Update ipv4_confirm_neigh to handle an ipv6 gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bpf_ipv4_fib_lookup to handle an ipv6 gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common theme in the output path is looking up a neigh entry for a
nexthop, either the gateway in an rtable or a fallback to the daddr
in the skb:
nexthop = (__force u32)rt_nexthop(rt, ip_hdr(skb)->daddr);
neigh = __ipv4_neigh_lookup_noref(dev, nexthop);
if (unlikely(!neigh))
neigh = __neigh_create(&arp_tbl, &nexthop, dev, false);
To allow the nexthop to be an IPv6 address we need to consider the
family of the nexthop and then call __ipv{4,6}_neigh_lookup_noref based
on it.
To make this simpler, add a ip_neigh_gw4 helper similar to ip_neigh_gw6
added in an earlier patch which handles:
neigh = __ipv4_neigh_lookup_noref(dev, nexthop);
if (unlikely(!neigh))
neigh = __neigh_create(&arp_tbl, &nexthop, dev, false);
And then add a second one, ip_neigh_for_gw, that calls either
ip_neigh_gw4 or ip_neigh_gw6 based on the address family of the gateway.
Update the output paths in the VRF driver and core v4 code to use
ip_neigh_for_gw simplifying the family based lookup and making both
ready for a v6 nexthop.
ipv4_neigh_lookup has a different need - the potential to resolve a
passed in address in addition to any gateway in the rtable or skb. Since
this is a one-off, add ip_neigh_gw4 and ip_neigh_gw6 diectly. The
difference between __neigh_create used by the helpers and neigh_create
called by ipv4_neigh_lookup is taking a refcount, so add rcu_read_lock_bh
and bump the refcnt on the neigh entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch allows an IPv6 gateway with an IPv4 route. The neighbor
entry will exist in the v6 ndisc table and the cached header will contain
the ipv6 protocol which is wrong for an IPv4 packet. For an IPv4 packet to
use the v6 neighbor entry, neigh_output needs to skip the cached header
and just use the output callback for the neigh entry.
A future patchset can look at expanding the hh_cache to handle 2
protocols. For now, IPv6 gateways with an IPv4 route will take the
extra overhead of generating the header.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to use fib6_nh_init to validate a nexthop spec with an IPv6
gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_check_nh is currently huge covering multiple uses cases - device only,
device + gateway, and device + gateway with ONLINK. The next patch adds
validation checks for IPv6 which only further complicates it. So, break
fib_check_nh into 2 helpers - one for gateway validation and one for device
only.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an IPv6 gateway to fib_config. Since a gateway is either
IPv4 or IPv6, make it a union with fc_gw4 where fc_gw_family decides
which address is in use. Update current checks on family and gw4 to
handle ipv6 as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an IPv6 gateway to rtable. Since a gateway is either
IPv4 or IPv6, make it a union with rt_gw4 where rt_gw_family decides
which address is in use.
When dumping the route data, encode an ipv6 nexthop using RTA_VIA.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to rtable, fib_config needs to allow the gateway to be either an
IPv4 or an IPv6 address. To that end, rename fc_gw to fc_gw4 to mean an
IPv4 address and add fc_gw_family. Checks on 'is a gateway set' are changed
to see if fc_gw_family is set. In the process prepare the code for a
fc_gw_family == AF_INET6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow the gateway to be either an IPv4 or IPv6 address, remove
rt_uses_gateway from rtable and replace with rt_gw_family. If
rt_gw_family is set it implies rt_uses_gateway. Rename rt_gateway
to rt_gw4 to represent the IPv4 version.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the gateway in a fib_nh_common to be from a different address
family than the outer fib{6}_nh. To that end, replace nhc_has_gw with
nhc_gw_family and update users of nhc_has_gw to check nhc_gw_family.
Now nhc_family is used to know if the nh_common is part of a fib_nh
or fib6_nh (used for container_of to get to route family specific data),
and nhc_gw_family represents the address family for the gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv6 helpers to handle ndisc references via the stub. Update
bpf_ipv6_fib_lookup to use __ipv6_neigh_lookup_noref_stub instead of
the open code ___neigh_lookup_noref with the stub.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib6_nh_init and fib6_nh_release to ipv6_stubs. If fib6_nh_init fails,
callers should not invoke fib6_nh_release, so there is no reason to have
a dummy stub for the IPv6 is not enabled case.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit a297569fe0 ("net/udp: do not touch skb->peeked unless
really needed") the 'peeked' argument of __skb_try_recv_datagram()
and friends is always equal to !!'flags & MSG_PEEK'.
Since such argument is really a boolean info, and the callers have
already 'flags & MSG_PEEK' handy, we can remove it and clean-up the
code a bit.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John reports:
Recent refactoring of fl_change aims to use the classifier spinlock to
avoid the need for rtnl lock. In doing so, the fl_hw_replace_filer()
function was moved to before the lock is taken. This can create problems
for drivers if duplicate filters are created (commmon in ovs tc offload
due to filters being triggered by user-space matches).
Drivers registered for such filters will now receive multiple copies of
the same rule, each with a different cookie value. This means that the
drivers would need to do a full match field lookup to determine
duplicates, repeating work that will happen in flower __fl_lookup().
Currently, drivers do not expect to receive duplicate filters.
To fix this, verify that filter with same key is not present in flower
classifier hash table and insert the new filter to the flower hash table
before offloading it to hardware. Implement helper function
fl_ht_insert_unique() to atomically verify/insert a filter.
This change makes filter visible to fast path at the beginning of
fl_change() function, which means it can no longer be freed directly in
case of error. Refactor fl_change() error handling code to deallocate the
filter with rcu timeout.
Fixes: 620da48608 ("net: sched: flower: refactor fl_change")
Reported-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes rhashtables to use a bit_spin_lock on BIT(1) of the
bucket pointer to lock the hash chain for that bucket.
The benefits of a bit spin_lock are:
- no need to allocate a separate array of locks.
- no need to have a configuration option to guide the
choice of the size of this array
- locking cost is often a single test-and-set in a cache line
that will have to be loaded anyway. When inserting at, or removing
from, the head of the chain, the unlock is free - writing the new
address in the bucket head implicitly clears the lock bit.
For __rhashtable_insert_fast() we ensure this always happens
when adding a new key.
- even when lockings costs 2 updates (lock and unlock), they are
in a cacheline that needs to be read anyway.
The cost of using a bit spin_lock is a little bit of code complexity,
which I think is quite manageable.
Bit spin_locks are sometimes inappropriate because they are not fair -
if multiple CPUs repeatedly contend of the same lock, one CPU can
easily be starved. This is not a credible situation with rhashtable.
Multiple CPUs may want to repeatedly add or remove objects, but they
will typically do so at different buckets, so they will attempt to
acquire different locks.
As we have more bit-locks than we previously had spinlocks (by at
least a factor of two) we can expect slightly less contention to
go with the slightly better cache behavior and reduced memory
consumption.
To enhance type checking, a new struct is introduced to represent the
pointer plus lock-bit
that is stored in the bucket-table. This is "struct rhash_lock_head"
and is empty. A pointer to this needs to be cast to either an
unsigned lock, or a "struct rhash_head *" to be useful.
Variables of this type are most often called "bkt".
Previously "pprev" would sometimes point to a bucket, and sometimes a
->next pointer in an rhash_head. As these are now different types,
pprev is NULL when it would have pointed to the bucket. In that case,
'blk' is used, together with correct locking protocol.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HSR should forget nodes after configured node forget time expiry based
on HSR_NODE_FORGET_TIME. As part of hsr_prune_nodes(), code checks to
see if entries are to be flushed out if not heard for longer than forget
time. But currently hsr_prune_nodes() is called only once during device
creation. Restart the timer at the end of hsr_prune_nodes() so that
hsr_prune_nodes() gets called periodically and forgotten entries are
removed from node table.
Signed-off-by: Aaron Kramer <a-kramer@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a debugfs interface to allow display the nodes learned
by the hsr master.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a blank line after function declaration as suggested by
checkpatch.pl -f
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver code uses camel case in many places. This is
seen when ran checkpatch.pl -f on files under net/hsr. This
patch fixes the code to remove camel case usage.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add missing space around operator in code. This is
seen when ran checkpatch.pl -f on files under net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a multi-line statement exceeding 80 characters, logical operator
should be at the end of a line instead of being at the start. This
is seen when ran checkpatch.pl -f on files under net/hsr. The change
is per suggestion from checkpatch.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary space after a cast. This is seen
when ran checkpatch.pl -f on files under net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all instance of NULL checks such as
if (foo == NULL) with if (!foo)
Also
if (foo != NULL) with if (foo)
This is seen when ran checkpatch.pl -f on files under net/hsr
and suggestion is to replace as above.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes function calls that ends with '(' in a line.
This is seen when ran checkpatch.pl -f option on files under
net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes alignment issues in code for functions. This is
seen when ran checkpatch.pl -f option on files under net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes unnecessary paranthesis from the code. This is
seen when ran checkpatch.pl -f option on files under net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes multiple blank lines in the code. This is seen
when ran checkpatch.pl -f option for files under net/hsr
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes lines exceeding 80 characters. This is seen
when ran checkpatch.pl with -f option for files under
net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The non-null check on tskb is always false because it is in an else
path of a check on tskb and hence tskb is null in this code block.
This is check is therefore redundant and can be removed as well
as the label coalesc.
if (tsbk) {
...
} else {
...
if (unlikely(!skb)) {
if (tskb) /* can never be true, redundant code */
goto coalesc;
return;
}
}
Addresses-Coverity: ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to commit 674d9de02a ("NFC: Fix possible memory
corruption when handling SHDLC I-Frame commands").
I'm not totally sure, but I think that commit description may have
overstated the danger. I was under the impression that this data came
from the firmware? If you can't trust your networking firmware, then
you're already in trouble.
Anyway, these days we add bounds checking where ever we can and we call
it kernel hardening. Better safe than sorry.
Fixes: 11f54f2286 ("NFC: nci: Add HCI over NCI protocol support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several hash table refcount fixes in batman-adv, from Sven
Eckelmann.
2) Use after free in bpf_evict_inode(), from Daniel Borkmann.
3) Fix mdio bus registration in ixgbe, from Ivan Vecera.
4) Unbounded loop in __skb_try_recv_datagram(), from Paolo Abeni.
5) ila rhashtable corruption fix from Herbert Xu.
6) Don't allow upper-devices to be added to vrf devices, from Sabrina
Dubroca.
7) Add qmi_wwan device ID for Olicard 600, from Bjørn Mork.
8) Don't leave skb->next poisoned in __netif_receive_skb_list_ptype,
from Alexander Lobakin.
9) Missing IDR checks in mlx5 driver, from Aditya Pakki.
10) Fix false connection termination in ktls, from Jakub Kicinski.
11) Work around some ASPM issues with r8169 by disabling rx interrupt
coalescing on certain chips. From Heiner Kallweit.
12) Properly use per-cpu qstat values on NOLOCK qdiscs, from Paolo
Abeni.
13) Fully initialize sockaddr_in structures in SCTP, from Xin Long.
14) Various BPF flow dissector fixes from Stanislav Fomichev.
15) Divide by zero in act_sample, from Davide Caratti.
16) Fix bridging multicast regression introduced by rhashtable
conversion, from Nikolay Aleksandrov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
ibmvnic: Fix completion structure initialization
ipv6: sit: reset ip header pointer in ipip6_rcv
net: bridge: always clear mcast matching struct on reports and leaves
libcxgb: fix incorrect ppmax calculation
vlan: conditional inclusion of FCoE hooks to match netdevice.h and bnx2x
sch_cake: Make sure we can write the IP header before changing DSCP bits
sch_cake: Use tc_skb_protocol() helper for getting packet protocol
tcp: Ensure DCTCP reacts to losses
net/sched: act_sample: fix divide by zero in the traffic path
net: thunderx: fix NULL pointer dereference in nicvf_open/nicvf_stop
net: hns: Fix sparse: some warnings in HNS drivers
net: hns: Fix WARNING when remove HNS driver with SMMU enabled
net: hns: fix ICMP6 neighbor solicitation messages discard problem
net: hns: Fix probabilistic memory overwrite when HNS driver initialized
net: hns: Use NAPI_POLL_WEIGHT for hns driver
net: hns: fix KASAN: use-after-free in hns_nic_net_xmit_hw()
flow_dissector: rst'ify documentation
ipv6: Fix dangling pointer when ipv6 fragment
net-gro: Fix GRO flush when receiving a GSO packet.
flow_dissector: document BPF flow dissector environment
...
In commit 0ae955e2656d ("tipc: improve TIPC throughput by Gap ACK
blocks"), we enhance the link transmq by releasing as many packets as
possible with the multi-ACKs from peer node. This also means the queue
is now non-linear and the peer link deferdq becomes vital.
Whereas, in the case of link failover, all messages in the link transmq
need to be transmitted as tunnel messages in such a way that message
sequentiality and cardinality per sender is preserved. This requires us
to maintain the link deferdq somehow, so that when the tunnel messages
arrive, the inner user messages along with the ones in the deferdq will
be delivered to upper layer correctly.
The commit accomplishes this by defining a new queue in the TIPC link
structure to hold the old link deferdq when link failover happens and
process it upon receipt of tunnel messages.
Also, in the case of link syncing, the link deferdq will not be purged
to avoid unnecessary retransmissions that in the worst case will fail
because the packets might have been freed on the sending side.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For unicast transmission, the current NACK sending althorithm is over-
active that forces the sending side to retransmit a packet that is not
really lost but just arrived at the receiving side with some delay, or
even retransmit same packets that have already been retransmitted
before. As a result, many duplicates are observed also under normal
condition, ie. without packet loss.
One example case is: node1 transmits 1 2 3 4 10 5 6 7 8 9, when node2
receives packet #10, it puts into the deferdq. When the packet #5 comes
it sends NACK with gap [6 - 9]. However, shortly after that, when
packet #6 arrives, it pulls out packet #10 from the deferfq, but it is
still out of order, so it makes another NACK with gap [7 - 9] and so on
... Finally, node1 has to retransmit the packets 5 6 7 8 9 a number of
times, but in fact all the packets are not lost at all, so duplicates!
This commit reduces duplicates by changing the condition to send NACK,
also restricting the retransmissions on individual packets via a timer
of about 1ms. However, it also needs to say that too tricky condition
for NACKs or too long timeout value for retransmissions will result in
performance reducing! The criterias in this commit are found to be
effective for both the requirements to reduce duplicates but not affect
performance.
The tipc_link_rcv() is also improved to only dequeue skb from the link
deferdq if it is expected (ie. its seqno <= rcv_nxt).
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
During unicast link transmission, it's observed very often that because
of one or a few lost/dis-ordered packets, the sending side will fastly
reach the send window limit and must wait for the packets to be arrived
at the receiving side or in the worst case, a retransmission must be
done first. The sending side cannot release a lot of subsequent packets
in its transmq even though all of them might have already been received
by the receiving side.
That is, one or two packets dis-ordered/lost and dozens of packets have
to wait, this obviously reduces the overall throughput!
This commit introduces an algorithm to overcome this by using "Gap ACK
blocks". Basically, a Gap ACK block will consist of <ack, gap> numbers
that describes the link deferdq where packets have been got by the
receiving side but with gaps, for example:
link deferdq: [1 2 3 4 10 11 13 14 15 20]
--> Gap ACK blocks: <4, 5>, <11, 1>, <15, 4>, <20, 0>
The Gap ACK blocks will be sent to the sending side along with the
traditional ACK or NACK message. Immediately when receiving the message
the sending side will now not only release from its transmq the packets
ack-ed by the ACK but also by the Gap ACK blocks! So, more packets can
be enqueued and transmitted.
In addition, the sending side can now do "multi-retransmissions"
according to the Gaps reported in the Gap ACK blocks.
The new algorithm as verified helps greatly improve the TIPC throughput
especially under packet loss condition.
So far, a maximum of 32 blocks is quite enough without any "Too few Gap
ACK blocks" reports with a 5.0% packet loss rate, however this number
can be increased in the furture if needed.
Also, the patch is backward compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mcast conversion to rhashtable this function has been unused, so
remove it.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be careful and always zero the whole br_ip struct when it is
used for matching since the rhashtable change. This patch fixes all the
places which didn't properly clear it which in turn might've caused
mismatches.
Thanks for the great bug report with reproducing steps and bisection.
Steps to reproduce (from the bug report):
ip link add br0 type bridge mcast_querier 1
ip link set br0 up
ip link add v2 type veth peer name v3
ip link set v2 master br0
ip link set v2 up
ip link set v3 up
ip addr add 3.0.0.2/24 dev v3
ip netns add test
ip link add v1 type veth peer name v1 netns test
ip link set v1 master br0
ip link set v1 up
ip -n test link set v1 up
ip -n test addr add 3.0.0.1/24 dev v1
# Multicast receiver
ip netns exec test socat
UDP4-RECVFROM:5588,ip-add-membership=224.224.224.224:3.0.0.1,fork -
# Multicast sender
echo hello | nc -u -s 3.0.0.2 224.224.224.224 5588
Reported-by: liam.mcbirnie@boeing.com
Fixes: 19e3a9c90c ("net: bridge: convert multicast to generic rhashtable")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux currently disable ECN for incoming connections when the SYN
requests ECN and the IP header has ECT(0)/ECT(1) set, as some
networks were reportedly mangling the ToS byte, hence could later
trigger false congestion notifications.
RFC8311 §4.3 relaxes RFC3168's requirements such that ECT can be set
one TCP control packets (including SYNs). The main benefit of this
is the decreased probability of losing a SYN in a congested
ECN-capable network (i.e., it avoids the initial 1s timeout).
Additionally, this allows the development of newer TCP extensions,
such as AccECN.
This patch relaxes the previous check, by enabling ECN on incoming
connections using SYN+ECT if at least one bit of the reserved flags
of the TCP header is set. Such bit would indicate that the sender of
the SYN is using a newer TCP feature than what the host implements,
such as AccECN, and is thus implementing RFC8311. This enables
end-hosts not supporting such extensions to still negociate ECN, and
to have some of the benefits of using ECN on control packets.
Signed-off-by: Olivier Tilmans <olivier.tilmans@nokia-bell-labs.com>
Suggested-by: Bob Briscoe <research@bobbriscoe.net>
Cc: Koen De Schepper <koen.de_schepper@nokia-bell-labs.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if the driver registers devlink port instance, he should set
the devlink port attributes as well. Then the devlink core is able to
obtain switch id itself, no need for driver to implement the ndo.
Once all drivers will implement devlink port registration, this ndo
should be removed. This warning guides new drivers to do things as
they should be done.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the switch ID down the to devlink through devlink_port_attrs_set()
so it can be used by devlink_compat_switch_id_get(). Leave
ndo_get_port_parent_id implementation only for legacy.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce devlink_compat_switch_id_get() helper which fills up switch_id
according to passed netdev pointer. Call it directly from
dev_get_port_parent_id() as a fallback when ndo_get_port_parent_id
is not defined for given netdev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend devlink_port_attrs_set() to pass switch ID for ports which are
part of switch and store it in port attrs. For other ports, this is
NULL.
Note that this allows the driver to group devlink ports into one or more
switches according to the actual topology.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can optimize the fdb convergence when a backup_port is present by not
immediately flushing the entries of the stopped port since traffic for
those entries will flow towards the backup_port.
There are 2 cases specifically that benefit most:
- when the stopped port comes up before the entries expire by themselves
- when there's an external entry refresh and they're kept while the
backup_port is operating (e.g. mlag)
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb somehow dequeued out of inputq before processing, it causes to
NULL pointer and kernel crashed.
Add checking skb valid before using.
Fixes: c55c8edafa ("tipc: smooth change between replicast and broadcast")
Reported-by: Tuong Lien Tong <tuong.t.lien@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to TC flower remove the requirement for rtnl lock when
accessing and modifying filters. Refcounts now ensure access and deletion
do not happen concurrently. However, the reoffload function which cycles
through all filters and replays them to registered hw drivers is not
protected.
Use the fl_get_next_filter() function to cycle the filters for reoffload
and ensure the ref taken by this function is put when done with each
filter.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Way back in 3c9c36bced the
ndo_fcoe_get_wwn pointer was switched from depending on CONFIG_FCOE to
CONFIG_LIBFCOE in order to allow building FCoE support into the bnx2x
driver and used by bnx2fc without including the generic software fcoe
module.
But, FCoE is generally used over an 802.1q VLAN, and the implementation
of ndo_fcoe_get_wwn in the 8021q module was not similarly changed. The
result is that if CONFIG_FCOE is disabled, then bnz2fc cannot make a
call to ndo_fcoe_get_wwn through the 8021q interface to the underlying
bnx2x interface. The bnx2fc driver then falls back to a potentially
different mapping of Ethernet MAC to Fibre Channel WWN, creating an
incompatibility with the fabric and target configurations when compared
to the WWNs used by pre-boot firmware and differently-configured
kernels.
So make the conditional inclusion of FCoE code in 8021q match the
conditional inclusion in netdevice.h
Signed-off-by: Chris Leech <cleech@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-04-04
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Batch of fixes to the existing BPF flow dissector API to support
calling BPF programs from the eth_get_headlen context (support for
latter is planned to be added in bpf-next), from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not actually any guarantee that the IP headers are valid before we
access the DSCP bits of the packets. Fix this using the same approach taken
in sch_dsmark.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't be using skb->protocol directly as that will miss cases with
hardware-accelerated VLAN tags. Use the helper instead to get the right
protocol number.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC8257 §3.5 explicitly states that "A DCTCP sender MUST react to
loss episodes in the same way as conventional TCP".
Currently, Linux DCTCP performs no cwnd reduction when losses
are encountered. Optionally, the dctcp_clamp_alpha_on_loss resets
alpha to its maximal value if a RTO happens. This behavior
is sub-optimal for at least two reasons: i) it ignores losses
triggering fast retransmissions; and ii) it causes unnecessary large
cwnd reduction in the future if the loss was isolated as it resets
the historical term of DCTCP's alpha EWMA to its maximal value (i.e.,
denoting a total congestion). The second reason has an especially
noticeable effect when using DCTCP in high BDP environments, where
alpha normally stays at low values.
This patch replace the clamping of alpha by setting ssthresh to
half of cwnd for both fast retransmissions and RTOs, at most once
per RTT. Consequently, the dctcp_clamp_alpha_on_loss module parameter
has been removed.
The table below shows experimental results where we measured the
drop probability of a PIE AQM (not applying ECN marks) at a
bottleneck in the presence of a single TCP flow with either the
alpha-clamping option enabled or the cwnd halving proposed by this
patch. Results using reno or cubic are given for comparison.
| Link | RTT | Drop
TCP CC | speed | base+AQM | probability
==================|=========|==========|============
CUBIC | 40Mbps | 7+20ms | 0.21%
RENO | | | 0.19%
DCTCP-CLAMP-ALPHA | | | 25.80%
DCTCP-HALVE-CWND | | | 0.22%
------------------|---------|----------|------------
CUBIC | 100Mbps | 7+20ms | 0.03%
RENO | | | 0.02%
DCTCP-CLAMP-ALPHA | | | 23.30%
DCTCP-HALVE-CWND | | | 0.04%
------------------|---------|----------|------------
CUBIC | 800Mbps | 1+1ms | 0.04%
RENO | | | 0.05%
DCTCP-CLAMP-ALPHA | | | 18.70%
DCTCP-HALVE-CWND | | | 0.06%
We see that, without halving its cwnd for all source of losses,
DCTCP drives the AQM to large drop probabilities in order to keep
the queue length under control (i.e., it repeatedly faces RTOs).
Instead, if DCTCP reacts to all source of losses, it can then be
controlled by the AQM using similar drop levels than cubic or reno.
Signed-off-by: Koen De Schepper <koen.de_schepper@nokia-bell-labs.com>
Signed-off-by: Olivier Tilmans <olivier.tilmans@nokia-bell-labs.com>
Cc: Bob Briscoe <research@bobbriscoe.net>
Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <borkmann@iogearbox.net>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify this code by updating bridge multicast stats from
maybe_deliver().
Note that commit 6db6f0eae6 ("bridge: multicast to unicast"), in case
the port flag BR_MULTICAST_TO_UNICAST is set, never updates the previous
port pointer, therefore it is always going to be different from the
existing port in this deduplicated list iteration.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like 46cfd725c3 ("net: use kfree_skb_list() helper in more places").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export fib_nexthop_info and fib_add_nexthop for use by IPv6 code.
Remove rt6_nexthop_info and rt6_add_nexthop in favor of the IPv4
versions. Update fib_nexthop_info for IPv6 linkdown check and
RTA_GATEWAY for AF_INET6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the exception of the nexthop weight, the nexthop attributes used by
fib_nexthop_info and fib_add_nexthop come from the fib_nh_common struct.
Update both to use it and change fib_nexthop_info to check the family
as needed.
nexthop weight comes from the common struct for existing use cases, but
for nexthop groups the weight is outside of the fib_nh_common to allow
the same nexthop definition to be used in multiple groups with different
weights.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to ipv6, move addition of nexthop attributes to dump
message into helpers that are called for both single path and
multipath routes. Align the new helpers to the IPv6 variant
which most notably means computing the flags argument based on
settings in nh_flags.
The RTA_FLOW argument is unique to IPv4, so it is appended after
the new fib_nexthop_info helper. The intent of a later patch is to
make both fib_nexthop_info and fib_add_nexthop usable for both IPv4
and IPv6. This patch is stepping stone in that direction.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the ipv4 code only needs data from fib_nh_common. Add
fib_nh_common selection to fib_result and update users to use it.
Right now, fib_nh_common in fib_result will point to a fib_nh struct
that is embedded within a fib_info:
fib_info --> fib_nh
fib_nh
...
fib_nh
^
fib_result->nhc ----+
Later, nhc can point to a fib_nh within a nexthop struct:
fib_info --> nexthop --> fib_nh
^
fib_result->nhc ---------------+
or for a nexthop group:
fib_info --> nexthop --> nexthop --> fib_nh
nexthop --> fib_nh
...
nexthop --> fib_nh
^
fib_result->nhc ---------------------------+
In all cases nhsel within fib_result will point to which leg in the
multipath route is used.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update fib_table_lookup tracepoint to take a fib_nh_common struct and
dump the v6 gateway address if the nexthop uses it.
Over the years saddr has not proven useful and the output of the
tracepoint produces very long lines. Since saddr is not part of
fib_nh_common, drop it. If it needs to be added later, fib_nh which
contains saddr can be obtained from a fib_nh_common via container_of.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the beginning of ip6_fragment func, the prevhdr pointer is
obtained in the ip6_find_1stfragopt func.
However, all the pointers pointing into skb header may change
when calling skb_checksum_help func with
skb->ip_summed = CHECKSUM_PARTIAL condition.
The prevhdr pointe will be dangling if it is not reloaded after
calling __skb_linearize func in skb_checksum_help func.
Here, I add a variable, nexthdr_offset, to evaluate the offset,
which does not changes even after calling __skb_linearize func.
Fixes: 405c92f7a5 ("ipv6: add defensive check for CHECKSUM_PARTIAL skbs in ip_fragment")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com>
Reported-by: syzbot+e8ce541d095e486074fc@syzkaller.appspotmail.com
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we may merge incorrectly a received GSO packet
or a packet with frag_list into a packet sitting in the
gro_hash list. skb_segment() may crash case because
the assumptions on the skb layout are not met.
The correct behaviour would be to flush the packet in the
gro_hash list and send the received GSO packet directly
afterwards. Commit d61d072e87 ("net-gro: avoid reorders")
sets NAPI_GRO_CB(skb)->flush in this case, but this is not
checked before merging. This patch makes sure to check this
flag and to not merge in that case.
Fixes: d61d072e87 ("net-gro: avoid reorders")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
net/rxrpc/local_object.c: In function ‘rxrpc_open_socket’:
net/rxrpc/local_object.c:175:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret < 0) {
^
net/rxrpc/local_object.c:184:2: note: here
case AF_INET:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Currently, GCC is expecting to find the fall-through annotations
at the very bottom of the case and on its own line. That's why
I had to add the annotation, although the intentional fall-through
is already mentioned in a few lines above.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use whitelist instead of a blacklist and allow only a small set of
fields that might be relevant in the context of flow dissector:
* data
* data_end
* flow_keys
This is required for the eth_get_headlen case where we have only a
chunk of data to dissect (i.e. trying to read the other skb fields
doesn't make sense).
Note, that it is a breaking API change! However, we've provided
flow_keys->n_proto as a substitute for skb->protocol; and there is
no need to manually handle skb->vlan_present. So even if we
break somebody, the migration is trivial. Unfortunately, we can't
support eth_get_headlen use-case without those breaking changes.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Don't allow BPF program to set flow_keys->nhoff to less than initial
value. We currently don't read the value afterwards in anything but
the tests, but it's still a good practice to return consistent
values to the test programs.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is a preparation for the next commit that would prohibit access to
the most fields of __sk_buff from the BPF programs.
Instead of requiring BPF flow dissector programs to look into skb,
pass all input data in the flow_keys.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Action tunnel_key doesn't have a metadata/tunnel for release(decap) action.
Drivers do not dereference entry->tunnel pointer for that action type, so
this behavior doesn't result in a crash at the moment. However, this needs
to be corrected as a preparation for updating hardware offloads API to not
rely on rtnl lock, for which flow_action code will copy the tunnel data to
temporary buffer to prevent concurrent action overwrite from
invalidating/freeing it.
Fixes: 3a7b68617d ("cls_api: add translator to flow_action representation")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device type for ip6 tunnels is set to
ARPHRD_TUNNEL6. However, the ip4ip6_err function
is expecting the device type of the tunnel to be
ARPHRD_TUNNEL. Since the device types do not
match, the function exits and the ICMP error
packet is not sent to the originating host. Note
that the device type for IPv4 tunnels is set to
ARPHRD_TUNNEL.
Fix is to expect a tunnel device type of
ARPHRD_TUNNEL6 instead. Now the tunnel device
type matches and the ICMP error packet is sent
to the originating host.
Signed-off-by: Sheena Mira-ato <sheena.mira-ato@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We free "ct_info->ct" and then use it on the next line when we pass it
to nf_ct_destroy_timeout(). This patch swaps the order to avoid the use
after free.
Fixes: 06bd2bdf19 ("openvswitch: Add timeout support to ct action")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fills a hole in softnet data, so no change in structure size.
Also prepares for xmit_more placement in the same spot;
skb->xmit_more will be removed in followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dccp_feat_push_change fails, we forget free the mem
which is alloced by kmemdup in dccp_feat_clone_sp_val.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e8ef967a54 ("dccp: Registration routines for changing feature values")
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Eric noticed, in .sk_destruct, sk->sk_dst_cache update is prevented, and
no barrier is needed for this. So change to use rcu_dereference_protected()
instead of rcu_dereference_check() to fetch sk_dst_cache in there.
v1->v2:
- no change, repost after net-next is open.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot report a kernel-infoleak:
BUG: KMSAN: kernel-infoleak in _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
Call Trace:
_copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
copy_to_user include/linux/uaccess.h:174 [inline]
sctp_getsockopt_peer_addrs net/sctp/socket.c:5911 [inline]
sctp_getsockopt+0x1668e/0x17f70 net/sctp/socket.c:7562
...
Uninit was stored to memory at:
sctp_transport_init net/sctp/transport.c:61 [inline]
sctp_transport_new+0x16d/0x9a0 net/sctp/transport.c:115
sctp_assoc_add_peer+0x532/0x1f70 net/sctp/associola.c:637
sctp_process_param net/sctp/sm_make_chunk.c:2548 [inline]
sctp_process_init+0x1a1b/0x3ed0 net/sctp/sm_make_chunk.c:2361
...
Bytes 8-15 of 16 are uninitialized
It was caused by that th _pad field (the 8-15 bytes) of a v4 addr (saved in
struct sockaddr_in) wasn't initialized, but directly copied to user memory
in sctp_getsockopt_peer_addrs().
So fix it by calling memset(addr->v4.sin_zero, 0, 8) to initialize _pad of
sockaddr_in before copying it to user memory in sctp_v4_addr_to_user(), as
sctp_v6_addr_to_user() does.
Reported-by: syzbot+86b5c7c236a22616a72f@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Tested-by: Alexander Potapenko <glider@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When kcm is loaded while many processes try to create a KCM socket, a
crash occurs:
BUG: unable to handle kernel NULL pointer dereference at 000000000000000e
IP: mutex_lock+0x27/0x40 kernel/locking/mutex.c:240
PGD 8000000016ef2067 P4D 8000000016ef2067 PUD 3d6e9067 PMD 0
Oops: 0002 [#1] SMP KASAN PTI
CPU: 0 PID: 7005 Comm: syz-executor.5 Not tainted 4.12.14-396-default #1 SLE15-SP1 (unreleased)
RIP: 0010:mutex_lock+0x27/0x40 kernel/locking/mutex.c:240
RSP: 0018:ffff88000d487a00 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 000000000000000e RCX: 1ffff100082b0719
...
CR2: 000000000000000e CR3: 000000004b1bc003 CR4: 0000000000060ef0
Call Trace:
kcm_create+0x600/0xbf0 [kcm]
__sock_create+0x324/0x750 net/socket.c:1272
...
This is due to race between sock_create and unfinished
register_pernet_device. kcm_create tries to do "net_generic(net,
kcm_net_id)". but kcm_net_id is not initialized yet.
So switch the order of the two to close the race.
This can be reproduced with mutiple processes doing socket(PF_KCM, ...)
and one process doing module removal.
Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before creating a slave netdevice, get the mac address from DTS and
apply in case it is valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code to flush qdisc tree and purge the qdisc queue
is duplicated in many places and in most cases it does not
respect NOLOCK qdisc: the global backlog len is used and the
per CPU values are ignored.
This change addresses the above, factoring-out the relevant
code and using the helpers introduced by the previous patch
to fetch the correct backlog len.
Fixes: c5ad119fb6 ("net: sched: pfifo_fast use skb_array")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Classful qdiscs can't access directly the child qdiscs backlog
length: if such qdisc is NOLOCK, per CPU values should be
accounted instead.
Most qdiscs no not respect the above. As a result, qstats fetching
for most classful qdisc is currently incorrect: if the child qdisc is
NOLOCK, it always reports 0 len backlog.
This change introduces a pair of helpers to safely fetch
both backlog and qlen and use them in stats class dumping
functions, fixing the above issue and cleaning a bit the code.
DRR needs also to access the child qdisc queue length, so it
needs custom handling.
Fixes: c5ad119fb6 ("net: sched: pfifo_fast use skb_array")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It returned always NULL, thus it was never possible to get the filter.
Example:
$ ip link add foo type dummy
$ ip link add bar type dummy
$ tc qdisc add dev foo clsact
$ tc filter add dev foo protocol all pref 1 ingress handle 1234 \
matchall action mirred ingress mirror dev bar
Before the patch:
$ tc filter get dev foo protocol all pref 1 ingress handle 1234 matchall
Error: Specified filter handle not found.
We have an error talking to the kernel
After:
$ tc filter get dev foo protocol all pref 1 ingress handle 1234 matchall
filter ingress protocol all pref 1 matchall chain 0 handle 0x4d2
not_in_hw
action order 1: mirred (Ingress Mirror to device bar) pipe
index 1 ref 1 bind 1
CC: Yotam Gigi <yotamg@mellanox.com>
CC: Jiri Pirko <jiri@mellanox.com>
Fixes: fd62d9f5c5 ("net/sched: matchall: Fix configuration race")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration check to accept source route IP options should be made on
the incoming netdevice when the skb->dev is an l3mdev master. The route
lookup for the source route next hop also needs the incoming netdev.
v2->v3:
- Simplify by passing the original netdevice down the stack (per David
Ahern).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that struct ipv6_pinfo is not located as we think.
inet6_sk_generic() and tcp_inet6_sk() disagree on 32bit kernels by 4-bytes,
because struct tcp_sock has 8-bytes alignment,
but ipv6_pinfo size is not a multiple of 8.
sizeof(struct ipv6_pinfo): 116 (not padded to 8)
I actually first coded tcp_inet6_sk() as this patch does, but thought
that "container_of(tcp_sk(sk), struct tcp6_sock, tcp)" was cleaner.
As Julian told me : Nobody should use tcp6_sock.inet6
directly, it should be accessed via tcp_inet6_sk() or inet6_sk().
This happened when we added the first u64 field in struct tcp_sock.
Fixes: 93a77c11ae ("tcp: add tcp_inet6_sk() helper")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Bisected-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tcp_sk_init() failed in inet_ctl_sock_create(),
'net->ipv4.tcp_congestion_control' will be left
uninitialized, but tcp_sk_exit() hasn't check for
that.
This patch add checking on 'net->ipv4.tcp_congestion_control'
in tcp_sk_exit() to prevent NULL-ptr dereference.
Fixes: 6670e15244 ("tcp: Namespace-ify sysctl_tcp_default_congestion_control")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot found a crash:
BUG: KMSAN: uninit-value in tipc_nl_compat_name_table_dump+0x54f/0xcd0 net/tipc/netlink_compat.c:872
Call Trace:
tipc_nl_compat_name_table_dump+0x54f/0xcd0 net/tipc/netlink_compat.c:872
__tipc_nl_compat_dumpit+0x59e/0xda0 net/tipc/netlink_compat.c:215
tipc_nl_compat_dumpit+0x63a/0x820 net/tipc/netlink_compat.c:280
tipc_nl_compat_handle net/tipc/netlink_compat.c:1226 [inline]
tipc_nl_compat_recv+0x1b5f/0x2750 net/tipc/netlink_compat.c:1265
genl_family_rcv_msg net/netlink/genetlink.c:601 [inline]
genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
genl_rcv+0x63/0x80 net/netlink/genetlink.c:637
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
Uninit was created at:
__alloc_skb+0x309/0xa20 net/core/skbuff.c:208
alloc_skb include/linux/skbuff.h:1012 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1182 [inline]
netlink_sendmsg+0xb82/0x1300 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
It was supposed to be fixed on commit 974cb0e3e7 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") by checking TLV_GET_DATA_LEN(msg->req)
in cmd->header()/tipc_nl_compat_name_table_dump_header(), which is called
ahead of tipc_nl_compat_name_table_dump().
However, tipc_nl_compat_dumpit() doesn't handle the error returned from cmd
header function. It means even when the check added in that fix fails, it
won't stop calling tipc_nl_compat_name_table_dump(), and the issue will be
triggered again.
So this patch is to add the process for the err returned from cmd header
function in tipc_nl_compat_dumpit().
Reported-by: syzbot+3ce8520484b0d4e260a5@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar issue as fixed by Patch "tipc: check bearer name with right
length in tipc_nl_compat_bearer_enable" was also found by syzbot in
tipc_nl_compat_link_set().
The length to check with should be 'TLV_GET_DATA_LEN(msg->req) -
offsetof(struct tipc_link_config, name)'.
Reported-by: syzbot+de00a87b8644a582ae79@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported the following crash:
BUG: KMSAN: uninit-value in memchr+0xce/0x110 lib/string.c:961
memchr+0xce/0x110 lib/string.c:961
string_is_valid net/tipc/netlink_compat.c:176 [inline]
tipc_nl_compat_bearer_enable+0x2c4/0x910 net/tipc/netlink_compat.c:401
__tipc_nl_compat_doit net/tipc/netlink_compat.c:321 [inline]
tipc_nl_compat_doit+0x3aa/0xaf0 net/tipc/netlink_compat.c:354
tipc_nl_compat_handle net/tipc/netlink_compat.c:1162 [inline]
tipc_nl_compat_recv+0x1ae7/0x2750 net/tipc/netlink_compat.c:1265
genl_family_rcv_msg net/netlink/genetlink.c:601 [inline]
genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
genl_rcv+0x63/0x80 net/netlink/genetlink.c:637
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
Uninit was created at:
__alloc_skb+0x309/0xa20 net/core/skbuff.c:208
alloc_skb include/linux/skbuff.h:1012 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1182 [inline]
netlink_sendmsg+0xb82/0x1300 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
It was triggered when the bearer name size < TIPC_MAX_BEARER_NAME,
it would check with a wrong len/TLV_GET_DATA_LEN(msg->req), which
also includes priority and disc_domain length.
This patch is to fix it by checking it with a right length:
'TLV_GET_DATA_LEN(msg->req) - offsetof(struct tipc_bearer_config, name)'.
Reported-by: syzbot+8b707430713eb46e1e45@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a small use-after-free fix.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAlyeRsgTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi8i6B/9wP90ZLGzdAZDIlfWKXjGB1PUrFdeN
WCA5p68Hl7yh1RbY6cvbZcTF5Bo3DhjxjxTFjXHPXLxsARlxbCXon9R6Lo2lDgA4
Bk/W8dcR3onU3nspifG91Him/WnImWB80pyVgZog2PTiwsZJ0rRknXXbRU9ARCpk
8vjg19O4wHwXgtMXAN3vxjQ7v8T8wk8vDb08efPcmMPLDYMaTUL1z2JoqyRfMTbo
OpZoXSjHXqVFfz0mJ5EN7+92eK39oDcQIDSuuqePDCI09ZmrcQd/xSvG5tBfPoXr
1mR3ojkKRURW5RKGClbSoAt90vIuYJH5Cncmemzsr6m4FETH6XthGbJl
=twzl
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.1-rc3' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A patch to avoid choking on multipage bvecs in the messenger and a
small use-after-free fix"
* tag 'ceph-for-5.1-rc3' of git://github.com/ceph/ceph-client:
ceph: fix use-after-free on symlink traversal
libceph: fix breakage caused by multipage bvecs
Replace the br_port_exists() macro with its twin from netdevice.h
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NULL or ZERO_SIZE_PTR will be returned for zero sized memory
request, and derefencing them will lead to a segfault
so it is unnecessory to call vzalloc for zero sized memory
request and not call functions which maybe derefence the
NULL allocated memory
this also fixes a possible memory leak if phy_ethtool_get_stats
returns error, memory should be freed before exit
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Wang Li <wangli39@baidu.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only decrypt_internal() performs zero copy on rx, all paths
which don't hit decrypt_internal() must set zc to false,
otherwise tls_sw_recvmsg() may return 0 causing the application
to believe that that connection got closed.
Currently this happens with device offload when new record
is first read from.
Fixes: d069b780e3 ("tls: Fix tls_device receive")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently no support for the multicast/broadcast aspects
of VXLAN in ovs. In the datapath flow the tun_dst must specific.
But in the IP_TUNNEL_INFO_BRIDGE mode the tun_dst can not be specific.
And the packet can forward through the fdb table of vxlan devcice. In
this mode the broadcast/multicast packet can be sent through the
following ways in ovs.
ovs-vsctl add-port br0 vxlan -- set in vxlan type=vxlan \
options:key=1000 options:remote_ip=flow
ovs-ofctl add-flow br0 in_port=LOCAL,dl_dst=ff:ff:ff:ff:ff:ff, \
action=output:vxlan
bridge fdb append ff:ff:ff:ff:ff:ff dev vxlan_sys_4789 dst 172.168.0.1 \
src_vni 1000 vni 1000 self
bridge fdb append ff:ff:ff:ff:ff:ff dev vxlan_sys_4789 dst 172.168.0.2 \
src_vni 1000 vni 1000 self
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP stack relies on the fact that a freshly allocated skb
has skb->cb[] and skb_shinfo(skb)->tx_flags cleared.
When recycling tx skb, we must ensure these fields are cleared.
Fixes: 472c2e07ee ("tcp: add one skb cache for tx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.
Code move only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With fib_nh_common in place, move common initialization and release
code into helpers used by both ipv4 and ipv6. For the moment, the init
is just the lwt encap and the release is both the netdev reference and
the the lwt state reference. More will be added later.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib_nh_common struct with common nexthop attributes. Convert
fib_nh and fib6_nh to use it. Use macros to move existing
fib_nh_* references to the new nh_common.nhc_*.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename fib6_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, gateway, flags, and lwtstate are common
with all nexthop definitions. In some places new temporary variables
are declared or local variables renamed to maintain line lengths.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename fib_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, oif, gateway, flags, scope, lwtstate,
nh_weight and nh_upper_bound are common with all nexthop definitions.
In the process shorten fib_nh_lwtstate to fib_nh_lws to avoid really
long lines.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_add_nexthop and rt6_nexthop_info only need the fib6_info for the
gateway flag and the nexthop weight, and the presence of a gateway is now
per-nexthop. Update the signatures to take a fib6_nh and nexthop weight
and better align with the ipv4 versions.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_ignore_linkdown takes a fib6_info but only looks at the net_device
and its IPv6 config. Change it to take a net_device over a fib6_info as
its input argument.
In addition, move it to a header file to make the check inline and usable
later with IPv4 code without going through the ipv6 stub, and rename to
ip6_ignore_linkdown since it is only checking the setting based on the
ipv6 struct on a device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
