Since the USB notifier context is atomic, we can not start or stop charging
in atomic context. Thus this patch adds one work to help to charge or
discharge.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove at91_ramc_of_match[] since it is not used anywhere in this code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use only one poweroff function and adapt it to work for both scenarios
(with LPDDR or not). The assignement of pm_power_off was moved at the
end of probe after all initializations are OK. This patch adapt the idea
from commit 4e018c1e9b ("power: reset: at91-poweroff: use only one
poweroff function").
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq24196 is another variant of the bq24190 charger ic.
Its register set is identical to the bq24192 and it even reuses
the same part number (0x5).
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add extcon support so that we can notify USB drivers of cable state
changes. Based on work from Jonathan Marek. USB OTG was tested on a LG
Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds an of_match for the usb-otg-vbus regulator to
bq24190_charger.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds support for the bq24192 variant to bq24190_charger.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: Changed if statement to a switch based on
feedback from Sebastian Reichel.]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Switch the SI to boot mode so on a warm reboot, the SI is able to access
the flash.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Similar to gpio-reset allow to specify active and inactive delays
while keeping the 100ms defaults that were used previously all the time.
The dt-properties are named the same as in gpio-reset but get an "-ms"
suffix as properties should contain such a suffix specifying its unit.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Trivial fix to clean up indentation issue, remove an extraneous tab
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
changes related to axp813.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=FoKv
-----END PGP SIGNATURE-----
Merge tag 'psy-mfd-axp813-immutable-for-v4.21-signed' into psy-next
Immutable branch between mfd and power-supply for driver
changes related to axp813.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
AXP813 and AXP803 PMICs can control input current and minimum voltage.
Both of these values are configurable.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make use of the recommended BIT() macro for bit defines.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The axp20x_usb_power driver uses BIT() operations but lacks the include
for it. Include the bitops.h header file.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Don't populate the array cpcap_battery_irqs on the stack but instead
make it static. Makes the object code smaller by 99 bytes:
Before:
text data bss dec hex filename
13673 2448 0 16121 3ef9 cpcap-battery.o
After:
text data bss dec hex filename
13510 2512 0 16022 3e96 cpcap-battery.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
According to [1] and [2], the temperature values are in tenths of degree
Celsius. Exposing the Celsius value makes the battery appear on fire:
$ upower -i /org/freedesktop/UPower/devices/battery_olpc_battery
...
temperature: 236.9 degrees C
Tested on OLPC XO-1 and OLPC XO-1.75 laptops.
[1] include/linux/power_supply.h
[2] Documentation/power/power_supply_class.txt
Fixes: fb972873a7 ("[BATTERY] One Laptop Per Child power/battery driver")
Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix build errors when FUEL_GUAGE_SC27XX is enabled but IIO is either
not enabled or IIO=m and FUEL_GUAGE_SC27XX=y.
ld: drivers/power/supply/sc27xx_fuel_gauge.o: in function `sc27xx_fgu_get_temp':
sc27xx_fuel_gauge.c:(.text+0x1d2): undefined reference to `iio_read_channel_processed'
ld: drivers/power/supply/sc27xx_fuel_gauge.o: in function `sc27xx_fgu_probe':
sc27xx_fuel_gauge.c:(.text+0x97f): undefined reference to `devm_iio_channel_get'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-pm@vger.kernel.org
Acked-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds the Spreadtrum SC27XX serial PMICs fuel gauge support,
which is used to calculate the battery capacity.
Original-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We have introduced some battery properties to present the OCV table
temperatures and OCV capacity table values. Thus this patch add OCV
temperature and OCV table for battery information, as well as providing
some helper functions to use the OCV capacity table for users.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add one field for 'struct power_supply_battery_info' to present the battery
factory internal resistance.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----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=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
Use the new of_get_compatible_child() helper to lookup the usb sibling
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(non-sibling) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the parent device node).
While at it, also fix the related phy-node reference leak.
Fixes: f5e4edb8c8 ("power: twl4030_charger: find associated phy by more reliable means.")
Cc: stable <stable@vger.kernel.org> # 4.2
Cc: NeilBrown <neilb@suse.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 201510 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Trivial fix to spelling mistake in MODULE_DESCRIPTION text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
omap_sr_register_pmic() was introduced in 2010 in commit
984aa6dbf4 ("OMAP3: PM: Adding smartreflex driver support.")
. There was never any caller of this function in mainline resulting in a
warning
sr_init: No PMIC hook to init smartreflex
for each machine where this driver is enabled. So remove the unused
function and the pr_warn.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the binding and driver for pms405 pon.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
According to the datasheet, bq27411 is similar to bq27421.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds the SC2731 PMIC switch charger support.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This avoids getting woken up from suspend after power interruptions
when the bci wrongly thinks the battery is full just because
of input current going low because of low input power
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
the charging current uses unsigned int variables, if we step back
if the current is still low, we would run into negative which
means setting the target to a huge value.
Better add checks here.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f1 ("mfd: max8998: Add support for Device Tree")
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Immutable branch between mfd and power-supply for driver
changes in CROS USBPD charger driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=ya3t
-----END PGP SIGNATURE-----
Merge tag 'psy-mfd-cros-immutable-for-v4.20-signed' into psy-next
Immutable branch for mfd and power-supply for v4.20
Immutable branch between mfd and power-supply for driver
changes in CROS USBPD charger driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
ChromeOS devices can have one optional dedicated port.
The Dedicated port is unique and similar to the USB PD ports
except that it doesn't support as many properties.
The presence of a dedicated port is determined from whether the
EC's charger port count is equal to 'number of USB PD port' + 1.
The dedicated port ID is always the last valid port ID.
This commit keeps compatibility with Embedded Controllers that do not
support the new EC_CMD_CHARGE_PORT_COUNT command by setting
the number of charger port to be equal to the number of USB PD port
when this command fails.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Immutable branch between mach-at91 and power-supply for driver
changes in at91-poweroff.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=n/Lz
-----END PGP SIGNATURE-----
Merge tag 'psy-at91-poweroff-immutable-for-v4.20-signed' into psy-next
Immutable branch for mach-at91 and power-supply for v4.20
Immutable branch between mach-at91 and power-supply for driver
changes in at91-poweroff.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There should be only one instance of struct shdwc in the system. This is
referenced through at91_shdwc. Return in probe if at91_shdwc is already
allocated.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Rename at91_shdwc_base member of struct shdwc to shdwc_base. There is
already an "at91" string in at91_shdwc object.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make sclk part of struct shdwc to have all the data specific to SHDWC
grouped together in one structure.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make mpddrc_base part of struct shdwc since there is also only one
instance of struct shdwc *at91_shdwc in system and to have all data
specific to SHDWC grouped together.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use only one poweroff function for sama5d2 and adapt it to work for both
scenarios (having LPDDR or not).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The SAMA5D2 NRST input signal is resynchronized with the SLCK clock and it
can take up to 2 SLCK cycles (about 90us) for the internal reset to be
effective. During this delay, the VDDCORE current consumption may still be
high (application-dependent) with the VDDCORE regulator already OFF. Under
such conditions, VDDCORE may operate below its operating range leading to
potential register corruption.
To prevent such situation, it is recommended to decrease significantly the
power consumption of the device once the voltage regulator is turned-off.
This can be achieved by operating the device at a much lower low frequency.
To solve this switch the master clock to slock clock just before writing
shutdown command to shutdown controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Suggested-by: Patrice Vilchez <patrice.vilchez@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If kstrtoul() fails then we print "charge_full" when it's uninitialized.
The debug printk doesn't add anything so I deleted it and cleaned these
two functions up a bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This adds rate limiting to the message that is printed when reading a
power supply property via sysfs returns an error. This will prevent
userspace applications from unintentionally dDOSing the system by
continuously reading a property that returns an error.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BQ2589x family has the capability of reading the current battery voltage.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BQ25896 is almost identical to the BQ25890.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are a few table entries that aren't used. Drop them.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
To ease adding a new part variant some debugging is handy.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Replace GPL v2.0 and v2.0+ license statements with SPDX license
identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
simple_strtoul is obsolete, and use kstrtoint instead
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pointer 'dev' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Almost all files in the kernel are either plain text or UTF-8 encoded. A
couple however are ISO_8859-1, usually just a few characters in a C
comments, for historic reasons.
This converts them all to UTF-8 for consistency.
Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms@verge.net.au> [IPVS portion]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> [IIO]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The URL of bq27441-g1 and bq27426 are missing and bq27520-g4 is duplicated.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
It seems that a *break* is missing in order to avoid a fall-through.
Otherwise, the calculation of *data* makes no sense.
Addresses-Coverity-ID: 1271172 ("Missing break in switch")
Fixes: 87c2d90678 ("power: max77693: Add charger driver for Maxim 77693")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1394724 ("Missing break in switch")
Addresses-Coverity-ID: 114958 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This fixes the value that accounts for the Vce of a transistor in the
LEGO MINDSTORMS EV3 power supply driver. The old value (200mV) was the
max value from the data sheet. After testing, the actual value has been
found to be 50mV. By using 50mV we get a more accurate voltage
indication.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This changes the LEGO MINDSTORMS EV3 power supply driver to return an
error if iio_read_channel_processed() fails.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add a matching table for devicetree probing, and optionally set the module
parameter variables from DT properties.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This patch removes the w1 slave driver that used to register the w1 family
and instanciate a platform device at runtime. The code now lives in the
supply driver instead to avoid that level of indirection.
The old device name "ds2760-battery.0" is preserved, so userspace
applications can access the same virtual device nodes as before.
Note that because the w1 core does not currently have a framework for
suspend/resume, the driver now registers a PM notifier callback.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We end up reading one element beyond the end of the adp5061_vmax[] array
here.
Fixes: fe8e81b7e8 ("adp5061: New driver for ADP5061 I2C battery charger")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds basic support for Analog Devices I2C programmable linear
battery charger.
With this driver, some parameters can be read and configured such as:
* trickle charge current level (PRECHARGE_CURRENT)
* trickle charge voltage threshold (VOLTAGE_MIN)
* weak charge threshold (VOLTAGE_AVG)
* constant current (CONSTANT_CHARGE_CURRENT)
* constant charge voltage limit (CONSTANT_CHARGE_VOLTAGE_MAX)
* battery full (CAPACITY_LEVEL)
* input current limit (INPUT_CURRENT_LIMIT)
* charger status (STATUS)
* battery status (CAPACITY_LEVEL)
* termination current (CHARGE_TERM_CURRENT)
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADP5061.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
If an iio channel defines a basic property, there are duplicate entries
in /sys/class/power/*/uevent.
So add a check to avoid duplicates. Since all channels may be duplicates,
we have to modify the related error check.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We did have sporadic problems in the pinctrl framework during boot
where a pin group name unexpectedly became NULL leading to a NULL
dereference in strcmp.
Detailled analysis of the failing cases did reveal that there were
two devm allocated objects close to each other. The second one was
the affected group_desc in pinmux and the first one was the
psy_desc->properties buffer of the gab driver.
Review of the gab code showed that the address calculation for
one memcpy() is wrong. It does
properties + sizeof(type) * index
but C is defined to do the index multiplication already for
pointer + integer additions. Hence the factor was applied twice
and the memcpy() does write outside of the properties buffer.
Sometimes it happened to be the pinctrl and triggered the strcmp(NULL).
Anyways, it is overkill to use a memcpy() here instead of a simple
assignment, which is easier to read and has less risk for wrong
address calculations. So we change code to a simple assignment.
If we initialize the index to the first free location, we can even
remove the local variable 'properties'.
This bug seems to exist right from the beginning in 3.7-rc1 in
commit e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We should look at val which contains the value read from the register,
not ret which is always 0 on a successful read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: eac53b3664 ("power: supply: axp288_charger: Drop platform_data dependency")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
getnstimeofday64() is deprecated in favor of the ktime_get() family.
The direct replacement would be ktime_get_real_ts64(), but we only need
the seconds value, and it seems better to use boottime than real time
to avoid unexpected behavior with a concurrent settimeofday().
ktime_get_seconds() might also work, but it seems better to use
boottime than monotonic time since I assume that the charging
process continues during suspend.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Even after the previous fix I have experienced more spurious
poweroffs on the gemini SoC. After this fix it finally seems
to go away.
Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Vexpress platforms provide two different restart handlers: SYS_REBOOT
that restart the entire system, while DB_RESET only restarts the
daughter board containing the CPU. DB_RESET is overridden by SYS_REBOOT
if it exists.
notifier_chain_register used in register_restart_handler by design
relies on notifiers to be registered once only, however vexpress restart
notifier can get registered twice. When this happen it corrupts list
of notifiers, as result some notifiers can be not called on proper
event, traverse on list can be cycled forever, and second unregister
can access already freed memory.
So far, since this was the only restart handler in the system, no issue
was observed even if the same notifier was registered twice. However
commit 6c5c0d48b6 ("watchdog: sp805: add restart handler") added
support for SP805 restart handlers and since the system under test
contains two vexpress restart and two SP805 watchdog instances, it was
observed that during the boot traversing the restart handler list looped
forever as there's a cycle in that list resulting in boot hang.
This patch fixes the issues by ensuring that the notifier is installed
only once.
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: 46c99ac662 ("power/reset: vexpress: Register with kernel restart handler")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver gets various bits of information about what is connected to
USB PD ports from the EC and converts that into power_supply properties.
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Trivial fix to spelling mistake in dev_warn message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
zx_reboot_probe() increments refcnt of zx296702-pcu device node by
of_find_compatible_node() and leaves it undecremented on both
successful and error paths.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver was originally submitted for the TI BQ20Z75 battery IC
(commit a7640bfa10 ("power_supply: Add driver for TI BQ20Z75 gas gauge
IC")) and later renamed to express generic SBS support. While it's
mostly true that this driver implemented a standard SBS command set, it
takes liberties with the REG_MANUFACTURER_DATA register. This register
is specified in the SBS spec, but it doesn't make any mention of what
its actual contents are.
We've sort of noticed this optionality previously, with commit
17c6d3979e ("sbs-battery: make writes to ManufacturerAccess
optional"), where we found that some batteries NAK writes to this
register.
What this really means is that so far, we've just been lucky that most
batteries have either been compatible with the TI chip, or else at least
haven't reported highly-unexpected values.
For instance, one battery I have here seems to report either 0x0000 or
0x0100 to the MANUFACTURER_ACCESS_STATUS command -- while this seems to
match either Wake Up (bits[11:8] = 0000b) or Normal Discharge
(bits[11:8] = 0001b) status for the TI part [1], they don't seem to
actually correspond to real states (for instance, I never see 0101b =
Charge, even when charging).
On other batteries, I'm getting apparently random data in return, which
means that occasionally, we interpret this as "battery not present" or
"battery is not healthy".
All in all, it seems to be a really bad idea to make assumptions about
REG_MANUFACTURER_DATA, unless we already know what battery we're using.
Therefore, this patch reimplements the "present" and "health" checks to
the following on most SBS batteries:
1. HEALTH: report "unknown" -- I couldn't find a standard SBS command
that gives us much useful here
2. PRESENT: just send a REG_STATUS command; if it succeeds, then the
battery is present
Also, we stop sending MANUFACTURER_ACCESS_SLEEP to non-TI parts. I have
no proof that this is useful and supported.
If someone explicitly provided a 'ti,bq20z75' compatible property, then
we continue to use the existing TI command behaviors, and we effectively
revert commit 17c6d3979e ("sbs-battery: make writes to
ManufacturerAccess optional") to again make these commands required.
[1] http://www.ti.com/lit/er/sluu265a/sluu265a.pdf
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
* bq27xxx: Add BQ27426 support
* ab8500: Drop AB8540/9540 support
* Introduced new usb_type property
* Properly document the power-supply ABI
* misc. cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=UB16
-----END PGP SIGNATURE-----
Merge tag 'for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- bq27xxx: Add BQ27426 support
- ab8500: Drop AB8540/9540 support
- Introduced new usb_type property
- Properly document the power-supply ABI
- misc. cleanups and fixes
* tag 'for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
MAINTAINERS: add entry for LEGO MINDSTORMS EV3
power: supply: ab8500_charger: fix spelling mistake: "faile" -> "failed"
power: supply: axp288_fuel_gauge: Remove polling from the driver
power: supply: axp288_fuelguage: Do not bind when the fg function is not used
power: supply: axp288_charger: Do not bind when the charge function is not used
power: supply: axp288_charger: Support 3500 and 4000 mA input current limit
power: supply: s3c-adc-battery: fix driver data initialization
power: supply: charger-manager: Verify polling interval only when polling requested
power: supply: sysfs: Use enum to specify property
power: supply: ab8500: Drop AB8540/9540 support
power: supply: ab8500_fg: fix spelling mistake: "Disharge" -> "Discharge"
power: supply: simplify getting .drvdata
power: supply: bq27xxx: Add support for BQ27426
gpio-poweroff: Use gpiod_set_value_cansleep
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
To allow users of the power supply framework to be hw description
agnostic, this commit adds the ability to pass a fwnode pointer,
via the power_supply_config structure, to the initialisation code
of the core, instead of explicitly specifying of_ndoe. If that
fwnode pointer is provided then it will automatically resolve down
to of_node on platforms which support it, otherwise it will be NULL.
In the future, when ACPI support is added, this can be modified to
accommodate ACPI without the need to change calling code which
already provides the fwnode handle in this manner.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary data for handling io voltage domains on PX30.
As interesting tidbit, the PX30 contains two separate iodomain areas.
One in the regular General Register Files (GRF) and one in PMUGRF in the
pmu power domain.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
trivial fix to spelling mistake in dev_error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This is a signed tag/merge point to handle the cross-tree merge of the
USB and power supply subsystems for the patch series:
Subject: [PATCH v8 0/6] typec: tcpm: Add sink side support for PPS
It is based on the usb.git tree, in the usb-next branch, for merging in
4.18-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWuGASg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylqPACcDdrowGIQp0vVa7VrOJNMy9pL5K0An1cjnaUt
0sXkKK8YWC3EQSSYtr3Q
=McRU
-----END PGP SIGNATURE-----
Merge tag 'tags/tcpm-pps-4.18' into psy-next
Tag/Merge point for adding typeC power supply support
This is a signed tag/merge point to handle the cross-tree merge of the
USB and power supply subsystems for the patch series:
Subject: [PATCH v8 0/6] typec: tcpm: Add sink side support for PPS
It is based on the usb.git tree, in the usb-next branch, for merging in
4.18-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Userspace class/power_supply consumers such as upower, already know some
supplies need to be polled to get up2date info. Doing this in the kernel
and then waking up userspace just causes unnecessary wakeups and i2c
transfers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some devices with an AXP288 PMIC do not have a battery at all, or use
external charger and fuelgauge ICs instead of the AXP288 builtin
functionality.
On such devices we should not bind to the fuelgauge function to avoid
exporting a non working power_supply class device.
This also avoids the following errors repeating over and over again in
dmesg:
axp288_fuel_gauge axp288_fuel_gauge: capacity measurement not valid
axp288_fuel_gauge axp288_fuel_gauge: Error 0xe2 contents not valid
power_supply axp288_fuel_gauge: driver failed to report 'charge_now'
property: -6
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some devices with an AXP288 PMIC do not have a battery at all, or use
external charger and fuelgauge ICs instead of the AXP288 builtin
functionality.
On such devices we should not bind to the charge function to avoid
exporting a non working power_supply class device.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The AXP288 supports an input-current-limit of up to 4000 mA, this
commit adds support for the 3500 and 4000 mA settings which were
missing until now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
For power_supply_get_drvdata() routine to work correctly the driver data
has to be provided when registering power supply, otherwise driver gives up
immediately with these errors:
power_supply main-battery: no battery infos ?!
power_supply main-battery: driver failed to report `status' property: -22
Signed-off-by: Sergiy Kibrik <sakib@darkstar.site>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Driver bails out with -EINVAL when no polling specififaion is requested.
Fix that by verifing polling interval only if polling_mode is different
from CM_POLL_DISABLE.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Power supply property is in fact enum, so reflect it in code.
Also use switch statement in show property function as is done
for storing property.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Trivial fix to spelling mistake in dev_dbg message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
