Commit Graph

28659 Commits

Author SHA1 Message Date
Sandeep Patil
1d4bab0824 [ARM] S3C24A0: Serial port definitions and driver support.
Add serial support for S3C24A0, based on current S3C2410
UART driver. It adds necessary new defines in regs-serial.h
for S3C24A0 and the code to support this device in
drivers/serial/s3c24a0.c

Signed-off-by: Sandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:36 +00:00
Ben Dooks
f0c9eb4ec2 [ARM] S3C24A0: Debug macro definitions
Add the necessary debug macros for the S3C24A0 to enable
kernel debugging, and fix a bug with selecting the wrong
default debug implementation from the base include.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:33 +00:00
Sandeep Patil
f1cb9eba5b [ARM] S3C24A0: Correct S3C2410_PA_GPIO in S3C24XX_VA_GPIO
The definition of S3C24XX_VA_GPIO used S3C2410_PA_GPIO
where it should have read S3C24XX_PA_GPIO.

Signed-off-by: Sandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:31 +00:00
Sandeep Patil
ddbf5654b4 [ARM] S3C24A0: arch/arm/mach-s3c24a0/include/mach header files
Add initial arch/arm/mach-s3c24a0/include/mach header
files for supporting Samsung S3C24A0 SoC.

Signed-off-by: Sandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:28 +00:00
Ben Dooks
7d2dbcf9fa [ARM] S3C: Fix scaler1 clock rate information
The pwm-scaler0 and pwm-scaler1 clocks have their
.id field set to -1 as they are not referenced to
any specific device. However, parts of the pwm-clock
code used the .id field to identify which scaler
clock was being used.

Fix the problem by comparing against the pointer to
the clock to identify the scalers.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:25 +00:00
Ben Dooks
82fd8e681d [ARM] S3C: Add set_rate/round_rate methods for pwm-scaler clock
Add the set_rate and round_rate methods for the pwm-scaler
clock for use with the time code.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:24 +00:00
Ben Dooks
f2edc7565a [ARM] S3C24XX: Reduce code lineage of gpiolib.c
All the s3c24xx gpiolib chips share the same get/set
calls and all but one bank shares the same calls for
.direction_input and .direction_output methods.

Change the initialisation process to use an new call
to register the chips that fills in any blank calls
with the default values to avoid having to fill them
in the structure initialisers.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:24 +00:00
Ben Dooks
cec444b790 [ARM] S3C: BUG_ON() if clock has already been registered
Add a simple check when registering a clock on whether
the clock has already been added to the list.

Any attempt to re-register a clock will cause the
clock list to be come looped and thus produces silent
failures when looking up clocks.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:22 +00:00
Ben Dooks
93b458858f [ARM] S3C: Move pwm-clock.c to arch/arm/plat-s3c
Move pwm-clock.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:20 +00:00
Ben Dooks
adbefaa5fd [ARM] S3C: Move core clock support to plat-s3c
Move the core clock registration and definitions
in arch/arm/plat-s3c24xx/clock.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:18 +00:00
Ben Dooks
b915a12511 [ARM] S3C: Move time.c to arch/arm/plat-s3c
Move time.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:15 +00:00
Ben Dooks
6af0e929e9 [ARM] S3C: Move S3C2410_EXTINT to common regs-irqtype.h header
Add a common include file (regs-irqtype.h) for the IRQ
trigger control register values S3C2410_EXTINT*.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:13 +00:00
Ben Dooks
a503059c14 [ARM] S3C24XX: Move headers from plat-s3c24xx to plat-s3c
Move clock.h, cpu.h and devs.h to plat-s3c for use
with the s3c64xx support.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:10 +00:00
Ben Dooks
e425382ed9 [ARM] S3C24XX: Update clock data on resume
Update the clock settings on resume for suspend/resume
support so that if the boot loader changes anything or
the system's PLL is reset then we return with the correct
settings.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:08 +00:00
Ben Dooks
c3391e36d6 [ARM] S3C24XX: Change clock locking to use spinlocks.
We cannot sleep if we have cpufreq pm enabled during some
of the clock operations, so change to use a spinlock to
protect the clock system.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:07 +00:00
Ben Dooks
e24b864ab3 [ARM] S3C24XX: Split pll code out of regs-clock.h
Move the PLL calculation code into it's own header
file for re-use with the other plat-s3c24xx based
systems such as the S3C24A0.

Note, we change the name of s3c2410_get_pll to the
more generically named s3c24xx_get_pll as well as
the related defintions.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:02 +00:00
Ben Dooks
93bc6b6371 [ARM] S3C24XX: Split DCLK/CLKOUT definitions out of clock.c
Only certain boards need these clocks, and they are not
available on some CPUs (such as the S3C24A0) so remove
them from arch/arm/plat-s3c24xx/clock.c and into their
own file with appropriate Kconfig entries.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:46:00 +00:00
Ben Dooks
74b265d4e0 [ARM] S3C24XX: Move initialisation code to arch/arm/plat-s3c
We need to add plat-s3c to the build to get the headers
that will go in here once moved from include/asm-arm so
we may as well put some useful common s3c code in here
to stop the errors generated form having nothing built.

The cpu setup is now passed the cpu idcode and the table
of supported cpus to s3c_init_cpu() to abstract the
cpu identification out of the initial io setup.

As well as moving the cpu initialisation code, we move the
map of the board specific items up to the calling code as
none of the map_io() functions actually do anything other
than pass this to iotable_init().

This patch does not rename any of the init functions that
will be common to s3c24xx and any other s3c architectures
as this can be done at a later date as it will touch all
the board support files which use functions such as
s3c24xx_init_clocks() and s3c24xx_init_uarts().

Note, the header arch/arm/plat-s3c24xx/include/plat/cpu.h
still has functions that are used by both the cpu and
board initialisation functions. This means that each board
has definitions specific to the cpu support included and
the vice-versa.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:45:57 +00:00
Ben Dooks
2cd493fc10 [ARM] S3C24XX: Add default <mach/io.h> header
Add a default header for <mach/io.h> for systems
such as the S3C24A0 which do not need any of the
complex code that the S3C2410 uses.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:45:55 +00:00
Ben Dooks
112f4a708d [ARM] S3C24XX: Move vmalloc.h to plat-s3c
vmalloc.h is common across all the current s3c platforms,
so move it to arch/arm/plat-s3c/include/mach to be used
for all the targets.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:45:52 +00:00
Ben Dooks
95f42b3911 [ARM] S3C: Make <mach/timex.h> common
Move <mach/timex.h> to arch/arm/plat-s3c/include/mach/timex.h
so it can be the default for all S3C based architectures.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:45:50 +00:00
Ben Dooks
1b3ba68884 [ARM] S3C2410: Move base clock code to plat-s3c24xx
Move the S3C2410 base clock list to arch/arm/plat-s3c24xx
as this code is common to the S3C2410, S3C2440 and S3C2442
cpus.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:45:47 +00:00
Ben Dooks
7f565ecc33 [ARM] S3C: Add <plat/cpu-freq.h> for initial cpufreq definitions
This is the header file that defines the basic cpu frequency
scalling support for the Samsung S3C series of SoC.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:45:45 +00:00
Ben Dooks
b2a6cf3b1e [ARM] S3C24XX: Default SPI pin configuration for SPI
Add a set of default pin configuration routines for
setting up the SPI gpio configuration when using the
hardware SPI driver.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15 21:45:42 +00:00
Russell King
72aaf09fda Merge git://git.marvell.com/orion into devel 2008-12-13 09:12:51 +00:00
Russell King
67fbc23123 [ARM] fix xm_x2xx_defconfig build errors
drivers/built-in.o: In function `pci_set_consistent_dma_mask':
hid-quirks.c:(.text+0x2664): multiple definition of `pci_set_consistent_dma_mask'
drivers/built-in.o: In function `pci_set_dma_mask':
hid-quirks.c:(.text+0x42c4): multiple definition of `pci_set_dma_mask'

because drivers/pci/pci.c was not seeing the definition disabling these
functions.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-13 09:12:09 +00:00
Hartley Sweeten
3e7a728117 [ARM] 5343/1: ep93xx: include linux/i2c.h
Include <linux/i2c.h> in all ep93xx platforms.

Patch "5311/1: add core support for built in i2c bus" will cause build errors due to the following in
arch/arm/mach-ep93xx/include/mach/platform.h:

+void ep93xx_register_i2c(struct i2c_board_info *devices, int num);

The i2c.h header needs to be included in order to define struct i2c_board_info.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-13 09:12:09 +00:00
Hartley Sweeten
e48f3fa373 [ARM] 5342/1: ep93xx: platform init cleanup
Use EP93XX_*_PHYS_BASE and SZ_* defines in ep93xx platform inits.

The following patch changes the flash memory hard-coded resource
addresses and MACHINE_START boot_params to EP93XX_*_PHYS_BASE and
SZ_* defines to improve readability. Also some minor whitespace
cleanup resulting from previous patches.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-13 09:12:08 +00:00
Jaya Kumar
854feaede5 [ARM] 5337/1: gumstix: move am200 specific gpio pins into am200epd.
The gpio setup for AM200 specific GPIO pins should be done in the AM200
code rather than in generic gumstix code.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-13 09:12:08 +00:00
Russell King
1124d6d21f [ARM] dma: correct dma_supported() implementation
dma_supported() is supposed to indicate whether the system can support
the DMA mask it was passed, which depends on the maximal address which
can be returned for DMA allocations.  If the mask is smaller than that,
we are unable to guarantee that the driver can reliably obtain suitable
memory.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-13 09:12:07 +00:00
Russell King
70d13e083c [ARM] netwinder: clean up GPIO naming
Netwinder was using gpio_xxx names which could clash with the GPIO
layer.  Add a 'nw_' prefix to ensure that these remain separate.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-13 09:12:07 +00:00
Nicolas Pitre
58c2467355 [ARM] Kirkwood: update defconfig
Signed-off-by: Nicolas Pitre <nico@marvell.com>
2008-12-11 16:39:09 -05:00
Nicolas Pitre
b71b9effb5 [ARM] Feroceon: pass proper -mtune argument to gcc
Compilation for the Feroceon core should use -mtune=marvell-f.  This is
available in Code Sourcery's 2008Q3 release at the moment. Otherwise
fall back to -mtune-=xscale.

Signed-off-by: Nicolas Pitre <nico@marvell.com>
2008-12-11 16:39:09 -05:00
Ronen Shitrit
37787e449b [ARM] Kirkwood: properly handle the WAN port on newer RD88F6281 boards
On newer versions of the RD88F6281 board, the WAN port is connected to
its own ethernet port on the CPU, via a separate PHY, whereas on older
versions of the board, it is connected to one of the PHYs in the
ethernet switch.  In the RD8F6281 setup code, detect which version of
the board we are running on, and instantiate the ethernet ports and
switch driver accordingly.

Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
2008-12-11 16:39:08 -05:00
Ronen Shitrit
d15fb9efe9 [ARM] Kirkwood: allow instantiating the second ethernet port
The 88f6192 and 88f6281 Kirkwood SoCs support two ethernet ports.
Add the platform glue that will allow board support files to
instantiate the second ethernet port.

Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
2008-12-11 16:39:08 -05:00
Matt Palmer
f93e4159b1 [ARM] DNS323: Initialise 88F5182 correctly
The 88F5182 found in the DNS-323 rev B1 (and some other devices, such
as the CH3SNAS) require different initialisation of the SATA
controller and MPP registers.

Tested on a DNS-323 rev B1.

Signed-off-by: Matt Palmer <mpalmer@hezmatt.org>
2008-12-11 16:38:56 -05:00
Matt Palmer
a93f44c175 [ARM] DNS323: Read MAC address from flash
Based on similar code from the tsx09 series of machines, just rips the MAC
address out of flash and stuffs it into the NIC. Tested on a DNS323 rev B1.
It's possible (though unlikely) that an A1 will have the MAC in a different
location in flash.

Signed-off-by: Matt Palmer <mpalmer@hezmatt.org>
2008-12-11 16:36:59 -05:00
Ronen Shitrit
fb6f552930 [ARM] Orion: add the option to support different ehci phy initialization
The Orion ehci driver serves the Orion, kirkwood and DD Soc families.
Since each of those integrate a different USB phy we should have the
ability to use few initialization sequences or to leave the boot loader
phy settings as is.

Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
2008-12-04 01:28:14 -05:00
wanzongshun
7ec80ddf04 [ARM] 5338/1: Add Nuvoton W90P910 Platform support
Add Nuvoton W90X900 ARM9 plat support to linux arm tree,
Now, this patch include only W90P910 EVB of W90P910 CPU,
Its driver is nothing.

Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-03 21:57:16 +00:00
Russell King
c5b84b3bb0 Merge branch 'for-rmk' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel
Conflicts:

	arch/arm/mach-pxa/pxa25x.c
2008-12-02 22:07:40 +00:00
Anton Vorontsov
bc2fd1c09c [ARM] pxa: add basic support for HP iPAQ h5000
This patch adds HP iPAQ h5000's (h5400, h5500) basic definitions.

Kernel will able to boot, work via serial console, mount filesystems
placed on flashes and run USB gadgets (g_ether by default).

Other device drivers (frame buffer, LCD, touchscreen, backlight,
bluetooth, w1/battery, ...) are depend on SAMCOP and MediaQ
SoCs/MFDs, drivers to which will be submitted too, after massive
cleanups.

This machine will be used as "real user" for these new drivers.

This is an updated version of the patch, which contains fixes proposed on
linux-arm-kernel mailing list.

Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Milan Plzik <milan.plzik@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:50 +08:00
Dmitry Baryshkov
431a2cff07 [ARM] pxa/poodle: add physmap mapping for ROM
Add mapping for system ROM using physmap-flash mapping.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:49 +08:00
Dmitry Baryshkov
4a9295ccb4 [ARM] pxa/corgi: add physmap mapping for ROM
Add mapping for system ROM using physmap-flash mapping.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:49 +08:00
Dmitry Baryshkov
e5d3bf3c10 [ARM] pxa/spitz: add physmap mapping for ROM
Add mapping for system ROM using physmap-flash mapping.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:49 +08:00
Dmitry Baryshkov
f34ee79a53 [ARM] pxa/tosa: add physmap mapping for ROM
Add mapping for system ROM using physmap-flash mapping.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:49 +08:00
Dmitry Baryshkov
ddfb33c0ff [ARM] pxa/tosa: fix building w/o TC6393XB driver
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:49 +08:00
Dmitry Baryshkov
31c9b284ae [ARM] pxa/tosa: support tc6393xb/tmiofb.
Add platform data necessary to support tmiofb on tosa.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:48 +08:00
Robert Jarzmik
4aa89f973f [ARM] pxa/MioA701: improve power supply sources
Take advantage of the newly created wm97xx battery driver
and remove useless code in mioa701 board code. Add also the
ac connection detect capability after the matching gpio was
discovered.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:48 +08:00
Robert Jarzmik
c96763d4dc [ARM] pxa/MioA701: discovered new gpio definitions.
The charger enable gpio is straight (1 means draw from USB
Vbus, 0 mean do not draw). The USB Vbus sensing is inverted
(1 means no Vbus voltage sensed, 0 means Vbus voltage
present).

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:48 +08:00
Robert Jarzmik
a0361a8afe [ARM] pxa/MioA701: change reset function to preserve RTC.
Change the halt and reboot method from gpio based to "jump
to ROM IPL beginning". This gives control back to IPL, which
without PowerOn key pressed, will put the device into deep
sleep until PowerOn is pressed for 1 second.

But this has the benefit of keeping the RTC registers across
reboots, which is good for OS change.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:48 +08:00
Robert Jarzmik
8e7ccddf0f [ARM] pxa/MioA701: add camera support for Mio A701 board.
Add GPIO configuration and platform specific declarations
to make Mitac Mio A701 camera chip work. The chip is a
Micron MT9M111 CMOS sensor, based on PXA QIF interface and
I2C bus for sensor control.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:48 +08:00
Robert Jarzmik
0bcd30ec8d [ARM] pxa/MioA701: remove KConfig leds driver requirement
Since mioa701 board has migrated to the mfp architecture,
low power gpio setup is now correctly handled even when gpio
led driver is not loaded, and leds and vibrator don't stay
activated in suspend mode (especially vibrator).

Remove the not needed anymore dependency.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:47 +08:00
Robert Jarzmik
724931465c [ARM] pxa: add resources for incoming rtc-pxa driver
Add IO memory and IRQ ressources for pxa based SoC to be
able to use the new rtc-pxa driver.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:47 +08:00
Philipp Zabel
a10c287d39 [ARM] pxa: cpufreq-pxa2xx: sdram_rows detection support
This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:47 +08:00
Marc Zyngier
65587f7d15 [ARM] pxa: cpufreq-pxa2xx: allow frequency table selection
Following the removal of the "->policy" usage for PXA255 in patch
459fc208ab (cpufreq: remove
policy->governor setting in drivers initialization), this patch
introduces an option (called "pxa255_turbo_table") to select either
the "run" or "turbo" frequency table.

It also cures the runtime warning that was printed each time the
frequency was changed.

Got rid of all references to CPUFREQ_POLICY_* for pxa255, and sticked
with the run/turbo thing.

Tested on an Arcom/Eurotech Viper.

Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:47 +08:00
Eric Miao
9179825cf5 [ARM] locomo: export locomo_frontlight_set()
This symbol is required by locomo backlight driver, exporting this
allows the driver to be built as a module.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:43:35 +08:00
Eric Miao
8cc7890981 [ARM] pxa: add missing GPIOs definitions
GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN
bit, add their definitions here with comments.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
2008-12-02 14:42:41 +08:00
Eric Miao
59c7bcd4d6 [ARM] pxa: add base PXA935 support due to CPUID change
PXA935 has changed its implementor ID from Intel to Marvell, this
patch modifies arch/arm/boot/compressed/head.S and proc-xsc3.S to
support a smooth bootup.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:40 +08:00
Eric Miao
f1c6cd62cc [ARM] pxa: introduced cpu_is_pxa935() and cpu_is_pxa9xx()
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:40 +08:00
Eric Miao
6f584cfab4 [ARM] pxa: move I2C pin configurations out into board specific files
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:40 +08:00
Eric Miao
1475822052 [ARM] pxa: register Power I2C device only when necessary
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:40 +08:00
Eric Miao
994642934d [ARM] pxa: move power I2C device definitions into devices.c
Let's put these devices into a central place even if they are now
processor specific, as they might be re-used in later processors.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:40 +08:00
Eric Miao
e8a5ab1f73 [ARM] pxa: remove unnecessary #include of pxa2xx-gpio.h in clock.c
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:39 +08:00
Eric Miao
7e5abc465b [ARM] pxa: include <mach/hardware.h> in pxa-regs.h
for the reference of __REG() within <mach/hardware.h>

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:39 +08:00
Eric Miao
bf8b38654b [ARM] pxa: further cleanup of pxa-regs.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:39 +08:00
Eric Miao
f1647e4c06 [ARM] pxa: move GPIOx_BASE and GPIO register offsets to gpio.c
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:39 +08:00
Eric Miao
1f017a9964 [ARM] pxa: move AC97 register definitions into dedicated regs-ac97.h
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:39 +08:00
Eric Miao
02f652626a [ARM] pxa: move UART register definitions into dedicated regs-uart.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:38 +08:00
Eric Miao
b31eca4f00 [ARM] pxa: move pxa2xx specific PWRMODE definitions into pxa2xx-regs.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:38 +08:00
Eric Miao
a07efb5dac [ARM] pxa: remove the now unused IMPMCR/IMPMSR register definitions
There two are internal registers that are used to control the power
management of the Internal Memory (i.e. Internal SRAM). They are
referenced nowhere and removed here to simplify pxa-regs.h a bit.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:38 +08:00
Eric Miao
d15313e685 [ARM] pxa: remove unused PWM register definitions, use generic PWM API
We now have generic PWM API for PXA, the PWM registers definitions are
now used nowhere, and it is not encouraged to manipulate them directly
by driver code.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:38 +08:00
Eric Miao
b40ddf5758 [ARM] pxa: move FICP register definitions into pxaficp_ir.c
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:38 +08:00
Eric Miao
013132cae8 [ARM] pxa: move camera (QCI) registers definition out of pxa-regs.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
2008-12-02 14:42:37 +08:00
Eric Miao
63e6552f7c [ARM] pxa: removed unused declarations of pxa_gpio_* in hardware.h
pxa_gpio_{get,set}_value() are not used anymore, remove them from hardware.h.
Declaration of pxa_gpio_mode() is still being referenced and thus moved into
pxa2xx-gpio.h

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:37 +08:00
Eric Miao
80796f2a40 [ARM] pxa: use <linux/gpio.h> instead of unnecessary <mach/gpio.h>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:37 +08:00
Eric Miao
067455aa53 [ARM] pxa: add support for additional GPIOs on PXA26x
Original patch from Marek Vasut, the problems with PXA26x are:

1. there are additional 4 GPIOs 86,87,88,89 have their direction bits
   inverted in GPDR2, as well as their alternate function bits being
   '1' for their GPIO functionality in GAFRx

2. there is no easy way to decide if the processor is a pxa26x or a
   pxa250/pxa255 at run-time, so the assumption here is the pxa26x
   will be treated as one of the pxa25x variants, and board code
   should have a better knowledge of the processor it is featured

Introduce pxa26x_init_irq() for the second purpose, and treat the
additional GPIOs > 85 on PXA25x specially.

Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code
a bit when PXA26x support isn't needed. Board config options have
to select this to enable the support for PXA26x.

__gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x
isn't selected.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:37 +08:00
Eric Miao
e88db8b91f Revert "[ARM] pxa: introduce cpu_is_pxa26x()"
This reverts commit da1a3dc0eb.

The originally proposed way in the above commit is incorrect. And
there is no easy way to distinguish between pxa25x and pxa26x at
run-time.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:37 +08:00
Eric Miao
ddd244dd81 [ARM] pxa: use 'pxa_last_gpio' instead of 'gpio_nr' in mfp-pxa2xx.c
The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we
already have that variable, remove the unnecessary 'gpio_nr' now.

Also, fix the incorrect GPIO number passed in pxa27x_init_irq().

Note: pxa_last_gpio should be initialized earlier, and this is true
since it's been assigned in machine_desc->init_irq().

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:36 +08:00
Robert Jarzmik
9968711468 [ARM] pxa: add muxed gpio wakeup sources on pxa2xx architectures
PXA SoC have several GPIOs muxed on only one wakeup source.
Add support for these wakeup sources which were missing
in mfp core support.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02 14:42:36 +08:00
David Howells
4280e3126f frv: fix mmap2 error handling
Fix the error handling in sys_mmap2().  Currently, if the pgoff check
fails, fput() might have to be called (which it isn't), so do the pgoff
check first, before fget() is called.

Signed-off-by: David Howells <dhowells@redhat.com>
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01 19:55:24 -08:00
Ben Dooks
b93c35ff39 spi: fix spi_s3c24xx_gpio num_chipselect
The spi master driver must have num_chipselect set to allow the bus to
initialise.  Pass this through the platform data.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01 19:55:24 -08:00
Russell King
d281bc9d8a [ARM] fix missing includes for iop33x and sa1100_ir
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 23:01:19 +00:00
Russell King
657e1de8e7 Merge branch 'for-rmk-realview' of git://linux-arm.org/linux-2.6 into devel 2008-12-01 17:53:45 +00:00
Kristoffer Ericson
93982535a2 [ARM] 5336/1: Formatting/Whitespace cleanups in mach-sa1100
This patch fixes bad formatting found in
mach-sa1100 files.

What it does is to replace/delete things like
excessive spaces (start || endline). The code
looks the same just alot less junk.

Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:22:45 +00:00
Hartley Sweeten
799a0600ac [ARM] 5324/2: ep93xx: support gpio interrupt debounce
Add debounce support for ep93xx gpio interrupts.

On the EP93xx, GPIO ports A, B, and F can be used to generate
interrupts. For each port, if interrupts are enabled, it is
possible to debouce the input signal. Debouncing is implemented
by passing the input signal through a 2-bit shift register clocked
by a 128Hz clock.

This patch adds a platform specific way to enable the debouce
feature for these input ports.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:22:09 +00:00
Hartley Sweeten
d52a26a956 [ARM] 5311/1: ep93xx: add core support for built in i2c bus
Allow the ep93xx platform init code to register the built-in i2c bus.

The EP93xx processor has two GPIO pins dedicated for an I2C bus. This
patch registers the platform supplied i2c_board_info and the necessary
platform_device information for the i2c-gpio driver to use these pins.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:22:08 +00:00
Hartley Sweeten
4c5744ed59 [ARM] 5309/1: ep93xx: add edb9307a platform
Add Cirrus Logic EDB9307A Dev Board to arch/arm/mach-ep93xx

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:22:08 +00:00
Stelian Pop
7be90a6ba9 [ARM] 5319/1: AT91: support AT91CAP9 revC CPUs
The AT91CAP9 revC CPU has a few differences over the previous,
revB CPU which was distributed in small quantities only (revA was
an internal Atmel product only).

This patch adds the detection routines to recognize the different
AT91CAP9 revisions (based on the PMC subsystem version number), and
uses them to:
	- activate a workaround for the external interrupts levels
	  (on revB CPUs)
	- set the UDPHS_BYPASS bit (on revB CPUs)
	- set AT91_GPBR register address to the correct offset
	  (0xfffffd50 on revB, 0xfffffd60 on revC)

For debugging usage, the CPU revision can be found in /proc/cpuinfo
on the 'Revision' line.

This patch is extracted from Andrew Victor's -at91 patch (2.6.27-at91.patch)
where it has been tested for the last 6 months.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:22:07 +00:00
Andrew Victor
ffc63b7d30 [ARM] 5290/1: [AT91] Add support for the Adeneo NeoCore 926 board
Add support for the Adeneo NeoCore 926 board.

Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:18:15 +00:00
Andrew Victor
8cdae51aa9 [ARM] 5289/1: [AT91] Convert boards to use sam9_smc_configure()
Convert the SAM9 and CAP9 board-specific files to make use of the
sam9_smc_configure() method to configure the memory-controller for
external peripherals.

The following boards have been modified:
 cam60 : NAND
 cap9adk : NAND, NOR
 qil-a9260 : NAND
 sam9-l9260 : NAND
 sam9260ek : NAND
 sam9261ek : DM9000 Ethernet, NAND
 sam9263 : NAND
 sam9g20ek : NAND
 sam9rlek : NAND
 usb-a9260 : NAND
 usb-a9263 .: NAND

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:18:13 +00:00
Andrew Victor
461d3b4dcf [ARM] 5288/1: [AT91] Remove SMC configuration from devices.c files
In at91_add_device_nand(), do not configure the Static Memory
controller with specific timing values.
The *_devices.c files are board independent, and the SMC timing values
are specific to the NAND devices that are installed on the board.
The board-specific files are now responsible for configuring the
Static Memory controller (if the don't want to leave it up to a
bootloader).

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:18:10 +00:00
Andrew Victor
6781002bec [ARM] 5287/2: [AT91] Configuration of Static Memory Controller
Add a structure 'sam9_smc_config' and function sam9_smc_configure() to
allow the board-specific files to specify the configuration of the
Static Memory Controller per chip-select.  This allows the board file
to specify timings for NAND flash, NOR flash or other external
peripherals.

This functionality can be used for all the SAM9 and CAP9 processors.
(the AT91RM9200 has a different memory-controller)
This patch is based on similar code in the AVR32 architecture.

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:18:08 +00:00
Linus Torvalds
ecf318cc3d Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: Fix build for 32-bit SMP configs
2008-12-01 07:58:23 -08:00
Linus Torvalds
33b07db9f3 Revert "of_platform_driver noise on sparce"
This reverts commit e669dae614, since it
is incomplete, and clashes with fuller patches and the sparc 32/64
unification effort.

Requested-by: David Miller <davem@davemloft.net>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01 07:55:14 -08:00
Catalin Marinas
6f13d27883 RealView: Select CPU_V6 for MACH_REALVIEW_PB11MP
This seems to be missing from the arm:devel branch, though the other
RealView configurations were modified accordingly.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-12-01 14:55:00 +00:00
Catalin Marinas
5582ad1838 RealView: Update the realview-smp_defconfig file to a newer kernel
The original file was based on 2.6.19-rc3. Apart from the new symbols,
the explicitly enabled eatures are AEABI, REALVIEW_HIGH_PHYS_OFFSET and
MACH_REALVIEW_PB11MP.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-12-01 14:55:00 +00:00
Catalin Marinas
2f152ad931 RealView: Update the realview_defconfig file to a newer kernel
The original file was based on 2.6.14-rc2. Apart from the new symbols,
the explicitly enabled features are AACI, MMC, AEABI,
MACH_REALVIEW_PB1176 and MACH_REALVIEW_PB11MP.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-12-01 14:54:59 +00:00
Catalin Marinas
0a5b2f6be7 RealView: Allow the in-kernel smc911x.c driver on RealView
This patch adds smc911x.c device configuration to the RealView
platforms. At some point it may be changed to the new smsc911x.c driver
(once complete testing was done).

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-12-01 14:54:59 +00:00
Catalin Marinas
0a3813306f RealView: Refactor the Ethernet device registration
This patch moves the Ethernet device registration from individual
realview_*.c files to core.c.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-12-01 14:54:58 +00:00
Catalin Marinas
1bbdf637ba RealView: Clean up the machine_is_*() calls in platsmp.c
Some of the calls weren't necessary and some others were duplicated.
This patch tidies up the platsmp.c file.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-12-01 14:54:58 +00:00