a per-chip
basis, which makes it easier to distinguish Tegra186 specific GPIOs from
those of later chips such as Tegra194 which supports a very different
set of GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The IRQ core code refers to the interrupt type by that name, whereas the
term flow is almost never used. Some GPIO controllers use the term
flow_type, but it is most consistent to just go with the IRQ core
terminology.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Tegra194 GPIO bank configuration.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is no longer required after commit 959bc7b22b
("gpio: Automatically add lockdep keys")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra186 has two GPIO controllers that are largely register compatible
between one another but are completely different from the controller
found on earlier generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
