With binutils 2.24 the attempt to switch with microMIPS mode to MIPS III
mode through .set mips3 results in *lots* of warnings like
{standard input}: Assembler messages:
{standard input}:397: Warning: the 64-bit MIPS architecture does not support the `smartmips' extension
during a kernel build. Fixed by using .set arch=r4000 instead.
This breaks support for building the kernel with binutils 2.13 which
was supported for 32 bit kernels only anyway and 2.14 which was a bad
vintage for MIPS anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This function simply returns the number of VPEs present in the current
core, or 1 if the core does not implement the MT ASE. In SMP kernels
this will typically equal smp_num_siblings, however it will also be
usable in UP kernels and helps prepare for the possibility of a
heterogenous system where the VPE count is not the same across all
cores.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6665/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Both the CONFIG_MIPS_CPS & CONFIG_MIPS_CMP SMP implementations call
mips_mt_set_cpuoptions when preparing to start secondary CPUs. However
both may be used without MT. Provide an empty inline function to prevent
a link error in this case.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6647/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch ensures that the kernel sets a sane base address for the
PIIX4 PM I/O register region during boot. Without this the kernel may
not successfully claim the region as a resource if the bootloader didn't
configure the region. With this patch the kernel will always succeed
with:
pci 0000:00:0a.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI
The lack of the resource claiming is easily reproducible without this
patch using current versions of QEMU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Tested-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6641/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tips of Loongson's CPU hotplug:
1, To fully shutdown a core in Loongson 3, the target core should go to
CKSEG1 and flush all L1 cache entries at first. Then, another core
(usually Core 0) can safely disable the clock of the target core. So
play_dead() call loongson3_play_dead() via CKSEG1 (both uncached and
unmmaped).
2, The default clocksource of Loongson is MIPS. Since clock source is a
global device, timekeeping need the CP0' Count registers of each core
be synchronous. Thus, when a core is up, we use a SMP_ASK_C0COUNT IPI
to ask Core-0's Count.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6639
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IPI registers of Loongson-3 include IPI_SET, IPI_CLEAR, IPI_STATUS,
IPI_EN and IPI_MAILBOX_BUF. Each bit of IPI_STATUS indicate a type of
IPI and IPI_EN indicate whether the IPI is enabled. The sender write 1
to IPI_SET bits generate IPIs in IPI_STATUS, and receiver write 1 to
bits of IPI_CLEAR to clear IPIs. IPI_MAILBOX_BUF are used to deliver
more information about IPIs.
Why we change code in arch/mips/loongson/common/setup.c?
If without this change, when SMP configured, system cannot boot since
it hang at printk() in cgroup_init_early(). The root cause is:
console_trylock()
\-->down_trylock(&console_sem)
\-->raw_spin_unlock_irqrestore(&sem->lock, flags)
\-->_raw_spin_unlock_irqrestore()(SMP/UP have different versions)
\-->__raw_spin_unlock_irqrestore() (following is the SMP case)
\-->do_raw_spin_unlock()
\-->arch_spin_unlock()
\-->nudge_writes()
\-->mb()
\-->wbflush()
\-->__wbflush()
In previous code __wbflush() is initialized in plat_mem_setup(), but
cgroup_init_early() is called before plat_mem_setup(). Therefore, In
this patch we make changes to avoid boot failure.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6638
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson doesn't support DMA address above 4GB traditionally. If memory
is more than 4GB, CONFIG_SWIOTLB and ZONE_DMA32 should be selected. In
this way, DMA pages are allocated below 4GB preferably. However, if low
memory is not enough, high pages are allocated and swiotlb is used for
bouncing.
Moreover, we provide a platform-specific dma_map_ops::set_dma_mask() to
set a device's dma_mask and coherent_dma_mask. We use these masks to
distinguishes an allocated page can be used for DMA directly, or need
swiotlb to bounce.
Recently, we found that 32-bit DMA isn't a hardware bug, but a hardware
configuration issue. So, latest firmware has enable the DMA support as
high as 40-bit. To support all-memory DMA for all devices (besides the
Loongson platform limit, there are still some devices have their own
DMA32 limit), and also to be compatible with old firmware, we keep use
swiotlb.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6636
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IRQ routing path of Loongson-3:
Devices(most) --> I8259 --> HT Controller --> IRQ Routing Table --> CPU
^
|
Device(legacy devices such as UART) --> Bonito ---|
IRQ Routing Table route 32 INTs to CPU's INT0~INT3(IP2~IP5 of CP0), 32
INTs include 16 HT INTs(mostly), 4 PCI INTs, 1 LPC INT, etc. IP6 is used
for IPI and IP7 is used for internal MIPS timer. LOONGSON_INT_ROUTER_*
are IRQ Routing Table registers.
I8259 IRQs are 1:1 mapped to HT1 INTs. LOONGSON_HT1_* are configuration
registers of HT1 controller.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6634
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson family machines use Hyper-Transport bus for inter-core
connection and device connection. The PCI bus is a subordinate
linked at HT1.
With LEFI firmware interface, We don't need fixup for PCI irq routing
(except providing a VBIOS of the integrated GPU).
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6633
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The new UEFI-like firmware interface (LEFI, i.e. Loongson Unified
Firmware Interface) has 3 advantages:
1, Firmware export a physical memory map which is similar to X86's
E820 map, so prom_init_memory() will be more elegant that #ifdef
clauses can be removed.
2, Firmware export a pci irq routing table, we no longer need pci
irq routing fixup in kernel's code.
3, Firmware has a built-in vga bios, and its address is exported,
the linux kernel no longer need an embedded blob.
With the LEFI interface, Loongson-3A/2G and all their successors can use
a unified kernel. All Loongson-based machines support this new interface
except 2E/2F series.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6632
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add four Loongson-3 based machine types:
MACH_LEMOTE_A1004/MACH_LEMOTE_A1201 are laptops;
MACH_LEMOTE_A1101 is mini-itx;
MACH_LEMOTE_A1205 is all-in-one machine.
The most significant differrent between A1004/A1201 and A1101/A1205 is
the laptops have EC but others don't.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6631
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Basic Loongson-3 CPU support include CPU probing and TLB/cache
initializing.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6630
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3 is a multi-core MIPS family CPU, it support MIPS64R2 fully.
Loongson-3 has the same IMP field (0x6300) as Loongson-2.
Loongson-3 has a hardware-maintained cache, system software doesn't
need to maintain coherency.
Loongson-3A is the first revision of Loongson-3, and it is the quad-
core version of Loongson-2G. Loongson-3A has a simplified version named
Loongson-2Gq, the main difference between Loongson-3A/2Gq is 3A has two
HyperTransport controller but 2Gq has only one. HT0 is used for cross-
chip interconnection and HT1 is used to link PCI bus. Therefore, 2Gq
cannot support NUMA but 3A can. For software, Loongson-2Gq is simply
identified as Loongson-3A.
Exsisting Loongson family CPUs:
Loongson-1: Loongson-1A, Loongson-1B, they are 32-bit MIPS CPUs.
Loongson-2: Loongson-2E, Loongson-2F, Loongson-2G, they are 64-bit
single-core MIPS CPUs.
Loongson-3: Loongson-3A(including so-called Loongson-2Gq), they are
64-bit multi-core MIPS CPUs.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6629/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And there are more CPUs or configurations that want to provide special
per-CPU information in /proc/cpuinfo. So I think there needs to be a
hook mechanism, such as a notifier.
This is a first cut only; I need to think about what sort of looking
the notifier needs to have. But I'd appreciate testing on MT hardware!
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6066/
Loongson-1 is a 32-bit MIPS CPU and Loongson-2/3 are 64-bit MIPS CPUs,
and both Loongson-2/3 has the same PRID IMP filed (0x6300). As a
result, renaming PRID_IMP_LOONGSON1 and PRID_IMP_LOONGSON2 to
PRID_IMP_LOONGSON_32 and PRID_IMP_LOONGSON_64 will make more sense.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6552/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The UART register names are identical to the ones in uapi/linux/serial_reg.h,
which causes build failures in various drivers when they indirectly pull in
the au1000.h header, for example via gpio.h:
In file included from arch/mips/include/asm/mach-au1x00/gpio.h:13:0,
from arch/mips/include/asm/gpio.h:4,
from include/linux/gpio.h:48,
from include/linux/ssb/ssb.h:9,
from drivers/ssb/driver_mipscore.c:11:
arch/mips/include/asm/mach-au1x00/au1000.h:1171:0: note: this is the location of the previous definition
#define UART_LSR 0x1C /* Line Status Register */
Get rid of the altogether, nothing in the core Alchemy code depends
on them any more.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6664/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a few Belkin F7Dxxxx entries, with F7D4401 sourced from online
documentation and the "F7D7302" being observed. F7D3301, F7D3302, and
F7D4302 are reasonable guesses which are unlikely to cause
mis-detection.
Signed-off-by: Cody P Schafer <devel@codyps.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Cc: Cody P Schafer <devel@codyps.com>
Patchwork: https://patchwork.linux-mips.org/patch/6594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds board detection for the Siemens SE505v2 and the led gpio
configuration. This board does not have any buttons.
This is based on OpenWrt broadcom-diag and Manuel Munz's nvram dump.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6593/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Linksys WRT54G/GS/GL family uses the same boardtype numbers, and
the same gpio configuration. The boardtype numbers are changing with
the hardware versions, but these hardware numbers are different or each
model.
Detect them all as one device, this also worked in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6591/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The M5150 core is a 32-bit MIPS RISC which implements the
MIPS Architecture Release-5 in a 5-stage pipeline.
In addition, it includes the MIPS Architecture Virtualization Module
that enables virtualization of operating systems,
which provides a scalable, trusted, and secure execution environment.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6596/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge the db1200.h and db1300.h headers into their only users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6660/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Setting DMA_MAYBE_COHERENT gives a platform the opportunity to select
use of cache ops at boot.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6575/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow secondary cores to program their segment control registers
during smp bootstrap code. This enables EVA on Malta SMP
configurations
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The 'ememsize' variable is used to denote the real RAM which is
present on the Malta board. This is different compared to 'memsize'
which is capped to 256MB. The 'ememsize' is used to get the actual
physical memory when setting up the Malta memory layout. This only
makes sense in case the core operates in the EVA mode, and it's
ignored otherwise.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Add a spaces.h file for Malta to override certain memory macros
when operating in EVA mode.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The Malta board aliases 0x80000000 - 0xffffffff to 0x00000000
- 0x7fffffff ignoring the 256 MB IO hole in 0x10000000.
The physical memory is shifted to 0x80000000 so up to 2GB
can be used. Kuseg is expanded to 3GB (due to board limitations
only 2GB can be accessed) and lowmem (kernel space) is expanded to 2GB.
The Segment Control registers are programmed as follows:
Virtual memory Physical memory Mapping
0x00000000 - 0x7fffffff 0x80000000 - 0xfffffffff MUSUK (kuseg)
0x80000000 - 0x9fffffff 0x00000000 - 0x1ffffffff MUSUK (kseg0)
0xa0000000 - 0xbf000000 0x00000000 - 0x1ffffffff MUSUK (kseg1)
0xc0000000 - 0xdfffffff - MK (kseg2)
0xe0000000 - 0xffffffff - MK (kseg3)
The location of exception vectors remain the same since 0xbfc00000
(traditional exception base) still maps to 0x1fc00000 physical.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
A core in EVA mode can have any possible segment mapping, so the
default free_initmem_default() function may not always work as expected.
Therefore, add a callback that platforms can use to free up the init section.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The MIPS *Aptiv family uses bit 28 in Config5 CP0 register to
indicate whether the core supports EVA or not.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
This will allow platforms to use an alternative way to get
the physical address of a symbol.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Add EVA cache flushing functions similar to non-EVA configurations.
Because the cache may or may not contain user virtual addresses, we
need to use the 'cache' or 'cachee' instruction based on whether we
flush the cache on behalf of kernel or user respectively.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Build code to invalidate an address range in the instruction cache
using the Hit Invalidate cache operation.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
A MIPS specific csum_and_copy_from_user function is necessary because
the generic one from include/net/checksum.h will not work for EVA.
This is because the generic one will link to symbols from lib/checksum.c
which are not EVA aware.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
In EVA mode, different instructions need to be used to read/write
from kernel and userland. In non-EVA mode, there is no functional
difference. The current address limit is checked to decide the
type of operation that will be performed.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The 'copy_user' symbol can be used to copy from or to
userland so we will use two different symbols for these
operations. This makes no difference in the existing code,
but when the core is operating in EVA mode, different instructions
need to be used to read and write to userland address space.
The old function has also been renamed to 'copy_kernel' to denote
that it is suitable for copy data to and from kernel space.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The str*_user functions are used to securely access NULL terminated
strings from userland. Therefore, it's necessary to use the appropriate
EVA function. However, if the string is in kernel space, then the normal
instructions are being used to access it. The __str*_kernel_asm and
__str*_user_asm symbols are the same for non-EVA mode so there is no
functional change for the non-EVA kernels.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use the EVA specific functions from memcpy.S to perform
userspace operations. When get_fs() == get_ds() the usual load/store
instructions are used because the destination address is located in
the kernel address space region. Otherwise, the EVA specifc load/store
instructions are used which will go through th TLB to perform the virtual
to physical translation for the userspace address.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The {get,put}_user_asm functions can be used to load data from
kernel or the user address space so rename them to avoid
confusion.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use the EVA instruction wrappers from asm.h to perform
read/write operations from userland.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
ulb, ulh, ulw are macros which emulate unaligned access for MIPS.
However, no such macros exist for EVA mode, so the only way to do
EVA unaligned accesses is in the ADE exception handler. As a result
of which, disable these macros for EVA.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Similar to __get_user_* functions, move common code to
__put_user_*_common so it can be shared among similar users.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
In preparation for EVA support, an instruction argument is needed
for the __get_user_asm{,_ll32} functions to allow instruction overrides in
EVA mode. Even though EVA only works for MIPS 32-bit, both codepaths are
changed (32-bit and 64-bit) for consistency reasons.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use LLE/SCE instructions for performing an address translation for
userspace when EVA is enabled.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
EVA uses specific instructions for accessing user memory.
Instead of polluting the kernel with numerous #ifdef CONFIG_EVA
we add wrappers for all the instructions that need special
handling when EVA is enabled.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
EVA can use the PREFE instruction to perform the virtual address
translation using the user mapping of the address rather than the
kernel mapping.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Add a CPU_P5600 case to various switch statements, doing the same thing
as for CPU_PROAPTIV.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6408/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a Processor ID and CPU type for the MIPS P5600 core.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6407/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch extends sigcontext in order to hold the most significant 64
bits of each vector register in addition to the MSA control & status
register. The least significant 64 bits are already saved as the scalar
FP context. This makes things a little awkward since the least & most
significant 64 bits of each vector register are not contiguous in
memory. Thus the copy_u & insert instructions are used to transfer the
values of the most significant 64 bits via GP registers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6533/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for context switching the MSA vector registers.
These 128 bit vector registers are aliased with the FP registers - an
FP register accesses the least significant bits of the vector register
with which it is aliased (ie. the register with the same index). Due to
both this & the requirement that the scalar FPU must be 64-bit (FR=1) if
enabled at the same time as MSA the kernel will enable MSA & scalar FP
at the same time for tasks which use MSA. If we restore the MSA vector
context then we might as well enable the scalar FPU since the reason it
was left disabled was to allow for lazy FP context restoring - but we
just restored the FP context as it's a subset of the vector context. If
we restore the FP context and have previously used MSA then we have to
restore the whole vector context anyway (see comment in
enable_restore_fp_context for details) so similarly we might as well
enable MSA.
Thus if a task does not use MSA then it will continue to behave as
without this patch - the scalar FP context will be saved & restored as
usual. But if a task executes an MSA instruction then it will save &
restore the vector context forever more.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6431/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for probing the MSAP bit within the Config3
register in order to detect the presence of the MSA ASE. Presence of the
ASE will be indicated in /proc/cpuinfo. The value of the MSA
implementation register will be displayed at boot to aid debugging and
verification of a correct setup, as is done for the FPU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6430/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces definitions for the MSA control registers and
functions which allow access to both the control & vector registers. If
the toolchain being used to build the kernel includes support for MSA
then this patch will make use of that support & use MSA instructions
directly. However toolchain support for MSA is very new & far from a
point where it can be reasonably expected that everyone building the
kernel uses a toolchain with support. Thus fallbacks using .word
assembler directives are also provided for now as a temporary measure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6429/
Patchwork: https://patchwork.linux-mips.org/patch/6607/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When saving or restoring scalar FP context we want to access the least
significant 64 bits of each FP register. When the FP registers are 64
bits wide that is trivially the start of the registers value in memory.
However when the FP registers are wider this equivalence will no longer
be true for big endian systems. Define a new set of offset macros for
the least significant 64 bits of each saved FP register within thread
context, and make use of them when saving and restoring scalar FP
context.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6428/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The hard-coded offsets mentioned in this comment seem to not exist
anymore, so remove mention of them from the comment.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6421/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces the fpureg_t typedef with a "union fpureg" enabling
easier access to 32 & 64 bit values. This allows the access macros used
in cp1emu.c to be simplified somewhat. It will also make it easier to
expand the width of the FP registers as will be done in a future
patch in order to support the 128 bit registers introduced with MSA.
No behavioural change is intended by this patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6532/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When userland uses syscall() to perform an indirect system call
the actually system call that needs to be checked by the filter
is on the first argument. The kernel code needs to handle this case
by looking at the original syscall number in v0 and if it's
NR_syscall, then it needs to examine the first argument to
identify the real system call that will be executed.
Similarly, we need to 'virtually' shift the syscall() arguments
so the syscall_get_arguments() function can fetch the correct
arguments for the indirect system call.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6404/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS now has the infrastructure for dynamic seccomp-bpf
filtering
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6400/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add _TIF_SECCOMP flag to _TIF_WORK_SYSCALL_ENTRY to indicate
that the system call needs to be checked against a seccomp filter.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6405/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This effectively renames __syscall_get_arch to syscall_get_arch
and implements a compatible interface for the seccomp API.
The seccomp code (kernel/seccomp.c) expects a syscall_get_arch
function to be defined for every architecture, so we drop
the leading underscores from the existing function.
This also makes use of the 'task' argument to determine the type
the process instead of assuming the process has the same
characteristics as the kernel it's running on.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6398/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The syscall_rollback function is used by seccomp-bpf but it was never
added for MIPS. It doesn't need to do anything as none of the registers
are clobbered if the system call has been denied by the seccomp filter.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6403/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This header was used only by Malta but is used no longer. Remove it. It
was also included unnecessarily in irq-gic.c, so that include is also
removed.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6366/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When CPC support is compiled into the kernel (ie. CONFIG_MIPS_CPC=y),
probe the CPC on boot for Malta in order to allow any users of the CPC
to detect its presence & function correctly.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the Malta-specific CM probe code and instead make use of the
newly added generic CM code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The vpe_id field of struct cpuinfo_mips is only present when one of
CONFIG_MIPS_MT_{SMP,SMTC} is enabled. That means that any code accessing
which may compile without MT is currently forced to use an #ifdef.
Instead this patch provides an accessor macro, #ifdef'd appropriately
to prevent further #ifdef's elsewhere.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6646/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For non-mipsr2 processors, the local_irq_disable contains an mfc0-mtc0
pair with instructions inbetween. With preemption enabled, this sequence
may get preempted and effect a stale value of CP0_STATUS when executing
the mtc0 instruction. This commit avoids this scenario by incrementing
the preempt count before the mfc0 and decrementing it after the mtc9.
[ralf@linux-mips.org: This patch is sorting out the part that were missed
by e97c5b6098 [MIPS: Make irqflags.h functions preempt-safe for non-mipsr2
cpus.] I also re-enabled the inclusion of <asm/asm-offsets.h> at the top
of <asm/asmmacro.h>].
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Due to name collision in ftrace safe_load and safe_store macros,
these macros cannot take expressions as operands.
For example, compiler will complain for a macro call like the following:
safe_store_code(new_code2, ip + 4, faulted);
arch/mips/include/asm/ftrace.h:61:6: note: in definition of macro 'safe_store'
: [dst] "r" (dst), [src] "r" (src)\
^
arch/mips/kernel/ftrace.c:118:2: note: in expansion of macro 'safe_store_code'
safe_store_code(new_code2, ip + 4, faulted);
^
arch/mips/kernel/ftrace.c:118:32: error: undefined named operand 'ip + 4'
safe_store_code(new_code2, ip + 4, faulted);
^
arch/mips/include/asm/ftrace.h:61:6: note: in definition of macro 'safe_store'
: [dst] "r" (dst), [src] "r" (src)\
^
arch/mips/kernel/ftrace.c:118:2: note: in expansion of macro 'safe_store_code'
safe_store_code(new_code2, ip + 4, faulted);
^
This build error is triggered by a4671094 [MIPS: ftrace: Fix icache flush
range error]. Tweak variable naming in those macros to allow flexible
operands.
Signed-off-by: Viller Hsiao <villerhsiao@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: rostedt@goodmis.org
Cc: fweisbec@gmail.com
Cc: mingo@redhat.com
Cc: Qais.Yousef@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/6622/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ability to read hardware registers from userland with the RDHWR
instruction should depend upon the corresponding bit of the HWREna
register being set, otherwise a reserved instruction exception should be
generated.
However KVM's current emulation ignores the guest's HWREna and always
emulates RDHWR instructions even if the guest OS has disallowed them.
Therefore rework the RDHWR emulation code to check for privilege or the
corresponding bit in the guest HWREna bit. Also remove the #if 0 case
for the UserLocal register. I presume it was there for debug purposes
but it seems unnecessary now that the guest can control whether it
causes a guest exception.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The whitespace in asm/kvm_host.h is quite inconsistent in places. Clean
up the whole file to use tabs more consistently.
When you use the --ignore-space-change argument to git diff this patch
only changes line wrapping in TLB_IS_GLOBAL and TLB_IS_VALID macros.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The syscall_get_arguments function expects the arguments to be copied
to the '*args' argument but instead a local variable was used to hold
the system call argument. As a result of which, this variable was
never passed to the filter and any filter testing the system call
arguments would fail. This is fixed by passing the '*args' variable
as the destination memory for the system call arguments.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6402/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 597ce1723e ("MIPS: Support for 64-bit FP with O32 binaries")
introduced references to two undefined Kconfig macros. CONFIG_MIPS32_R2
should clearly be replaced with CONFIG_CPU_MIPS32_R2. And CONFIG_MIPS64
should be replaced with CONFIG_64BIT.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6522/
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When running applications which contain the instruction "prefx" on FPU-less
CPUs, a message "Illegal instruction" will be seen. This instruction is
supposed to be ignored by the FPU emulator. However, its current detection
and function field encoding are incorrect. This patch fix the issue.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/6608/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove mc_capable() and smt_capable(). Neither is used.
Both were added by 5c45bf279d ("sched: mc/smt power savings sched
policy"). Uses of both were removed by 8e7fbcbc22 ("sched: Remove stale
power aware scheduling remnants and dysfunctional knobs").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/20140304210737.16893.54289.stgit@bhelgaas-glaptop.roam.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch introduces code to probe for a MIPS Cluster Power Controller
& accessor functions to allow for easy register access. This support
code will be used by a subsequent patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6361/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel currently only probes for a MIPS Coherence Manager in the
Malta interrupt code in order to detect & enable the GIC. However CM is
not Malta-specific, so this should really be more generic. This patch
introduces some non-Malta-specific code which probes for a CM and
performs some basic initialisation.
A new header, with temporarily duplicated register definitions, is
introduced in order to:
1) Allow the new definitions to be correct with regards to the
CM documentation, as many of those in gcmpregs.h aren't.
2) Allow switching away from the REG() macro used via a few layers of
nested macros in order to access registers in gcmpregs.h. This
patch instead introduced accessor functions akin to the
{read,write}_c0_* functions used for cop0 registers.
3) Allow users of the CM to be migrated one by one.
4) Switch from the name 'GCMP' to 'CM' since the Coherence Manager is
what this code is actually dealing with.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6360/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GIC IPI functions aren't necessarily specific to the "CMP
framework" SMP implementation, and will be used elsewhere in a
subsequent commit. This patch adds cleaned up GIC IPI functions to a
separate file which is compiled when a new CONFIG_MIPS_GIC_IPI Kconfig
symbol is selected, and selects that symbol for CONFIG_MIPS_CMP.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6359/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a simple macro to wrap the ext instruction which was
introduced with MIPSR2, and fall back to a shift & and pair for
pre-MIPSR2 CPUs. This will be used in a subsequent patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6358/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The gic.h header uses bitmaps and NR_CPUS, and should therefore include
linux/bitmap.h and linux/threads.h. This is in preparation for use of
this header in a subsequent commit from a C file which doesn't already
include those headers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CMGCRBase register is defined by the PRA specification as an optional
register which indicates the physical base of the MIPS Coherence Manager
Global Control Register block. This patch simply adds a definition for
the base address field within the register, along with an accessor
function for reading the register.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6356/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These fields will be used from assembly code in a subsequent commit, and
defining the size & offset of each field makes that use easier.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 1074K is a multiprocessing coherent processing system (CPS) based
on modified 74K cores. This patch makes the 1074K an actual unique
CPU type, instead of a 74K derivative, which it is not.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6389/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The *Aptiv cores can use the CONF7/IAR bit to detect if the core
has hardware support to remove instruction cache aliasing.
This also defines the CONF7/AR bit in order to avoid using
the '16' magic number.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6499/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/kernel/ptrace.o
In file included from arch/mips/kernel/ptrace.c:42:0:
arch/mips/kernel/ptrace.c: In function ‘mips_get_syscall_arg’:
/home/ralf/src/linux/linux-mips/arch/mips/include/asm/syscall.h:60:1: error: control reaches end of non-void function [-Werror=return-type]
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/kernel/ptrace.o] Error 1
make[1]: *** [arch/mips/kernel] Error 2
make: *** [arch/mips] Error 2
Fixed by marking the end of mips_get_syscall_arg() as unreachable.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For architecture dependent compat syscalls in common code an architecture
must define something like __ARCH_WANT_<WHATEVER> if it wants to use the
code.
This however is not true for compat_sys_getdents64 for which architectures
must define __ARCH_OMIT_COMPAT_SYS_GETDENTS64 if they do not want the code.
This leads to the situation where all architectures, except mips, get the
compat code but only x86_64, arm64 and the generic syscall architectures
actually use it.
So invert the logic, so that architectures actively must do something to
get the compat code.
This way a couple of architectures get rid of otherwise dead code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This patch allows each architecture to add its specific assembly optimized
arch_mcs_spin_lock_contended and arch_mcs_spinlock_uncontended for
MCS lock and unlock functions.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: AswinChandramouleeswaran <aswin@hp.com>
Cc: George Spelvin <linux@horizon.com>
Cc: Rik vanRiel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: MichelLespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Figo.zhang" <figo1802@gmail.com>
Cc: "Paul E.McKenney" <paulmck@linux.vnet.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew R Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1390347382.3138.67.camel@schen9-DESK
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We perform a clean up of the Kbuid files in each architecture.
We order the files in each Kbuild in alphabetical order
by running the below script.
for i in arch/*/include/asm/Kbuild
do
cat $i | gawk '/^generic-y/ {
i = 3;
do {
for (; i <= NF; i++) {
if ($i == "\\") {
getline;
i = 1;
continue;
}
if ($i != "")
hdr[$i] = $i;
}
break;
} while (1);
next;
}
// {
print $0;
}
END {
n = asort(hdr);
for (i = 1; i <= n; i++)
print "generic-y += " hdr[i];
}' > ${i}.sorted;
mv ${i}.sorted $i;
done
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Matthew R Wilcox <matthew.r.wilcox@intel.com>
Cc: AswinChandramouleeswaran <aswin@hp.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: "Paul E.McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "Figo.zhang" <figo1802@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: George Spelvin <linux@horizon.com>
Cc: MichelLespinasse <walken@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
[ Fixed build bug. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
__enable_fpu produces a build failure when CONFIG_BUG is not set:
In file included from arch/mips/kernel/cpu-probe.c:24:0:
arch/mips/include/asm/fpu.h: In function '__enable_fpu':
arch/mips/include/asm/fpu.h:77:1: error: control reaches end of non-void function [-Werror=return-type]
This is regression introduced in 3.14-rc1. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Paul Burton <paul.burton@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6504/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Wire up for MIPS the new sched_setattr and sched_getattr system calls
added in commit d50dde5a10 (sched: Add new scheduler syscalls to
support an extended scheduling parameters ABI) merged in v3.14-rc1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6502/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"The most notable new addition inside this pull request is the support
for MIPS's latest and greatest core called "inter/proAptiv". The
patch series describes this core as follows.
"The interAptiv is a power-efficient multi-core microprocessor
for use in system-on-chip (SoC) applications. The interAptiv combines
a multi-threading pipeline with a coherence manager to deliver improved
computational throughput and power efficiency. The interAptiv can
contain one to four MIPS32R3 interAptiv cores, system level
coherence manager with L2 cache, optional coherent I/O port,
and optional floating point unit."
The platform specific patches touch all 3 Broadcom families. It adds
support for the new Broadcom/Netlogix XLP9xx Soc, building a common
BCM63XX SMP kernel for all BCM63XX SoCs regardless of core type/count
and full gpio button/led descriptions for BCM47xx.
The rest of the series are cleanups and bug fixes that are MIPS
generic and consist largely of changes that Imgtec/MIPS had published
in their linux-mti-3.10.git stable tree. Random other cleanups and
patches preparing code to be merged in 3.15"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
mips: select ARCH_MIGHT_HAVE_PC_SERIO
mips: delete non-required instances of include <linux/init.h>
MIPS: KVM: remove shadow_tlb code
MIPS: KVM: use common EHINV aware UNIQUE_ENTRYHI
mips/ide: flush dcache also if icache does not snoop dcache
MIPS: BCM47XX: fix position of cpu_wait disabling
MIPS: BCM63XX: select correct MIPS_L1_CACHE_SHIFT value
MIPS: update MIPS_L1_CACHE_SHIFT based on MIPS_L1_CACHE_SHIFT_<N>
MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>
MIPS: ZBOOT: gather string functions into string.c
arch/mips/pci: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
bcma: gpio: don't cast u32 to unsigned long
ssb: gpio: add own IRQ domain
MIPS: BCM47XX: fix sparse warnings in board.c
MIPS: BCM47XX: add board detection for Linksys WRT54GS V1
MIPS: BCM47XX: fix detection for some boards
MIPS: BCM47XX: Enable buttons support on SSB
MIPS: BCM47XX: Convert WNDR4500 to new syntax
MIPS: BCM47XX: Use "timer" trigger for status LEDs
...
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Pull user namespaces work from Eric Biederman:
"The work to convert the kernel to use kuid_t and kgid_t has been
finished since 3.12 so it is time to remove the scaffolding that
allowed the work to progress incrementally.
The first patch on this branch just removes the scaffolding, ensuring
we will always get compile errors if people accidentally try the
userspace and the kernel uid and gid types. The second patch an
overlooked and unused chunk of mips code that that fails to build
after the first patch.
The code hasn't been in linux-next for long (as I was out of it and
could not sheppared the cold properly) but the patch has been around
for a long time just waiting for the day when I had finished the
uid/gid conversions. Putting the code in linux-next did find the
compile failure on mips so I took the time to get that fix reviewed
and included. Beyond that I am not too worried about errors because
all these two patches do is delete a modest amount of code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
MIPS: VPE: Remove vpe_getuid and vpe_getgid
userns: userns: Remove UIDGID_STRICT_TYPE_CHECKS
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6320/
The kvm_mips_init_shadow_tlb() function is called from
kvm_arch_vcpu_init() and initialises entries 0 to
current_cpu_data.tlbsize-1 of the virtual cpu's shadow_tlb[64] array.
However newer cores with FTLBs can have a tlbsize > 64, for example the
ProAptiv I'm testing on has a total tlbsize of 576. This causes
kvm_mips_init_shadow_tlb() to overflow the shadow_tlb[64] array and
overwrite the comparecount_timer among other things, causing a lock up
when starting a KVM guest.
Aside from kvm_mips_init_shadow_tlb() which only initialises it, the
shadow_tlb[64] array is only actually used by the following functions:
- kvm_shadow_tlb_put() & kvm_shadow_tlb_load()
These are never called. The only call sites are #if 0'd out.
- kvm_mips_dump_shadow_tlbs()
This is never called.
It was originally added for trap & emulate, but turned out to be
unnecessary so it was disabled.
So instead of fixing the shadow_tlb initialisation code, lets just
remove the shadow_tlb[64] array and the above functions entirely. The
only functional change here is the removal of broken shadow_tlb
initialisation. The rest just deletes dead code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Gleb Natapov <gleb@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6384/
If this is not done then the new just read data which remains in dcache
will not make it into icache on time. Thus the CPU loads invalid data
and executes crap. The result is that the user is not able to execute
anything from its IDE based media while reading plain data is still
working well.
This problem has been reported as Debian #404951http://bugs.debian.org/404951http://comments.gmane.org/gmane.linux.ide/45092
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/2820/
The early serial code is not needed because we already have early
printk support provided by common/earlycons.c
This change also fixes the following build error that occurs when
CONFIG_SERIAL_8250 is not configured for Netlogic XLR boards:
arch/mips/built-in.o: In function `nlm_early_serial_setup':
setup.c:(.init.text+0x274): undefined reference to `early_serial_setup'
make: *** [vmlinux] Error 1
Reported-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6083/
XLP9XX has a USB 3.0 controller on-chip with 2 xHCI ports. The USB
block is similar to the one on XLP2XX, so update usb-init-xlp2.c
to handle XLP9XX as well.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6285/
Add PCI support for Netlogic XLP9XX. The PCI registers and
SoC bus numbers have changed in XLP9XX.
Also skip a few (bus,dev,fn) combinations which have issues when
read.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6284/
XLP9XX has 20 cores per node, opposed to 8 on earlier XLP8XX.
Update code that calculates node id from cpu id to handle this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6283/
Update bridge code. Add code to the XLP9XX registers for DRAM
size, limit and node when running on XLPXX
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6282/
Update IO offset of the early console UART.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6281/
Add the SYS block registers for XLP9XX, most of them have changed.
The wakeup sequence has been updated to set the coherent mode from
the main thread rather than the woken up thread.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6280/
Functions for the XLP9XX interrupt table entry format and other PIC
register changes.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6279/
Most IO block offsets have changed in XLP9XX. Update iomap.h to add the
new addresses of different SoC blocks like PIC, SYS, UART etc. that are
needed by the base code.
On XLP9xx, the SoC blocks of other nodes are seen on a PCI bus
corresponding to the node. Update iomap code to reflect this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6277/
Adds processor ID of XLP 9XX to asm/cpu.h. Update netlogic/xlp-hal/xlp.h
to add cpu_is_xlp9xx() and to update cpu_is_xlpii() to support XLP 9XX.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6274/
Add macro nlm_node_present() that can be used to check if a node is present
in a multi-chip configuration. This can be used even when NUMA is not enabled.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6272/
Add mach-netlogic/topology.h which contains XLP cpu number to core and
node mapping.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6271/
Add MSI chip and MSIX chip definitions.
For MSI, we map the link interrupt to a MSI link IRQ which will
do a second level of dispatch based on the MSI status register.
The MSI chip definitions use the MSI enable register to enable
and disable the MSI irqs.
For MSI-X, we split the 32 available MSI-X vectors across the
four PCIe links (8 each). These PIC interrupts generate an IRQ
per link which uses a second level dispatch as well.
The MSI-X chip definition uses the standard functions to enable
and disable interrupts.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6270/
The platform data already available in tree for JZ4740 USB Device
Controller was previously used by an out-of-tree USB gadget driver
which was not relying on the musb driver and was written by Ingenic
and the Qi-Hardware community.
Update platform data for JZ4740 USB device controller to be used with
musb driver.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6265/
This patch cleans up the declaration of the resume function by replacing
void pointers with their correct types. The irrelevant & incorrect
comment preceeding the resume function is replaced by one documenting
its function.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6146/
Merge second patch-bomb from Andrew Morton:
- various misc bits
- the rest of MM
- add generic fixmap.h, use it
- backlight updates
- dynamic_debug updates
- printk() updates
- checkpatch updates
- binfmt_elf
- ramfs
- init/
- autofs4
- drivers/rtc
- nilfs
- hfsplus
- Documentation/
- coredump
- procfs
- fork
- exec
- kexec
- kdump
- partitions
- rapidio
- rbtree
- userns
- memstick
- w1
- decompressors
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (197 commits)
lib/decompress_unlz4.c: always set an error return code on failures
romfs: fix returm err while getting inode in fill_super
drivers/w1/masters/w1-gpio.c: add strong pullup emulation
drivers/memstick/host/rtsx_pci_ms.c: fix ms card data transfer bug
userns: relax the posix_acl_valid() checks
arch/sh/kernel/dwarf.c: use rbtree postorder iteration helper instead of solution using repeated rb_erase()
fs-ext3-use-rbtree-postorder-iteration-helper-instead-of-opencoding-fix
fs/ext3: use rbtree postorder iteration helper instead of opencoding
fs/jffs2: use rbtree postorder iteration helper instead of opencoding
fs/ext4: use rbtree postorder iteration helper instead of opencoding
fs/ubifs: use rbtree postorder iteration helper instead of opencoding
net/netfilter/ipset/ip_set_hash_netiface.c: use rbtree postorder iteration instead of opencoding
rbtree/test: test rbtree_postorder_for_each_entry_safe()
rbtree/test: move rb_node to the middle of the test struct
rapidio: add modular rapidio core build into powerpc and mips branches
partitions/efi: complete documentation of gpt kernel param purpose
kdump: add /sys/kernel/vmcoreinfo ABI documentation
kdump: fix exported size of vmcoreinfo note
kexec: add sysctl to disable kexec_load
fs/exec.c: call arch_pick_mmap_layout() only once
...
entirely of new platform/driver support. There are some conversions of
existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc tree
this pull request is broken into two pieces. The second piece will be
sent out after arm-soc sends you the pull request that merged in core
support for the HiSilicon 3620 platform. That same pull request from
arm-soc depends on this pull request to merge in those HiSilicon bits
without causing build failures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Hh66
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework changes from Mike Turquette:
"The first half of the clk framework pull request is made up almost
entirely of new platform/driver support. There are some conversions
of existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc
tree this pull request is broken into two pieces. The second piece
will be sent out after arm-soc sends you the pull request that merged
in core support for the HiSilicon 3620 platform. That same pull
request from arm-soc depends on this pull request to merge in those
HiSilicon bits without causing build failures"
[ Just did the ARM SoC merges, so getting ready for the second clk tree
pull request - Linus ]
* tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux: (97 commits)
devicetree: bindings: Document qcom,mmcc
devicetree: bindings: Document qcom,gcc
clk: qcom: Add support for MSM8660's global clock controller (GCC)
clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8974's global clock controller (GCC)
clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8960's global clock controller (GCC)
clk: qcom: Add reset controller support
clk: qcom: Add support for branches/gate clocks
clk: qcom: Add support for root clock generators (RCGs)
clk: qcom: Add support for phase locked loops (PLLs)
clk: qcom: Add a regmap type clock struct
clk: Add set_rate_and_parent() op
reset: Silence warning in reset-controller.h
clk: sirf: re-arch to make the codes support both prima2 and atlas6
clk: composite: pass mux_hw into determine_rate
clk: shmobile: Fix MSTP clock array initialization
clk: shmobile: Fix MSTP clock index
ARM: dts: Add clock provider specific properties to max77686 node
clk: max77686: Register OF clock provider
...
The file uses u16 type but doesn't include its definition explicitly
I was getting this error when including this header in my driver:
arch/mips/include/asm/mipsregs.h:644:33: error: unknown type name ‘u16’
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Steven J. Hill <Steven.Hill@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6212/
Update the early_printk code to include linux/serial_bcm63xx.h which
provides the definitions for the UART block registers. While at it,
remove the inclusion of serial_bcm63xx.h which was just there to allow
smooth transition.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6203/
Move the BCM63XX UART driver definitions to
include/linux/serial_bcm63xx.h such that we do not rely on the MIPS
BCM63XX code to provide these for us.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6202/
This will be needed by the next patch to use said nodes for probing
via the device tree.
Signed-off-by: David Daney <david.daney@cavium.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6185/
This patch causes the kernel to mux the SERIRQ interrupt to the SERIRQ
pin of the PIIX4 and to enable that interrupt. The kernel depends upon
the interrupt when using the SuperIO UARTs (ttyS0 & ttyS1) but
previously would not configure it, instead relying upon the bootloader
having done so. If that is not the case then the typical result is that
the system appears to hang once it reaches userland as no output is
displayed on the UART.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6182/
The following build error is seen if CONFIG_32BIT is undefined,
CONFIG_64BIT is defined, and CONFIG_MIPS32_O32 is undefined.
asm/syscall.h: In function 'mips_get_syscall_arg':
arch/mips/include/asm/syscall.h:32:16: error: unused variable 'usp' [-Werror=unused-variable]
cc1: all warnings being treated as errors
Fixes: c0ff3c53d4 ('MIPS: Enable HAVE_ARCH_TRACEHOOK')
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6160/
The linux build-bot recently reported a build error in arch/mips/kernel/vpe.c
tree: git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace.git for-linus
head: 261000a56b
commit: 261000a56b [4/4] userns: userns: Remove UIDGID_STRICT_TYPE_CHECKS
config: make ARCH=mips maltaaprp_defconfig
All error/warnings:
arch/mips/kernel/vpe.c: In function 'vpe_open':
>> arch/mips/kernel/vpe.c:1086:9: error: incompatible types when assigning to type 'unsigned int' from type 'kuid_t'
>> arch/mips/kernel/vpe.c:1087:9: error: incompatible types when assigning to type 'unsigned int' from type 'kgid_t'
vim +1086 arch/mips/kernel/vpe.c
863abad4 Jesper Juhl 2010-10-30 1080 return -ENOMEM;
863abad4 Jesper Juhl 2010-10-30 1081 }
e01402b1 Ralf Baechle 2005-07-14 1082 v->plen = P_SIZE;
e01402b1 Ralf Baechle 2005-07-14 1083 v->load_addr = NULL;
e01402b1 Ralf Baechle 2005-07-14 1084 v->len = 0;
e01402b1 Ralf Baechle 2005-07-14 1085
d76b0d9b David Howells 2008-11-14 @1086 v->uid = filp->f_cred->fsuid;
d76b0d9b David Howells 2008-11-14 @1087 v->gid = filp->f_cred->fsgid;
2600990e Ralf Baechle 2006-04-05 1088
2600990e Ralf Baechle 2006-04-05 1089 v->cwd[0] = 0;
2600990e Ralf Baechle 2006-04-05 1090 ret = getcwd(v->cwd, VPE_PATH_MAX);
When examining the code to see what v->uid and v->gid were used for I
discovered that the only users in the kernel are vpe_getuid and
vpe_getgid, and that vpe_getuid and vpe_getgid are never called.
So instead of proposing a conversion to use kuid_t and kgid_t instead
of unsigned int/int as I normally would let's just kill this dead code
so no one has to worry about it further.
Deng-Cheng Zhu said:
This is a good catch. vpe_get[u|g]id was originally used by KSPD which
has been removed.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Reviewed-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Only one MIPS development board actually supports enabling/disabling DMA
coherency at runtime, so it's not a good idea to push the overhead of
checking that configuration setting onto every other supported target as
well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5912/
Clean-up code according to the 'checkpatch.pl' script.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6097/
Reviewed-by: John Crispin <blogic@openwrt.org>
Malta with multi-core CM platforms can now use APRP functionality.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6096/
This patch adds RTLX API support for platforms having a CMP.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6095/
Reviewed-by: John Crispin <blogic@openwrt.org>
Split the RTLX functionality in preparation for adding support for CMP
platforms. Common functions remain in the original file and a new file
contains code specific to platforms that do not have a CMP.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6093/
Reviewed-by: John Crispin <blogic@openwrt.org>
Split the VPE functionality in preparation for adding support
for CMP platforms. Common functions remain in the original file
and a new file contains code specific to platforms that do not
have a CMP present.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6094/
The interAptiv is a power-efficient multi-core microprocessor
for use in system-on-chip (SoC) applications. The interAptiv combines
a multi-threading pipeline with a coherence manager to deliver improved
computational throughput and power efficiency. The interAptiv can
contain one to four MIPS32R3 interAptiv cores, system level
coherence manager with L2 cache, optional coherent I/O port,
and optional floating point unit.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6163/
Add processor identifiers for UP and MT interAptiv processors.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6151/
The Fixed Page Size TLB (FTLB) is a set-associative dual entry TLB. Its
purpose is to reduce the number of TLB misses by increasing the effective
TLB size and keep the implementation complexity to minimum levels.
A supported core can have both VTLB and FTLB.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6139/
The proAptiv Multiprocessing System is a power efficient multi-core
microprocessor for use in system-on-chip (SoC) applications.
The proAptiv Multiprocessing System combines a deep pipeline
with multi-issue out of order execution for improved computational
throughput. The proAptiv Multiprocessing System can contain one to
six MIPS32r3 proAptiv cores, system level coherence
manager with L2 cache, optional coherent I/O port, and optional
floating point unit.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6134/
Add processor identifiers for single core and multi-core
proAptiv processors.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6133/
For MIPS32R3 supported cores, the EHINV bit needs to be set when
invalidating the TLB. This is necessary because the legacy software
method of representing an invalid TLB entry using an unmapped address
value is not guaranteed to work.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6132/
MIPS32R3 introduced a new set of Segmentation Control registers which
increase the flexibility of the segmented-based memory scheme.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6131/
New Aptiv cores support the TLBINVF instruction for flushing
the VTLB.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6130/
The UNIQUE_ENTRYHI definition was duplicated whenever there
was the need to flush the TLB entries. We move this common
definition to a header file.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6129/
The BCM47XX SoC code missed a cpu-feature-overrides.h header file, this
patch adds it. This code supports a long line of SoCs with different
features so for some features we still have to rely on the runtime
detection.
This was crated by checking the features of a BCM4712, BCM4704,
BCM5354, BCM4716 and BCM4706 SoC and then tested on these SoCs. There
are some SoCs missing but I hope they do not have any more or less
features.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6289/
Recently the output of "system type" in /proc/cpuinfo was changed to
Broadcom BCM4730 (Some sample board), but it is better to just print
the SoC name in the "system type" entry. The board name will be added
in the machine entry later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5865/
BMIPS32 and BMIPS3300 also need to be available for MIPS32R1, as
bcm47xx might not select BMIPS.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6245/
Add a helper similar to the generic register_XXX_smp_ops() for bmips.
Register SMP UP ops in case of BMIPS32/3300.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6248/
Allow building for all bmips cpus at the same time by changing ifdefs
to checks for the cpu type, or adding appropriate checks to the
assembly.
Since BMIPS43XX and BMIPS5000 require different IPI implementations,
split the SMP ops into one for each, so the runtime overhead is only
at registration time for them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6241/
Add guards around the enum to allow including cpu.h from assembly.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6238/
Pull core locking changes from Ingo Molnar:
- futex performance increases: larger hashes, smarter wakeups
- mutex debugging improvements
- lots of SMP ordering documentation updates
- introduce the smp_load_acquire(), smp_store_release() primitives.
(There are WIP patches that make use of them - not yet merged)
- lockdep micro-optimizations
- lockdep improvement: better cover IRQ contexts
- liblockdep at last. We'll continue to monitor how useful this is
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
futexes: Fix futex_hashsize initialization
arch: Re-sort some Kbuild files to hopefully help avoid some conflicts
futexes: Avoid taking the hb->lock if there's nothing to wake up
futexes: Document multiprocessor ordering guarantees
futexes: Increase hash table size for better performance
futexes: Clean up various details
arch: Introduce smp_load_acquire(), smp_store_release()
arch: Clean up asm/barrier.h implementations using asm-generic/barrier.h
arch: Move smp_mb__{before,after}_atomic_{inc,dec}.h into asm/atomic.h
locking/doc: Rename LOCK/UNLOCK to ACQUIRE/RELEASE
mutexes: Give more informative mutex warning in the !lock->owner case
powerpc: Full barrier for smp_mb__after_unlock_lock()
rcu: Apply smp_mb__after_unlock_lock() to preserve grace periods
Documentation/memory-barriers.txt: Downgrade UNLOCK+BLOCK
locking: Add an smp_mb__after_unlock_lock() for UNLOCK+BLOCK barrier
Documentation/memory-barriers.txt: Document ACCESS_ONCE()
Documentation/memory-barriers.txt: Prohibit speculative writes
Documentation/memory-barriers.txt: Add long atomic examples to memory-barriers.txt
Documentation/memory-barriers.txt: Add needed ACCESS_ONCE() calls to memory-barriers.txt
Revert "smp/cpumask: Make CONFIG_CPUMASK_OFFSTACK=y usable without debug dependency"
...
For user space packet capturing libraries such as libpcap, there's
currently only one way to check which BPF extensions are supported
by the kernel, that is, commit aa1113d9f8 ("net: filter: return
-EINVAL if BPF_S_ANC* operation is not supported"). For querying all
extensions at once this might be rather inconvenient.
Therefore, this patch introduces a new option which can be used as
an argument for getsockopt(), and allows one to obtain information
about which BPF extensions are supported by the current kernel.
As David Miller suggests, we do not need to define any bits right
now and status quo can just return 0 in order to state that this
versions supports SKF_AD_PROTOCOL up to SKF_AD_PAY_OFFSET. Later
additions to BPF extensions need to add their bits to the
bpf_tell_extensions() function, as documented in the comment.
Signed-off-by: Michal Sekletar <msekleta@redhat.com>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, Loongson-2 call protected_blast_icache_range() and others
call protected_loongson23_blast_icache_range(), but I think the correct
behavior should be the opposite. BTW, Loongson-3's cache-ops is
compatible with MIPS64, but not compatible with Loongson-2. So, rename
xxx_loongson23_yyy things to xxx_loongson2_yyy.
The patch fixes early boot hang with 3.13-rc1, introduced in commit
14bd8c0820 ("MIPS: Loongson: Get rid of Loongson 2 #ifdefery all over
arch/mips").
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CPUs implementing MIPS32 R2 may include a 64-bit FPU, just as MIPS64 CPUs
do. In order to preserve backwards compatibility a 64-bit FPU will act
like a 32-bit FPU (by accessing doubles from the least significant 32
bits of an even-odd pair of FP registers) when the Status.FR bit is
zero, again just like a mips64 CPU. The standard O32 ABI is defined
expecting a 32-bit FPU, however recent toolchains support use of a
64-bit FPU from an O32 MIPS32 executable. When an ELF executable is
built to use a 64-bit FPU a new flag (EF_MIPS_FP64) is set in the ELF
header.
With this patch the kernel will check the EF_MIPS_FP64 flag when
executing an O32 binary, and set Status.FR accordingly. The addition
of O32 64-bit FP support lessens the opportunity for optimisation in
the FPU emulator, so a CONFIG_MIPS_O32_FP64_SUPPORT Kconfig option is
introduced to allow this support to be disabled for those that don't
require it.
Inspired by an earlier patch by Leonid Yegoshin, but implemented more
cleanly & correctly.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/6154/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for microMIPS encodings of the mfhc1 & mthc1
instructions introduced in release 2 of the mips32 & mips64
architectures, converting them to their mips32 equivalents for the FPU
emulator.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the mfhc1 & mthc1 instructions to the FPU
emulator. These instructions were introduced in release 2 of the MIPS32
& MIPS64 architectures and allow access to the most significant 32 bits
of a 64-bit FP register.
[ralf@linux-mips.org: Fix ifdef hell added by original patch.]
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A number of situations currently require the heavyweight smp_mb(),
even though there is no need to order prior stores against later
loads. Many architectures have much cheaper ways to handle these
situations, but the Linux kernel currently has no portable way
to make use of them.
This commit therefore supplies smp_load_acquire() and
smp_store_release() to remedy this situation. The new
smp_load_acquire() primitive orders the specified load against
any subsequent reads or writes, while the new smp_store_release()
primitive orders the specifed store against any prior reads or
writes. These primitives allow array-based circular FIFOs to be
implemented without an smp_mb(), and also allow a theoretical
hole in rcu_assign_pointer() to be closed at no additional
expense on most architectures.
In addition, the RCU experience transitioning from explicit
smp_read_barrier_depends() and smp_wmb() to rcu_dereference()
and rcu_assign_pointer(), respectively resulted in substantial
improvements in readability. It therefore seems likely that
replacing other explicit barriers with smp_load_acquire() and
smp_store_release() will provide similar benefits. It appears
that roughly half of the explicit barriers in core kernel code
might be so replaced.
[Changelog by PaulMck]
Reviewed-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Victor Kaplansky <VICTORK@il.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20131213150640.908486364@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds common __clk_get(), __clk_put() clkdev helpers that
replace their platform specific counterparts when the common clock
API is used.
The owner module pointer field is added to struct clk so a reference
to the clock supplier module can be taken by the clock consumers.
The owner module is assigned while the clock is being registered,
in functions _clk_register() and __clk_register().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull irq cleanups from Ingo Molnar:
"This is a multi-arch cleanup series from Thomas Gleixner, which we
kept to near the end of the merge window, to not interfere with
architecture updates.
This series (motivated by the -rt kernel) unifies more aspects of IRQ
handling and generalizes PREEMPT_ACTIVE"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
preempt: Make PREEMPT_ACTIVE generic
sparc: Use preempt_schedule_irq
ia64: Use preempt_schedule_irq
m32r: Use preempt_schedule_irq
hardirq: Make hardirq bits generic
m68k: Simplify low level interrupt handling code
genirq: Prevent spurious detection for unconditionally polled interrupts
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
side: the HV and emulation flavors can now coexist in a single kernel
is probably the most interesting change from a user point of view.
On the x86 side there are nested virtualization improvements and a
few bugfixes. ARM got transparent huge page support, improved
overcommit, and support for big endian guests.
Finally, there is a new interface to connect KVM with VFIO. This
helps with devices that use NoSnoop PCI transactions, letting the
driver in the guest execute WBINVD instructions. This includes
some nVidia cards on Windows, that fail to start without these
patches and the corresponding userspace changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=rWNf
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM changes from Paolo Bonzini:
"Here are the 3.13 KVM changes. There was a lot of work on the PPC
side: the HV and emulation flavors can now coexist in a single kernel
is probably the most interesting change from a user point of view.
On the x86 side there are nested virtualization improvements and a few
bugfixes.
ARM got transparent huge page support, improved overcommit, and
support for big endian guests.
Finally, there is a new interface to connect KVM with VFIO. This
helps with devices that use NoSnoop PCI transactions, letting the
driver in the guest execute WBINVD instructions. This includes some
nVidia cards on Windows, that fail to start without these patches and
the corresponding userspace changes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (146 commits)
kvm, vmx: Fix lazy FPU on nested guest
arm/arm64: KVM: PSCI: propagate caller endianness to the incoming vcpu
arm/arm64: KVM: MMIO support for BE guest
kvm, cpuid: Fix sparse warning
kvm: Delete prototype for non-existent function kvm_check_iopl
kvm: Delete prototype for non-existent function complete_pio
hung_task: add method to reset detector
pvclock: detect watchdog reset at pvclock read
kvm: optimize out smp_mb after srcu_read_unlock
srcu: API for barrier after srcu read unlock
KVM: remove vm mmap method
KVM: IOMMU: hva align mapping page size
KVM: x86: trace cpuid emulation when called from emulator
KVM: emulator: cleanup decode_register_operand() a bit
KVM: emulator: check rex prefix inside decode_register()
KVM: x86: fix emulation of "movzbl %bpl, %eax"
kvm_host: typo fix
KVM: x86: emulate SAHF instruction
MAINTAINERS: add tree for kvm.git
Documentation/kvm: add a 00-INDEX file
...
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
glibc recently changed the error string for ESTALE to remove "NFS" -
https://sourceware.org/git/?p=glibc.git;a=commitdiff;h=96945714ec61951cc748da2b4b8a80cf02127ee9
from: [ERR_REMAP (ESTALE)] = N_("Stale NFS file handle"),
to: [ERR_REMAP (ESTALE)] = N_("Stale file handle"),
And some have expressed concern that the kernel's errno.h
comments still refer to NFS.
So make that change... note that this is a comment-only change,
and has no functional difference.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Pull scheduler changes from Ingo Molnar:
"The main changes in this cycle are:
- (much) improved CONFIG_NUMA_BALANCING support from Mel Gorman, Rik
van Riel, Peter Zijlstra et al. Yay!
- optimize preemption counter handling: merge the NEED_RESCHED flag
into the preempt_count variable, by Peter Zijlstra.
- wait.h fixes and code reorganization from Peter Zijlstra
- cfs_bandwidth fixes from Ben Segall
- SMP load-balancer cleanups from Peter Zijstra
- idle balancer improvements from Jason Low
- other fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
ftrace, sched: Add TRACE_FLAG_PREEMPT_RESCHED
stop_machine: Fix race between stop_two_cpus() and stop_cpus()
sched: Remove unnecessary iteration over sched domains to update nr_busy_cpus
sched: Fix asymmetric scheduling for POWER7
sched: Move completion code from core.c to completion.c
sched: Move wait code from core.c to wait.c
sched: Move wait.c into kernel/sched/
sched/wait: Fix __wait_event_interruptible_lock_irq_timeout()
sched: Avoid throttle_cfs_rq() racing with period_timer stopping
sched: Guarantee new group-entities always have weight
sched: Fix hrtimer_cancel()/rq->lock deadlock
sched: Fix cfs_bandwidth misuse of hrtimer_expires_remaining
sched: Fix race on toggling cfs_bandwidth_used
sched: Remove extra put_online_cpus() inside sched_setaffinity()
sched/rt: Fix task_tick_rt() comment
sched/wait: Fix build breakage
sched/wait: Introduce prepare_to_wait_event()
sched/wait: Add ___wait_cond_timeout() to wait_event*_timeout() too
sched: Remove get_online_cpus() usage
sched: Fix race in migrate_swap_stop()
...
The early_init_devtree() API was removed in linux-next for 3.13 with
commit "mips: use early_init_dt_scan". This causes Netlogic XLP compile
to fail:
arch/mips/netlogic/xlp/setup.c:101: undefined reference to `early_init_devtree'
Add xlp_early_init_devtree() which uses the __dt_setup_arch() to
handle early device tree related initialization to fix this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Another whitespace clean-up, this removes tabs from between sentences in
some comments.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6103/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PIIX4_ICTLR* and PIIX4_OCW* defines are not used by any other files.
Remove them.
The only file (other than fixup-malta.c which includes piix4.h in patch #1)
containing "#include <asm/mips-boards/piix4.h>" is
arch/mips/mti-malta/malta-int.c whose first version is actually
"1da177e4c3:arch/mips/mips-boards/malta/malta_int.c". In that version, in
the function get_int(), things in piix4.h are used. But now malta-int.c no
longer needs those stuff.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make the code more readable by using defines.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6031/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Always register the R4K clocksource when CONFIG_CSRC_R4K is selected,
regardless of selected support for other clocksources. The kernel will
select the best clocksource based on their ratings, making it safe to
register R4K unconditionally and use it as a fallback should the
kernel be run on a system where other selected clocksources are
inoperable.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6024/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nobody seems to care about this platform anymore and my attempts to find
somebody willing to provide some tlc for PowerTV have failed so far.
So let's nuke the bloody thing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5910/
Allow usage of scratch register for current pgd even when
MIPS_PGD_C0_CONTEXT is not configured. MIPS_PGD_C0_CONTEXT is set
for 64r2 platforms to indicate availability of Xcontext for saving
cpuid, thus freeing Context to be used for saving PGD. This option
was also tied to using a scratch register for storing PGD.
This commit will allow usage of scratch register to store the current
pgd if one can be allocated for the platform, even when
MIPS_PGD_C0_CONTEXT is not set. The cpuid will be kept in the CP0
Context register in this case.
The code to store the current pgd for the TLB miss handler is now
generated in all cases. When scratch register is available, the PGD
is also stored in the scratch register.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/5906/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change complements commits d0da7c002f7b2a93582187a9e3f73891a01d8ee4
[MIPS: DEC: Convert to new irq_chip functions] and
5359b938c0 [MIPS: DECstation I/O ASIC DMA
interrupt handling fix] and implements automatic handling of the two
classes of DMA interrupts the I/O ASIC implements, informational and
errors.
Informational DMA interrupts do not stop the transfer and use the
`handle_edge_irq' handler that clears the request right away so that
another request may be recorded while the previous is being handled.
DMA error interrupts stop the transfer and require a corrective action
before DMA can be reenabled. Therefore they use the `handle_fasteoi_irq'
handler that only clears the request on the way out. Because MIPS
processor interrupt inputs, one of which the I/O ASIC's interrupt
controller is cascaded to, are level-triggered it is recommended that
error DMA interrupt action handlers are registered with the IRQF_ONESHOT
flag set so that they are run with the interrupt line masked.
This change removes the export of clear_ioasic_dma_irq that now does not
have to be called by device drivers to clear interrupts explicitly
anymore. Originally these interrupts were cleared in the .end handler of
the `irq_chip' structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The semantics stay the same - on Cavium Octeon the functions were dead
code (it overrides the MIPS DMA ops) - on other platforms they contained
no code at all.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5720/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The nvram contains some gpio configuration for boards. It is stored in
a gpio<number>=name format e.g.
gpio8=wps_button
gpio4=robo_reset
This patches adds a function to parse these entries, so other driver
can use it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect on which board this code is running based on some nvram
settings. This is needed to start board specific workarounds and
configure the leds and buttons which are on different gpios on every board.
This patches add some boards we have seen, but there are many more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5840
Patchwork: https://patchwork.linux-mips.org/patch/5855/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The definition of the CP0 register used to save the smp processor
id is repicated in many files, move them all to thread_info.h.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In commit 15ef17f622
(tty: ar933x_uart: use the clk API to get the uart
clock), the AR933x UART driver for has been converted
to get the uart clock rate via the clock API and it
does not use the platform data anymore.
Remove the ar933x_uart_platform.h header file and get
rid of the superfluous variable and initialization code
in platform setup.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5832/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now when the main kvm code relying on these defines has been moved to
the x86 specific part of the world, we can get rid of these.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Fengguang Wu, Oleg Nesterov and Peter Zijlstra tracked down
a kernel crash to a GCC bug: GCC miscompiles certain 'asm goto'
constructs, as outlined here:
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
Implement a workaround suggested by Jakub Jelinek.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Suggested-by: Jakub Jelinek <jakub@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implement pci_address_to_pio as weak function to remove the dependency on
asm/prom.h. This is in preparation to make prom.h optional.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Convert mips to use new early_init_dt_scan function.
Remove early_init_dt_scan_memory_arch
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Acked-by: John Crispin <blogic@openwrt.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSUc9zAAoJEHm+PkMAQRiG9DMH/AtpuAF6LlMRPjrCeuJQ1pyh
T0IUO+CsLKO6qtM5IyweP8V6zaasNjIuW1+B6IwVIl8aOrM+M7CwRiKvpey26ldM
I8G2ron7hqSOSQqSQs20jN2yGAqQGpYIbTmpdGLAjQ350NNNvEKthbP5SZR5PAmE
UuIx5OGEkaOyZXvCZJXU9AZkCxbihlMSt2zFVxybq2pwnGezRUYgCigE81aeyE0I
QLwzzMVdkCxtZEpkdJMpLILAz22jN4RoVDbXRa2XC7dA9I2PEEXI9CcLzqCsx2Ii
8eYS+no2K5N2rrpER7JFUB2B/2X8FaVDE+aJBCkfbtwaYTV9UYLq3a/sKVpo1Cs=
=xSFJ
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc4' into sched/core
Merge Linux v3.12-rc4 to fix a conflict and also to refresh the tree
before applying more scheduler patches.
Conflicts:
arch/avr32/include/asm/Kbuild
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
As mentioned in commit afe4fd0624 ("pkt_sched: fq: Fair Queue packet
scheduler"), this patch adds a new socket option.
SO_MAX_PACING_RATE offers the application the ability to cap the
rate computed by transport layer. Value is in bytes per second.
u32 val = 1000000;
setsockopt(sockfd, SOL_SOCKET, SO_MAX_PACING_RATE, &val, sizeof(val));
To be effectively paced, a flow must use FQ packet scheduler.
Note that a packet scheduler takes into account the headers for its
computations. The effective payload rate depends on MSS and retransmits
if any.
I chose to make this pacing rate a SOL_SOCKET option instead of a
TCP one because this can be used by other protocols.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steinar H. Gunderson <sesse@google.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prepare to per-arch implementations of preempt_count move
the required bits into an asm-generic header and use this for all
archs.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-h5j0c1r3e3fk015m30h8f1zx@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ralf@linux-mips.org: This only matters to Alchemy platforms. On other
platforms fixup_bigphys_addr is just an identidy mapping.]
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Cc: tiejun.chen <tiejun.chen@windriver.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1868/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace hardcoded CP0 PRId and CP1 FPIR register access masks throughout.
The change does not touch places that use shifted or partial masks.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the CKSEG1ADDR macro when calculating VGA_MAP_MEM.
[ralf@linux-mips.org: Include <asm/addrspace.h for CKSEG1ADDR.]
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5814/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This essentially reverts commit efb9ca08b5
(kernel.org) / 58020a106879a8b372068741c81f0015c9b0b96dbv [[MIPS] Change
get_cycles to always return 0.]
Most users of get_cycles() invoke it as a timing interface. That's why
in modern kernels it was never very much missed for. /dev/random however
uses get_cycles() in the how the jitter in the interrupt timing contains
some useful entropy.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Move current_cpu_type() to a separate header file
o #ifdefing on supported CPU types lets modern GCC know that certain
code in callers may be discarded ideally turning current_cpu_type() into
a function returning a constant.
o Use current_cpu_type() rather than direct access to struct cpuinfo_mips.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5833/
boot_cpu_data is used the same as current_cpu_data but returns the CPU
data for CPU 0. This means it doesn't have to use smp_processor_id()
thus no need to disable preemption.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.
Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle). Otherwise the handler is
reentered over and over again.
The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared. Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'. Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Not all I/O ASIC versions have the free-running counter implemented, an
early revision used in the 5000/1xx models aka 3MIN and 4MIN did not have
it. Therefore we cannot unconditionally use it as a clock source.
Fortunately if not implemented its register slot has a fixed value so it
is enough if we check for the value at the end of the calibration period
being the same as at the beginning.
This also means we need to look for another high-precision clock source on
the systems affected. The 5000/1xx can have an R4000SC processor
installed where the CP0 Count register can be used as a clock source.
Unfortunately all the R4k DECstations suffer from the missed timer
interrupt on CP0 Count reads erratum, so we cannot use the CP0 timer as a
clock source and a clock event both at a time. However we never need an
R4k clock event device because all DECstations have a DS1287A RTC chip
whose periodic interrupt can be used as a clock source.
This gives us the following four configuration possibilities for I/O ASIC
DECstations:
1. No I/O ASIC counter and no CP0 timer, e.g. R3k 5000/1xx (3MIN).
2. No I/O ASIC counter but the CP0 timer, i.e. R4k 5000/150 (4MIN).
3. The I/O ASIC counter but no CP0 timer, e.g. R3k 5000/240 (3MAX+).
4. The I/O ASIC counter and the CP0 timer, e.g. R4k 5000/260 (4MAX+).
For #1 and #2 this change stops the I/O ASIC free-running counter from
being installed as a clock source of a 0Hz frequency. For #2 it also
arranges for the CP0 timer to be used as a clock source rather than a
clock event device, because having an accurate wall clock is more
important than a high-precision interval timer. For #3 there is no
change. For #4 the change makes the I/O ASIC free-running counter
installed as a clock source so that the CP0 timer can be used as a clock
event device.
Unfortunately the use of the CP0 timer as a clock event device relies on a
succesful completion of c0_compare_interrupt. That never happens, because
while waiting for a CP0 Compare interrupt to happen the function spins in
a loop reading the CP0 Count register. This makes the CP0 Count erratum
trigger reliably causing the interrupt waited for to be lost in all cases.
As a result #4 resorts to using the CP0 timer as a clock source as well,
just as #2. However we want to keep this separate arrangement in case
(hope) c0_compare_interrupt is eventually rewritten such that it avoids
the erratum.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5825/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This has been sitting in -next for a while with no objections and all
MIPS defconfigs except one are building fine; that one platform got
broken by another patch in your tree and I'm going to submit a patch
separately.
- a handful of fixes that didn't make 3.11
- a few bits of Octeon 3 support with more to come for a later
release
- platform enhancements for Octeon, ath79, Lantiq, Netlogic and
Ralink SOCs
- a GPIO driver for the Octeon
- some dusting off of the DECstation code
- the usual dose of cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits)
MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code
MIPS: kexec: Fix random crashes while loading crashkernel
MIPS: kdump: Skip walking indirection page for crashkernels
MIPS: DECstation HRT calibration bug fixes
MIPS: Export copy_from_user_page() (needed by lustre)
MIPS: Add driver for the built-in PCI controller of the RT3883 SoC
MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000
MIPS: ralink: Add support for reset-controller API
MIPS: ralink: mt7620: Add cpu-feature-override header
MIPS: ralink: mt7620: Add spi clock definition
MIPS: ralink: mt7620: Add wdt clock definition
MIPS: ralink: mt7620: Improve clock frequency detection
MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts
MIPS: ralink: mt7620: Add verbose ram info
MIPS: ralink: Probe clocksources from OF
MIPS: ralink: Add support for systick timer found on newer ralink SoC
MIPS: ralink: Add support for periodic timer irq
MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards
MIPS: Netlogic: Add support for USB on XLP2xx
MIPS: Netlogic: XLP2xx update for I2C controller
...
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iEYEABECAAYFAlIt3VsACgkQdwG7hYl686NKBQCgqFzV1S+TiXZSjbqanK0374Hu
lMIAoI2IOQb1bgQFSqaOzgSaBmVhLtMc
=xWBt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd
Pull mtd updates from David Woodhouse:
- factor out common code from MTD tests
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc
* tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd: (184 commits)
mtd: chips: Add support for PMC SPI Flash chips in m25p80.c
mtd: ofpart: use for_each_child_of_node() macro
mtd: mtdswap: replace strict_strtoul() with kstrtoul()
mtd cs553x_nand: use kzalloc() instead of memset
mtd: atmel_nand: fix error return code in atmel_nand_probe()
mtd: bcm47xxsflash: writing support
mtd: bcm47xxsflash: implement erasing support
mtd: bcm47xxsflash: convert to module_platform_driver instead of init/exit
mtd: bcm47xxsflash: convert kzalloc to avoid invalid access
mtd: remove alauda driver
mtd: nand: mxc_nand: mark 'const' properly
mtd: maps: cfi_flagadm: add missing __iomem annotation
mtd: spear_smi: add missing __iomem annotation
mtd: r852: Staticize local symbols
mtd: nandsim: Staticize local symbols
mtd: impa7: add missing __iomem annotation
mtd: sm_ftl: Staticize local symbols
mtd: m25p80: add support for mr25h10
mtd: m25p80: make CONFIG_M25PXX_USE_FAST_READ safe to enable
mtd: m25p80: Pass flags through CAT25_INFO macro
...
Override certain CPU features to help GCC to optimize
the generated code. Saves about 150KB in the vmlinux
image with a generic configuration.
text data bss dec hex filename
3824158 134820 234192 4193170 3ffb92 vmlinux.no-override
3664054 138804 234192 4037050 3d99ba vmlinux.override
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code assumes that the peripheral clock always
runs at 40MHz which is not true in all configuration. The
peripheral clock can also use the reference clock instead
of the fixed 40MHz rate. If the reference clock runs at a
different rate, various peripheries are behaving incorrectly.
Additionally, the currectly calculated system clock is also
wrong. The actual value what the code computes is the rate
of the DRAM which can be different from the system clock.
Add new helper functions to get the rate of the different
clocks and use the correct values for the registered clock
devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5755/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add USB intialization code to handle the new XLP2XX USB 3.0 block.
This adds xlp/usb-init-xlp2.c to initialize the XLP2XX USB glue-logic
for XHCI and EHCI. Interrupt and IO offset code in xlp-hal/iomap.h
and xlp/nlm_hal.c is also updated for the new USB block.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5744/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
XLP2xx has a new I2C controller which has 4 buses connected to
it. Update the IO offset and IRQ mapping code to reflect this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add code to calculate the CPU and PIC frequency for XLP2XX SoCs.
Since the PIC frequency on XLP2XX can be configured, add a new macro
pic_timer_freq() to be used in netlogic/common/time.c.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5701/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
XLP2XX is first in the series of 28nm XLPII processors.
The changes are to:
* Add processor ID for XLP2XX to asm/cpu.h and kernel/cpu-probe.c.
* Add a cpu_is_xlpii() function to check for XLPII processors.
* Update xlp_mmu_init() to use config4 to enable extended TLB.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Read the memory from the Bridge DRAM BARs, if it is not passed in
from the device tree. This will allow us to remove memory configuration
from built in device trees.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5743/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ath79 code supports various SoCs which are using either a 24Kc
or a 74Kc core. The 74Kc core has DSP support, so don't hardwire
the values to zero.
Commit 00dc5ce2a6 (MIPS: ath79: don't
hardcode the unavailability of the DSP ASE) has fixed this already,
but that change got reverted by 475032564e
(MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.)
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5750/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 02b849f761 ("MIPS: Get rid of the
use of .macro in C code.") replaced the macro usage but missed
the accessors in bmips.h, causing the following build error:
CC arch/mips/kernel/smp-bmips.o
{standard input}: Assembler messages:
{standard input}:951: Error: Unrecognized opcode `_ssnop'
{standard input}:952: Error: Unrecognized opcode `_ssnop'
(...)
make[6]: *** [arch/mips/kernel/smp-bmips.o] Error 1
Fix by rewriting the inline assembler using existing inline functions.
The generated code should stay unchanged.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5644/
Reviewed-by: Jonas Gorski <jogo@openwrt.org>
Use generic-y and remove headers in arch/mips/include/[uapi/]asm/Kbuild
where the header just includes or is identical to the corresponding
<asm-generic/*.h>.
We can't do the same for uapi/asm/kvm_para.h because it's presence is
explicitly checked in include/uapi/linux/Kbuild to decide whether to add
kvm_para.h to header-y.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Dave Jones <davej@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: David Sharp <dhsharp@google.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5581/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ve9i
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Until now, the MSI architecture-specific functions could be overloaded
using a fairly complex set of #define and compile-time
conditionals. In order to prepare for the introduction of the msi_chip
infrastructure, it is desirable to switch all those functions to use
the 'weak' mechanism. This commit converts all the architectures that
were overidding those MSI functions to use the new strategy.
Note that we keep two separate, non-weak, functions
default_teardown_msi_irqs() and default_restore_msi_irqs() for the
default behavior of the arch_teardown_msi_irqs() and
arch_restore_msi_irqs(), as the default behavior is needed by x86 PCI
code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Daniel Price <daniel.price@gmail.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
It wasn't until GCC 4.3 I believe that the __SIZEOF_*__ predefined macros
were added. The change below switches <uapi/asm/siginfo.h> to the
_MIPS_SZLONG macro so that compilation with e.g. GCC 4.1.2 succeeds.
This is a user API header so I think this is even more important, for
older userland support. The change adds an unsuccessful default too, to
catch any compiler configuration oddities.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5630/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix build error below:
arch/mips/include/asm/mach-generic/spaces.h:29:0: warning:
"UNCAC_BASE" redefined [enabled by default]
In file included from arch/mips/include/asm/addrspace.h:13:0,
from arch/mips/include/asm/barrier.h:11,
from arch/mips/include/asm/bitops.h:18,
from include/linux/bitops.h:22,
from include/linux/kernel.h:10,
from include/asm-generic/bug.h:13,
from arch/mips/include/asm/bug.h:41,
from include/linux/bug.h:4,
from include/linux/page-flags.h:9,
from kernel/bounds.c:9:
arch/mips/include/asm/mach-ar7/spaces.h:20:0: note: this is the
location of the previous definition
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5583/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 3747069b25e419f6b51395f48127e9812abc3596 upstream.
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
Here, we remove all the MIPS __cpuinit from C code and __CPUINIT
from asm files. MIPS is interesting in this respect, because there
are also uasm users hiding behind their own renamed versions of the
__cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
[ralf@linux-mips.org: Folded in Paul's followup fix.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5494/
Patchwork: https://patchwork.linux-mips.org/patch/5495/
Patchwork: https://patchwork.linux-mips.org/patch/5509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Rename LL_SO to BUSY_POLL_SO
Rename sysctl_net_ll_{read,poll} to sysctl_busy_{read,poll}
Fix up users of these variables.
Fix documentation for sysctl.
a patch for the socket.7 man page will follow separately,
because of limitations of my mail setup.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Pull slave-dmaengine updates from Vinod Koul:
"Once you have some time from extended weekend celebrations please
consider pulling the following to get:
- Various fixes and PCI driver for dw_dmac by Andy
- DT binding for imx-dma by Markus & imx-sdma by Shawn
- DT fixes for dmaengine by Lars
- jz4740 dmac driver by Lars
- and various fixes across the drivers"
What "extended weekend celebrations"? I'm in the merge window, who has
time for extended celebrations..
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
DMA: shdma: add DT support
DMA: shdma: shdma_chan_filter() has to be in shdma-base.h
DMA: shdma: (cosmetic) don't re-calculate a pointer
dmaengine: at_hdmac: prepare clk before calling enable
dmaengine/trivial: at_hdmac: add curly brackets to if/else expressions
dmaengine: at_hdmac: remove unsuded atc_cleanup_descriptors()
dmaengine: at_hdmac: add FIFO configuration parameter to DMA DT binding
ARM: at91: dt: add header to define at_hdmac configuration
MIPS: jz4740: Correct clock gate bit for DMA controller
MIPS: jz4740: Remove custom DMA API
MIPS: jz4740: Register jz4740 DMA device
dma: Add a jz4740 dmaengine driver
MIPS: jz4740: Acquire and enable DMA controller clock
dma: mmp_tdma: disable irq when disabling dma channel
dmaengine: PL08x: Avoid collisions with get_signal() macro
dmaengine: dw: select DW_DMAC_BIG_ENDIAN_IO automagically
dma: dw: add PCI part of the driver
dma: dw: split driver to library part and platform code
dma: move dw_dmac driver to an own directory
dw_dmac: don't check resource with devm_ioremap_resource
...
Now that all users of the custom jz4740 DMA API have been converted to use
the dmaengine API instead we can remove the custom API and move all the code
talking to the hardware to the dmaengine driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
BCM6328 has a OTP which tells us if the second core is available.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/5490/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
