On a dual controller setup with multipath enabled, some MEDIUM ERRORs
caused both paths to be failed, thus I/O got queued/blocked since the
'queue_if_no_path' feature is enabled by default on IPR controllers.
This example disabled 'queue_if_no_path' so the I/O failure is seen at
the sg_dd program. Notice that after the sg_dd test-case, both paths
are in 'failed' state, and both path/priority groups are in 'enabled'
state (not 'active') -- which would block I/O with 'queue_if_no_path'.
# sg_dd if=/dev/dm-2 bs=4096 count=1 dio=1 verbose=4 blk_sgio=0
<...>
read(unix): count=4096, res=-1
sg_dd: reading, skip=0 : Input/output error
<...>
# dmesg
[...] sd 2:2:16:0: [sds] FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[...] sd 2:2:16:0: [sds] Sense Key : Medium Error [current]
[...] sd 2:2:16:0: [sds] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] sd 2:2:16:0: [sds] CDB: Read(10) 28 00 00 00 00 00 00 00 20 00
[...] blk_update_request: I/O error, dev sds, sector 0
[...] device-mapper: multipath: Failing path 65:32.
<...>
[...] device-mapper: multipath: Failing path 65:224.
# multipath -l
1IBM_IPR-0_59C2AE0000001F80 dm-2 IBM ,IPR-0 59C2AE00
size=5.2T features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=0 status=enabled
| `- 2:2:16:0 sds 65:32 failed undef running
`-+- policy='service-time 0' prio=0 status=enabled
`- 1:2:7:0 sdae 65:224 failed undef running
This is not the desired behavior. The dm-multipath explicitly checks
for the MEDIUM ERROR case (and a few others) so not to fail the path
(e.g., I/O to other sectors could potentially happen without problems).
See dm-mpath.c :: do_end_io_bio() -> noretry_error() !->! fail_path().
The problem trace is:
1) ipr_scsi_done() // SENSE KEY/CHECK CONDITION detected, go to..
2) ipr_erp_start() // ipr_is_gscsi() and masked_ioasc OK, go to..
3) ipr_gen_sense() // masked_ioasc is IPR_IOASC_MED_DO_NOT_REALLOC,
// so set DID_PASSTHROUGH.
4) scsi_decide_disposition() // check for DID_PASSTHROUGH and return
// early on, faking a DID_OK.. *instead*
// of reaching scsi_check_sense().
// Had it reached the latter, that would
// set host_byte to DID_MEDIUM_ERROR.
5) scsi_finish_command()
6) scsi_io_completion()
7) __scsi_error_from_host_byte() // That would be converted to -ENODATA
<...>
8) dm_softirq_done()
9) multipath_end_io()
10) do_end_io()
11) noretry_error() // And that is checked in dm-mpath :: noretry_error()
// which would cause fail_path() not to be called.
With this patch applied, the I/O is failed but the paths are not. This
multipath device continues accepting more I/O requests without blocking.
(and notice the different host byte/driver byte handling per SCSI layer).
# dmesg
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 40 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 10 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] Buffer I/O error on dev dm-6, logical block 0, async page read
# multipath -l 1IBM_IPR-0_59C2AE0000001F80
1IBM_IPR-0_59C2AE0000001F80 dm-6 IBM ,IPR-0 59C2AE00
size=5.2T features='1 queue_if_no_path' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=0 status=active
| `- 2:2:7:0 sdaf 65:240 active undef running
`-+- policy='service-time 0' prio=0 status=enabled
`- 1:2:7:0 sdh 8:112 active undef running
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Directly call ELS request handler functions in fc_lport_recv_els_req
instead of saving the pointer to the handler's receive function and then
later dereferencing this pointer.
This makes the code a bit more obvious.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sg_remove_sfp_usercontext() is clearing any sg requests, but needs to
take 'rq_list_lock' when modifying the list.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'Sg_request' is using a private list implementation; convert it to
standard lists.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check for a valid direction before starting the request, otherwise we
risk running into an assertion in the scsi midlayer checking for valid
requests.
[mkp: fixed typo]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Link: http://www.spinics.net/lists/linux-scsi/msg104400.html
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 'reserved' page array is used as a short-cut for mapping data,
saving us to allocate pages per request. However, the 'reserved' array
is only capable of holding one request, so this patch introduces a mutex
for protect 'sg_fd' against concurrent accesses.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unused.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ioctl SET_FORCE_LOW_DMA has never worked since the initial git
check-in, and the respective setting is nowadays handled correctly. So
disable it entirely.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During a PCI error recovery, if aac_check_health() is not aware that a
PCI error happened and we have an offline PCI channel, it might trigger
some errors (like NULL pointer dereference) and inhibit the error
recovery process to complete.
This patch makes the health check procedure aware of PCI channel issues,
and in case of error recovery process, the function
aac_adapter_check_health() returns -1 and let the recovery process to
complete successfully. This patch was tested on upstream kernel
v4.11-rc5 in PowerPC ppc64le architecture with adapter 9005:028d
(VID:DID) - the error recovery procedure was able to recover fine.
Fixes: 5c63f7f710 ("aacraid: Added EEH support")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several local or function parameter pointers that are being
assigned NULL after a kfree where and these have no effect and hence can
be removed.
Fixes various cppcheck warnings:
"Assignment of function parameter has no effect outside the
function. Did you forget dereferencing it"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is not safe for one thread to modify the ->flags
of another thread as there is no locking that can protect
the update.
So tsk_restore_flags(), which takes a task pointer and modifies
the flags, is an invitation to do the wrong thing.
All current users pass "current" as the task, so no developers have
accepted that invitation. It would be best to ensure it remains
that way.
So rename tsk_restore_flags() to current_restore_flags() and don't
pass in a task_struct pointer. Always operate on current->flags.
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull block fixes from Jens Axboe:
"Here's a pull request for 4.11-rc, fixing a set of issues mostly
centered around the new scheduling framework. These have been brewing
for a while, but split up into what we absolutely need in 4.11, and
what we can defer until 4.12. These are well tested, on both single
queue and multiqueue setups, and with and without shared tags. They
fix several hangs that have happened in testing.
This is obviously larger than I would have preferred at this point in
time, but I don't think we can shave much off this and still get the
desired results.
In detail, this pull request contains:
- a set of five fixes for NVMe, mostly from Christoph and one from
Roland.
- a series from Bart, fixing issues with dm-mq and SCSI shared tags
and scheduling. Note that one of those patches commit messages may
read like an optimization, but it is in fact an important fix for
queue restarts in particular.
- a series from Omar, most importantly fixing a hang with multiple
hardware queues when we fail to get a driver tag. Another important
fix in there is for resizing hardware queues, which nbd does when
handling multiple sockets for one connection.
- fixing an imbalance in putting the ctx for hctx request allocations
from Minchan"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: Restart a single queue if tag sets are shared
dm rq: Avoid that request processing stalls sporadically
scsi: Avoid that SCSI queues get stuck
blk-mq: Introduce blk_mq_delay_run_hw_queue()
blk-mq: remap queues when adding/removing hardware queues
blk-mq-sched: fix crash in switch error path
blk-mq-sched: set up scheduler tags when bringing up new queues
blk-mq-sched: refactor scheduler initialization
blk-mq: use the right hctx when getting a driver tag fails
nvmet: fix byte swap in nvmet_parse_io_cmd
nvmet: fix byte swap in nvmet_execute_write_zeroes
nvmet: add missing byte swap in nvmet_get_smart_log
nvme: add missing byte swap in nvme_setup_discard
nvme: Correct NVMF enum values to match NVMe-oF rev 1.0
block: do not put mq context in blk_mq_alloc_request_hctx
Separating discards and zeroout operations allows us to remove the LBPRZ
block zeroing constraints from discards and honor the device preferences
for UNMAP commands.
If supported by the device, we'll also choose UNMAP over one of the
WRITE SAME variants for discards.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that zeroout and discards are distinct operations we need to
separate the policy of choosing the appropriate command. Create a
zeroing_mode which can be one of:
write: Zeroout assist not present, use regular WRITE
writesame: Allow WRITE SAME(10/16) with a zeroed payload
writesame_16_unmap: Allow WRITE SAME(16) with UNMAP
writesame_10_unmap: Allow WRITE SAME(10) with UNMAP
The last two are conditional on the device being thin provisioned with
LBPRZ=1 and LBPWS=1 or LBPWS10=1 respectively.
Whether to set the UNMAP bit or not depends on the REQ_NOUNMAP flag. And
if none of the _unmap variants are supported, regular WRITE SAME will be
used if the device supports it.
The zeroout_mode is exported in sysfs and the detected mode for a given
device can be overridden using the string constants above.
With this change in place we can now issue WRITE SAME(16) with UNMAP set
for block zeroing applications that require hard guarantees and
logical_block_size granularity. And at the same time use the UNMAP
command with the device's preferred granulary and alignment for discard
operations.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Try to use a write same with unmap bit variant if the device supports it
and the caller allows for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Split sd_setup_discard_cmnd into one function per provisioning type. While
this creates some very slight duplication of boilerplate code it keeps the
code modular for additions of new provisioning types, and for reusing the
write same functions for the upcoming scsi implementation of the Write Zeroes
operation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.
Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.
Cc: <stable@vger.kernel.org>
Reported-by: Steve Magnani <steve.magnani@digidescorp.com>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add fix to read correct register value for ISP82xx, during check for
register disconnect.ISP82xx has different base register.
Fixes: a465537ad1 ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect")
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.
Cc: <stable@vger.kernel.org>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If device reports a small max_xfer_blocks and a zero opt_xfer_blocks, we
end up using BLK_DEF_MAX_SECTORS, which is wrong and r/w of that size
may get error.
[mkp: tweaked to avoid setting rw_max twice and added typecast]
Cc: <stable@vger.kernel.org> # v4.4+
Fixes: ca369d51b3 ("block/sd: Fix device-imposed transfer length limits")
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We've added a considerable amount of fixes for stalls and issues
with the blk-mq scheduling in the 4.11 series since forking
off the for-4.12/block branch. We need to do improvements on
top of that for 4.12, so pull in the previous fixes to make
our lives easier going forward.
Signed-off-by: Jens Axboe <axboe@fb.com>
If a .queue_rq() function returns BLK_MQ_RQ_QUEUE_BUSY then the block
driver that implements that function is responsible for rerunning the
hardware queue once requests can be queued again successfully.
commit 52d7f1b5c2 ("blk-mq: Avoid that requeueing starts stopped
queues") removed the blk_mq_stop_hw_queue() call from scsi_queue_rq()
for the BLK_MQ_RQ_QUEUE_BUSY case. Hence change all calls to functions
that are intended to rerun a busy queue such that these examine all
hardware queues instead of only stopped queues.
Since no other functions than scsi_internal_device_block() and
scsi_internal_device_unblock() should ever stop or restart a SCSI
queue, change the blk_mq_delay_queue() call into a
blk_mq_delay_run_hw_queue() call.
Fixes: commit 52d7f1b5c2 ("blk-mq: Avoid that requeueing starts stopped queues")
Fixes: commit 7e79dadce2 ("blk-mq: stop hardware queue in blk_mq_delay_queue()")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The redundant init_completion() here seems to be a cut&past error as
struct scsi_qla_host only has 4 completion elements to initialize, thus
the duplicate init_completion(disable_acb_comp) is simply removed.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There hasn't been any reports for HBAs where asynchronous abort
would not work, so we should make it mandatory and remove
the fallback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_eh_scmd_add() currently only will fail if no
error handler thread is started (which will never be the
case) or if the state machine encounters an illegal transition.
But if we're encountering an invalid state transition
chances is we cannot fixup things with the error handler.
So better add a WARN_ON for illegal host states and
make scsi_dh_scmd_add() a void function.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a failed command is retried and fails again we need
to enter SCSI EH, otherwise we will never be able to
recover the command.
To detect this situation we must not clear scmd->eh_eflags
when EH finishes but rather make it persistent throughout
the lifetime of the command.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We now first try to call ->eh_abort_handler from a work queue, but libsas
was always failing that for no good reason. Allow async aborts.
Reviewed-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a command has timed out we always should be sending an
abort; with the previous code a failed abort might signal
SCSI EH to start, and all other timed out commands will
never be aborted, even though they might belong to a
different ITL nexus.
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If sd_eh_action() decides to take the device offline there is
no point in returning FAILED, as taking the device offline
is the ultimate step in SCSI EH anyway.
So further escalation via SCSI EH is not likely to make a
difference and we can as well return SUCCESS.
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current medium access timeout counter will be increased for
each command, so if there are enough failed commands we'll hit
the medium access timeout for even a single device failure and
the following kernel message is displayed:
sd H:C:T:L: [sdXY] Medium access timeout failure. Offlining disk!
Fix this by making the timeout per EH run, ie the counter will
only be increased once per device and EH run.
Fixes: 18a4d0a ("[SCSI] Handle disk devices which can not process medium access commands")
Cc: Ewan Milne <emilne@redhat.com>
Cc: Lawrence Obermann <loberman@redhat.com>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Cc: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
And get automatic MSI-X affinity for free.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The commit 08024885a2 ("ses: Add power_status to SES device slot")
introduced the 'power_status' attribute to enclosure components and
the associated callbacks.
There are 2 callbacks available to get the power status of a device:
1) ses_get_power_status() for 'struct enclosure_component_callbacks'
2) get_component_power_status() for the sysfs device attribute
(these are available for kernel-space and user-space, respectively.)
However, despite both methods being available to get power status
on demand, that commit also introduced a call to get power status
in ses_enclosure_data_process().
This dramatically increased the total probe time for SCSI devices
on larger configurations, because ses_enclosure_data_process() is
called several times during the SCSI devices probe and loops over
the component devices (but that is another problem, another patch).
That results in a tremendous continuous hammering of SCSI Receive
Diagnostics commands to the enclosure-services device, which does
delay the total probe time for the SCSI devices __significantly__:
Originally, ~34 minutes on a system attached to ~170 disks:
[ 9214.490703] mpt3sas version 13.100.00.00 loaded
...
[11256.580231] scsi 17:0:177:0: qdepth(16), tagged(1), simple(0),
ordered(0), scsi_level(6), cmd_que(1)
With this patch, it decreased to ~2.5 minutes -- a 13.6x faster
[ 1002.992533] mpt3sas version 13.100.00.00 loaded
...
[ 1151.978831] scsi 11:0:177:0: qdepth(16), tagged(1), simple(0),
ordered(0), scsi_level(6), cmd_que(1)
Back to the commit discussion.. on the ses_get_power_status() call
introduced in ses_enclosure_data_process(): impact of removing it.
That may possibly be in place to initialize the power status value
on device probe. However, those 2 functions available to retrieve
that value _do_ automatically refresh/update it. So the potential
benefit would be a direct access of the 'power_status' field which
does not use the callbacks...
But the only reader of 'struct enclosure_component::power_status'
is the get_component_power_status() callback for sysfs attribute,
and it _does_ check for and call the .get_power_status callback,
(which indeed is defined and implemented by that commit), so the
power status value is, again, automatically updated.
So, the remaining potential for a direct/non-callback access to
the power_status attribute would be out-of-tree modules -- well,
for those, if they are for whatever reason interested in values
that are set during device probe and not up-to-date by the time
they need it.. well, that would be curious.
Well, to handle that more properly, set the initial power state
value to '-1' (i.e., uninitialized) instead of '1' (power 'on'),
and check for it in that callback which may do an direct access
to the field value _if_ a callback function is not defined.
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Fixes: 08024885a2 ("ses: Add power_status to SES device slot")
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of bloating the generic struct request with it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
sas_domain_release_transport is unused since at least v3.13, remove it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Milan P Gandhi <mgandhi@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc-7.0.1 now warns about a previously unnoticed access of uninitialized
struct members:
drivers/scsi/advansys.c: In function 'AscMsgOutSDTR':
drivers/scsi/advansys.c:3860:26: error: '*((void *)&sdtr_buf+5)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
((ushort)s_buffer[i + 1] << 8) | s_buffer[i]);
^
drivers/scsi/advansys.c:3860:26: error: '*((void *)&sdtr_buf+7)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/scsi/advansys.c:3860:26: error: '*((void *)&sdtr_buf+5)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/scsi/advansys.c:3860:26: error: '*((void *)&sdtr_buf+7)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code has existed in this exact form at least since v2.6.12, and the
warning seems correct. This uses named initializers to ensure we
initialize all members of the structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Thirteen small fixes: The hopefully final effort to get the lpfc nvme
kconfig problems sorted, there's one important sg fix (user can induce
read after end of buffer) and one minor enhancement (adding an extra
PCI ID to qedi). The rest are a set of minor fixes, which mostly occur
as user visible in error legs or on specific devices.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=umUo
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Thirteen small fixes: The hopefully final effort to get the lpfc nvme
kconfig problems sorted, there's one important sg fix (user can induce
read after end of buffer) and one minor enhancement (adding an extra
PCI ID to qedi). The rest are a set of minor fixes, which mostly occur
as user visible in error legs or on specific devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: remove the duplicated checking for supporting clkscaling
scsi: lpfc: fix building without debugfs support
scsi: lpfc: Fix PT2PT PRLI reject
scsi: hpsa: fix volume offline state
scsi: libsas: fix ata xfer length
scsi: scsi_dh_alua: Warn if the first argument of alua_rtpg_queue() is NULL
scsi: scsi_dh_alua: Ensure that alua_activate() calls the completion function
scsi: scsi_dh_alua: Check scsi_device_get() return value
scsi: sg: check length passed to SG_NEXT_CMD_LEN
scsi: ufshcd-platform: remove the useless cast in ERR_PTR/IS_ERR
scsi: qedi: Add PCI device-ID for QL41xxx adapters.
scsi: aacraid: Fix potential null access
scsi: qla2xxx: Fix crash in qla2xxx_eh_abort on bad ptr
Constify all instances of blk_mq_ops, as they are never modified.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
And get automatic MSI-X affinity for free.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 61e073590b.
The patch introduced redundant query retries as we already had such
mechanism provided with _retry functions. Both ufshcd_read_desc and
ufshcd_read_unit_desc_param functions call ufshcd_query_descriptor_retry
wrapper.
Signed-off-by: Szymon Mielczarek <szymonx.mielczarek@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removing the 'select SCSI_SAS_LIBSAS' statement in Kconfig resulted in a
link failure in configurations that have hisi_sas built-in but libsas as
a loadable module:
drivers/scsi/built-in.o: In function `hisi_sas_scan_finished':
hisi_sas_main.c:(.text+0x37ce9): undefined reference to `sas_drain_work'
drivers/scsi/built-in.o: In function `hisi_sas_slave_configure':
hisi_sas_main.c:(.text+0x37d17): undefined reference to `sas_slave_configure'
hisi_sas_main.c:(.text+0x37d40): undefined reference to `sas_change_queue_depth'
drivers/scsi/built-in.o: In function `hisi_sas_remove':
All other libsas users have the 'select' statement, so we should do the
same here for consistency. For all I can tell, the patch that added the
sata softreset does not actually introduce a dependency on SCSI_SAS_ATA
but instead adds calls into libata itself, so we can express that with a
more specific dependency.
We cannot have 'select SCSI_SAS_LIBSAS; depends on SCSI_SAS_ATA' as that
would cause a dependency loop.
Fixes: 7c594f0407 ("scsi: hisi_sas: add softreset function for SATA disk")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Not much reason to use ARRAY_SIZE() when we know it's for a C string.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These flags are no longer needed after 2fbd009b in 2013.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add macros for register bits that can be found in JESD223C (v2.1).
Not all registers are defined in ufshci.h (i.e. some are unused whether
macros are defined or undefined), but all the bits for those registers
that are already defined should appear here.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Not having () isn't likely to do any harm in this case, but all the
other macros below do have it. Also add "are" in a comment.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd driver generally uses bool for is_xxx type things instead of int,
so conform to its style.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It appears that a break in the TRANS_TX_OPEN_CNX_ERR_NO_DESTINATION case
got accidentally removed in an earlier commit, as it stands, the
ts->stat and ts->open_rej_reason are being updated twice for this case
which looks incorrect. Fix this by adding in the missing break
statement.
Detected by CoverityScan, CID#1422110 ("Missing break in switch")
Fixes: 634a9585f4 ("scsi: hisi_sas: process error codes according to their priority")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Version 11.4.0.0
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update Broadcom Copyright markings in all files.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Data in buffers are gathered into a single buffer before giving to iSCSI
layer. Though less likely to have payload more than 8K in ASYNC PDU, the
data length is provide by FW and check is missing for overrun.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With previous patch adding ASYNC Rx buffers to free_list is not
required. Remove all free_list related operations.
Add in_use to track if buffer posted is being processed by driver and
purge all buffers received for connection if found so.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FW runs out of buffer if buffers are not posted back soon. ASYNC Rx CQE
indicates that FW has consumed 8 RQEs. Use it to post back buffers
instead of waiting for buffers to be processed and freed by driver.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, ASYNC PDU default queue size is set to max connections. This
leaves only one buffer per connection for any ASYNC PDUs from targets.
Double the size of the default queue.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_flush_work flushes workqueue for the Scsi_Host. In iSCSI offload
enabled host, this would wait for all other sessions under the host.
Use flush_work for the session being removed instead.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
spin_unlock_bh back_lock is used in beiscsi_eh_device_reset instead of
spin_lock.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CID needs to be freed even when invalidate or upload connection fails.
Attempt to close connection 3 times before freeing CID.
Set cleanup_type to INVALIDATE instead of force TCP_RST. This
unnecessarily is terminating connection with reset instead of gracefully
closing it.
Set save_cfg to 0 - session not to be saved on flash.
Add delay and process CQ before uploading connection.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These aren't really falling through to anywhere meaningful.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We don't call the remove() function unless probe() succeeds so "oud"
can't be NULL here. Plus, if it were NULL, we dereference it on the
next line so it would crash anyway.
[mkp: applied by hand]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boaz Harrosh <ooo@electrozaur.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are same conditions for checking whether supporting clkscaling or
not. When ufshcd is supporting clkscaling, active_reqs should be
decreased by one.
[mkp: addressed comment from Bartlomiej]
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
My email address may be found in the git commit logs and in MAINTAINERS.
Remove duplicate addresses so they won't have to be kept up-to-date.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fix some spelling typos found in printk.
[jkosina@suse.cz: drop arch/arm64/kernel/hibernate.c that was already
in place]
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc points out that we are converting a 16-bit integer into a 32-bit
little-endian type and assigning that to 16-bit little-endian
will end up with a zero:
drivers/scsi/qedf/drv_fcoe_fw_funcs.c: In function 'init_initiator_rw_fcoe_task':
include/uapi/linux/byteorder/big_endian.h:32:26: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
t_st_ctx->read_write.rx_id = cpu_to_le32(FCOE_RX_ID);
The correct solution appears to be to just use a 16-bit byte swap instead.
Fixes: be086e7c53 ("qed*: Utilize Firmware 8.15.3.0")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump driver version
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes a hang that can occur in ATA EH with ipr. With ipr's
usage of libata, commands should never end up on ap->eh_done_q. The
timeout function we use for ipr, even for SATA devices, is
scsi_times_out, so ATA_QCFLAG_EH_SCHEDULED never gets set for ipr and EH
is driven completely by ipr and SCSI. The SCSI EH thread ends up calling
ipr's eh_device_reset_handler, which then calls
ata_std_error_handler. This ends up calling ipr_sata_reset, which issues
a reset to the device. This should result in all pending commands
getting failed back and having ata_qc_complete called for them, which
should end up clearing ATA_QCFLAG_FAILED as qc->flags gets zeroed in
ata_qc_free. This ensures that when we end up in ata_eh_finish, we
don't do anything more with the command.
On adapters that only support a single interrupt and when running with
two MSI-X vectors or less, the adapter firmware guarantees that
responses to all outstanding commands are sent back prior to sending the
response to the SATA reset command. On newer adapters supporting
multiple HRRQs, however, this can no longer be guaranteed, since the
command responses and reset response may be processed on different
HRRQs.
If ipr returns from ipr_sata_reset before the outstanding command was
returned, this sends us down the path of __ata_eh_qc_complete which then
moves the associated scsi_cmd from the work_q in
scsi_eh_bus_device_reset to ap->eh_done_q, which then will sit there
forever and we will be wedged.
This patch fixes this up by ensuring that any outstanding commands are
flushed before returning from eh_device_reset_handler for a SATA device.
Reported-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch closes up some potential race conditions observed in the
error handling paths in ipr while debugging an issue resulting in a hang
with SATA error handling. These patches ensure we are holding the
correct lock when adding and removing commands from the free and pending
queues in some error scenarios.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This fixes a race condition in the error handlomg paths of ipr. While a
command is outstanding to the adapter, it is placed on a pending queue
for the hrrq it is associated with, while holding the HRRQ lock. When a
command is completed, it is removed from the pending queue, under HRRQ
lock, and placed on a local list. This list is then iterated through
without any locks and each command's done function is invoked, inside of
which, the command gets returned to the free list while grabbing the
HRRQ lock. This fixes two race conditions when commands have been
removed from the pending list but have not yet been added to the free
list. Both of these changes fix race conditions that could result in
returning success from eh_abort_handler and then later calling scsi_done
for the same request.
The first race condition is in ipr_cancel_op. It looks through each
pending queue to see if the command to be aborted is still outstanding
or not. Rather than looking on the pending queue, reverse the logic to
check to look for commands that are NOT on the free queue. The second
race condition can occur when in ipr_wait_for_ops where we are waiting
for responses for commands we've aborted.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removes some code in __ipr_eh_dev_reset which was modifying the ipr_cmd
done function. This should have already been setup at command allocation
time and if its since been changed, it means we are in the ipr_erp*
functions and need to wait for them to complete and don't want to
override that here.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following a command abort or device reset, ipr's EH handlers wait for
the commands getting aborted to get sent back from the adapter prior to
returning from the EH handler. This fixes up some cases where the
completion handler was not getting called, which would have resulted in
the EH thread waiting until it timed out, greatly extending EH time.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a randconfig build without CONFIG_SCSI_LPFC_DEBUG_FS, I ran into
multiple compile failures:
drivers/scsi/lpfc/lpfc_debugfs.h: In function 'lpfc_debug_dump_wq':
drivers/scsi/lpfc/lpfc_debugfs.h:405:15: error: 'DUMP_FCP' undeclared (first use in this function); did you mean 'DUMP_VAR'?
drivers/scsi/lpfc/lpfc_debugfs.h:405:15: note: each undeclared identifier is reported only once for each function it appears in
drivers/scsi/lpfc/lpfc_debugfs.h:408:22: error: 'DUMP_NVME' undeclared (first use in this function); did you mean 'DUMP_NONE'?
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_ls_rsp_cmp':
drivers/scsi/lpfc/lpfc_nvmet.c:109:2: error: implicit declaration of function 'lpfc_nvmeio_data'; did you mean 'lpfc_mem_free'? [-Werror=implicit-function-declaration]
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_fcp_op':
drivers/scsi/lpfc/lpfc_nvmet.c:523:10: error: unused variable 'id' [-Werror=unused-variable]
They are all trivial to fix, so I'm doing it in a combined patch here.
Fixes: 1d9d5a9879 ("scsi: lpfc: refactor debugfs queue dump routines")
Fixes: bd2cdd5e40 ("scsi: lpfc: NVME Initiator: Add debugfs support")
Fixes: 2b65e18202 ("scsi: lpfc: NVME Target: Add debugfs support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc cannot establish connection with targets that send PRLI in P2P
configurations.
If lpfc rejects a PRLI that is sent from a target the target will not
resend and will reject the PRLI send from the initiator.
[mkp: applied by hand]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add helper function is_sata_phy_v2_hw() to judge whether the attached
device is SATA disk for a root PHY.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SMP IO is sent, sas_protocol_ata couldn't judge whether the disk is
SATA or SAS disk. So use dev_is_sata to identify SATA or SAS disk.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unless we actually get some sort of failure in hisi_sas_lu_reset(),
don't print a message.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an SMP task timeouts, it will call lldd_abort_task to release the
associated slot, and then will release the sas_task.
Currently in lldd_abort_task, if we fail to internally abort IO, then
the slot of SMP IO is not released, but sas_task will still be later
released, so the slot's sas_task is NULL, which will cause NULL pointer
when hisi_sas_slot_task_free happens later.
To resolve, check the return value of internal abort, and release the
slot if it failed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add function for upper-layer to reset controller when all else fails.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For consistency, remove the "hisi_sas_" prefix.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Handle the situation that PHY UP and DOWN irq happen simultaneously.
There is no mechanism of SoC HW to ensure this situation will never
happen. So, we add this handle just in case.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch includes:
(1) Disable transport layer retry
(2) Support CQ time and count interrupt coal
(3) fix link FIFO full issue
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Zhao Nenglong <zhaonenglong@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are some rules to decide which error code has the high priority
when errors happen together:
(1) Error phase of CQ decides the error happens on RX or TX;
(2) For TX error, when DMA/TRANS TX error happen simultaneously, the
priority of DMA TX error is higher than TRANS TX error, so for the
priority of TX error: DW2 (DMA TX part) > DW0;
(3) For RX error, when TRANS/DMA/SIPC RX error happen simultaneously,
the priority of TRANS RX error is higher than DMA and SIPC RX error,
and we should also keep the rules (the priority of DW3 > DW2), so
for the priority of RX error: DW1 > DW3 > DW2(SIPC RX part);
(4) There are also a priority we should keep in the same error type.
So, modify slot error code to handle this.
In addition to this, some some error codes are modified according to
recommendation from SoC designer.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a TMF or internal abort times-out, do not free slot. We expect this
to be done upon later escalated error handling.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some more locking needs to be added/modified for when
read-modify-writing sas_task.task_state_flags.
Note: since we can attempt to grab this lock in interrupt
context we should use irq variant of spin_lock.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After hardreset, we clear up IOs of remote disks, so we need to free
those slots in LLDD.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check in slot_complete_v2_hw() for whether a task has already been
completed by upper layer.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When issuing an LU reset for a SATA target, issue an internal abort and
a hard reset.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently an internal abort is executed regardless of the result of the
TMF. We should also check the result of the internal abort to see if we
should free the slot.
So change the status code STAT_IO_COMPLETE to TMF_RESP_FUNC_SUCC,
meaning the slot has been successfully aborted.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For error codes which need abort-and-retry, simulate IO timeout and let
SCSI+ATA layers process those errors.
Previously for SSP, we should try to abort the IO in the LLDD and then
pass back to upper layer, but sometimes this would also error. So
Instead of adding special error handling for this scenario in the LLDD,
allow the upper layer to handle completely.
No performance hit is seen by taking this approach.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We currently do a hard reset for a link reset. Change this to do a link
reset only.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sas_port is NULL, then return SAS_PHY_DOWN.
In addition, when the sas_dev is gone then explicitly return
SAS_PHY_DOWN.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently when a root PHY is deformed from a asd_sas_port we try to
release the slots in the LLDD, and fail.
Regardless, it is not right to release this early.
This patch removes the deformed function. As it was before, port
deformation is still done in hisi_sas_phy_down().
It would be nice to actually remove the hisi_sas_port_{de}formed() pair,
however we cannot as we need to know the asd_sas_port index libsas has
associated with an asd_sas_phy.
The hw does actually generate a port id for a PHY, but this seems to a
random number, so ignored for this purpose.
This patch also changes the code to link slots to the hisi_sas_device,
and not hisi_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add softreset to clear IO after internal abort device for SATA disk.
The SATA error handling for the controller is based on device internal
abort and softreset function.
The controller does not support internal abort for single IO, so we need
to execute internal abort for device.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate the PHY init code from LLDD hw init path to
hisi_sas_scan_start().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are some scenarios that we need to warm-reset to reset registers
of SAS controller. During reset we disable interrupts/DQs/PHYs, and
after reset we re-init the hardware and rescan the topology to see if
anything changed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce function to get hisi_sas_port from asd_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a previous patch a hpsa_scsi_dev_t.volume_offline update line has
been removed, so let us put it back..
Fixes: 85b29008d8 (hpsa: update check for logical volume status)
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a bug introduced when they moved the fip subcodes to central
place. Was sending FIP_SC_VL_NOTE in fip.fip_subcode for VLAN request in
fnic_fcoe_send_vlan_req. Change is to use FIP_SC_VL_REQ instead.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The IO and Abort latency counter counts the time taken to complete the
IO and abort command into broad buckets. This is not intended for
performance measurement, just a debug statistic. current_max_io_time
tries to keep track of the maximum time an IO has taken to complete if
it is > 30sec.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just a simple counter of number of check conditions encountered on that
host.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SCSI-ML has already issued abort on a command i.e
FNIC_IOREQ_ABTS_PENDING is set and we get a IO completion, avoid this
being flagged as out-of-order completion by setting the FNIC_IO_DONE
flag in fnic_fcpio_icmnd_cmpl_handler
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixing the IO stats update (Active IOs and IO completion) to prevent
"Number of Active IOs" from becoming negative in the fnistats output.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Getting rid of else case to make the flow look bit simpler.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is to avoid the log from being filled with vlan discovery messages
when there is no vlan configured on the switch.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Not a full cleanup for the IRQ code, for that we'd need to know if the
max number of the various CQ types is going to stay 1 forever.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nine small fixes: the biggest is probably finally sorting out Kconfig
issues with lpfc nvme. There are some performance fixes for megaraid
and hpsa and a static checker fix.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Z4Xj
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine small fixes: the biggest is probably finally sorting out Kconfig
issues with lpfc nvme. There are some performance fixes for megaraid
and hpsa and a static checker fix"
[ Johannes Thumshirn points out that there still seems to be more lpfc
vs nvme config issues. Oh well. - Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Finalize Kconfig options for nvme
scsi: ufs: don't check unsigned type for a negative value
scsi: hpsa: do not timeout reset operations
scsi: hpsa: limit outstanding rescans
scsi: hpsa: update check for logical volume status
scsi: megaraid_sas: Driver version upgrade
scsi: megaraid_sas: raid6 also require cpuSel check same as raid5
scsi: megaraid_sas: add correct return type check for ldio hint logic for raid1
scsi: megaraid_sas: enable intx only if msix request fails
This driver did not set kobj.parent so it likely suffered from
a potential use after free race if the user unregistered the
device while it was in use.
This was not so straightforward a conversion but I think this patch
cleans up its probe's error path significantly.
This patch adds device_initialize, which is required for
cdev_device_add. Then it switches to put_device instead of kfree as
recommended by device_initialize's documentation. This removes a lot
from the error path which was already in __remove.
A couple things needed to be re-ordered to be entirely correct, though.
ida_remove is also moved out of __remove and into unregister to
simplify things and follow the pattern other devices are using.
This also drop an extra unnecessary get_device/put_device in the code.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The total ata xfer length may not be calculated properly, in that we do
not use the proper method to get an sg element dma length.
According to the code comment, sg_dma_len() should be used after
dma_map_sg() is called.
This issue was found by turning on the SMMUv3 in front of the hisi_sas
controller in hip07. Multiple sg elements were being combined into a
single element, but the original first element length was being use as
the total xfer length.
Cc: <stable@vger.kernel.org>
Fixes: ff2aeb1eb6 ("libata: convert to chained sg")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull SCSI target fixes from Nicholas Bellinger:
"The bulk of the changes are in qla2xxx target driver code to address
various issues found during Cavium/QLogic's internal testing (stable
CC's included), along with a few other stability and smaller
miscellaneous improvements.
There are also a couple of different patch sets from Mike Christie,
which have been a result of his work to use target-core ALUA logic
together with tcm-user backend driver.
Finally, a patch to address some long standing issues with
pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
which will make folks using physical (or virtual) magnetic tape happy"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
qla2xxx: Update driver version to 9.00.00.00-k
qla2xxx: Fix delayed response to command for loop mode/direct connect.
qla2xxx: Change scsi host lookup method.
qla2xxx: Add DebugFS node to display Port Database
qla2xxx: Use IOCB interface to submit non-critical MBX.
qla2xxx: Add async new target notification
qla2xxx: Export DIF stats via debugfs
qla2xxx: Improve T10-DIF/PI handling in driver.
qla2xxx: Allow relogin to proceed if remote login did not finish
qla2xxx: Fix sess_lock & hardware_lock lock order problem.
qla2xxx: Fix inadequate lock protection for ABTS.
qla2xxx: Fix request queue corruption.
qla2xxx: Fix memory leak for abts processing
qla2xxx: Allow vref count to timeout on vport delete.
tcmu: Convert cmd_time_out into backend device attribute
tcmu: make cmd timeout configurable
tcmu: add helper to check if dev was configured
target: fix race during implicit transition work flushes
target: allow userspace to set state to transitioning
target: fix ALUA transition timeout handling
...
Callers must provide a valid port group to alua_rtpg_queue(). Issue a
kernel warning if that is not the case.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Callers of scsi_dh_activate(), e.g. dm-mpath, assume that this function
either returns an error code or calls the completion function. Make
alua_activate() call the completion function even if scsi_device_get()
fails.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Cc: <stable@vger.kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.
Following commands are being routed through IOCB interface
- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.
Use hardware_lock only for error response in this case.
Path1
CPU0 CPU1
---- ----
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0
Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Buffer is a pointer to the static char array event_buffer and therefore
can never be null, so the check is redundant. Remove it.
Detected by CoverityScan, CID#1077556 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The user can control the size of the next command passed along, but the
value passed to the ioctl isn't checked against the usable max command
size.
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Chang <dpf@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Even if bus is not hot-pluggable, devices can be unbound from the driver
via sysfs, so we should not be using __exit annotations on remove()
methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Add reboot notifier and register it in stex_probe for all supported
device.
2. For all supported device in restart flow, we get a callback from
notifier and set S6flag for stex_shutdown & stex_hba_stop to send
restart command to FW.
Signed-off-by: Charles.Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Paul.Lyu <paul.lyu@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pegasus series is a RAID support product using Thunderbolt technology.
The newest product, Pegasus 3(P3) supports Thunderbolt 3 technology with
a different chip.
1. Change driver version.
2. Add P3 VID, DID and define it's device address.
3. P3 use msi interrupt, so stex_request_irq P3 type enable msi.
4. For hibernation, use msi_lock in stex_ss_handshake to prevent msi
register write again when handshaking.
5. P3 doesn't need read() as flush.
6. In stex_ss_intr & stex_abort, P3 only clear interrupt register when
getting vendor defined interrupt.
Signed-off-by: Charles.Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Paul.Lyu <paul.lyu@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
IS_ERR and ERR_PTR already forcefully cast their argument, hence there
is no need for additional (complex) casting.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, command threads fails to return ioctls commands for older
controller versions, since it returns when all the fibs have been
allocated. Another issue is even all the fibs have not been allocated,
the correct allocated fibs is not updated nor freed.
Fixes: 113156bcea (scsi: aacraid: Reworked aac_command_thread)
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a Qlogic card breaks when initializing (test case), the system can
crash in qla2xxx_eh_abort if processing anything but a scsi command type
srb.
Fixes: 1535aa75a3 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-By: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
refcount_t type and corresponding API should be used instead of atomic_t
when the variable is used as a reference counter. This allows to avoid
accidental refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
refcount_t type and corresponding API should be used instead of atomic_t
when the variable is used as a reference counter. This allows to avoid
accidental refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmgenet.c
net/core/sock.c
Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a rather large set of fixes. The bulk are for lpfc correcting
a lot of issues in the new NVME driver code which just went in in the
merge window. The others are: fix a hang in the vmware paravirt
driver caused by incorrect handling of the new MSI vector allocation.
A long standing bug in storvsc, which recent block changes turned from
being a harmless annoyance into a hang and yet more fallout (in
mpt3sas) from the changes to device blocking. The remainder are small
fixes and updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJYyXW+AAoJEAVr7HOZEZN4yzIP/R2qDzwoXw3dl5xHs2AQuxWU
P7mbUqtN2meU0klIKNCaYq6WO797WvGblSldrPwB08M7QOg8vy7boNiCYmwdEs6W
Ftihj99OwEp0598MldNw1hBtMqjJ1WSu/kLK/I3pjLjltyPbQunuvaEwSNvxD1r7
8BRmngYLFPb3KQDSO74ILBdZ5DqsriIXDHlngKSKfrpjO5IWXHrmzhZTmU2qpE40
H4C4+Kn3/iZKGRiMm4rsikRDEGty9aVo7f4CIrwWslLkaJWf/AS4Kf3rd5qqclRj
crjP/axqXheuwggKaHNhnxX5oSGt61ZCH9lGMmSNV/q6pUtNsrhO2uZuBIP0vtDB
y7Pfw0Z3MGnbsOmBhZLRnUYC9PgSZPysy3TuS6/BgGx2ZFPnFxXjA1T73YaUil9q
zcCOV2E7WHjIFGrpF2jNmoGsh1360TUOjg8YXdLi8pC2sEqSU331nvB5W9xAw3EG
ewusZFetumxV8pykSyuDknU5gAMVYhHv+I+eNP8SB0eUZTLeKlcZpWIt3QYSYRdJ
KbCc4CSi28J+DghB86eRZC64QqFiYMP546zUPpD1Enh/HXtVrTYzRN9/Qwo2FJRZ
s5E3aC6tPceSuOmqn4aL9+Il7NXDj1Y/M9Qwe6Dzjp7q8hLCb7J1TWY3G5ImBWI7
TfdyBrvZerqpxga+6j5g
=0mha
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a rather large set of fixes. The bulk are for lpfc correcting
a lot of issues in the new NVME driver code which just went in in the
merge window.
The others are:
- fix a hang in the vmware paravirt driver caused by incorrect
handling of the new MSI vector allocation
- long standing bug in storvsc, which recent block changes turned
from being a harmless annoyance into a hang
- yet more fallout (in mpt3sas) from the changes to device blocking
The remainder are small fixes and updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (34 commits)
scsi: lpfc: Add shutdown method for kexec
scsi: storvsc: Workaround for virtual DVD SCSI version
scsi: lpfc: revise version number to 11.2.0.10
scsi: lpfc: code cleanups in NVME initiator discovery
scsi: lpfc: code cleanups in NVME initiator base
scsi: lpfc: correct rdp diag portnames
scsi: lpfc: remove dead sli3 nvme code
scsi: lpfc: correct double print
scsi: lpfc: Rename LPFC_MAX_EQ_DELAY to LPFC_MAX_EQ_DELAY_EQID_CNT
scsi: lpfc: Rework lpfc Kconfig for NVME options
scsi: lpfc: add transport eh_timed_out reference
scsi: lpfc: Fix eh_deadline setting for sli3 adapters.
scsi: lpfc: add NVME exchange aborts
scsi: lpfc: Fix nvme allocation bug on failed nvme_fc_register_localport
scsi: lpfc: Fix IO submission if WQ is full
scsi: lpfc: Fix NVME CMD IU byte swapped word 1 problem
scsi: lpfc: Fix RCTL value on NVME LS request and response
scsi: lpfc: Fix crash during Hardware error recovery on SLI3 adapters
scsi: lpfc: fix missing spin_unlock on sql_list_lock
scsi: lpfc: don't dereference dma_buf->iocbq before null check
...
Reviewing the result of what was just added for Kconfig, we made a poor
choice. It worked well for full kernel builds, but not so much for how
it would be deployed on a distro.
Here's the final result:
- lpfc will compile in NVME initiator and/or NVME target support based
on whether the kernel has the corresponding subsystem support.
Kconfig is not used to drive this specifically for lpfc.
- There is a module parameter, lpfc_enable_fc4_type, that indicates
whether the ports will do FCP-only or FCP & NVME (NVME-only not yet
possible due to dependency on fc transport). As FCP & NVME divvys up
exchange resources, and given NVME will not be often initially, the
default is changed to FCP only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Resets can take longer than DEFAULT_TIMEOUT.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid rescan storms. No need to queue another if one is pending.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Add in a new case for volume offline. Resolves internal testing bug
for multilun array management.
- Return correct status for failed TURs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without this fix, raid6 performance will not be optimal.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return value check of atomic_dec_if_positive is required as it returns
old value minus one. Without this fix, driver will send small ios to
firmware path and that will be a performance issue.
Not critical, but good to have r1_ldio_hint as default value in sdev
private.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without this fix, driver will enable INTx Interrupt pin even though
MSI-x vectors are enabled. See below lspci output. DisINTx is unset for
MSIx setup.
lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
After applying this fix, driver will enable INTx Interrupt pin only if
Legacy interrupt method is required. See below lspci output. DisINTx is
set for MSIx setup. lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch advances the qed* drivers into using the newer firmware -
This solves several firmware bugs, mostly related [but not limited to]
various init/deinit issues in various offloaded protocols.
It also introduces a major 4-Cached SGE change in firmware, which can be
seen in the storage drivers' changes.
In addition, this firmware is required for supporting the new QL41xxx
series of adapters; While this patch doesn't add the actual support,
the firmware contains the necessary initialization & firmware logic to
operate such adapters [actual support would be added later on].
Changes from Previous versions:
-------------------------------
- V2 - fix kbuild-test robot warnings
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge fixes from Andrew Morton:
"26 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (26 commits)
userfaultfd: remove wrong comment from userfaultfd_ctx_get()
fat: fix using uninitialized fields of fat_inode/fsinfo_inode
sh: cayman: IDE support fix
kasan: fix races in quarantine_remove_cache()
kasan: resched in quarantine_remove_cache()
mm: do not call mem_cgroup_free() from within mem_cgroup_alloc()
thp: fix another corner case of munlock() vs. THPs
rmap: fix NULL-pointer dereference on THP munlocking
mm/memblock.c: fix memblock_next_valid_pfn()
userfaultfd: selftest: vm: allow to build in vm/ directory
userfaultfd: non-cooperative: userfaultfd_remove revalidate vma in MADV_DONTNEED
userfaultfd: non-cooperative: fix fork fctx->new memleak
mm/cgroup: avoid panic when init with low memory
drivers/md/bcache/util.h: remove duplicate inclusion of blkdev.h
mm/vmstats: add thp_split_pud event for clarity
include/linux/fs.h: fix unsigned enum warning with gcc-4.2
userfaultfd: non-cooperative: release all ctx in dup_userfaultfd_complete
userfaultfd: non-cooperative: robustness check
userfaultfd: non-cooperative: rollback userfaultfd_exit
x86, mm: unify exit paths in gup_pte_range()
...
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 0dba1314d4. It causes
leaking of device numbers for SCSI when SCSI registers multiple gendisks
for one request_queue in succession. It can be easily reproduced using
Omar's script [1] on kernel with CONFIG_DEBUG_TEST_DRIVER_REMOVE.
Furthermore the protection provided by this commit is not needed anymore
as the problem it was fixing got also fixed by commit 165a5e22fa
"block: Move bdi_unregister() to del_gendisk()".
[1]: http://marc.info/?l=linux-block&m=148554717109098&w=2
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We see lpfc devices regularly fail during kexec. Fix this by adding a
shutdown method which mirrors the remove method.
Cc: <stable@vger.kernel.org>
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hyper-V host emulation of SCSI for virtual DVD device reports SCSI
version 0 (UNKNOWN) but is still capable of supporting REPORTLUN.
Without this patch, a GEN2 Linux guest on Hyper-V will not boot 4.11
successfully with virtual DVD ROM device. What happens is that the SCSI
scan process falls back to doing sequential probing by INQUIRY. But the
storvsc driver has a previous workaround that masks/blocks all errors
reports from INQUIRY (or MODE_SENSE) commands. This workaround causes
the scan to then populate a full set of bogus LUN's on the target and
then sends kernel spinning off into a death spiral doing block reads on
the non-existent LUNs.
By setting the correct blacklist flags, the target with the DVD device
is scanned with REPORTLUN and that works correctly.
Patch needs to go in current 4.11, it is safe but not necessary in older
kernels.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise lpfc version number to 11.2.0.10
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch addresses the smatch issues identified by Dan Carpenter
in http://www.spinics.net/lists/linux-scsi/msg105665.html
The issues are:
drivers/scsi/lpfc/lpfc_ct.c:943 lpfc_cmpl_ct_cmd_gft_id()
error: we previously assumed 'ndlp' could be null (see line 928)
Action: moved under if check
drivers/scsi/lpfc/lpfc_nvmet.c:1694 lpfc_nvmet_unsol_issue_abort()
error: we previously assumed 'ndlp' could be null (see line 1690)
Action: conditionalized arg in printf stmt
drivers/scsi/lpfc/lpfc_nvmet.c:1792 lpfc_nvmet_sol_fcp_issue_abort()
error: we previously assumed 'ndlp' could be null (see line 1788)
Action: conditionalized arg in printf stmt
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch addresses the smatch issues identified by Dan Carpenter
in http://www.spinics.net/lists/linux-scsi/msg105663.html
The issues are:
drivers/scsi/lpfc/lpfc_hbadisc.c:316 lpfc_dev_loss_tmo_handler()
warn: we tested 'vport->load_flag & 2' before and it was 'false'
Action: removed item from test
drivers/scsi/lpfc/lpfc_hbadisc.c:701 lpfc_work_done()
warn: test_bit() takes a bit number
Action: changed definition so bit number
drivers/scsi/lpfc/lpfc_hbadisc.c:2206 lpfc_mbx_cmpl_fcf_scan_read_fcf_rec()
error: uninitialized symbol 'vlan_id'.
drivers/scsi/lpfc/lpfc_hbadisc.c:2582 lpfc_mbx_cmpl_fcf_rr_read_fcf_rec()
error: uninitialized symbol 'vlan_id'.
drivers/scsi/lpfc/lpfc_hbadisc.c:2683 lpfc_mbx_cmpl_read_fcf_rec() error:
uninitialized symbol 'vlan_id'.
Action: initilized value
drivers/scsi/lpfc/lpfc_hbadisc.c:4025 lpfc_register_remote_port()
error: we previously assumed 'rdata' could be null (see line 4023)
Action: refactored check block
drivers/scsi/lpfc/lpfc_hbadisc.c:4613 lpfc_sli4_dequeue_nport_iocbs()
error: double unlock 'irq:'
Action: removed inner irq reference
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME merge reverted diag port names to the physical port.
They should be the vport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove nvme teardown calls that should not be there on sli3 devices
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a merge error that had debug data printed twice for the
same element
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without apriori understanding of what the define is, the name gives
a very different impression of what it is (a max delay value
for an EQ). Rename the define so it reflects what it is: the number
of EQ IDs that can be set in one instance of the MODIFY_EQ_DELAY
mbx command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reworked Kconfig so that lfpc only requires the scsi stack.
NVME Initiator and NVME Target support can be enabled if
the other NVMe subsystems have been enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph's prior patch missed the template for the sli3 adapters,
which is now the "no host reset" template. Add the transport
eh_timed_out handler to the no host reset template
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A previous change unilaterally removed the hba reset entry point
from the sli3 host template. This was done to allow tape devices
being used for back up from being removed. Why was this done ?
When there was non-responding device on the fabric, the error
escalation policy would escalate to the reset handler. When the
reset handler was called, it would reset the adapter, dropping
link, thus logging out and terminating all i/o's - on any target.
If there was a tape device on the same adapter that wasn't in
error, it would kill the tape i/o's, effectively killing the
tape device state. With the reset point removed, the adapter
reset avoided the fabric logout, allowing the other devices to
continue to operate unaffected. A hack - yes. Hint: we really
need a transport I_T nexus reset callback added to the eh process
(in between the SCSI target reset and hba reset points), so a
fc logout could occur to the one bad target only and stop the error
escalation process.
This patch commonizes the approach so it can be used for sli3 and sli4
adapters, but mandates the admin, via module parameter, specifically
identify which adapters the resets are to be removed for. Additionally,
bus_reset, which sends Target Reset TMFs to all targets, is also removed
from the template as it too has the same effect as the adapter reset.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
previous code did little more than log a message.
This patch adds abort path support, modeled after the SCSI code paths.
Currently addresses only the initiator path. Target path under
development, but stubbed out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
nvme bufs get allocated even when the registration fails.
Move allocation into the rsgistration success path.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For both initiator and target: if WQ is full, return -EBUSY.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Word 1 in NVME CMD IU appears byte swapped from value placed in WQE
Should be Big Endian value in WQE word 16
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME LS requests and responses had wrong R_CTL values.
Use the FC4 ELS Request and Response defines (defines badly
named, they are FC4 LS's) instead of the base ELS values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
if REG_VPI fails, the driver was incorrectly issuing INIT_VFI
(a SLI4 command) on a SLI3 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From: Colin Ian King <colin.king@canonical.com>
In the case where sglq is null, the current code just returns without
unlocking the spinlock sql_list_lock. Fix this by breaking out of the
while loop and the exit path will then unlock and return NULL as was
the original intention.
Detected by CoverityScan, CID#1411635 ("Missing unlock")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From: Colin Ian King <colin.king@canonical.com>
dma_buf->iocbq is being dereferenced immediately before it is
being null checked, so we have a potential null pointer dereference
bug. Fix this by only dereferencing it only once we have passed
a null check on the pointer.
Detected by CoverityScan, CID#1411652 ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From: Colin Ian King <colin.king@canonical.com>
The sanity check for hrq should be moved to before the deference
of hrq to ensure we don't perform a null pointer deference.
Detected by CoverityScan, CID#1411650 ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From: Colin Ian King <colin.king@canonical.com>
In the NVMET_FCOP_RSP case, sgel is assigned but never used and
hence is redundant and can be removed.
Detected by CoverityScan, CID#1411658 ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch shortens every init_timer in lpfc module followed by function
and data assignment using setup_timer. This is purely cleanup patch, it
does not add new functionality nor remove any existing functionality.
An init_timer call in this form:
init_timer(&vport->fc_disctmo);
vport->fc_disctmo.function = lpfc_disc_timeout;
vport->fc_disctmo.data = vport;
is shortened to:
setup_timer(&vport->fc_disctmo, lpfc_disc_timeout, vport);
It increases readability and reduces chances of mistakes done by
developers.
Signed-off-by: Tomas Jasek <tomsik68@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using %llx for a dma_addr_t can lead to format/argument mismatches. Use
%pad and the address of the dma_addr_t instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add __printf compiler verification of format and arguments. Fix
fallout.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It returns the number of vectors allocated when successful, so check for
a negative error only.
Fixes: 2e48e349 ("scsi: vmw_pvscsi: switch to pci_alloc_irq_vectors")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Loïc Yhuel <loic.yhuel@gmail.com>
Tested-by: Loïc Yhuel <loic.yhuel@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Recent printk changes for KERN_CONT cause this logging to be defectively
emitted on multiple lines. Fix it.
Also reduces object size a trivial amount.
$ size drivers/scsi/qla2xxx/qla_dbg.o*
text data bss dec hex filename
39125 0 0 39125 98d5 drivers/scsi/qla2xxx/qla_dbg.o.new
39164 0 0 39164 98fc drivers/scsi/qla2xxx/qla_dbg.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return status of the adapter check on KERNEL_PANIC is supposed to be
the upper 16 bits of the OMR status register.
Fixes: c421530bf8 (scsi: aacraid: Reorder Adpater status check)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without CONFIG_DEBUG_FS, we run into a link error:
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_poll':
qedi_iscsi.c:(.text.qedi_ep_poll+0x134): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_disconnect':
qedi_iscsi.c:(.text.qedi_ep_disconnect+0x36c): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_connect':
qedi_iscsi.c:(.text.qedi_ep_connect+0x350): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_fw.o: In function `qedi_tmf_work':
qedi_fw.c:(.text.qedi_tmf_work+0x3b4): undefined reference to `do_not_recover'
This defines the symbol as a constant in this case, as there is no way to
set it to anything other than zero without DEBUG_FS. In addition, I'm renaming
it to qedi_do_not_recover in order to put it into a driver specific namespace,
as "do_not_recover" is a really bad name for a kernel-wide global identifier
when it is used only in one driver.
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did. The new stuff is basically lpfc
(nvme), qedi and aacraid. The fixes cover a lot of previously
submitted stuff, the most important of which probably covers some of
the failing irq vectors allocation and other fallout from having the
SCSI command allocated as part of the block allocation functions.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=e+6v
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did.
The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
cover a lot of previously submitted stuff, the most important of which
probably covers some of the failing irq vectors allocation and other
fallout from having the SCSI command allocated as part of the block
allocation functions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
scsi: qedi: Fix memory leak in tmf response processing.
scsi: aacraid: remove redundant zero check on ret
scsi: lpfc: use proper format string for dma_addr_t
scsi: lpfc: use div_u64 for 64-bit division
scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
scsi: cciss: correct check map error.
scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
scsi: aacraid: Fixed expander hotplug for SMART family
scsi: mpt3sas: switch to pci_alloc_irq_vectors
scsi: qedf: fixup compilation warning about atomic_t usage
scsi: remove scsi_execute_req_flags
scsi: merge __scsi_execute into scsi_execute
scsi: simplify scsi_execute_req_flags
scsi: make the sense header argument to scsi_test_unit_ready mandatory
scsi: sd: improve TUR handling in sd_check_events
scsi: always zero sshdr in scsi_normalize_sense
scsi: scsi_dh_emc: return success in clariion_std_inquiry()
scsi: fix memory leak of sdpk on when gd fails to allocate
scsi: sd: make sd_devt_release() static
scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
...
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- enable dual mode (initiator + target) qla2xxx operation. (Quinn +
Himanshu)
- add a framework for qla2xxx async fabric discovery. (Quinn +
Himanshu)
- enable iscsi PDU DDP completion offload in cxgbit/T6 NICs. (Varun)
- fix target-core handling of aborted failed commands. (Bart)
- fix a long standing target-core issue NULL pointer dereference with
active I/O LUN shutdown. (Rob Millner + Bryant + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
target: Add counters for ABORT_TASK success + failure
iscsi-target: Fix early login failure statistics misses
target: Fix NULL dereference during LUN lookup + active I/O shutdown
target: Delete tmr from list before processing
target: Fix handling of aborted failed commands
uapi: fix linux/target_core_user.h userspace compilation errors
target: export protocol identifier
qla2xxx: Fix a warning reported by the "smatch" static checker
target/iscsi: Fix unsolicited data seq_end_offset calculation
target/cxgbit: add T6 iSCSI DDP completion feature
target/cxgbit: Enable DDP for T6 only if data sequence and pdu are in order
target/cxgbit: Use T6 specific macros to get ETH/IP hdr len
target/cxgbit: use cxgb4_tp_smt_idx() to get smt idx
target/iscsi: split iscsit_check_dataout_hdr()
target: Remove command flag CMD_T_DEV_ACTIVE
target: Remove command flag CMD_T_BUSY
target: Move session check from target_put_sess_cmd() into target_release_cmd_kref()
target: Inline transport_cmd_check_stop()
target: Remove an overly chatty debug message
target: Stop execution if CMD_T_STOP has been set
...
Looks like a quiet cycle for vhost/virtio, just a couple of minor
tweaks. Most notable is automatic interrupt affinity for blk and scsi.
Hopefully other devices are not far behind.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYt1rRAAoJECgfDbjSjVRpEZsIALSHevdXWtRHBZUb0ZkqPLQb
/x2Vn49CcALS1p7iSuP9L027MPeaLKyr0NBT9hptBChp/4b9lnZWyyAo6vYQrzfx
Ia/hLBYsK4ml6lEwbyfLwqkF2cmYCrZhBSVAILifn84lTPoN7CT0PlYDfA+OCaNR
geo75qF8KR+AUO0aqchwMRL3RV3OxZKxQr2AR6LttCuhiBgnV3Xqxffg/M3x6ONM
0ffFFdodm6slem3hIEiGUMwKj4NKQhcOleV+y0fVBzWfLQG9210pZbQyRBRikIL0
7IsaarpaUr7OrLAZFMGF6nJnyRAaRrt6WknTHZkyvyggrePrGcmGgPm4jrODwY4=
=2zwv
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vhost updates from Michael Tsirkin:
"virtio, vhost: optimizations, fixes
Looks like a quiet cycle for vhost/virtio, just a couple of minor
tweaks. Most notable is automatic interrupt affinity for blk and scsi.
Hopefully other devices are not far behind"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-console: avoid DMA from stack
vhost: introduce O(1) vq metadata cache
virtio_scsi: use virtio IRQ affinity
virtio_blk: use virtio IRQ affinity
blk-mq: provide a default queue mapping for virtio device
virtio: provide a method to get the IRQ affinity mask for a virtqueue
virtio: allow drivers to request IRQ affinity when creating VQs
virtio_pci: simplify MSI-X setup
virtio_pci: don't duplicate the msix_enable flag in struct pci_dev
virtio_pci: use shared interrupts for virtqueues
virtio_pci: remove struct virtio_pci_vq_info
vhost: try avoiding avail index access when getting descriptor
virtio_mmio: expose header to userspace
We don't actually need the full rculist.h header in sched.h anymore,
we will be able to include the smaller rcupdate.h header instead.
But first update code that relied on the implicit header inclusion.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 669f044170 ("scsi: srp_transport: Move queuecommand() wait code
to SCSI core") can make scsi_internal_device_block() sleep. However,
the mpt3sas driver can call this function from an interrupt
handler. Hence add a second argument to scsi_internal_device_block()
that restores the old behavior of this function for the mpt3sas handler.
The call chain that triggered an "IRQ handler enabled interrupts"
complaint is as follows:
_base_interrupt()
-> _base_async_event()
-> mpt3sas_scsih_event_callback()
-> _scsih_check_topo_delete_events()
-> _scsih_block_io_to_children_attached_directly()
-> _scsih_block_io_device()
-> _scsih_internal_device_block()
-> scsi_internal_device_block()
Reported-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Omar Sandoval <osandov@osandov.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: <stable@vger.kernel.org> # v4.10+
Tested-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit <f2e767bb5d6e> ("mpt3sas: Force request partial completion
alignment") was not considering the case of commands not operating on
logical block size units (e.g. REQ_OP_ZONE_REPORT and its 64B aligned
partial replies). In this case, forcing alignment of resid to the device
logical block size can break the command result, e.g. in the case of
REQ_OP_ZONE_REPORT, the exact number of zone reported by the device.
Move the partial completion alignement check of mpt3sas to a generic
implementation in sd_done(). The check is added within the default
section of the initial req_op() switch case so that the report and reset
zone commands are ignored. In addition, as sd_done() is not called for
passthrough requests, resid corrections are not done as intended by the
initial mpt3sas patch.
Fixes: f2e767bb5d ("mpt3sas: Force request partial completion alignment")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since in UFS 2.1 specification some of the descriptor lengths differs
from 2.0 specification and some devices, which are reporting spec
version 2.0 have different descriptor lengths we can not rely on
hardcoded values taken from 2.0 specification. This patch introduces
reading these lengths per each device from descriptor headers at probe
time to ensure their correctness.
Signed-off-by: Michal' Potomski <michalx.potomski@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There's a rather long standing regression from the commit "libiscsi:
Reduce locking contention in fast path"
Depending on iSCSI target behavior, it's possible to hit the case in
iscsi_complete_task where the task is still on a pending list
(!list_empty(&task->running)). When that happens the task is removed
from the list while holding the session back_lock, but other task list
modification occur under the frwd_lock. That leads to linked list
corruption and eventually a panicked system.
Rather than back out the session lock split entirely, in order to try
and keep some of the performance gains this patch adds another lock to
maintain the task lists integrity.
Major enterprise supported kernels have been backing out the lock split
for while now, thanks to the efforts at IBM where a lab setup has the
most reliable reproducer I've seen on this issue. This patch has been
tested there successfully.
Signed-off-by: Chris Leech <cleech@redhat.com>
Fixes: 659743b02c ("[SCSI] libiscsi: Reduce locking contention in fast path")
Reported-by: Prashantha Subbarao <psubbara@us.ibm.com>
Reviewed-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The call to qedi_setup_int is not updating the return code rc yet rc is
being checked for an error. Fix this by assigning rc to the return code
from the call to qedi_setup_int.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The check for ret being zero is redundant as a few statements earlier we
break out of the while loop if ret is non-zero. Thus we can remove the
zero check and also the dead-code non-zero case too.
Detected by CoverityScan, CID#1411632 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
dma_addr_t may be either u32 or u64, depending on the kernel configuration,
and we get a warning for the 32-bit case:
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_nvme_ls_req':
drivers/scsi/lpfc/lpfc_logmsg.h:52:52: error: format '%llu' expects argument of type 'long long unsigned int', but argument 11 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]
drivers/scsi/lpfc/lpfc_logmsg.h:52:52: error: format '%llu' expects argument of type 'long long unsigned int', but argument 12 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_nvme_ls_abort':
drivers/scsi/lpfc/lpfc_logmsg.h:52:52: error: format '%llu' expects argument of type 'long long unsigned int', but argument 11 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]
drivers/scsi/lpfc/lpfc_logmsg.h:52:52: error: format '%llu' expects argument of type 'long long unsigned int', but argument 12 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]
printk has a special "%pad" format string that passes the dma address by
reference to solve this problem.
Fixes: 01649561a8 ("scsi: lpfc: NVME Initiator: bind to nvme_fc api")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The new debugfs output causes a link error on 32-bit architectures:
ERROR: "__aeabi_uldivmod" [drivers/scsi/lpfc/lpfc.ko] undefined!
This code is not performance critical, so we can simply use div_u64().
[mkp: fixed up whitespace]
Fixes: bd2cdd5e40 ("scsi: lpfc: NVME Initiator: Add debugfs support")
Fixes: 2b65e18202 ("scsi: lpfc: NVME Target: Add debugfs support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
therfore||therefore
Besides, tidy up comment blocks for 80-col wrapping.
Link: http://lkml.kernel.org/r/1481573103-11329-31-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
overwritting||overwriting
Link: http://lkml.kernel.org/r/1481573103-11329-29-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
omited||omitted
omiting||omitting
Link: http://lkml.kernel.org/r/1481573103-11329-26-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
comsume||consume
comsumer||consumer
comsuming||consuming
I see some variable names with this pattern, but this commit is only
touching comment blocks to avoid unexpected impact.
Link: http://lkml.kernel.org/r/1481573103-11329-19-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
intialization||initialization
The "inintialization" in drivers/acpi/spcr.c is a different pattern but
I fixed it as well in this commit.
Link: http://lkml.kernel.org/r/1481573103-11329-16-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
embeded||embedded
Link: http://lkml.kernel.org/r/1481573103-11329-12-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
aligment||alignment
I did not touch the "N_BYTE_ALIGMENT" macro in
drivers/net/wireless/realtek/rtlwifi/wifi.h to avoid unpredictable
impact.
I fixed "_aligment_handler" in arch/openrisc/kernel/entry.S because
it is surrounded by #if 0 ... #endif. It is surely safe and I
confirmed "_alignment_handler" is correct.
I also fixed the "controler" I found in the same hunk in
arch/openrisc/kernel/head.S.
Link: http://lkml.kernel.org/r/1481573103-11329-8-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
an user||a user
an userspace||a userspace
I also added "userspace" to the list since it is a common word in Linux.
I found some instances for "an userfaultfd", but I did not add it to the
list. I felt it is endless to find words that start with "user" such as
"userland" etc., so must draw a line somewhere.
Link: http://lkml.kernel.org/r/1481573103-11329-4-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use automatic IRQ affinity assignment in the virtio layer if available,
and build the blk-mq queues based on it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a struct irq_affinity pointer to the find_vqs methods, which if set
is used to tell the PCI layer to create the MSI-X vectors for our I/O
virtqueues with the proper affinity from the start. Compared to after
the fact affinity hints this gives us an instantly working setup and
allows to allocate the irq descritors node-local and avoid interconnect
traffic. Last but not least this will allow blk-mq queues are created
based on the interrupt affinity for storage drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Merge more updates from Andrew Morton:
- almost all of the rest of MM
- misc bits
- KASAN updates
- procfs
- lib/ updates
- checkpatch updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (124 commits)
checkpatch: remove false unbalanced braces warning
checkpatch: notice unbalanced else braces in a patch
checkpatch: add another old address for the FSF
checkpatch: update $logFunctions
checkpatch: warn on logging continuations
checkpatch: warn on embedded function names
lib/lz4: remove back-compat wrappers
fs/pstore: fs/squashfs: change usage of LZ4 to work with new LZ4 version
crypto: change LZ4 modules to work with new LZ4 module version
lib/decompress_unlz4: change module to work with new LZ4 module version
lib: update LZ4 compressor module
lib/test_sort.c: make it explicitly non-modular
lib: add CONFIG_TEST_SORT to enable self-test of sort()
rbtree: use designated initializers
linux/kernel.h: fix DIV_ROUND_CLOSEST to support negative divisors
lib/find_bit.c: micro-optimise find_next_*_bit
lib: add module support to atomic64 tests
lib: add module support to glob tests
lib: add module support to crc32 tests
kernel/ksysfs.c: add __ro_after_init to bin_attribute structure
...
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull block updates and fixes from Jens Axboe:
- NVMe updates and fixes that missed the first pull request. This
includes bug fixes, and support for autonomous power management.
- Fix from Christoph for missing clear of the request payload, causing
a problem with (at least) the storvsc driver.
- Further fixes for the queue/bdi life time issues from Jan.
- The Kconfig mq scheduler update from me.
- Fixing a use-after-free in dm-rq, spotted by Bart, introduced in this
merge window.
- Three fixes for nbd from Josef.
- Bug fix from Omar, fixing a bug in sas transport code that oopses
when bsg ioctls were used. From Omar.
- Improvements to the queue restart and tag wait from from Omar.
- Set of fixes for the sed/opal code from Scott.
- Three trivial patches to cciss from Tobin
* 'for-linus' of git://git.kernel.dk/linux-block: (41 commits)
dm-rq: don't dereference request payload after ending request
blk-mq-sched: separate mark hctx and queue restart operations
blk-mq: use sbq wait queues instead of restart for driver tags
block/sed-opal: Propagate original error message to userland.
nvme/pci: re-check security protocol support after reset
block/sed-opal: Introduce free_opal_dev to free the structure and clean up state
nvme: detect NVMe controller in recent MacBooks
nvme-rdma: add support for host_traddr
nvmet-rdma: Fix error handling
nvmet-rdma: use nvme cm status helper
nvme-rdma: move nvme cm status helper to .h file
nvme-fc: don't bother to validate ioccsz and iorcsz
nvme/pci: No special case for queue busy on IO
nvme/core: Fix race kicking freed request_queue
nvme/pci: Disable on removal when disconnected
nvme: Enable autonomous power state transitions
nvme: Add a quirk mechanism that uses identify_ctrl
nvme: make nvmf_register_transport require a create_ctrl callback
nvme: Use CNS as 8-bit field and avoid endianness conversion
nvme: add semicolon in nvme_command setting
...
The mac_scsi driver still gets disabled when SCSI=m. This should have
been fixed back when I enabled the tristate but I didn't see the bug.
Fixes: 6e9ae6d560 ("[PATCH] mac_scsi: Add module option to Kconfig")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in pr_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current driver Hotplug processing code skips over Enclosure channel,
therefore any addition/removal of expander enclosure is not processed.
Additionally device addition code relies on older device type, which
prevents the hotplug of adapter expanders.
Fixed by removing code that skips over Enclosure channels and using the
latest device type for addition or removal or enclosure expanders.
Fixes: 6223a39fe6 (scsi: aacraid: Added support for hotplug)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cleanup the MSI-X handling allowing us to use the PCI-layer provided
vector allocation.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on an original patch by Hannes Reinecke.
The driver didn't follow the atomic_t vs refcount_t change, and anyway
one should be using kref_read() instead of accessing the counter inside
an kref.
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.)
Cc: Hannes Reinecke <hare@suse.de>
Cc: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Dupuis, Chad <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
And switch all callers to use scsi_execute instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All but one caller want the decoded sense header, so offer the existing
__scsi_execute helper as the public scsi_execute API to simply the
callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a sshdr argument to __scsi_execute so that we can decode the sense
data directly into the sense header instead of needing a copy of it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's a tiny structure that can be allocated on the stack, don't
complicate the code by making it optional.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove bogus evaluations of retval and sshdr when the device is offline,
and fix a possible NULL pointer dereference by allocating the 8 byte
sized sense header on stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This gives us a clear state even if a command didn't return sense data.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We accidentally return an uninitialized variable on success.
Fixes: b6ff1b14cd ("[SCSI] scsi_dh: Update EMC handler")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an allocation failure of gd, the current exit path is via
out_free_devt which leaves sdpk still allocated and hence it gets
leaked. Fix this by correcting the order of resource free'ing with a
change in the error exit path labels.
Detected by CoverityScan, CID#1399519 ("Resource Leak")
Fixes: 0dba1314d4 ("scsi, block: fix duplicate bdi name registration crashes")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following sparse warning:
drivers/scsi/sd.c:3087:6: warning:
symbol 'sd_devt_release' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For target mode, we need to increase minimum vectors value by one to
account for ATIO queue.
Following stack trace will be seen
Call Trace:
qla24xx_config_rings+0x15a/0x230 [qla2xxx]
qla2x00_init_rings+0x1a1/0x3a0 [qla2xxx]
qla2x00_restart_isp+0x5c/0x120 [qla2xxx]
qla2x00_abort_isp+0x138/0x430 [qla2xxx]
? __schedule+0x260/0x580
qla2x00_do_dpc+0x3bc/0x920 [qla2xxx]
? qla2x00_relogin+0x290/0x290 [qla2xxx]
? schedule+0x3a/0xa0
? qla2x00_relogin+0x290/0x290 [qla2xxx]
kthread+0x103/0x140
? __kthread_init_worker+0x40/0x40
ret_from_fork+0x29/0x40
RIP: qlt_24xx_config_rings+0x6c/0x90
[mkp: fixed Fixes: hash]
Cc: <stable@vger.kernel.org>
Fixes: 17e5fc5858 ("scsi: qla2xxx: fix MSI-X vector affinity")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch cleaned up queue configuration code, such that once
initialized, we should not touch msix_count value. This will prevent
incorrect numbers of MSI-X vectors requested while performing target
mode configuration.
[mkp: fixed Fixes: hash]
Cc: <stable@vger.kernel.org>
Fixes: d74595278f ("scsi: qla2xxx: Add multiple queue pair functionality.")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add missing Kconfig NVME dependencies.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 11.2.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyrights to 2017 for all files touched in this patch set
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Add debugfs support
Adds debugfs snippets to cover the new NVME target functionality
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Tie in to NVME Fabrics nvmet_fc LLDD target api
Adds the routines to:
- register and deregister the FC port as a nvmet-fc targetport
- binding of nvme queues to adapter WQs
- receipt and passing of NVME LS's to transport, sending transport response
- receipt of NVME FCP CMD IUs, processing FCP target io data transmission
commands; transmission of FCP io response
- Abort operations for tgt io exchanges
[mkp: fixed space at end of file warning]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Merge into FC discovery
Adds NVME PRLI handling and Nameserver registrations for NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
