An ARC700 customer reported linux boot crashes when upgrading to bigger
L1 dcache (64K from 32K). Turns out they had an aliasing VIPT config and
current code only assumed 2 colours, while theirs had 4. So default to 4
colours and complain if there are fewer. Ideally this needs to be a
Kconfig option, but heck that's too much of hassle for a single user.
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Historical MMU revisions have been paired with Cache revision updates
which are captured in MMU and Cache Build Configuration Registers respectively.
This was used in boot code to check for configurations mismatches,
speically in simulations (such as running with non existent caches,
non pairing MMU and Cache version etc). This can instead be inferred
from other cache params such as line size. So remove @ver from post
processed @cpuinfo which could be used later to save soem other
interesting info.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Patch series "Add support for DMA writable pages being writable by the
network stack", v3.
The first 19 patches in the set add support for the DMA attribute
DMA_ATTR_SKIP_CPU_SYNC on multiple platforms/architectures. This is
needed so that we can flag the calls to dma_map/unmap_page so that we do
not invalidate cache lines that do not currently belong to the device.
Instead we have to take care of this in the driver via a call to
sync_single_range_for_cpu prior to freeing the Rx page.
Patch 20 adds support for dma_map_page_attrs and dma_unmap_page_attrs so
that we can unmap and map a page using the DMA_ATTR_SKIP_CPU_SYNC
attribute.
Patch 21 adds support for freeing a page that has multiple references
being held by a single caller. This way we can free page fragments that
were allocated by a given driver.
The last 2 patches use these updates in the igb driver, and lay the
groundwork to allow for us to reimplement the use of build_skb.
This patch (of 23):
This change allows us to pass DMA_ATTR_SKIP_CPU_SYNC which allows us to
avoid invoking cache line invalidation if the driver will just handle it
later via a sync_for_cpu or sync_for_device call.
Link: http://lkml.kernel.org/r/20161110113419.76501.38491.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We used to use generic implementation of dma_map_ops.mmap which is
dma_common_mmap() but that only worked for simpler cached mappings when
vaddr = paddr.
If a driver requests uncached DMA buffer kernel maps it to virtual
address so that MMU gets involved and page uncached status takes into
account. In that case usage of dma_common_mmap() lead to mapping of
vaddr to vaddr for user-space which is obviously wrong. For more detals
please refer to verbose explanation here [1].
So here we implement our own version of mmap() which always deals
with dma_addr and maps underlying memory to user-space properly
(note that DMA buffer mapped to user-space is always uncached
because there's no way to properly manage cache from user-space).
[1] https://lkml.org/lkml/2016/10/26/973
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> #4.5+
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously we would not print the case when IOC existed but was not
enabled.
And while at it, reduce one line off boot printing by consolidating
the Peripheral address space and IO-Coherency which in a way
applies to them
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
if user disables IOC from debugger at startup (by clearing @ioc_enable),
@ioc_exists is cleared too. This means boot prints don't capture the
fact that IOC was present but disabled which could be misleading.
So invert how we use @ioc_enable and @ioc_exists and make it more
canonical. @ioc_exists represent whether hardware is present or not and
stays same whether enabled or not. @ioc_enable is still user driven,
but will be auto-disabled if IOC hardware is not present, i.e. if
@ioc_exist=0. This is opposite to what we were doing before, but much
clearer.
This means @ioc_enable is now the "exported" toggle in rest of code such
as dma mapping API.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HS release 3.0 provides for even more flexibility in specifying the
volatile address space for mapping peripherals.
With HS 2.1 @start was made flexible / programmable - with HS 3.0 even
@end can be setup (vs. fixed to 0xFFFF_FFFF before).
So add code to reflect that and while at it remove an unused struct
defintion
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For resources shared by all cores such as SLC and IOC, only the master
core needs to do any setups / enabling / disabling etc.
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Things have been calm here - nothing much except for a few fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/rhI
-----END PGP SIGNATURE-----
Merge tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Things have been calm here - nothing much except for a few fixes"
* tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: don't loose PTE_SPECIAL in pte_modify()
ARC: dma: fix address translation in arc_dma_free
ARC: typo fix in mm/ioremap.c
ARC: fix linux-next build breakage
page should be calculated using physical address.
If platform uses non-trivial dma-to-phys memory translation,
dma_handle should be converted to physicval address before
calculation of page.
Failing to do so results in struct page * pointing to
wrong or non-existent memory.
Fixes: f2e3d55397 ("ARC: dma: reintroduce platform specific dma<->phys")
Cc: stable@vger.kernel.org #4.6+
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
NPS use special mapping right below TASK_SIZE.
Hence we need to lower STACK_TOP so that user stack won't
overlap NPS special mapping.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
On ARC, lower 2G of address space is translated and used for
- user vaddr space (region 0 to 5)
- unused kernel-user gutter (region 6)
- kernel vaddr space (region 7)
where each region simply represents 256MB of address space.
The kernel vaddr space of 256MB is used to implement vmalloc, modules
So far this was enough, but not on EZChip system with 4K CPUs (given
that per cpu mechanism uses vmalloc for allocating chunks)
So allow VMALLOC_SIZE to be configurable by expanding down into the unused
kernel-user gutter region which at default 256M was excessive anyways.
Also use _BITUL() to fix a build error since PGDIR_SIZE cannot use "1UL"
as called from assembly code in mm/tlbex.S
Signed-off-by: Noam Camus <noamc@ezchip.com>
[vgupta: rewrote changelog, debugged bootup crash due to int vs. hex]
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Initial HIGHMEM support on ARC was introduced for PAE40 where the low
memory (0x8000_0000 based) and high memory (0x1_0000_0000) were
physically contiguous. So CONFIG_FLATMEM sufficed (despite a peipheral
hole in the middle, which wasted a bit of struct page memory, but things
worked).
However w/o PAE, highmem was not possible and we could only reach
~1.75GB of DDR. Now there is a use case to access ~4GB of DDR w/o PAE40
The idea is to have low memory at canonical 0x8000_0000 and highmem
at 0 so enire 4GB address space is available for physical addressing
This needs additional platform/interconnect mapping to convert
the non contiguous physical addresses into linear bus adresses.
From Linux point of view, non contiguous divide means FLATMEM no
longer works and DISCONTIGMEM is needed to track the pfns in the 2
regions.
This scheme would also work for PAE40, only better in that we don't
waste struct page memory for the peripheral hole.
The DT description will be something like
memory {
...
reg = <0x80000000 0x200000000 /* 512MB: lowmem */
0x00000000 0x10000000>; /* 256MB: highmem */
}
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The peripheral address space is architectural address window which is
uncached and typically used to wire up peripherals.
For ARC700 cores (ARCompact ISA based) this was fixed to 1GB region
0xC000_0000 - 0xFFFF_FFFF.
For ARCv2 based HS38 cores the start address is flexible and can be
0xC, 0xD, 0xE, 0xF 000_000 by programming AUX_NON_VOLATILE_LIMIT reg
(typically done in bootloader)
Further in cas of PAE, the physical address can extend beyond 4GB so
need to confine this check, otherwise all pages beyond 4GB will be
treated as uncached
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously a non-coherent page (hardware IOC or simply driver needs)
could be handled by cpu with paddr alone (kvaddr used to be needed for
coherent mappings to enforce uncached semantics via a MMU mapping).
Now however such a page might still require a V-P mapping if it was in
physical address space > 32bits due to PAE40, which the CPU can't access
directly with a paddr
So decouple decision of kvaddr allocation from type of alloc request
(coh/non-coh)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
vs. the ones which reutne void *, so that we can handle pages > 4GB
in subsequent patches
Also plug a potential page leak in case ioremap fails
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Let's define page_mapped() to be true for compound pages if any
sub-pages of the compound page is mapped (with PMD or PTE).
On other hand page_mapcount() return mapcount for this particular small
page.
This will make cases like page_get_anon_vma() behave correctly once we
allow huge pages to be mapped with PTE.
Most users outside core-mm should use page_mapcount() instead of
page_mapped().
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| WARNING: vmlinux.o(.text+0xd6c2): Section mismatch in reference from the function alloc_kmap_pgtable() to the function
| .init.text:__alloc_bootmem_low()
The function alloc_kmap_pgtable() references the function __init __alloc_bootmem_low().
This is often because alloc_kmap_pgtable lacks a __init annotation or the annotation of __alloc_bootmem_low is wrong.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HIGHMEM support bumped the default memory size for nsim platform to 1G.
Thus total memory ended at the very edge of start of peripherals address
space. With linux link base shifted, memory started bleeding into
peripheral space which caused early boot bad_page spew !
Fixes: 29e332261d ("ARC: mm: HIGHMEM: populate high memory from DT")
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARCompact and ARCv2 only have ASL, while binutils used to support LSL as
a alias mnemonic.
Newer binutils (upstream) don't want to do that so replace it.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This is the first working implementation of 40-bit physical address
extension on ARCv2.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
That way a single flip of phys_addr_t to 64 bit ensures all places
dealing with physical addresses get correct data
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Implement kmap* API for ARC.
This enables
- permanent kernel maps (pkmaps): :kmap() API
- fixmap : kmap_atomic()
We use a very simple/uniform approach for both (unlike some of the other
arches). So fixmap doesn't use the customary compile time address stuff.
The important semantic is sleep'ability (pkmap) vs. not (fixmap) which
the API guarantees.
Note that this patch only enables highmem for subsequent PAE40 support
as there is no real highmem for ARC in pure 32-bit paradigm as explained
below.
ARC has 2:2 address split of the 32-bit address space with lower half
being translated (virtual) while upper half unstranslated
(0x8000_0000 to 0xFFFF_FFFF). kernel itself is linked at base of
unstranslated space (i.e. 0x8000_0000 onwards), which is mapped to say
DDR 0x0 by external Bus Glue logic (outside the core). So kernel can
potentially access 1.75G worth of memory directly w/o need for highmem.
(the top 256M is taken by uncached peripheral space from 0xF000_0000 to
0xFFFF_FFFF)
In PAE40, hardware can address memory beyond 4G (0x1_0000_0000) while
the logical/virtual addresses remain 32-bits. Thus highmem is required
for kernel proper to be able to access these pages for it's own purposes
(user space is agnostic to this anyways).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Before we plug in highmem support, some of code needs to be ready for it
- copy_user_highpage() needs to be using the kmap_atomic API
- mk_pte() can't assume page_address()
- do_page_fault() can't assume VMALLOC_END is end of kernel vaddr space
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Move the verbosity knob from .data to .bss by using inverted logic
- No need to readout PD1 descriptor
- clip the non pfn bits of PD0 to avoid clipping inside the loop
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
