request_irq() is preferred over setup_irq(). Invocations of setup_irq()
occur after memory allocators are ready.
Per tglx[1], setup_irq() existed in olden days when allocators were not
ready by the time early interrupts were initialized.
Hence replace setup_irq() by request_irq().
[1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanos
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Message-Id: <20200304005049.5291-1-afzal.mohd.ma@gmail.com>
[heiko.carstens@de.ibm.com: replace pr_err with panic]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Improve /proc/interrupts on s390 to show statistics for individual
MSI interrupts.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Both css_evaluate_new_subchannel and cio_validate_subchannel used
stsch and css_sch_is_valid to check for a valid device.
Reduce stsch calls during subchannel evaluation by re-using schib
data. Also the type/devno valid information is only checked once.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In css_alloc_subchannel we allocate the subchannel and do a
validation of the subchannel (to decide if we should look for
devices via this subchannel). On a typical LPAR we find lots
of subchannels to be invalid (because there is no device
attached or the device is blacklisted) leading to lots of
useless kmalloc and kfree calls.
This patch changes the order to only allocate the subchannels
that have been found valid.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
diag308 set has been available for many machine generations, and
alternative reipl code paths has not been exercised and seems to be
broken without noticing for a while now. So, cleaning up all obsolete
reipl methods except currently used ones, assuming that diag308 set
always works.
Also removing not longer needed reset callbacks.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For both ccw and fcp boot retrieve ipl info from ipl block received via
diag308 store. Old scsi ipl parm block handling and cio_get_iplinfo are
removed. Ipl type is deducted from ipl block (if valid).
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the kernel-doc usage in cio to get rid of (W=1) build warnings like:
drivers/s390/cio/cio.c:1068: warning: No description found for parameter 'sch'
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/s390/cio/ files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Export the common I/O interfaces those are needed by an I/O
subchannel driver to actually talk to the subchannel.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Message-Id: <20170317031743.40128-3-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
For future code reuse purpose, this decouples the cio code with
the ccw device specific parts from ccw_device_cancel_halt_clear,
and makes a new common I/O interface named cio_cancel_halt_clear.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Message-Id: <20170317031743.40128-2-bjsdjshi@linux.vnet.ibm.com>
[CH: Fix typo]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Introduce a trivial, mostly empty <linux/sched/cputime.h> header
to prepare for the moving of cputime functionality out of sched.h.
Update all code that relies on these facilities.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Convert the uses of pr_warning to pr_warn so there are fewer
uses of the old pr_warning.
Miscellanea:
o Align arguments
o Coalesce formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add tracepoints to interrupt handler and core inline assemblies used by
the s390 common I/O layer. These tracepoints can be used to monitor and
validate hardware and hypervisor requests and responses.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is no longer a need to maintain two versions of the same inline
assembly - one with exception handling, and one without - so get rid of
the duplicates and adjust names accordingly. This applies to stsch_err
and msch_err which are now renamed to stsch and msch respectively,
while the original msch function is removed.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The debug_unregister() function performs also input parameter validation.
Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To collect the CPU registers of the crashed system allocated a single
page with memblock_alloc_base and use it as a copy buffer. Replace the
stop-and-store-status sigp with a store-status-at-address sigp in
smp_save_dump_cpus() and smp_store_status(). In both cases the target
CPU is already stopped and store-status-at-address avoids the detour
via the absolute zero page.
For kexec simplify s390_reset_system and call store_status() before
the prefix register of the boot CPU has been set to zero. Use STPX
to store the prefix register and remove dump_prefix_page.
Acked-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow to ipl from CCW based devices residing in any subchannel set.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cio_validate_io_subchannel() and cio_validate_msg_subchannel() are
identical, as the called functions already take care about the
differences between subchannel types.
Just inline the code into the only user,
cio_validate_subchannel(), instead.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove all the casts to and from the machine check interruption code.
This patch changes struct mci to a union, which contains an anonymous
structure with the already known bits and in addition an unsigned
long field, which contains the raw machine check interruption code.
This allows to simply assign and decoce the interruption code value
without the need for all those casts we had all the time.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the 31 bit support in order to reduce maintenance cost and
effectively remove dead code. Since a couple of years there is no
distribution left that comes with a 31 bit kernel.
The 31 bit kernel also has been broken since more than a year before
anybody noticed. In addition I added a removal warning to the kernel
shown at ipl for 5 minutes: a960062e58 ("s390: add 31 bit warning
message") which let everybody know about the plan to remove 31 bit
code. We didn't get any response.
Given that the last 31 bit only machine was introduced in 1999 let's
remove the code.
Anybody with 31 bit user space code can still use the compat mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The multi-threading facility is introduced with the z13 processor family.
This patch adds code to detect the multi-threading facility. With the
facility enabled each core will surface multiple hardware threads to the
system. Each hardware threads looks like a normal CPU to the operating
system with all its registers and properties.
The SCLP interface reports the SMT topology indirectly via the maximum
thread id. Each reported CPU in the result of a read-scp-information
is a core representing a number of hardware threads.
To reflect the reduced CPU capacity if two hardware threads run on a
single core the MT utilization counter set is used to normalize the
raw cputime obtained by the CPU timer deltas. This scaled cputime is
reported via the taskstats interface. The normal /proc/stat numbers
are based on the raw cputime and are not affected by the normalization.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
Move the nohz_delay bit from the s390_idle data structure to the
per-cpu flags. Clear the nohz delay flag in __cpu_disable and
remove the cpu hotplug notifier that used to do this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On systems where a ccw based console device is used a lockdep false alarm
could be triggered when a device driver calls printk while holding a
subchannels lock (e.g. in it's irq handler). Since this is valid behavior
fix this by introducing a separate lock class for the console subchannels
lock.
The lockdep warning was revealed by "printk: enable interrupts before calling
console_trylock_for_printk()" which changed console_unlock() to be called with
lockdep enabled.
[ INFO: possible recursive locking detected ]
3.15.0-rc5-next-20140520 #1 Not tainted
---------------------------------------------
ccwgroup/2239 is trying to acquire lock:
(&(sch->lock)->rlock){-.-...}, at: [<0000000000642a52>] raw3215_write+0x52/0x200
but task is already holding lock:
(&(sch->lock)->rlock){-.-...}, at: [<00000000005fd160>] do_cio_interrupt+0x60/0x108
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(sch->lock)->rlock);
lock(&(sch->lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
8 locks held by ccwgroup/2239:
stack backtrace:
CPU: 3 PID: 2239 Comm: ccwgroup Not tainted 3.15.0-rc5-next-20140520 #1
0000000036fab518 0000000036fab528 0000000000000002 0000000000000000
0000000036fab5b8 0000000036fab530 0000000036fab530 00000000001116e8
0000000000000000 0000000000986ec4 00000000009701b6 000000000000000b
0000000036fab578 0000000036fab518 0000000000000000 0000000000000000
0000000000000000 00000000001116e8 0000000036fab518 0000000036fab578
Call Trace:
([<0000000000111626>] show_trace+0x14e/0x158)
[<000000000011169a>] show_stack+0x6a/0xe8
[<00000000007c6e72>] dump_stack+0x82/0xb0
[<00000000001a95f2>] validate_chain.isra.37+0xa4a/0xbb0
[<00000000001acaca>] __lock_acquire+0x4da/0xcd0
[<00000000001ada1a>] lock_acquire+0xba/0x218
[<00000000007cd634>] _raw_spin_lock_irqsave+0x6c/0xb8
[<0000000000642a52>] raw3215_write+0x52/0x200
[<0000000000643d16>] con3215_write+0x76/0xf8
[<00000000001bd87a>] call_console_drivers.constprop.25+0xfa/0x210
[<00000000001be0b0>] console_unlock+0x3e0/0x4e8
[<00000000001be450>] vprintk_emit+0x298/0x6e0
[<00000000005aa210>] dev_vprintk_emit+0xe0/0x1a8
[<00000000005aa320>] dev_printk_emit+0x48/0x50
[<00000000005aa390>] __dev_printk+0x68/0xb0
[<00000000005aa7c2>] _dev_info+0x62/0x70
[<0000000000657bf0>] qeth_l2_send_setmac_cb+0xd0/0x190
[<0000000000651a1e>] qeth_send_control_data_cb+0x3a6/0x6a8
[<0000000000655546>] qeth_irq+0x1a6/0xac0
[<000000000060a0ac>] ccw_device_call_handler+0xa4/0xc0
[<0000000000608b62>] ccw_device_irq+0x5a/0x190
[<00000000005fd1ca>] do_cio_interrupt+0xca/0x108
[<00000000001c0a2e>] handle_irq_event_percpu+0x5e/0x378
[<00000000001c46fc>] handle_percpu_irq+0x6c/0x98
[<00000000001c0066>] generic_handle_irq+0x46/0x68
[<000000000010b5b6>] do_IRQ+0x5e/0x88
[<00000000007cf304>] io_call+0x6/0x20
[<000000000064c63a>] qeth_send_control_data+0x322/0x570
([<000000000064c50e>] qeth_send_control_data+0x1f6/0x570)
[<0000000000651db2>] qeth_send_ipa_cmd+0x92/0x120
[<000000000065b310>] __qeth_l2_set_online+0x170/0xaa8
[<000000000060ebb6>] ccwgroup_set_online+0x56/0x90
[<000000000060ef96>] ccwgroup_online_store+0xd6/0xe0
[<000000000033d11a>] kernfs_fop_write+0x10a/0x188
[<00000000002bbd00>] vfs_write+0x98/0x1c0
[<00000000002bc8a0>] SyS_write+0x60/0xd0
[<00000000007cee3a>] sysc_nr_ok+0x22/0x28
[<000003fffd0c3f28>] 0x3fffd0c3f28
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the 96-byte irb array from the lowcore and create a per-cpu
variable instead. That way we will pick up any change in the definition
of the struct irb automatically.
Acked-By: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull irq code updates from Thomas Gleixner:
"The irq department proudly presents:
- Another tree wide sweep of irq infrastructure abuse. Clear winner
of the trainwreck engineering contest was:
#include "../../../kernel/irq/settings.h"
- Tree wide update of irq_set_affinity() callbacks which miss a cpu
online check when picking a single cpu out of the affinity mask.
- Tree wide consolidation of interrupt statistics.
- Updates to the threaded interrupt infrastructure to allow explicit
wakeup of the interrupt thread and a variant of synchronize_irq()
which synchronizes only the hard interrupt handler. Both are
needed to replace the homebrewn thread handling in the mmc/sdhci
code.
- New irq chip callbacks to allow proper support for GPIO based irqs.
The GPIO based interrupts need to request/release GPIO resources
from request/free_irq.
- A few new ARM interrupt chips. No revolutionary new hardware, just
differently wreckaged variations of the scheme.
- Small improvments, cleanups and updates all over the place"
I was hoping that that trainwreck engineering contest was a April Fools'
joke. But no.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (68 commits)
irqchip: sun7i/sun6i: Disable NMI before registering the handler
ARM: sun7i/sun6i: dts: Fix IRQ number for sun6i NMI controller
ARM: sun7i/sun6i: irqchip: Update the documentation
ARM: sun7i/sun6i: dts: Add NMI irqchip support
ARM: sun7i/sun6i: irqchip: Add irqchip driver for NMI controller
genirq: Export symbol no_action()
arm: omap: Fix typo in ams-delta-fiq.c
m68k: atari: Fix the last kernel_stat.h fallout
irqchip: sun4i: Simplify sun4i_irq_ack
irqchip: sun4i: Use handle_fasteoi_irq for all interrupts
genirq: procfs: Make smp_affinity values go+r
softirq: Add linux/irq.h to make it compile again
m68k: amiga: Add linux/irq.h to make it compile again
irqchip: sun4i: Don't ack IRQs > 0, fix acking of IRQ 0
irqchip: sun4i: Fix a comment about mask register initialization
irqchip: sun4i: Fix irq 0 not working
genirq: Add a new IRQCHIP_EOI_THREADED flag
genirq: Document IRQCHIP_ONESHOT_SAFE flag
ARM: sunxi: dt: Convert to the new irq controller compatibles
irqchip: sunxi: Change compatibles
...
Pull timer updates from Ingo Molnar:
"The main purpose is to fix a full dynticks bug related to
virtualization, where steal time accounting appears to be zero in
/proc/stat even after a few seconds of competing guests running busy
loops in a same host CPU. It's not a regression though as it was
there since the beginning.
The other commits are preparatory work to fix the bug and various
cleanups"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arch: Remove stub cputime.h headers
sched: Remove needless round trip nsecs <-> tick conversion of steal time
cputime: Fix jiffies based cputime assumption on steal accounting
cputime: Bring cputime -> nsecs conversion
cputime: Default implementation of nsecs -> cputime conversion
cputime: Fix nsecs_to_cputime() return type cast
The architectures that override cputime_t (s390, ppc) don't provide
any version of nsecs_to_cputime(). Indeed this cputime_t implementation
by backend only happens when CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y under
which the core code doesn't make any use of nsecs_to_cputime().
At least for now.
We are going to make a broader use of it so lets provide a default
version with a per usecs granularity. It should be good enough for most
usecases.
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
commit: 8f945a33 (genirq: Move kstat_incr_irqs_this_cpu() to core)
unearthed the following:
arch/s390/kernel/irq.c: In function 'init_IRQ':
>> arch/s390/kernel/irq.c:93:2: error: implicit declaration of function 'irq_reserve_irqs'
[-Werror=implicit-function-declaration]
....
cc1: some warnings being treated as errors
--
drivers/s390/cio/cio.c: In function 'init_cio_interrupts':
>> drivers/s390/cio/cio.c:594:2: error: implicit declaration of function
'irq_set_chip_and_handler' [-Werror=implicit-function-declaration]
[-Werror=implicit-function-declaration]
....
cc1: some warnings being treated as errors
The reason is that those files require linux/irq.h and magically
pulled that in via linux/kernel_stat.h
The commit above got rid of the pointless include of linux/irq.h in
linux/kernel_stat.h and therefor broke the build.
Include linux/irq.h
Reported-by: fengguang.wu@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: s390 <linux-s390@vger.kernel.org>
Let the core do the irq_desc resolution.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: s390 <linux-s390@vger.kernel.org>
Link: http://lkml.kernel.org/r/20140223212737.983433636@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The maximum usable buffer size of the s390 debug feature (when using
the sprintf_view) is 11 * sizeof(long) (1 pointer for the format
string + 10 arguments). When a larger buffer size is specified the
additional memory is unused and wasted per debug entry. So reducing
the buffer size to its maximum (or to the actual buffer size used)
will make more precious debug feature space usable.
For pci_msg, chsc_msg, and cio_crw we use the additional usable dbf
space to reduce the number of allocated pages.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The modify subchannel wrapper cio_commit_config can fail when
(unexpected) status is pending on the subchannel.
Callers of cio_commit_config (that operated on enabled subchannels)
needed to do error handling for that case (clear the unexpected
status with test subchannel and retry). This error handling is
missing in some code paths and caused online setting of devices to
fail.
Fix this for all callers by moving the error handling inside
cio_commit_config.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The result of the store-clock-fast (STCKF) instruction is a bit fuzzy.
It can happen that the value stored on one CPU is smaller than the value
stored on another CPU, although the order of the stores is the other
way around. This can cause deltas of get_tod_clock() values to become
negative when they should not be.
We need to be more careful with store-clock-fast, this patch partially
reverts git commit e4b7b4238e666682555461fa52eecd74652f36bb "time:
always use stckf instead of stck if available". The get_tod_clock()
function now uses the store-clock-extended (STCKE) instruction.
get_tod_clock_fast() can be used if the fuzziness of store-clock-fast
is acceptable e.g. for wait loops local to a CPU.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With the introduction of PCI it became apparent that s390 should
convert to generic hardirqs as too many drivers do not have the
correct dependency for GENERIC_HARDIRQS. On the architecture
level s390 does not have irq lines. It has external interrupts,
I/O interrupts and adapter interrupts. This patch hard-codes all
external interrupts as irq #1, all I/O interrupts as irq #2 and
all adapter interrupts as irq #3. The additional information from
the lowcore associated with the interrupt is stored in the
pt_regs of the interrupt frame, where the interrupt handler can
pick it up. For PCI/MSI interrupts the adapter interrupt handler
scans the relevant bit fields and calls generic_handle_irq with
the virtual irq number for the MSI interrupt.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Copy the interrupt parameters from the lowcore to the pt_regs structure
in entry[64].S and reduce the arguments of the low level interrupt handler
to the pt_regs pointer only. In addition move the test-pending-interrupt
loop from do_IRQ to entry[64].S to make sure that interrupt information
is always delivered via pt_regs.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When we fetch an interrupt on the CCW console using tsch (via
ccw_device_wait_idle formerly known as wait_cons_dev) we increment
the irq count for the affected interruption class but it is not
accounted as an IO interrupt.
This is broken since commit b603d258a4
"s390: remove superfluous tpi from wait_cons_dev"
Fix it so that the sum of the individual interrupts per class matches
the number of IO interrupts again.
Reported-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cio_validate_subchannel is used to do some basic checks to find out
if it's worth to further investigate a subchannel. Move the allocation
and initialization of the subchannels locks to css_alloc_subchannel.
Clean up the functions involved while at it.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use cio_register_early_subchannels to register early subchannels
which are already in use. Call this function before we do the
actual subchannel scanning loop. This helps us to get rid of some
more special cases regarding the console subchannel.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the static console subchannel (and friends) and use dynamic
allocation for these structures. With this change the console
subchanel is treated (mostly) like any other subchannel and we can
remove some special cases.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
wait_cons_dev is used to busy wait for an interrupt on the console
ccw device. Stop using the static console_subchannel and add a
parameter to this function to specify on which ccw device/subchannel
we have to do the polling.
While at it rename the function to ccw_device_wait_idle and
move it to device.c
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix name clash with some common code device drivers and add "tod"
to all tod clock access function names.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that irq sum accounting for /proc/stat's "intr" line works again we
have the oddity that the sum field (first field) contains only the sum
of the second (external irqs) and third field (I/O interrupts).
The reason for that is that these two fields are already sums of all other
fields. So if we would sum up everything we would count every interrupt
twice.
This is broken since the split interrupt accounting was merged two years
ago: 052ff461c8 "[S390] irq: have detailed
statistics for interrupt types".
To fix this remove the split interrupt fields from /proc/stat's "intr"
line again and only have them in /proc/interrupts.
This restores the old behaviour, seems to be the only sane fix and mimics
a behaviour from other architectures where /proc/interrupts also contains
more than /proc/stat's "intr" line does.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For more than two years, since f2c66cd8ee
"/proc/stat: scalability of irq num per cpu" the output of /proc/stat is
broken.
The first field in the "intr" line should contain the sum of all interrupts,
however since the above mentioned change it is always zero.
The reason for that is that a per cpu irq sum variable had been introduced
which got incremented when calling kstat_incr_irqs_this_cpu(). However
on s390 we directly incremented only the per cpu per irq counter by accessing
the array element via kstat_cpu(smp_processor_id()).irqs[...].
So fix this and use the kstat_incr_irqs_this_cpu() wrapper which increments
both: the per cpu per irq counter and the per cpu irq sum counter.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of these:
arch/s390/kernel/smp.c:134:19: warning: ‘status’ may be used uninitialized in this function [-Wuninitialized]
arch/s390/mm/pgtable.c:641:10: warning: ‘table’ may be used uninitialized in this function [-Wuninitialized]
arch/s390/mm/pgtable.c:644:12: warning: ‘page’ may be used uninitialized in this function [-Wuninitialized]
drivers/s390/cio/cio.c:1037:14: warning: ‘schid’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
wait_cons_dev waits for a particular subchannel to complete an I/O.
It is not necessary to use tpi to get the subchannel id as it is
already known. This avoids changes to the interrupt subclass mask
and allows to remove the lock & unlock of the subchannel lock.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Whenever the cpu loads an enabled wait PSW it will appear as idle to the
underlying host system. The code in default_idle calls vtime_stop_cpu
which does the necessary voodoo to get the cpu time accounting right.
The udelay code just loads an enabled wait PSW. To correct this rework
the vtime_stop_cpu/vtime_start_cpu logic and move the difficult parts
to entry[64].S, vtime_stop_cpu can now be called from anywhere and
vtime_start_cpu is gone. The correction of the cpu time during wakeup
from an enabled wait PSW is done with a critical section in entry[64].S.
As vtime_start_cpu is gone, s390_idle_check can be removed as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch provides the architecture specific part of the s390 kdump
support.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Current IRQ statistics support does not show detail counts for I/O
interrupts which are processed internally only. The result is a
summation count which is way off such as this one:
CPU0 CPU1 CPU2
I/O: 1331 710 442
[...]
QAI: 15 16 16 [I/O] QDIO Adapter Interrupt
QDI: 1 0 0 [I/O] QDIO Interrupt
DAS: 706 645 381 [I/O] DASD
C15: 26 10 0 [I/O] 3215
C70: 0 0 0 [I/O] 3270
TAP: 0 0 0 [I/O] Tape
VMR: 0 0 0 [I/O] Unit Record Devices
LCS: 0 0 0 [I/O] LCS
CLW: 0 0 0 [I/O] CLAW
CTC: 0 0 0 [I/O] CTC
APB: 0 0 0 [I/O] AP Bus
Fix this by moving I/O interrupt accounting into the common I/O layer.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
