Reenable the 64-bit window during resume.
Fixes: fa564ad963 ("x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)")
Reported-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Avoid problems with BIOS implementations which don't report all used
resources to the OS by only allocating a 256GB window directly below the
hardware limit (from the BKDG, sec 2.4.6).
Fixes a silent reboot loop reported by Aaro Koskinen <aaro.koskinen@iki.fi>
on an AMD-based MSI MS-7699/760GA-P43(FX) system. This was apparently
caused by RAM or other unreported hardware that conflicted with the new
window.
Link: https://support.amd.com/TechDocs/49125_15h_Models_30h-3Fh_BKDG.pdf
Link: https://lkml.kernel.org/r/20180105220412.fzpwqe4zljdawr36@darkstar.musicnaut.iki.fi
Fixes: fa564ad963 ("x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: changelog, comment, Fixes:]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Only try to enable a 64-bit window on AMD CPUs when "pci=big_root_window"
is specified.
This taints the kernel because the new 64-bit window uses address space we
don't know anything about, and it may contain unreported devices or memory
that would conflict with the window.
The pci_amd_enable_64bit_bar() quirk that enables the window is specific to
AMD CPUs. The generic solution would be to have the firmware enable the
window and describe it in the host bridge's _CRS method, or at least
describe it in the _PRS method so the OS would have the option of enabling
it.
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: changelog, extend doc, mention taint in dmesg]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o3Rn
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.15-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- add a pci_get_domain_bus_and_slot() stub for the CONFIG_PCI=n case to
avoid build breakage in the v4.16 merge window if a
pci_get_bus_and_slot() -> pci_get_domain_bus_and_slot() patch gets
merged before the PCI tree (Randy Dunlap)
- fix an AMD boot regression in the 64bit BAR support added in v4.15
(Christian König)
- fix an R-Car use-after-free that causes a crash if no PCIe card is
present (Geert Uytterhoeven)
* tag 'pci-v4.15-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Fix use-after-free in probe error path
x86/PCI: Only enable a 64bit BAR on single-socket AMD Family 15h
x86/PCI: Fix infinite loop in search for 64bit BAR placement
PCI: Add pci_get_domain_bus_and_slot() stub
Pull misc x86 fixes from Ingo Molnar:
- make CR4 handling irq-safe, which bug vmware guests ran into
- don't crash on early IRQs in Xen guests
- don't crash secondary CPU bringup if #UD assisted WARN()ings are
triggered
- make X86_BUG_FXSAVE_LEAK optional on newer AMD CPUs that have the fix
- fix AMD Fam17h microcode loading
- fix broadcom_postcore_init() if ACPI is disabled
- fix resume regression in __restore_processor_context()
- fix Sparse warnings
- fix a GCC-8 warning
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Change time() prototype to match __vdso_time()
x86: Fix Sparse warnings about non-static functions
x86/power: Fix some ordering bugs in __restore_processor_context()
x86/PCI: Make broadcom_postcore_init() check acpi_disabled
x86/microcode/AMD: Add support for fam17h microcode loading
x86/cpufeatures: Make X86_BUG_FXSAVE_LEAK detectable in CPUID on AMD
x86/idt: Load idt early in start_secondary
x86/xen: Support early interrupts in xen pv guests
x86/tlb: Disable interrupts when changing CR4
x86/tlb: Refactor CR4 setting and shadow write
When we have a multi-socket system, each CPU core needs the same setup.
Since this is tricky to do in the fixup code, don't enable a 64bit BAR on
multi-socket systems for now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Break the loop if we can't find some address space for a 64bit BAR.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
acpi_os_get_root_pointer() may return a valid address even if acpi_disabled
is set, but the host bridge information from the ACPI tables is not going
to be used in that case and the Broadcom host bridge initialization should
not be skipped then, So make broadcom_postcore_init() check acpi_disabled
too to avoid this issue.
Fixes: 6361d72b04 (x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan)
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/3186627.pxZj1QbYNg@aspire.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* pci/resource:
PCI: Fail pci_map_rom() if the option ROM is invalid
PCI: Move pci_map_rom() error path
x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)
PCI: Add pci_resize_resource() for resizing BARs
PCI: Add resizable BAR infrastructure
PCI: Add PCI resource type mask #define
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Manually enable a 64GB 64-bit BAR so we have enough room for graphics
devices with large framebuffers.
Most BIOSes don't enable this for compatibility reasons.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Make this const as it is only used during a copy operation. This usage is
inside init function and the structure is not referenced after
initialisation, so make it __initconst too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZsr8cAAoJEFmIoMA60/r8lXYQAKViYIRMJDD4n3NhjMeLOsnJ
vwaBmWlLRjSFIEpag5kMjS1RJE17qAvmkBZnDvSNZ6cT28INkkZnVM2IW96WECVq
64MIvDijVPcvqGuWePCfWdDiSXApiDWwJuw55BOhmvV996wGy0gYgzpPY+1g0Knh
XzH9IOzDL79hZleLfsxX0MLV6FGBVtOsr0jvQ04k4IgEMIxEDTlbw85rnrvzQUtc
0Vj2koaxWIESZsq7G/wiZb2n6ekaFdXO/VlVvvhmTSDLCBaJ63Hb/gfOhwMuVkS6
B3cVprNrCT0dSzWmU4ZXf+wpOyDpBexlemW/OR/6CQUkC6AUS6kQ5si1X44dbGmJ
nBPh414tdlm/6V4h/A3UFPOajSGa/ZWZ/uQZPfvKs1R6WfjUerWVBfUpAzPbgjam
c/mhJ19HYT1J7vFBfhekBMeY2Px3JgSJ9rNsrFl48ynAALaX5GEwdpo4aqBfscKz
4/f9fU4ysumopvCEuKD2SsJvsPKd5gMQGGtvAhXM1TxvAoQ5V4cc99qEetAPXXPf
h2EqWm4ph7YP4a+n/OZBjzluHCmZJn1CntH5+//6wpUk6HnmzsftGELuO9n12cLE
GGkreI3T9ctV1eOkzVVa0l0QTE1X/VLyEyKCtb9obXsDaG4Ud7uKQoZgB19DwyTJ
EG76ridTolUFVV+wzJD9
=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
Use the is_vmd() predicate to identify devices below a VMD host rather than
relying on the domain number.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
VMD currently only exists for Intel x86 products, so move the VMD quirk to
arch/x86.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In the future we would use dynamic allocation for IRQ which brings
non-1:1 mapping for IOAPIC domain. Thus, we need to respect return value
of mp_map_gsi_to_irq() and assign it back to the device structure.
Besides that we need to read GSI from interrupt pin register to avoid
cases when some drivers will try to initialize PCI device twice in a row
which will call pcibios_enable_irq() twice as well.
serial 0000:00:04.1: Mapped GSI28 to IRQ5
serial 0000:00:04.2: Mapped GSI29 to IRQ5
serial 0000:00:04.3: Mapped GSI54 to IRQ5
8250_mid 0000:00:04.1: Mapped GSI28 to IRQ5
8250_mid 0000:00:04.2: Mapped GSI29 to IRQ6
8250_mid 0000:00:04.3: Mapped GSI54 to IRQ7
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20170724173402.12939-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ioremap() function is intended for mapping MMIO. For RAM, the
memremap() function should be used. Convert calls from ioremap() to
memremap() when re-mapping RAM.
This will be used later by SME to control how the encryption mask is
applied to memory mappings, with certain memory locations being mapped
decrypted vs encrypted.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Toshimitsu Kani <toshi.kani@hpe.com>
Cc: kasan-dev@googlegroups.com
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-efi@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/b13fccb9abbd547a7eef7b1fdfc223431b211c88.1500319216.git.thomas.lendacky@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls
to ->mapping_error so that the dma_map_ops instances are
more self contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)
-----BEGIN PGP SIGNATURE-----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=0Fso
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping infrastructure from Christoph Hellwig:
"This is the first pull request for the new dma-mapping subsystem
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls to
->mapping_error so that the dma_map_ops instances are more self
contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)"
* tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping: (56 commits)
ARM: dma-mapping: Remove traces of NOMMU code
ARM: NOMMU: Set ARM_DMA_MEM_BUFFERABLE for M-class cpus
ARM: NOMMU: Introduce dma operations for noMMU
drivers: dma-mapping: allow dma_common_mmap() for NOMMU
drivers: dma-coherent: Introduce default DMA pool
drivers: dma-coherent: Account dma_pfn_offset when used with device tree
dma: Take into account dma_pfn_offset
dma-mapping: replace dmam_alloc_noncoherent with dmam_alloc_attrs
dma-mapping: remove dmam_free_noncoherent
crypto: qat - avoid an uninitialized variable warning
au1100fb: remove a bogus dma_free_nonconsistent call
MAINTAINERS: add entry for dma mapping helpers
powerpc: merge __dma_set_mask into dma_set_mask
dma-mapping: remove the set_dma_mask method
powerpc/cell: use the dma_supported method for ops switching
powerpc/cell: clean up fixed mapping dma_ops initialization
tile: remove dma_supported and mapping_error methods
xen-swiotlb: remove xen_swiotlb_set_dma_mask
arm: implement ->dma_supported instead of ->set_dma_mask
mips/loongson64: implement ->dma_supported instead of ->set_dma_mask
...
* pci/resource:
PCI: Work around poweroff & suspend-to-RAM issue on Macbook Pro 11
PCI: Do not disregard parent resources starting at 0x0
Conflicts:
arch/x86/pci/fixup.c
* pci/pm:
PCI/PM: Avoid using device_may_wakeup() for runtime PM
x86/PCI: Avoid AMD SB7xx EHCI USB wakeup defect
PCI/PM: Restore the status of PCI devices across hibernation
drm/radeon: make MacBook Pro d3_delay quirk more generic
drm/amdgpu: remove unnecessary save/restore of pdev->d3_delay
PCI/PM: Add needs_resume flag to avoid suspend complete optimization
PCI: imx6: Fix config read timeout handling
switchtec: Fix minor bug with partition ID register
switchtec: Use new cdev_device_add() helper function
PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA
On an AMD Carrizo laptop, when EHCI runtime PM is enabled, EHCI ports do
not assert PME# for device plug/unplug events while in D3.
As Alan Stern points out [1], the PME signal is not enabled when controller
is in D3, therefore it's not being woken up when new devices get plugged
in.
Testing shows PME signal works when the EHCI power state is D2.
Clear the PCI_PM_CAP_PME_D3 and PCI_PM_CAP_PME_D3cold bits in
dev->pme_support to indicate the device will not assert PME# from those
states.
[1] http://lkml.kernel.org/r/Pine.LNX.4.44L0.1706121010010.2092-100000@iolanthe.rowland.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196091
Link: https://support.amd.com/TechDocs/46837.pdf (Section 23)
Link: https://support.amd.com/TechDocs/42413.pdf (Appendix A2)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
[bhelgaas: changelog, add parens in quirk]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Neither soft poweroff (transition to ACPI power state S5) nor
suspend-to-RAM (transition to state S3) works on the Macbook Pro 11,4 and
11,5.
The problem is related to the [mem 0x7fa00000-0x7fbfffff] space. When we
use that space, e.g., by assigning it to the 00:1c.0 Root Port, the ACPI
Power Management 1 Control Register (PM1_CNT) at [io 0x1804] doesn't work
anymore.
Linux does a soft poweroff (transition to S5) by writing to PM1_CNT. The
theory about why this doesn't work is:
- The write to PM1_CNT causes an SMI
- The BIOS SMI handler depends on something in
[mem 0x7fa00000-0x7fbfffff]
- When Linux assigns [mem 0x7fa00000-0x7fbfffff] to the 00:1c.0 Port, it
covers up whatever the SMI handler uses, so the SMI handler no longer
works correctly
Reserve the [mem 0x7fa00000-0x7fbfffff] space so we don't assign it to
anything.
This is voodoo programming, since we don't know what the real conflict is,
but we've failed to find the root cause.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=103211
Tested-by: thejoe@gmail.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Chen Yu <yu.c.chen@intel.com>
All x86 PCI configuration space accessors have either their own
serialization or can operate completely lockless (ECAM).
Disable the global lock in the generic PCI configuration space accessors.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <helgaas@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20170316215057.295079391@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86 wants to get rid of the global pci_lock protecting the config space
accessors so ECAM mode can operate completely lockless, but the CE4100 PCI
code relies on that to protect the simulation registers.
Restructure the code so it uses the x86 specific pci_config_lock to
serialize the inner workings of the CE4100 PCI magic. That allows to remove
the global locking via pci_lock later.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <helgaas@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20170316215057.126873574@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If the legacy PCI init fails, then there are no PCI config space accesors
available, but the code continues and tries to scan the busses, which fails
due to the lack of config space accessors.
Return right away, if the last init fallback fails.
Switch the few printks to pr_info while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <helgaas@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20170316215057.047576516@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
And instead wire it up as method for all the dma_map_ops instances.
Note that this also means the arch specific check will be fully instead
of partially applied in the AMD iommu driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
No need for such convoluted code, when all we need is to call one function
in one specific case.
Tested-by: Narendra K <Narendra.K@dell.com> # DellEMC PowerEdge 1950, R730XD
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the space from "PCI :" to make the message consistent with other PCI
messages.
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
set_memory_* functions have moved to set_memory.h. Switch to this
explicitly.
Link: http://lkml.kernel.org/r/1488920133-27229-6-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent discussion (http://marc.info/?l=xen-devel&m=149192184523741)
established that commit 72a9b18629 ("xen: Remove event channel
notification through Xen PCI platform device") (and thus commit
da72ff5bfc ("partially revert "xen: Remove event channel
notification through Xen PCI platform device"")) are unnecessary and,
in fact, prevent HVM guests from booting on Xen releases prior to 4.0
Therefore we revert both of those commits.
The summary of that discussion is below:
Here is the brief summary of the current situation:
Before the offending commit (72a9b18629):
1) INTx does not work because of the reset_watches path.
2) The reset_watches path is only taken if you have Xen > 4.0
3) The Linux Kernel by default will use vector inject if the hypervisor
support. So even INTx does not work no body running the kernel with
Xen > 4.0 would notice. Unless he explicitly disabled this feature
either in the kernel or in Xen (and this can only be disabled by
modifying the code, not user-supported way to do it).
After the offending commit (+ partial revert):
1) INTx is no longer support for HVM (only for PV guests).
2) Any HVM guest The kernel will not boot on Xen < 4.0 which does
not have vector injection support. Since the only other mode
supported is INTx which.
So based on this summary, I think before commit (72a9b18629) we were
in much better position from a user point of view.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Pull x86 boot updates from Ingo Molnar:
"The biggest changes in this cycle were:
- reworking of the e820 code: separate in-kernel and boot-ABI data
structures and apply a whole range of cleanups to the kernel side.
No change in functionality.
- enable KASLR by default: it's used by all major distros and it's
out of the experimental stage as well.
- ... misc fixes and cleanups"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
x86/KASLR: Fix kexec kernel boot crash when KASLR randomization fails
x86/reboot: Turn off KVM when halting a CPU
x86/boot: Fix BSS corruption/overwrite bug in early x86 kernel startup
x86: Enable KASLR by default
boot/param: Move next_arg() function to lib/cmdline.c for later reuse
x86/boot: Fix Sparse warning by including required header file
x86/boot/64: Rename start_cpu()
x86/xen: Update e820 table handling to the new core x86 E820 code
x86/boot: Fix pr_debug() API braindamage
xen, x86/headers: Add <linux/device.h> dependency to <asm/xen/page.h>
x86/boot/e820: Simplify e820__update_table()
x86/boot/e820: Separate the E820 ABI structures from the in-kernel structures
x86/boot/e820: Fix and clean up e820_type switch() statements
x86/boot/e820: Rename the remaining E820 APIs to the e820__*() prefix
x86/boot/e820: Remove unnecessary #include's
x86/boot/e820: Rename e820_mark_nosave_regions() to e820__register_nosave_regions()
x86/boot/e820: Rename e820_reserve_resources*() to e820__reserve_resources*()
x86/boot/e820: Use bool in query APIs
x86/boot/e820: Document e820__reserve_setup_data()
x86/boot/e820: Clean up __e820__update_table() et al
...
In all cases we know which BAR it is. Passing it in means that arch code
(or generic code; watch this space) won't have to go looking for it again.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYwPOdAAoJELDendYovxMvaREH/jWjZt38HQFyWYmpGN/jTl5e
fl2kK8PcYR50WDVMROG50MoWeDWj4OiCHkQTln/BIckBfi895qNE+S27Z6ZvPBcY
Xqx+lbcKej1KU5O11Kmmuz7Jz/h3pyP09lY7vG50pxLMBVJy8L2P3Oj66fB4MbY0
u5DQtPSwRDlf86gNisQuRHDYIF+LZ+ZQD5SL0hRz5UStnxojbX0oxP/ijz/tyshP
Qk5PZXWLOTcWn8mvKJu9wqfNur9FLT+FE8dYzAqa8hoLECl3wR3jUxGb1kNVt+GB
GuK6AHtJ7plVjfMYaAJtjYJnBaCGTCt3GuSzGJhoES0RkC/u1knuQBe87hKhzCc=
=gYGK
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.11-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix and cleanup from Juergen Gross:
"This contains one fix for MSIX handling under Xen and a trivial
cleanup patch"
* tag 'for-linus-4.11-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xenbus: Remove duplicate inclusion of linux/init.h
xen: do not re-use pirq number cached in pci device msi msg data
The revert of 991de2e590 ("PCI, x86: Implement pcibios_alloc_irq()
and pcibios_free_irq()") causes a problem for IOAPIC hotplug. The
problem is that IRQs are allocated and freed in pci_enable_device()
and pci_disable_device(). But there are some drivers which don't call
pci_disable_device(), and they have good reasons not calling it, so
if they're using IOAPIC their IRQs won't have a chance to be released
from the IOAPIC. When this happens IOAPIC hot-removal fails with a
kernel stack dump and an error message like this:
[149335.697989] pin16 on IOAPIC2 is still in use.
It turns out that we can fix it in a different way without moving IRQ
allocation into pcibios_alloc_irq(), thus avoiding the regression of
991de2e590. We can keep the allocation and freeing of IRQs as is
within pci_enable_device()/pci_disable_device(), without breaking any
previous assumption of the rest of the system, keeping compatibility
with both the legacy and the modern drivers. We can accomplish this by
implementing the existing __weak hook of pcibios_release_device() thus
when a pci device is about to be deleted we get notified in the hook
and take the chance to release its IRQ, if any, from the IOAPIC.
Implement pcibios_release_device() for x86 to release any IRQ not released
by the driver.
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Cc: tony.luck@intel.com
Cc: linux-pci@vger.kernel.org
Cc: rjw@rjwysocki.net
Cc: linux-acpi@vger.kernel.org
Cc: fengguang.wu@intel.com
Cc: helgaas@kernel.org
Cc: kbuild-all@01.org
Cc: bhelgaas@google.com
Link: http://lkml.kernel.org/r/1488288869-31290-2-git-send-email-rui.y.wang@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
Revert the main part of commit:
af42b8d12f ("xen: fix MSI setup and teardown for PV on HVM guests")
That commit introduced reading the pci device's msi message data to see
if a pirq was previously configured for the device's msi/msix, and re-use
that pirq. At the time, that was the correct behavior. However, a
later change to Qemu caused it to call into the Xen hypervisor to unmap
all pirqs for a pci device, when the pci device disables its MSI/MSIX
vectors; specifically the Qemu commit:
c976437c7dba9c7444fb41df45468968aaa326ad
("qemu-xen: free all the pirqs for msi/msix when driver unload")
Once Qemu added this pirq unmapping, it was no longer correct for the
kernel to re-use the pirq number cached in the pci device msi message
data. All Qemu releases since 2.1.0 contain the patch that unmaps the
pirqs when the pci device disables its MSI/MSIX vectors.
This bug is causing failures to initialize multiple NVMe controllers
under Xen, because the NVMe driver sets up a single MSIX vector for
each controller (concurrently), and then after using that to talk to
the controller for some configuration data, it disables the single MSIX
vector and re-configures all the MSIX vectors it needs. So the MSIX
setup code tries to re-use the cached pirq from the first vector
for each controller, but the hypervisor has already given away that
pirq to another controller, and its initialization fails.
This is discussed in more detail at:
https://lists.xen.org/archives/html/xen-devel/2017-01/msg00447.html
Fixes: af42b8d12f ("xen: fix MSI setup and teardown for PV on HVM guests")
Signed-off-by: Dan Streetman <dan.streetman@canonical.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Also do some minor cleanups.
No change in functionality.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Change e820__mapped_any() and e820__mapped_all()'s return type and
e820__range_remove()'s check_type parameter to bool.
Propagate it into arch/x86/pci/mmconfig-shared.c as this change
affects a function signature there too.
No change in functionality.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
So there's a number of constants that start with "E820" but which
are not types - these create a confusing mixture when seen together
with 'enum e820_type' values:
E820MAP
E820NR
E820_X_MAX
E820MAX
To better differentiate the 'enum e820_type' values prefix them
with E820_TYPE_.
No change in functionality.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The 'any' and 'all' are modified to the 'mapped' concept, so move them last in the name.
No change in functionality.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A commonly used lowlevel x86 header, asm/pgtable.h, includes asm/e820/api.h
spuriously, without making direct use of it.
Removing it is not simple: over the years various .c code learned to rely
on this indirect inclusion.
Remove the unnecessary include - this should speed up the kernel build a bit,
as a large header is not included anymore in totally unrelated code.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In line with asm/e820/types.h, move the e820 API declarations to
asm/e820/api.h and update all usage sites.
This is just a mechanical, obviously correct move & replace patch,
there will be subsequent changes to clean up the code and to make
better use of the new header organization.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some but not all architectures provide set_dma_ops(). Move dma_ops
from struct dev_archdata into struct device such that it becomes
possible on all architectures to configure dma_ops per device.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: x86@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
