Initial device tree support for Qualcomm MSM8992 SoC and
LG Bullhead / Google Nexus 5X support.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch add support to Analog audio both Playback and Capture via
msm8916 WCD muti codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
pm8994 has 22 gpios, so add the missing interrupts entry for one
of the gpios
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
On the APQ8016 SBC, the LDO2 PM8916 regulator feeds 1.2V to the following:
- VDDA_1P2_MIPI_DSI and VDDA_MIPI_CSI pins on APQ8016.
- VCCCAD pins on the LPDDR3 chip.
- VDDPX_1 pins on APQ8016.
The LDO6 regulator feeds 1.8V to:
- VDAA_MIPI_DSI0_PLL pin on APQ8016.
- QFPROM_BLOW_VDD pin on PM8916.
- The AVDD, A2VDD and DVDD pins on ADV7533 bridge.
The LDO17 regulator feeds 3.3V to:
- The V3P3 pin on ADV7533 bridge.
Currently, the regulator min/max voltages for all the LDOs are set to the
range of what the PMIC supports. Set the ranges for L2, L6 and L17 to what
we need, i.e. 1.2V, 1.8V and 3.3V respectively.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds pmic specific dts which are configured specially
for db820c. One of such pin is GPIO_F on the Low Speed expansion
which has default output voltage of 2.7v. This patch fixes setup
for that pin to have an output voltage of 1.8v to comply with
96boards LS expansion specs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Hexagon core on the msm8916 provides services for audio control,
audio output, sensors and the Hexagon SDK. The Hexagon remoteproc node
allows us to boot this core.
Although its part of the core platform its left disabled as it will
crash without the rmtfs QMI service and we do not yet handle crashes
gracefully.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the Hexagon SMD edge, so that QRTR is probed when the Hexagon is
booted.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The APQ8016-sbc provides a HDMI output. The APQ8016 display block only
provides a MIPI DSI output. So, the board has a ADV7533 DSI to HDMI
encoder chip that sits between the DSI PHY output and the HDMI
connector.
Add the ADV7533 DT node under its I2C control bus, and tie the DSI
output port to the ADV7533's input port.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The MSM8916 SoC contains a MDP5 based display block, and one DSI output.
Add the top level MDSS DT node, and the MDP5, DSI and DSI PHY children
sub-blocks. Establish the link between MDP5's INTF1 output port and DSI's
input port.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to external sd card.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to SPI on HS expansion connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to SPI on LS expansion connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to i2c bus on High speed connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to LS_I2C1 on LS expansion connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to LS-I2C0 on LS expansion connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to 4 pin UART0 on LS expansion connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds apq8096 db820c basic support with serial port.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
When a device uses the GIC as its interrupt controller and generates
SPIs, only the values 1 (edge rising) and 4 (level high) are legal.
Anything else is just plain wrong (can't be programmed into the HW),
and leads to aborted driver probes (USB doesn't work with 4.8-rc1
on a Dragonboard 410C).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The TCSR memory segment includes various functionality, among other
things the halt-registers for the Hexagon.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
On msm8916 SCM acts as a controller for the MSS_RESET found in the GCC,
update the DT node so that we can address this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The modem boot authenticator needs space to play in, this is supposed to
be relocatable and as such could later be replaced with a dynamically
allocated chunk of memory. But let's give it a reserve for now, as we
know that works.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the smsm and smp2p nodes for the hexagon and wcnss
cores.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to sdc2 sdhci controller, which is used on some
of the boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds pinctrl required for sdhci for external sd card
controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_spi5 device, which is used in some of
the APQ8096 based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp1_spi0 which is used on some of APQ8096
based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c0, which is used on some of the
APQ8096 based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c0 pinctrl.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c1, which is used in one of the
apq8096 based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c1 pinctrl nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds blsp1_i2c2 support, as this bus is used on some of the
apq8096 boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds bslp2_uart2 node in soc so that boards that use this
uart can enable it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds 2pin and 4 pin uart pinctrl support for blsp2_uart1
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds msmgpio label for pin and gpio controller so that
it can referenced in dedicated pins file and other board level gpios.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Update reserved-memory in accordance with memory the detailed memory map
for 8916, so that we will be able to reference the firmware memory
regions.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the devicetree node for the SCM firmware.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Add the PMU so we can get proper perf event support on this SoC.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device bindings for CPUs to suspend using PSCI as the enable-method.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Tested-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables bam dma node, dma is used for both tx and rx on spi
and on high speed serial.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the necessary properties to enable the SD-card on db410c boards.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The qcom-spmi-mpp driver is now using string "digital" to denote
old "normal" functionality. Update DTS file.
Also update the powersource.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
This patch updates the digital voltage levels from corner values to
microvolts as we are going to use s1 regulator directly for vddcx
instead of s1_corner.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
This patch enables the lpass on DB410C. LPASS is used as cpu dai for
both analog and digital audio.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
This patch adds manual pull up setting for usb otg indicating that the
vbus is vbus is not routed to USB controller/phy therefore enables
pull-up explicitly before starting controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Add the RPM Clock Controller DT node and include the necessary header
file for clocks.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The #size-cells for the pmics are 0, but we specify a size in the
reg property so that MPP and GPIO modules can figure out how many
pins there are. Now that we've done that by counting irqs, we can
remove the size elements in the reg properties and be DT
compliant.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add #power-domain-cells property for both the gcc and mmcc
clock controller nodes as they both supports power domains (gdsc's)
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds real regulators and pinctrl nodes for sdhc_1.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
To be consistent with other nodes move sdhci node under the soc node,
rather than using lable references.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
96boards mezzanine boards on LS expansion require 1.8v as per 96boards
specifications, so enable the corresponding regulators and make them
always-on.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds label to smd rpm regulators so that the board level file
can use the label directly to populate the regulators, rather than
having deep nesting.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
s2 is spmi controller regulator on msm8916 according to downstream 3.10
kernel, so remove it from the dt to avoid confusion an use of it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
2mA drive strenght is not enough to drive chipselect low on hardware
configurations with level shifters, 16mA should give good range to
allow such configurations to work.
This issue was noticed while testing spi on db410c with sensor board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch removes redundant pins from spi pinconf as these are already
specified in pinconf_cs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds aliases to spi device so that it can get proper bus
number rather than a random number.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The msm8916 SoC has an L2 cache for all 4 CPUs. Add it to the
dtsi file so that the cache hierarchy can be probed.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Use the standard name for clock controller nodes instead of a
qcom specific name.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the gpio and MPP devices to the pm8994 pmic dts.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the skeleton nodes for the PMICs found on msm8996-mtp
devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add initial device tree support for the Qualcomm MSM8996 SoC and
MTP8996 evaluation board.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
* Add fixed rate oscillators to dts
* Fixup PMIC alias and properties
* Change 8916-MTP compatible to be compliant with new scheme
* Fix 8x16 UART pinctrl configuration
* Add SMEM, RPM/SMD, and PM8916 support on MSM8916
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mu4g
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64
Qualcomm ARM64 Updates for v4.5
* Add fixed rate oscillators to dts
* Fixup PMIC alias and properties
* Change 8916-MTP compatible to be compliant with new scheme
* Fix 8x16 UART pinctrl configuration
* Add SMEM, RPM/SMD, and PM8916 support on MSM8916
* tag 'qcom-arm64-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: Add PM8916 support on MSM8916
arm64: dts: qcom: Add RPM/SMD support on MSM8916
arm64: dts: qcom: Add MSM8916 SMEM nodes
arm64: dts: set the default i2c pin drive strength to 16mA
arm64: dts: fix the i2c aliasing to match to schematics.
arm64: dts: qcom: msm8916: Add fixed rate on-board oscillators
arm64: dts: qcom: Alias pm8916 on msm8916 devices
arm64: dts: qcom: Make msm8916-mtp compatible string compliant
arm64: dts: qcom: 8x16: UART1 and UART2 use DMA for RX and TX
arm64: dts: qcom: 8x16: UART1 add CTS_N, RTS_N pin configurations
Signed-off-by: Olof Johansson <olof@lixom.net>
Add label properties to provide a way to identify UART, I2C and SPI
ports based on their connector names. This follows naming convention in
96boards CE spec. Ports without external connections are not labelled.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Andy Gross <agross@codeaurora.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The LS UART0 is not used by anything else and should be enabled for
expansion boards.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Andy Gross <agross@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the PM8916 regulator nodes found on MSM8916 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Add support for the SMD and RPM devices found on MSM8916 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This patch adds the nodes necessary to support the SMEM driver on MSM8916
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
2mA drive strength is not enough when we connect multiple i2c devices
on the bus with different pull up resistors.
This issue was detected when multiple i2c devices connected on the other side
of level shifters on Linaro sensor board. Maxing up to 16mA made i2c much stable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes the i2c bus number aliasing so that it matches with the
schematics bus naming.
Without this patch the user might would get bus numbers depending on
the order the devices are probed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Currently the rates of the xo and sleep clocks are hard-coded in the
GCC driver, but this is a board layout description that actually should
be in the DT. Moving them into DT also allows us to insert the RPM
controlled clocks between the DT and GCC clocks.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add an alias for pm8916 on msm8916 based SoCs so that the newly
updated dtbTool can find the pmic compatible string and add the
pmic-id element to the QCDT header.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This compatible string isn't compliant with the format for
subtypes. Replace it with a compliant compatible type.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add DMA channels definitions for UART1 and UART2 controllers.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add devicetree bindings for UART1 CTS_N and RTS_N pins.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
* Add RNG device tree node
* Add MSM8x16 serial UART1 node
* Enable eMMC on apq8016-sbc board
* Fix I2C pinconf sleep state function
* Add MSM8916 I2C nodes
* Enable I2C busses on LS and HS on APQ8016-sbc
* Enable SPI busses on LS and HS on APQ8016-sbc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pMvh
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm into next/dt
Pull "Qualcomm ARM64 Updates for v4.4" from Andy Gross:
* Add RNG device tree node
* Add MSM8x16 serial UART1 node
* Enable eMMC on apq8016-sbc board
* Fix I2C pinconf sleep state function
* Add MSM8916 I2C nodes
* Enable I2C busses on LS and HS on APQ8016-sbc
* Enable SPI busses on LS and HS on APQ8016-sbc
* tag 'qcom-arm64-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm:
arm64: dts: apq8016-sbc: enable spi buses on LS and HS
arm64: dts: apq8016-sbc: enable i2c buses on LS and HS
arm64: dts: qcom: Add msm8916 I2C nodes.
arm64: dts: fix i2c pinconf sleep state function
arm64: dts: qcom: Enable eMMC on apq8016-sbc board
arm64: dts: qcom: Add 8x16 Serial UART1 node
arm64: dts: qcom: Add RNG device tree node
This patch enables spi buses on low speed and high speed expansion
connectors on DB410C
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch enables i2c buses on low speed and high speed expansion
connectors on DB410C.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds missing support for i2c0 and i2c6, this support is
required to connect the i2c slaves on LS expansion on DB410c.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch fixes the i2c pinctrl sleep state by changing the pinconf
function to be in gpio mode rather than i2c.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Enable the eMMC on the APQ8016 SBC board (also known as DragonBoard 410c),
so that we can use its internal storage.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds the nodes required to support the UART1 node on the
MSM8916 and also fixes the sleep pins function for UART2.
Signed-off-by: Andy Gross <agross@codeaurora.org>
clock controller nodes which also support power domains (gdscs') need
to have a #power-domain-cells property. Add these for gcc and mmcc
nodes of msm8974, gcc of apq8084 and msm8916.
Also update gcc and mmcc bindings for it.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
APQ8016 SBC board have 6 user controllable LED's.
Add following devices:
LED1 green LED triggered by system heartbeat.
LED2 green LED triggered by access to eMMC device.
LED3 green LED triggered by access to SD card.
LED4 green LED no trigger assigned.
LED5 yellow LED triggered by access to WLAN.
LED6 blue LED triggered by access to Bluetooth.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
USB2513B HUB reset line is connected to PMIC GPIO3 not GPIO1.
Fix TC7USB40MU Dual SPDT Switch select input line control, which is
connected to PMIC GPIO4 not GPIO2 and disable the pin. It is not used
for now.
Remove user LEDs definitions, because they clash with above numbers.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Hogging pins from pinctrl driver prevents client drivers
to probe.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
