Certain users can not use right now the DMAengine API due to missing
features in the core. Prime example is Networking.
These users can use the glue layer interface to avoid misuse of DMAengine
API and when the core gains the needed features they can be converted to
use generic API.
The most prominent features the glue layer clients are depending on:
- most PSI-L native peripheral use extra rflow ranges on a receive channel
and depending on the peripheral's configuration packets from a single
free descriptor ring is going to be received to different receive ring
- it is also possible to have different free descriptor rings per rflow
and an rflow can also support 4 additional free descriptor ring based
on the size of the incoming packet
- out of order completion of descriptors on a channel
- when we have several queues to handle different priority packets the
descriptors will be completed 'out-of-order'
- the notion of prep_slave_sg is not matching with what the streaming type
of operation is demanding for networking
- Streaming type of operation
- Ability to fill the free descriptor ring with descriptors in
anticipation of incoming traffic and when a packet arrives UDMAP will
form a packet and gives it to the client driver
- the descriptors are not backed with exact size data buffers as we don't
know the size of the packet we will receive, but as a generic pool of
buffers to be used by the receive channel
- NAPI type of operation (polling instead of interrupt driven transfer)
- without this we can not sustain gigabit speeds and we need to support NAPI
- not to limit this to networking, but other high performance operations
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20191223110458.30766-12-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Split patch for review containing: defines, structs, io and low level
functions and interrupt callbacks.
DMA driver for
Texas Instruments K3 NAVSS Unified DMA – Peripheral Root Complex (UDMA-P)
The UDMA-P is intended to perform similar (but significantly upgraded) functions
as the packet-oriented DMA used on previous SoC devices. The UDMA-P module
supports the transmission and reception of various packet types. The UDMA-P is
architected to facilitate the segmentation and reassembly of SoC DMA data
structure compliant packets to/from smaller data blocks that are natively
compatible with the specific requirements of each connected peripheral. Multiple
Tx and Rx channels are provided within the DMA which allow multiple segmentation
or reassembly operations to be ongoing. The DMA controller maintains state
information for each of the channels which allows packet segmentation and
reassembly operations to be time division multiplexed between channels in order
to share the underlying DMA hardware. An external DMA scheduler is used to
control the ordering and rate at which this multiplexing occurs for Transmit
operations. The ordering and rate of Receive operations is indirectly controlled
by the order in which blocks are pushed into the DMA on the Rx PSI-L interface.
The UDMA-P also supports acting as both a UTC and UDMA-C for its internal
channels. Channels in the UDMA-P can be configured to be either Packet-Based or
Third-Party channels on a channel by channel basis.
The initial driver supports:
- MEM_TO_MEM (TR mode)
- DEV_TO_MEM (Packet / TR mode)
- MEM_TO_DEV (Packet / TR mode)
- Cyclic (Packet / TR mode)
- Metadata for descriptors
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20191223110458.30766-11-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In K3 architecture the DMA operates within threads. One end of the thread
is UDMAP, the other is on the peripheral side.
The UDMAP channel configuration depends on the needs of the remote
endpoint and it can be differ from peripheral to peripheral.
This patch adds database for am654 and j721e and small API to fetch the
PSI-L endpoint configuration from the database which should only used by
the DMA driver(s).
Another API is added for native peripherals to give possibility to pass new
configuration for the threads they are using, which is needed to be able to
handle changes caused by different firmware loaded for the peripheral for
example.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20191223110458.30766-9-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
