Pull input updates from Dmitry Torokhov:
"A few new drivers:
- driver for Azoteq IQS550/572/525 touch controllers
- driver for Microchip AT42QT1050 keys
- driver for GPIO controllable vibrators
- support for GT5663 in Goodix driver
... along with miscellaneous driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - mark expected switch fall-through
Input: qt1050 - add Microchip AT42QT1050 support
Input: add support for Azoteq IQS550/572/525
Input: add a driver for GPIO controllable vibrators
Input: synaptics-rmi4 - fix enum_fmt
Input: synaptics-rmi4 - fill initial format
HID: input: add mapping for KEY_KBD_LAYOUT_NEXT
Input: add KEY_KBD_LAYOUT_NEXT
Input: hyperv-keyboard - add module description
Input: olpc_apsp - depend on ARCH_MMP
Input: sun4i-a10-lradc-keys - add support for A83T
Input: snvs_pwrkey - use dev_pm_set_wake_irq() to simplify code
Input: lpc32xx-key - add clocks property and fix DT binding example
Input: i8042 - signal wakeup from atkbd/psmouse
Input: goodix - add GT5663 CTP support
Input: goodix - add regulators suppot
Input: evdev - use struct_size() in kzalloc() and vzalloc()
Input: edt-ft5x06 - convert to use SPDX identifier
Input: edt-ft5x06 - enable ACPI enumeration
This patch adds support for the Azoteq IQS550/572/525 family of
trackpad/touchscreen controllers.
The driver has been tested with an IQS550EV02 evaluation board. A
demonstration of the driver's capabilities is available here:
https://youtu.be/sRNNx4XZBts
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GT5663 is capacitive touch controller with customized smart
wakeup gestures.
Add support for it by adding compatible and supported chip data.
The chip data on GT5663 is similar to GT1151, like
- config data register has 0x8050 address
- config data register max len is 240
- config data checksum has 16-bit
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix CTP controllers require AVDD28, VDDIO regulators for power-on
sequence.
The delay between these regualtor operations as per Power-on Timing
from datasheet[1] is 0 (T1 >= 0 usec).
So, enable and disable these regulators in proper order using normal
regulator functions without any delay in between.
[1] GT5663 Datasheet_English_20151106_Rev.01
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- update the ili210x touchscreen driver, refreshing the code and adding
support for ILI251X line
- add support for st1633 to the st1232 touchscreen driver
- add support for sx8650 to the the sx8654 touchscreen driver
- add support for Evervision FT5726 to the edt-ft5x06 touchscreen
driver
- add support for gt5688 to the Goodix touchscreen driver
- new vibrator driver for MSM SOCs
- miscellaneous fixes for the rest of input drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
Input: wacom_serial4 - add support for Wacom ArtPad II tablet
Input: elan_i2c - add id for touchpad found in Lenovo s21e-20
Input: raspberrypi-ts - select CONFIG_INPUT_POLLDEV
Input: msm-vibrator - use correct gpio header
Input: ti_am335x_tsc - remove set but not used variable 'tscadc_dev'
Input: i8042 - rework DT node name comparisons
Input: goodix - print values in case of inconsistencies
Input: goodix - refer to touchscreen.txt in device tree bindings
Input: goodix - support Goodix gt5688
Input: synaptics_i2c - remove redundant spinlock
Input: db9 - mark expected switch fall-through
Input: qt2160 - remove redundant spinlock
Input: st1232 - handle common DT bindings
Input: ims-pcu - switch to using brightness_set_blocking()
Input: st1232 - switch to gpiod API
Input: ili210x - fetch touchscreen geometry from DT
Input: msm-vibrator - tweak an error message
Input: tm2-touchkey - acknowledge that setting brightness is a blocking call
Input: stmfts - acknowledge that setting brightness is a blocking call
Input: ili210x - switch to using devm_device_add_group()
...
When CONFIG_INPUT_POLLDEV is disabled, we get a link error:
drivers/input/touchscreen/raspberrypi-ts.o: In function `rpi_ts_probe':
raspberrypi-ts.c:(.text+0xec): undefined reference to `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0xec): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0x19c): undefined reference to `input_register_polled_device'
raspberrypi-ts.c:(.text+0x19c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `input_register_polled_device'
Select that symbol like we do from the other similar drivers.
Fixes: 0b9f28fed3 ("Input: add official Raspberry Pi's touchscreen driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
While here, correct MODULE_LICENSE() string to be aligned with license text.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ACPI allows to enumerate specific devices by using compatible strings.
Enable that enumeration for EDT touchscreen devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/input/touchscreen/ti_am335x_tsc.c: In function 'titsc_suspend':
drivers/input/touchscreen/ti_am335x_tsc.c:510:24: warning:
variable 'tscadc_dev' set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/ti_am335x_tsc.c: In function 'titsc_resume':
drivers/input/touchscreen/ti_am335x_tsc.c:527:24: warning:
variable 'tscadc_dev' set but not used [-Wunused-but-set-variable]
It's not used any more after 333e07ec4b ("Input: ti_am335x_tsc: Mark TSC
device as wakeup source")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"Invalid config" gives little idea what's wrong. Print the values that
must not be 0 so we know which ones are off.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is required to specify generic touchscreen properties via DT.
Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_gpiod_get_optional() and gpiod_set_value_cansleep() instead
of the old API. The st1232_ts_power() now passes on the inverted "poweron"
value to reflect the correct logical value.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fetching the geometry from the ILI251x registers seems unreliable and
sometimes returns all zeroes. Add support for fetching the geometry and
axis inversion from DT instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to turn regulators on and off when switching brightness, and
that may block, therefore we have to set stmfts_brightness_set() as
LED's brightness_set_blocking() method.
Fixes: 78bcac7b2a ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Acked-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By switching to devm_device_add_group() we can complete driver conversion
to using managed resources and get rid of ili210x_i2c_remove().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for ILI251x touch controller. This controller is similar
to the ILI210x, except for the following differences:
- Does not support I2C R-W transfer, Read must be followed by an
obscenely long delay, and then followed by Write
- Does support 10 simultaneous touch inputs.
- Touch data format is slightly different, pressure reporting does not
work although the touch data contain such information.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Perform the register access only after the I2C client data are set,
this is only done in preparation for the subsequent patch which
uses the I2C client data in the register IO function.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get rid of the packed structures for representing data as that does not
apply to other similar Ilitek touchscreens. Instead, implement a function
which parses the data and reports touch events and coordinates.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the driver to devm_request_irq(), drop the related unmanaged
deregistration code and add ili210x_irq_teardown() to tear the IRQ
down and cancel possible touchscreen pending work.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen can have a reset GPIO connected to it, add support
for such an arrangement.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The .get_pendown_state callback is set only by the platform data code,
which was just removed. Thus, get_pendown_state() always returns false,
so drop that altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is not a single user of the ili210x platform data in the kernel,
just drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should rely on the interrupt trigger (level vs edge) set up by the
firmware or board code instead of forcing what we consider appropriate.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some of the #defined register values are one-bit flags. Convert them to
use the BIT(x) macro instead of 1 byte hexadecimal values. This improves
readability and clarifies the intent.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
of_touchscreen.c provides a common interface for a axis inversion and
swapping of touchscreens. Therefore use it in the sx8654 driver.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sx8654 and sx8650 are quite similar, therefore add support for the
sx8650 within the sx8654 driver.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[dtor: use __be16 in sx8650_irq, add missing del_timer_sync]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the sx865[456] share the same datasheet and differ only in the
presence of a "capacitive proximity detection circuit" and a "haptics
motor driver for LRA/ERM" add them to the compatbiles. As the driver
doesn't implement these features it should be no problem.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sx8654 features a NRST input which may be connected to a GPIO.
Therefore add support for hard-resetting the sx8654 via this NRST.
If the reset-gpio property is provided the sx8654 is resetted via NRST
instead of the soft-reset via I2C.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds myself as an author of the st1232 driver module as Tony's
email address doesn't seem to work anymore.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the Sitronix ST1633 touchscreen controller to the st1232
driver. A protocol spec can be found here:
www.ampdisplay.com/documents/pdf/AM-320480B6TZQW-TC0H.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fixup for the input_event fix for y2038 Sparc64, and couple other
minor fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: input_event - fix the CONFIG_SPARC64 mixup
Input: olpc_apsp - assign priv->dev earlier
Input: uinput - fix undefined behavior in uinput_validate_absinfo()
Input: raspberrypi-ts - fix link error
Input: xpad - add support for SteelSeries Stratus Duo
Input: input_event - provide override for sparc64
This patch removes common ADC settings in favor to use
stmpe811_adc_common_init that is present in MFD. This is necessary in
preparation for the stmpe-adc driver, because those two drivers have
common settings for the ADC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move defines that are ADC related to the header of the overlying MFD,
so they can be used from multiple sub-devices.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwgIJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0F4H/jwv83AI9qxd4Zsj
geztCq0w1Vc48Gz/yDvl5MxZ74//q7Wz01qRTKisMNJla+Z0VuUReL12w0BGT0ko
ZwPqrvPtM04pA7A6J+vLM8t6k7Ck0q7xC3z/Y9eN5qxtC7yOX/X8RziiXBmyMzM5
nVpFYQwlk9/hSUHjPwMgf2dV32vNYl3FEph3g6nrqQLLdtsHiii9N8rC+cAU2jKg
sZ8Cp6REYYxt9LWEilsGof+oLnH+oUkXecB7WKKvSaAVHqR20xdpZ3ZvRcVyLfQ4
XCXBu8PIYYBWsa/iwuu0h4NuosGzEYbWOjnXKozOaV2KoqCT/Rk1egKIgb55EpyA
kFH4wfc=
=WAE7
-----END PGP SIGNATURE-----
Merge tag 'v4.20' into for-linus
Sync with mainline to get linux/overflow.h among other things.
Fix link error when TOUCHSCREEN_RASPBERRYPI_FW is enabled as a module and
the dependent module is built-in. The 'depends on RASPBERRYPI_FIRMWARE' by
itself prevents the touchscreen driver from being built-in when the
firmware is configured as a module. However, the '|| COMPILE_TEST' still
allows it unless we explicitly prevent that configuration with
'|| (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)'.
ld: drivers/input/touchscreen/raspberrypi-ts.o: in function `rpi_ts_probe':
raspberrypi-ts.c:(.text+0x3a8): undefined reference to `rpi_firmware_get'
ld: raspberrypi-ts.c:(.text+0x3a8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `rpi_firmware_get'
ld: raspberrypi-ts.c:(.text+0x4c8): undefined reference to `rpi_firmware_property'
ld: raspberrypi-ts.c:(.text+0x4c8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `rpi_firmware_property'
Rework so that TOUCHSCREEN_RASPBERRYPI_FW depends on
RASPBERRYPI_FIRMWARE=n if COMPILE_TEST is enabled.
Fixes: 0b9f28fed3 ("Input: add official Raspberry Pi's touchscreen driver")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately the evervision focaltech implementation uses two offset
registers, one for the x coordinate and one for y.
This patch extends the driver to handle those offset registers only for
devices that support these.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently only the threshold and gain parameters can be read.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Evervision displays are using different Focaltech touchscreen
controllers. This commit adds the initial support for the ones using the
FT5726 controller. Receiving the touch data is the same as for the
GENERIC_FT but the x and y cooridnates are swapped. The main differences
are the register addresses where the GAIN and THRESHOLD parameters are
stored.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwgIJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0F4H/jwv83AI9qxd4Zsj
geztCq0w1Vc48Gz/yDvl5MxZ74//q7Wz01qRTKisMNJla+Z0VuUReL12w0BGT0ko
ZwPqrvPtM04pA7A6J+vLM8t6k7Ck0q7xC3z/Y9eN5qxtC7yOX/X8RziiXBmyMzM5
nVpFYQwlk9/hSUHjPwMgf2dV32vNYl3FEph3g6nrqQLLdtsHiii9N8rC+cAU2jKg
sZ8Cp6REYYxt9LWEilsGof+oLnH+oUkXecB7WKKvSaAVHqR20xdpZ3ZvRcVyLfQ4
XCXBu8PIYYBWsa/iwuu0h4NuosGzEYbWOjnXKozOaV2KoqCT/Rk1egKIgb55EpyA
kFH4wfc=
=WAE7
-----END PGP SIGNATURE-----
Merge tag 'v4.20' into next
Merge with mainline to bring in the new APIs.
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
regmap_bulk_read() can return a non zero value on failure. The fix checks
if the function call succeeded before calling mod_timer. The issue was
identified by a static analysis tool.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A tiny pull request this merge window unfortunately, should get more
material in for the next release:
- new driver for Raspberry Pi's touchscreen (firmware interface)
- miscellaneous input driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G
Input: atmel_mxt_ts - don't try to free unallocated kernel memory
Input: drv2667 - fix indentation issues
Input: touchscreen - fix coding style issue
Input: add official Raspberry Pi's touchscreen driver
Input: nomadik-ske-keypad - fix a loop timeout test
Input: rotary-encoder - don't log EPROBE_DEFER to kernel log
Input: olpc_apsp - remove set but not used variable 'np'
Input: olpc_apsp - enable the SP clock
Input: olpc_apsp - check FIFO status on open(), not probe()
Input: olpc_apsp - drop CONFIG_OLPC dependency
clk: mmp2: add SP clock
dt-bindings: marvell,mmp2: Add clock id for the SP clock
Input: ad7879 - drop platform data support
