While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().
If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.
This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.
This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.
Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In genphy_config_eee_advert, the return value of phy_read_mmd_indirect is
checked to know if the register could be accessed but the result is
assigned to a 'u32'.
Changing to 'int' to correctly get errors from phy_read_mmd_indirect.
Fixes: d853d145ea ("net: phy: add an option to disable EEE advertisement")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From : Woojung Huh <woojung.huh@microchip.com>
Add functions to unregister phy fixup for modules.
int phy_unregister_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list per bus_id, phy_uid &
phy_uid_mask
int phy_unregister_fixup_for_uid(u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_uid()
int phy_unregister_fixup_for_id(const char *bus_id)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_id()
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e3aaf6494 ("phy: fix mdiobus module safety") fixed the way we
dealt with MDIO bus module reference count, but sort of introduced a
regression in that, if an Ethernet driver registers its own MDIO bus
driver, as is common, we will end up with the Ethernet driver's
module->refnct set to 1, thus preventing this driver from any removal.
Fix this by comparing the network device's device driver owner against
the MDIO bus driver owner, and only if they are different, increment the
MDIO bus module refcount.
Fixes: 3e3aaf6494 ("phy: fix mdiobus module safety")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the documentation, the PHYs supported by this driver
can also support pause frames. Announce this to be so.
Tested with a TI83822I.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Vitesse VSC8572 which is functionally equivalent to
the already supported VSC8574. As such, all the same handling functions
are used since the VSC8572 merely has half the number of phy blocks
internally.
Signed-off-by: Stephen Agate <stephen.agate@uk.thalesgroup.com>
Signed-off-by: Neill Whillans <neill.whillans@codethink.co.uk>
Reviewed-by: Daniel Silverstone <daniel.silverstone@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers to have an eth_tp_mdix_ctrl to indicate what is the configured
MDI setting, and read eth_tp_mdi to indicate what is the current status,
Add new parameter mdix_ctrl in phy_device structure and fix driver.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To connect two ports of the same configuration (MDI to MDI or
MDI-X to MDI-X) with a 10/100/1000 Mbit/s connection, an
Ethernet crossover cable is needed to cross over the transmit
and receive signals in the cable, so that they are matched at
the connector level.
When connecting an MDI port to an MDI-X port a straight through
cable is used while to connect two MDI ports or two MDI-X ports
a crossover cable must be used. Conventionally MDI is used on end
devices while MDI-X is used on hubs and switches
Auto MDI-X automatically detects the required cable connection
type and configures the connection appropriately, removing the
need for crossover cables to interconnect switches or connecting
PCs peer-to-peer.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the mdix and mdix_ctrl with corresponding ethtool configuration
parameters.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom BCM7xxx internal PHYs can leverage the Broadcom PHY library
module PHY error counters helper functions, just implement the
appropriate PHY driver function calls to do so. We need to allocate some
storage space for our PHY statistics, and provide it to the Broadcom PHY
library, so do this in a specific probe function, and slightly wrap the
get_stats function call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom PHYs expose a number of PHY error counters: receive errors,
false carrier sense, SerDes BER count, local and remote receive errors.
Add support code to allow retrieving these error counters. Since the
Broadcom PHY library code is used by several drivers, make it possible
for them to specify the storage for the software copy of the statistics.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device_release_driver(&phydev->mdio.dev) is called, it releases all
resources belonging to the PHY device. Hence the subsequent call to
phy_led_triggers_unregister() will access already freed memory when
unregistering the LEDs.
Move the call to phy_led_triggers_unregister() before the possible call
to device_release_driver() to fix this.
Fixes: 2e0bc452f4 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.
On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. There are dedicated phy-modes which tell the
PHY driver to enable the RX and/or TX delays:
- PHY_INTERFACE_MODE_RGMII should disable the RX and TX delay in the
PHY (if required, the MAC should add the delays in this case)
- PHY_INTERFACE_MODE_RGMII_ID should enable RX and TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_TXID should enable the TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_RXID should enable the RX delay in the PHY
(currently not supported by RTL8211F)
With this patch we enable the TX delay for PHY_INTERFACE_MODE_RGMII_ID
and PHY_INTERFACE_MODE_RGMII_TXID.
Additionally we now explicity disable the TX-delay, which seems to be
enabled automatically after a hard-reset of the PHY (by triggering it's
reset pin) to get a consistent state (as defined by the phy-mode).
This fixes a compatibility problem with some SoCs where the TX-delay was
also added by the MAC. With the TX-delay being applied twice the TX
clock was off and TX traffic was broken or very slow (<10Mbit/s) on
1000Mbit/s links.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy_init_hw() fails at phy_attach_direct();
- phy_detach() calls phy_led_triggers_unregister() without
previous call of phy_led_triggers_register().
- still call phy_led_triggers_register() and cause memory leak.
Fixes: 2e0bc452f4 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers should be able to rely on the caller of {get,set}_tunable to
have acquired the PHY device mutex, in order to both serialize against
concurrent calls of these functions, but also against PHY state machine
changes. All ethtool PHY-level functions do this, except
{get,set}_tunable, so we make them consistent here as well.
We need to update the Microsemi PHY driver in the same commit to avoid
introducing either deadlocks, or lack of proper locking.
Fixes: 968ad9da7e ("ethtool: Implements ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE")
Fixes: 310d9ad57a ("net: phy: Add downshift get/set support in Microsemi PHYs driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the downshift/Wirespeed enable/disable
toggles and specify a link retry value ranging from 1 to 9. Since the
integrated BCM7xxx have issues when wirespeed is enabled and EEE is also
enabled, we do disable EEE if wirespeed is enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to need these functions to implement support for Broadcom
Wirespeed, aka downshift.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to generate trace events for mdio read and write accesses.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix setting of SUPPORTED_FIBRE bit as it was not present in features
of KSZ8041.
Signed-off-by: Kirill Esipov <yesipov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate mdix code to phy driver to be called at config_init().
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the phy tunable function pointers and implement downshift
functionality for MSCC PHYs.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the of_node reference taken in fixed_phy_register()
when deregistering a PHY.
Fixes: a759512174 ("net: phy: extend fixed driver with
fixed_phy_register()")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With RGMII, we need a 1.5 to 2ns skew between clock and data lines. The
VSC8601 can handle this internally. While the VSC8601 can set more
fine-grained delays, the standard skew settings work out of the box.
The same heuristic is used to determine when this skew should be enabled
as in vsc824x_config_init().
Tested on custom board with AM3352 SOC and VSC801 PHY.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function just calls into genphy_restart_aneg() to perform an
autonegotation restart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it is useful to know which MDIO driver is being registered, demote
the pr_info() to a pr_debug().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of remembering if the page was changed, just compare the current
page to the saved one. This is easier and has the advantage to save a
register write if the page was already restored.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make phy_aneg_done() available to drivers so that the result of the
auto-negotiation initiated by phy_start_aneg() can be determined.
Remove the local implementation of phy_aneg_done() from the Aeroflex
driver and use the phy library version.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dp83640 has a frequency resolution of about 0.029 ppb.
This patch lets users of the device benefit from the
increased frequency resolution when tuning the clock.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for the Internal RMII PHY found in the Amlogic Meson GXL SoCs.
This PHY seems to only implement some standard registers and need some
workarounds to provide autoneg values from vendor registers.
Some magic values are currently used to configure the PHY, and this a
temporary setup until clarification about these registers names and
registers fields are provided by Amlogic.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support PHY switching on Amlogic GXL SoCs, add support for
16bit and 32bit registers sizes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from phy_connect() and phy_attach().
Note that both function still take a reference to the phy device
through phy_attach_direct().
Fixes: e13934563d ("[PATCH] PHY Layer fixup")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.
Inspired-by: Vikas Soni <vsoni@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to read the AUXCTL register for the BCM54xx. This
mirrors the bcm54xx_auxctl_write function already present in the code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This PHY has a compatible register set with DP83848x so
add support for it.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a definition for PHY ID mask for improving code readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SGMII mode, we observed an autonegotiation issue
after power-down-up cycles where the copper side
reports successful link establishment but the
SGMII side's link is down.
This happened in a setup where the at8031 is
connected over SGMII to a eTSEC (fsl gianfar),
but so far could not be reproduced with other
Ethernet device / driver combinations.
This commit adds a wrapper function for at8031
that in case of operating in SGMII mode double
checks SGMII link state when generic aneg_done()
succeeds. It prints a warning on failure but
intentionally does not try to recover from this
state. As a result, if you ever see a warning
'803x_aneg_done: SGMII link is not ok' you will
end up having an Ethernet link up but won't get
any data through. This should not happen, if it
does, please contact the module maintainer.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
