Although gpiod_get_direction() can be considered side-effect free for
consumers, its internals involve setting or clearing bits in the
affected GPIO descriptor, for which we need to force-cast the const
descriptor variable to non-const. This could lead to incorrect behavior
if the compiler decides to optimize here, so remove this const
attribute. The intent is to make gpiod_get_direction() private anyway,
so it does not really matter.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the ARCH_NR_GPIOS-sized static array of GPIO descriptors by
dynamically-allocated arrays for each GPIO chip.
This change makes gpio_to_desc() perform in O(n) (where n is the number
of GPIO chips registered) instead of O(1), however since n is rarely
bigger than 1 or 2 no noticeable performance issue is expected.
Besides this provides more incentive for GPIO consumers to move to the
gpiod interface. One could use a O(log(n)) structure to link the GPIO
chips together, but considering the low limit of n the hypothetical
performance benefit is probably not worth the added complexity.
This patch uses kcalloc() in gpiochip_add(), which removes the ability
to add a chip before kcalloc() can operate. I am not aware of such
cases, but if someone bisects up to this patch then I will be proven
wrong...
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It doesn't make much sense to make some (possible expensive) calls to
gpio_is_valid() first, and to ignore the result if the base number is
negative. Check for a positive base number first.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
To unify how we connect cascaded IRQ chips to parent IRQs, if
NULL us passed as handler to the gpiochip_set_chained_irqchip()
function, assume the chips is nested rather than chained, and
we still get the parent set up correctly by way of this function
call.
Alter the drivers for tc3589x and stmpe to use this to set up
their chained handlers as a demonstration of the usage.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the IRQ from the parent is nested the IRQ may need to be
resent under certain conditions. Currently the chained IRQ
handler in gpiolib does not handle connecting nested IRQs
but it is conceptually correct to indicate the actual parent
IRQ.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no guarantee that VIRQs will be allocated sequentially
for gpio irqchip in gpiochip_irqchip_add().
Therefore, it's unsafe to dispose VIRQ in gpiochip_irqchip_remove()
basing on index relatively to stored irq_base value.
Hence, use irq_find_mapping for VIRQ finding in gpiochip_irqchip_remove()
instead of irq_base + index.
Reported-by: Wang, Yalin <Yalin.Wang@sonymobile.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is possibility with misconfigured pins that interrupt occurs instantly
after setting irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Now if handler gets called before irq_set_handler_data() the handler gets
NULL handler data.
Fix this by moving irq_set_handler_data() call before
irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Cc: Stable <stable@vger.kernel.org> # 3.15+
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
GPIO direction flags are not getting set because
an 'if' statement is the wrong way around.
Cc: Stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current prototype of gpiochip_request_own_desc() requires to obtain
a pointer to a descriptor. This is in contradiction to all other GPIO
request schemes, and imposes an extra step of obtaining a descriptor to
drivers. Most drivers actually cannot even perform that step since the
function that does it (gpichip_get_desc()) is gpiolib-private.
Change gpiochip_request_own_desc() to return a descriptor from a
(chip, hwnum) tuple and update users of this function (currently
gpiolib-acpi only).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The huge majority of GPIOs have their direction and initial value set
right after being obtained by one of the gpiod_get() functions. The
integer GPIO API had gpio_request_one() that took a convenience flags
parameter allowing to specify an direction and value applied to the
returned GPIO. This feature greatly simplifies client code and ensures
errors are always handled properly.
A similar feature has been requested for the gpiod API. Since setting
the direction of a GPIO is so often the very next action done after
obtaining its descriptor, we prefer to extend the existing functions
instead of introducing new functions that would raise the
number of gpiod getters to 16 (!).
The drawback of this approach is that all gpiod clients need to be
updated. To limit the pain, temporary macros are introduced that allow
gpiod_get*() to be called with or without the extra flags argument. They
will be removed once all consumer code has been updated.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since now we have irqchip helpers that the GPIO chip drivers are supposed
to use if possible, we can move the registration of ACPI events to happen
in these helpers. This seems to be more natural place and might encourage
GPIO chip driver writers to take advantage of the irqchip helpers.
We make the functions available to GPIO chip drivers via private gpiolib.h,
just in case generic irqchip helpers are not suitable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per example from the regulator subsystem: put all defines and
functions related to registering board info for GPIO descriptors
into a separate <linux/gpio/machine.h> header.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both functions were introduced to let gpio drivers request their own
gpio pins. Without exporting the functions, this can however only be
used by gpio drivers built into the kernel.
Secondary impact is that the functions can not currently be used by
platform initialization code associated with the gpio-pca953x driver.
This code permits auto-export of gpio pins through platform data, but
if this functionality is used, the module can no longer be unloaded due
to the problem solved with the introduction of gpiochip_request_own_desc
and gpiochip_free_own_desc.
Export both function so they can be used from modules and from
platform initialization code.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_ensure_requested() only makes sense when using the integer-based
GPIO API, so make sure it is called from there instead of the gpiod
API which we know cannot be called with a non-requested GPIO anyway.
The uses of gpio_ensure_requested() in the gpiod API were kind of
out-of-place anyway, so putting them in gpio-legacy.c helps clearing the
code.
Actually, considering the time this ensure_requested mechanism has been
around, maybe we should just turn this patch into "remove
gpio_ensure_requested()" if we know for sure that no user depend on it
anymore?
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_lock/unlock_as_irq() are working with (chip, offset) arguments and
are thus not using the old integer namespace. Therefore, there is no
reason to have gpiod variants of these functions working with
descriptors, especially since the (chip, offset) tuple is more suitable
to the users of these functions (GPIO drivers, whereas GPIO descriptors
are targeted at GPIO consumers).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As GPIO descriptors are not going to remain unique anymore, having this
function public is not safe. Restrain its use to gpiolib since we have
no user outside of it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old integer GPIO interface is, in effect, a privileged user of the
gpiod interface. Reflect this fact further by moving legacy GPIO support
into its own source file. This makes the code clearer and will allow us
to disable legacy GPIO support in the (far) future.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sysfs support is currently entangled within the core GPIO support, while
it should relly just be a (privileged) user of the integer GPIO API.
This patch is a first step towards making the gpiolib code more readable
by splitting it into logical parts.
Move all sysfs support to their own source file, and share static
members of gpiolib that need to be in the private gpiolib.h file. In
the future we will want to put some of them back into gpiolib.c, but this
first patch let us at least identify them.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Compiling out GPIO labels results in a space gain so small that it can
hardly be justified. Labels can also be useful for printing debug
messages, so always keep them around.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit dd34c37aa3 (gpio: of: Allow -gpio suffix for property names)
added parsing for both -gpio and -gpios suffix but also changed
the handling for deferred probe unintentionally. Because of the
looping the second name will now return -ENOENT instead of
-EPROBE_DEFER. Fix the issue by breaking out of the loop if
-EPROBE_DEFER is encountered.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce gpiod_get_optional() and gpiod_get_index_optional() helpers
that make it easier for drivers to handle optional GPIOs.
Currently in order to handle optional GPIOs, a driver needs to special
case error handling for -ENOENT, such as this:
gpio = gpiod_get(dev, "foo");
if (IS_ERR(gpio)) {
if (PTR_ERR(gpio) != -ENOENT)
return PTR_ERR(gpio);
gpio = NULL;
}
if (gpio) {
/* set up GPIO */
}
With these new helpers the above is reduced to:
gpio = gpiod_get_optional(dev, "foo");
if (IS_ERR(gpio))
return PTR_ERR(gpio);
if (gpio) {
/* set up GPIO */
}
While at it, device-managed variants of these functions are also
provided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function is called gpiod_get(), not gpio_get(). Fix the kernel-doc
comment to match the name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many bindings use the -gpio suffix in property names. Support this in
addition to the -gpios suffix when requesting GPIOs using the new
descriptor-based API.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_find_gpio() is always called under an IS_ENABLED(CONFIG_OF), so the
dummy implementation provided for !OF configurations is not needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO irqchip drivers exploit the irqdomain mapping
function to set up the IRQ default type in the hardware,
make sure that if we pass IRQ_TYPE_NONE, no hardware setup
whatsoever takes place (this should be the norm) until
later when the IRQ gets utilized.
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: linux-omap <linux-omap@vger.kernel.org>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Another feature that is duplicated in a number of GPIO irqchips
is that these cascades IRQs are assigned their own lock class
so as to avoid warnings about lockdep recursions. Do this also
in the generic GPIO irqchip helpers for smooth transition to
this core infrastructure.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some off-chip GPIO expanders need to be communicated by I2C or
SPI traffic, but may still support IRQs. By the sleeping nature
of such buses, such IRQ handlers need to be threaded. Support
such handlers in the gpiochip irqchip helpers by flagging IRQs
as threaded if the .can_sleep property of the gpiochip is
true.
Helpfully deny registration of chained IRQ handlers if the
.can_sleep property is set, as such chips will invariably need
a nested handler rather than a chained handler.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During irq mapping, in irq_set_chip_and_handler() the process
of setting this up may incur calls to lock the irqchip, which
in turn may need to dereference and use the chip data. So set
the data first, then set the chip and handler.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using the irqchip helper inside the gpiolib, make sure
the IRQs are unmapped/disposed before the irqdomain is removed
as part of removing the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a function gpiochip_irqchip_add() to set
up an irqchip for a GPIO controller, and a function
gpiochip_set_chained_irqchip() to chain it to a parent
irqchip.
Most GPIOs are of the type where a number of lines form
a cascaded interrupt controller chained onto
the primary system interrupt controller (or further down the
chain) so let's add this helper and factor the code to
request the lines to be used as IRQs, the .to_irq() function
and the irqdomain into the core as well.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Nothing prevents GPIO drivers from returning values outside the
boolean range, and as it turns out a few drivers are actually doing so.
These values were passed as-is to unsuspecting consumers and created
confusion.
This patch makes the internal _gpiod_get_raw_value() function return a
bool, effectively clamping the GPIO value to the boolean range no
matter what the driver does.
While we are at it, we also change the value parameter of
_gpiod_set_raw_value() to bool type before drivers start doing funny
things with it as well.
Another way to fix this would be to change the prototypes of the driver
interface to use bool directly, but this would require a huge
cross-systems patch so this simpler solution is preferred.
Changes since v1:
- Change local variable type to bool as well, use boolean values in
code
- Also change prototype of open drain/open source setting functions
since they are only called from _gpiod_set_raw_value()
This probably calls for a larger booleanization of gpiolib, but let's
keep that for a latter change - right now we need to address the issue
of non-boolean values returned by drivers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current ACPI GPIO event handling code was never tested against real
hardware with functioning GPIO triggered events (at the time such hardware
wasn't available). Thus it misses certain things like requesting the GPIOs
properly, passing correct flags to the interrupt handler and so on.
This patch reworks ACPI GPIO event handling so that we:
1) Use struct acpi_gpio_event for all GPIO signaled events.
2) Switch to use GPIO descriptor API and request GPIOs by calling
gpiochip_request_own_desc() that we added in a previous patch.
3) Pass proper flags from ACPI GPIO resource to request_threaded_irq().
Also instead of open-coding the _AEI iteration loop we can use
acpi_walk_resources(). This simplifies the code a bit and fixes memory leak
that was caused by missing kfree() for buffer returned by
acpi_get_event_resources().
Since the remove path now calls gpiochip_free_own_desc() which takes GPIO
spinlock we need to call acpi_gpiochip_remove() outside of that lock
(analogous to acpi_gpiochip_add() path where the lock is released before
those funtions are called).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sometimes it is useful to allow GPIO chips themselves to request GPIOs they
own through gpiolib API. One use case is ACPI ASL code that should be able
to toggle GPIOs through GPIO operation regions.
We can't use gpio_request() because it will pin the module to the kernel
forever (it calls try_module_get()). To solve this we move module refcount
manipulation to gpiod_request() and let __gpiod_request() handle the actual
request. This changes the sequence a bit as now try_module_get() is called
outside of gpio_lock (I think this is safe, try_module_get() handles
serialization it needs already).
Then we provide gpiolib internal functions gpiochip_request/free_own_desc()
that do the same as gpio_request() but don't manipulate module refrence
count. This allows the GPIO chip driver to request and free descriptors it
owns without being pinned to the kernel forever.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is currently debated where the functions to lock a certain
GPIO line as used for IRQs should be called. Delete all
misleading documentation.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers dealing with a gpio_chip might need to act on its
descriptors directly; one example is pinctrl drivers that need to lock a
GPIO for being used as IRQ using gpiod_lock_as_irq().
This patch exports a gpiochip_get_desc() function that returns the
GPIO descriptor at the requested index. It also sweeps the
gpio_to_chip() function out of the consumer interface since any holder
of a gpio_chip reference can manipulate its GPIOs way beyond what a
consumer should be allowed to do.
As a result, gpio_chip is not visible anymore to simple GPIO consumers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The documentation was not clear about whether
gpio_direction_output should take a logical value or the physical
level on the output line, i.e. whether the ACTIVE_LOW status
would be taken into account.
This converts gpiod_direction_output to use the logical level
and adds a new gpiod_direction_output_raw for the raw value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A big set this merge window, as we have much going on in
this subsystem. Major changes this time:
- Some core improvements and cleanups to the new GPIO
descriptor API. This seems to be working now so we can
start the exodus to this API, moving gradually away from
the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move
the few GPIO ACPI clients we have to the GPIO descriptor
API right *now* before we go any further. We actually
managed to contain this *before* we started to litter
the kernel with yet another hackish global numberspace for
the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have
been migrated to use the GPIO descriptors rather than
fixed number assignments. Tegra machine has been migrated
as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x.
Those should be really good examples of how I expect a
nice GPIO driver to look these days.
- Do away with custom GPIO implementations on a major
part of the ARM machines: ks8695, lpc32xx, mv78xx0.
Make a first step towards the same in the horribly
convoluted Samsung S3C include forest. We expect to
continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em,
intel-mid and lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line
is used for IRQs and can then enforce some semantics such
as disallowing a GPIO line marked as in use for IRQ to be
switched to output mode.
- Drop all use of irq_set_chip_and_handler_name().
The name provided in these cases were just unhelpful
tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em
74x164 and msm drivers.
- Some non-urgent bug fixes here and there, duplicate
#includes and that usual kind of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lW2i
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
Now that all users of acpi_gpio.h have been moved to use either the GPIO
descriptor interface or to the internal gpiolib.h we can get rid of
acpi_gpio.h entirely.
Once this is done the only interface to get GPIOs to drivers enumerated
from ACPI namespace is the descriptor based interface.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.
We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.
Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some devices drivers make use of optional GPIO parameters. For such
drivers, it is important to discriminate between the case where no
GPIO mapping has been defined for the function they are requesting, and
the case where a mapping exists but an error occured while resolving it
or when acquiring the GPIO.
This patch changes the family of gpiod_get() functions such that they
will return -ENOENT if and only if no GPIO mapping is defined for the
requested function. Other error codes are used when an actual error
occured during the GPIO resolution.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernfs has just been separated out from sysfs and we're already in
full conflict mode. Nothing can make the situation any worse. Let's
take the chance to name things properly.
This patch performs the following renames.
* s/sysfs_elem_dir/kernfs_elem_dir/
* s/sysfs_elem_symlink/kernfs_elem_symlink/
* s/sysfs_elem_attr/kernfs_elem_file/
* s/sysfs_dirent/kernfs_node/
* s/sd/kn/ in kernfs proper
* s/parent_sd/parent/
* s/target_sd/target/
* s/dir_sd/parent/
* s/to_sysfs_dirent()/rb_to_kn()/
* misc renames of local vars when they conflict with the above
Because md, mic and gpio dig into sysfs details, this patch ends up
modifying them. All are sysfs_dirent renames and trivial. While we
can avoid these by introducing a dummy wrapping struct sysfs_dirent
around kernfs_node, given the limited usage outside kernfs and sysfs
proper, I don't think such workaround is called for.
This patch is strictly rename only and doesn't introduce any
functional difference.
- mic / gpio renames were missing. Spotted by kbuild test robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch just accents that @dev could be NULL.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In several places we are printing messages with prefix based on chip->label.
Introduced macros help us to do this easier and in uniform way.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
