Commit ea7dce901 ("drm/nv50/gr: print mpc trap name when it's not an mp
trap") added an nv_error call that was missing the priv parameter. This
causes GPFs if the error is ever hit.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Address of the ENG_RUNLIST register should be 0x002284 + (engine * 8),
not 0x002284 + (engine * 4).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
See https://bugs.freedesktop.org/show_bug.cgi?id=74492
Reported-by: Ronald <ronald645@gmail.com>
Suggested-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Since commit 0fa9061ae8 ("drm/nouveau/mc: handle irq-related setup
ourselves"), drm_device->irq_enabled remained unset. This is needed in
order to properly wait for a vblank event in the generic drm code.
See https://bugs.freedesktop.org/show_bug.cgi?id=74195
Reported-by: Jan Janecek <janjanjanx@gmail.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add DSB after icache flush to complete the cache maintenance operation.
Signed-off-by: Vinayak Kale <vkale@apm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We must use a 64-bit for this, otherwise overflowed bits get lost, and
that can result in a lower than intended value set.
Fixes: 8e0cb8a1f6 ("ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Fixes: 7d35496dd9 ("ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Tested-Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ERROR: spaces required and "(foo*)" should be "(foo *)"
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace two magic numbers which intialize clgstate::state.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit 89aef8921bf("ipv4: Delete routing cache."), the counter
in_slow_tot can't work correctly.
The counter in_slow_tot increase by one when fib_lookup() return successfully
in ip_route_input_slow(), but actually the dst struct maybe not be created and
cached, so we can increase in_slow_tot after the dst struct is created.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Ceph fixes from Sage Weil:
"We have some patches fixing up ACL support issues from Zheng and
Guangliang and a mount option to enable/disable this support. (These
fixes were somewhat delayed by the Chinese holiday.)
There is also a small fix for cached readdir handling when directories
are fragmented"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix __dcache_readdir()
ceph: add acl, noacl options for cephfs mount
ceph: make ceph_forget_all_cached_acls() static inline
ceph: add missing init_acl() for mkdir() and atomic_open()
ceph: fix ceph_set_acl()
ceph: fix ceph_removexattr()
ceph: remove xattr when null value is given to setxattr()
ceph: properly handle XATTR_CREATE and XATTR_REPLACE
Pull CIFS fixes from Steve French:
"Three cifs fixes, the most important fixing the problem with passing
bogus pointers with writev (CVE-2014-0069).
Two additional cifs fixes are still in review (including the fix for
an append problem which Al also discovered)"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix too big maxBuf size for SMB3 mounts
cifs: ensure that uncached writes handle unmapped areas correctly
[CIFS] Fix cifsacl mounts over smb2 to not call cifs
When FS-Cache allocates an object, the following sequence of events can
occur:
-->fscache_alloc_object()
-->cachefiles_alloc_object() [via cache->ops->alloc_object]
<--[returns new object]
-->fscache_attach_object()
<--[failed]
-->cachefiles_put_object() [via cache->ops->put_object]
-->fscache_object_destroy()
-->fscache_objlist_remove()
-->rb_erase() to remove the object from fscache_object_list.
resulting in a crash in the rbtree code.
The problem is that the object is only added to fscache_object_list on
the success path of fscache_attach_object() where it calls
fscache_objlist_add().
So if fscache_attach_object() fails, the object won't have been added to
the objlist rbtree. We do, however, unconditionally try to remove the
object from the tree.
Thanks to NeilBrown for finding this and suggesting this solution.
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: (a customer of) NeilBrown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has been this way for years, and every time I stumble across it I
lose my lunch. After coming across it for the nth time in the Coverity
results, I had to overcome the bystander effect and do something about
it.
This ignores the 79 column limit in favor of making it look like C
instead of gibberish.
The correct thing to do here would be to lose some of the indentation by
breaking this function up into several smaller ones. I might do that at
some point if I have the stomach to look at this again.
(Also some of those overlong ternary operations would likely be more
readable as regular if's)
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Phoebe Buckheister says:
====================
ieee802154: support rf212 and extended mac features
this patch set adds support for the RF212 radio chip to the existing
at86rf230 driver and adds support for numerous features of the RF212
chips to the ieee802154 stack. These features include CSMA parameter
configuration, transmit power control, CCA parameter configuration, and
automatic retransmission of frames. Netlink APIs are provided for all
new options introduced in this set.
Many features might also work for RF230, but since I have no such chips
at my disposal, most new features are implemented only for RF212.
Changes since v2:
* Indentation
Changes since v1:
* CodingStyle compliance. Thanks Sergei Shtylyov
* Add CSMA parameters to netlink phy list that were forgotten in v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does multiple things:
* add .set_csma_params and .set_frame_retries for the RF212 radio.
This should work fine with RF230, but since I have no RF230 radios to
test with, RF230 does not implement these right now
* enable TX_ARET for frame retransmission limits greater than -1
Since RF230 has no operations to change CSMA parameters or frame retry
limits, RF230 will not be able to enter TX_ARET with this patch.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new netlink attributes for SET_PHY_ATTRS:
* CSMA minimal backoff exponent
* CSMA maximal backoff exponent
* CSMA retry limit
* frame retransmission limit
The CSMA attributes shall correspond to minBE, maxBE and maxCSMABackoffs of
802.15.4, respectively. The frame retransmission shall correspond to
maxFrameRetries of 802.15.4, unless given as -1: then the old behaviour
of the stack shall apply. For RF2xy, the old behaviour is to not do
channel sensing at all and simply send *right now*, which is not
intended behaviour for most applications and actually prohibited for
some channel/page combinations.
For all values except frame retransmission limit, the defaults of
802.15.4 apply. Frame retransmission limits are set to -1 to indicate
backward-compatible behaviour.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A documented erratum of the RF212 chip describes that some versions of
RF212 may not be properly reset by the standard reset procedure. The
described workaround seems to not fully work either; my RF212 chips will
not correctly receive any frames unless they are taken from RX mode to
TRX_OFF and back to RX mode, effectively forcing a up-down-up-cycle.
Going to TRX_OFF and to RX without intermediate state changes at least
once fixes this.
The same transition is allowed for RF230, so simply do it all the time.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.
For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard assigns channel 0 on page 2 to be 100kbps QPSK in the
868.3MHz band. Add support to the at86rf230 driver for this channel and
page, at the moment predicated only for the RF212 chip.
Per the datasheet, configurations for page 0, channels 0 to 10 and page
2, channels 0 to 10 differ only in the BPSK_QPSK bit. Support for
channels 1 to 10 is untested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.
This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IEEE802.15.4 stack assumes that a radio will never deliver
packets with a bad CRC into the stack, as required by the standard.
at86rf230 driven radios violates this assumption because of another
incompatibility: devices are required to send ACKs if requested by a
sender, but RF2xx will only send ACKs from a special receive mode that
is currently not used by the driver.
Enable this receive mode to fix both bugs. Frames with bad CRCs will not
be received at all, and ACKs will be sent if so requested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the AT86RF2xy chips are mostly compatible, this is only a small
change to the actual driver code. The at86rf230 driver already supports the
RF212 in most places, only three small adjustments are required:
* force the initial state after P_ON to FORCE_TRX_OFF to work around a
documented erratum
* channels_supported depends on the frequency of the transceiver, and
thus is_rf212
* do early detection of chip version select an appropriate _ops struct
based on the chip version.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: soft reset rework for 10G PHYs
As reported by Shaohui, 10G PHYs may have a slightly more complex reset
sequence for which a BMCR_RESET software reset might not suffice. This
patchset offers a solution for those by allowing them to implement their
own soft_reset() callback. Finally there is an update to the PHY library
Documentation to cover for the newly added callbacks of the PHY driver
structure.
Changes in v2:
- fixed callback testing
- fixed typo in Documentation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library was missing a bunch of newly added PHY driver callbacks
along with a smallish description of what they do, fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Shaohui, most 10G PHYs out there have a non-standard
compliant software reset sequence, eventually something much more
complex than just toggling the BMCR_RESET bit. Allow PHY driver to
implement their own soft_reset() callback to deal with that. If no
callback is provided, call into genphy_soft_reset() which makes sure the
existing behavior is kept intact.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Shaohui, this function is generic for 10/100/1000
PHYs, but 10G PHYs might have a slightly different reset sequence which
prevents most of them from using this function.
Move the BMCR_RESET based software resent sequence to
genphy_soft_reset() in preparation for allowing PHY drivers to implement
a soft_reset() callback.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the buffer allocation in the receive path for normal packets.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the receive path a little more efficient by parameterizing the
required state rather than re-establishing that state.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure is redundant; get rid of it make the code little more efficient -
get rid of the unnecessary indirection.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing set_termios() from irtty_close() causes kernel Oops for
unplugged usb-serial devices.
Since no other tty_ldisc calls set_termios() on close and no tty driver
seem to check if tty->device_data is NULL or not on entry to set_termios(),
the only solution I can come up with is to remove the irtty_stop_receiver()
call, which only updates termios.
Signed-off-by: Tommie Gannert <tommie@gannert.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull AVR32 fixes from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: add generic vga.h to Kbuild
avr32: add generic ioremap_wc() definition in io.h
avr32: Makefile: add '-D__linux__' flag for gcc-4.4.7 use
avr32: fix missing module.h causing build failure in mimc200/fram.c
If directory is fragmented, readdir() read its dirfrags one by one.
After reading all dirfrags, the corresponding dentries are sorted in
(frag_t, off) order in the dcache. If dentries of a directory are all
cached, __dcache_readdir() can use the cached dentries to satisfy
readdir syscall. But when checking if a given dentry is after the
position of readdir, __dcache_readdir() compares numerical value of
frag_t directly. This is wrong, it should use ceph_frag_compare().
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Make the 'acl' option dependent on having ACL support compiled in. Make
the 'noacl' option work even without it so that one can always ask it to
be off and not error out on mount when it is not supported.
Signed-off-by: Guangliang Zhao <lucienchao@gmail.com>
Signed-off-by: Sage Weil <sage@inktank.com>
If acl is equivalent to file mode permission bits, ceph_set_acl()
needs to remove any existing acl xattr. Use __ceph_setxattr() to
handle both setting and removing acl xattr cases, it doesn't return
-ENODATA when there is no acl xattr.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
For the setxattr request, introduce a new flag CEPH_XATTR_REMOVE
to distinguish null value case from the zero-length value case.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
return -EEXIST if XATTR_CREATE is set and xattr alread exists.
return -ENODATA if XATTR_REPLACE is set but xattr does not exist.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Pull powerpc fixes from Ben Herrenschmidt:
"Here are some more powerpc fixes for 3.14
The main one is a nasty issue with the NUMA balancing support which
requires a small generic change and the addition of a new accessor to
set _PAGE_NUMA. Both have been reviewed and acked by Mel and Rik.
The changelog should have plenty of details but basically, without
this fix, we get random user segfaults and/or corruptions due to
missing TLB/hash flushes. Aneesh series of 3 patches fixes it.
We have some vDSO vs. perf fixes from Anton, some small EEH fixes
from Gavin, a ppc32 regression vs the stack overflow detector, and a
fix for the way we handle PCIe host bridge speed settings on pseries
(which is needed for proper operations of AMD graphics cards on
Power8)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Disable EEH on reboot
powerpc/eeh: Cleanup on eeh_subsystem_enabled
powerpc/powernv: Rework EEH reset
powerpc: Use unstripped VDSO image for more accurate profiling data
powerpc: Link VDSOs at 0x0
mm: Use ptep/pmdp_set_numa() for updating _PAGE_NUMA bit
mm: Dirty accountable change only apply to non prot numa case
powerpc/mm: Add new "set" flag argument to pte/pmd update function
powerpc/pseries: Add Gen3 definitions for PCIE link speed
powerpc/pseries: Fix regression on PCI link speed
powerpc: Set the correct ksp_limit on ppc32 when switching to irq stack
