The Amlogic SoC embeds a standalone CEC controller, this patch adds a driver
for such controller.
The controller does not need HPD to be active, and could support up to max
5 logical addresses, but only 1 is handled since the Suspend firmware can
make use of this unique logical address to wake up the device.
The Suspend firmware configuration will be added in an other patchset.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com:s/if (ret)/if (res)/ to fix obvious typo]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds Venus driver Makefile and changes v4l2 platform
Makefile/Kconfig in order to enable building of the driver.
Note that in this initial version the COMPILE_TEST-ing is not
supported because the drivers specific to ARM builds are still
in process of enabling the aforementioned compile testing.
Once that disadvantage is fixed the Venus driver compile testing
will be possible with follow-up changes.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver can handle SoC internal and external video bus multiplexers,
controlled by mux controllers provided by the mux controller framework,
such as MMIO register bitfields or GPIOs. The subdevice passes through
the mbus configuration of the active input to the output side.
Since the mux framework is not yet merged, this driver contains
temporary mmio-mux support to work without the framework. The driver
should be converted to use the multiplexer API once the "mux: minimal
mux subsystem" and "mux: mmio-based syscon mux controller" patches are
merged.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[hans.verkuil@cisco.com: add 'select REGMAP' to Kconfig]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds Digital Radio Interface (DRIF) support to R-Car Gen3 SoCs.
The driver exposes each instance of DRIF as a V4L2 SDR device. A DRIF
device represents a channel and each channel can have one or two
sub-channels respectively depending on the target board.
DRIF supports only Rx functionality. It receives samples from a RF
frontend tuner chip it is interfaced with. The combination of DRIF and the
tuner device, which is registered as a sub-device, determines the receive
sample rate and format.
In order to be compliant as a V4L2 SDR device, DRIF needs to bind with
the tuner device, which can be provided by a third party vendor. DRIF acts
as a slave device and the tuner device acts as a master transmitting the
samples. The driver allows asynchronous binding of a tuner device that
is registered as a v4l2 sub-device. The driver can learn about the tuner
it is interfaced with based on port endpoint properties of the device in
device tree. The V4L2 SDR device inherits the controls exposed by the
tuner device.
The device can also be configured to use either one or both of the data
pins at runtime based on the master (tuner) configuration.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch add cec driver for STM32 platforms.
cec hardware block isn't not always used with hdmi so
cec notifier is not implemented. That will be done later
when STM32 DSI driver will be available.
Driver compliance has been tested with cec-ctl and cec-compliance
tools.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
[hans.verkuil@cisco.com: modified platform/Makefile to use obj-y]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Depending on arch configs to include dirs is evil, and makes
harder to change drivers to work with COMPILE_TEST.
Replace them by obj-y.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
First version of the Virtual Media Controller.
Add a simple version of the core of the driver, the capture and
sensor nodes in the topology, generating a grey image in a hardcoded
format.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix small typo in Kconfig]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Update the bindings documenting the new hdmi phandle and
update exynos4.dtsi accordingly.
Tested with my Odroid U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
CC: linux-samsung-soc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move this out of the soc_camera directory into the atmel directory
where it belongs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FDP1 driver performs advanced de-interlacing on a memory 2 memory
based video stream, and supports conversion from YCbCr/YUV
to RGB pixel formats
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Linking soc_mediabus into this driver causes multiple definition linker warnings
if soc_camera is also enabled:
drivers/media/platform/soc_camera/built-in.o:(___ksymtab+soc_mbus_image_size+0x0): multiple definition of `__ksymtab_soc_mbus_image_size'
drivers/media/platform/soc_camera/soc_mediabus.o:(___ksymtab+soc_mbus_image_size+0x0): first defined here
>> drivers/media/platform/soc_camera/built-in.o:(___ksymtab+soc_mbus_samples_per_pixel+0x0): multiple definition of `__ksymtab_soc_mbus_samples_per_pixel'
drivers/media/platform/soc_camera/soc_mediabus.o:(___ksymtab+soc_mbus_samples_per_pixel+0x0): first defined here
drivers/media/platform/soc_camera/built-in.o: In function `soc_mbus_config_compatible':
(.text+0x3840): multiple definition of `soc_mbus_config_compatible'
drivers/media/platform/soc_camera/soc_mediabus.o:(.text+0x134): first defined here
Since we really don't want to have to use any of the soc-camera code this patch
copies the relevant code and data structures from soc_mediabus and renames it to pxa_mbus_*.
The large table of formats has been culled a bit, removing formats that are not supported
by this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As the conversion to a v4l2 standalone device is finished, move
pxa_camera one directory up and finish severing any dependency to
soc_camera.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds V4L2 HVA (Hardware Video Accelerator) video encoder
driver for STMicroelectronics SoC. It uses the V4L2 mem2mem framework.
This patch only contains the core parts of the driver:
- the V4L2 interface with the userland (hva-v4l2.c)
- the hardware services (hva-hw.c)
- the memory management utilities (hva-mem.c)
This patch doesn't include the support of specific codec (e.g. H.264)
video encoding: this support is part of subsequent patches.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The s5p-tv driver has been replaced by the exynos drm driver for quite a
long time now. Remove this driver to avoid having duplicate drivers,
of which this one is considered dead code by Samsung.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add driver for the Image Sensor Controller. It manages
incoming data from a parallel based CMOS/CCD sensor.
It has an internal image processor, also integrates a
triple channel direct memory access controller master
interface.
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* topic/vsp1: (36 commits)
[media] v4l: vsp1: wpf: Add flipping support
[media] v4l: vsp1: rwpf: Support runtime modification of controls
[media] v4l: vsp1: Simplify alpha propagation
[media] v4l: vsp1: clu: Support runtime modification of controls
[media] v4l: vsp1: lut: Support runtime modification of controls
[media] v4l: vsp1: Support runtime modification of controls
[media] v4l: vsp1: Add Cubic Look Up Table (CLU) support
[media] v4l: vsp1: lut: Expose configuration through a control
[media] v4l: vsp1: lut: Initialize the mutex
[media] v4l: vsp1: dl: Don't free fragments with interrupts disabled
[media] v4l: vsp1: Set entities functions
[media] v4l: vsp1: Don't create LIF entity when the userspace API is enabled
[media] v4l: vsp1: Don't register media device when userspace API is disabled
[media] v4l: vsp1: Base link creation on availability of entities
[media] media: Add video statistics computation functions
[media] media: Add video processing entity functions
[media] v4l: vsp1: sru: Fix intensity control ID
[media] v4l: vsp1: Stop the pipeline upon the first STREAMOFF
[media] v4l: vsp1: Constify operation structures
[media] v4l: vsp1: pipe: Fix typo in comment
...
The VPU driver for hw video codec embedded in Mediatek's MT8173 SOCs.
It is able to handle video decoding/encoding of in a range of formats.
The driver provides with VPU firmware download, memory management and
the communication interface between CPU and VPU.
For VPU initialization, it will create virtual memory for CPU access and
IOMMU address for vcodec hw device access. When a decode/encode instance
opens a device node, vpu driver will download vpu firmware to the device.
A decode/encode instant will decode/encode a frame using VPU
interface to interrupt vpu to handle decoding/encoding jobs.
Signed-off-by: Andrew-CT Chen <andrew-ct.chen@mediatek.com>
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
[hans.verkuil@cisco.com: drop unnecessary ARM || ARM64 dependency]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FCP is a companion module of video processing modules in the
Renesas R-Car Gen3 SoCs. It provides data compression and decompression,
data caching, and conversion of AXI transactions in order to reduce the
memory bandwidth.
The driver is not meant to be used standalone but provides an API to the
video processing modules to control the FCP.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A V4L2 driver for Renesas R-Car VIN driver that do not depend on
soc_camera. The driver is heavily based on its predecessor and aims to
replace it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Timberdale FPGA video driver has not seen any real development
since 2011 (and very little before that).
One of the problems with the timblogiw driver is that it uses videobuf
instead of the newer vb2 framework. The long term goal is to either
convert or remove any driver still using videobuf. Since none of the
core v4l developers has the hardware, we cannot convert it ourselves.
As far as I can tell it was only used in an Intel demo board in 2009
using Meego:
http://www.chinait.com/intelcontent/intelprc/admin/PDFFile/20106411545.pdf
which has since been superseded.
Moving this driver to staging is the first step towards removal. After 2 or
3 kernel cycles it will be removed altogether unless someone steps up to
clean up this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Richard Röjfors <richard@puffinpack.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Camera Adaptation Layer (CAL) is a block which consists of a dual
port CSI2/MIPI camera capture engine.
Port #0 can handle CSI2 camera connected to up to 4 data lanes.
Port #1 can handle CSI2 camera connected to up to 2 data lanes.
The driver implements the required API/ioctls to be V4L2 compliant.
Driver supports the following:
- V4L2 API using DMABUF/MMAP buffer access based on videobuf2 api
- Asynchronous sensor sub device registration
- DT support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the Kconfig and Makefile for the c8sectpfe driver
so it will be built. It also selects additional demodulator and tuners
which are required by the supported NIM cards.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Here's the driver for the Renesas R-Car JPEG processing unit.
The driver is implemented within the V4L2 framework as a memory-to-memory
device. It presents two video nodes to userspace, one for the encoding part,
and one for the decoding part.
It was found that the only working mode for encoding is no markers output, so we
generate markers with software. In the current version of driver we also use
software JPEG header parsing because with hardware parsing performance is lower
than desired.
>From a userspace point of view the process is typical (S_FMT, REQBUF,
optionally QUERYBUF, QBUF, STREAMON, DQBUF) for both the source and destination
queues. STREAMON can return -EINVAL in case of mismatch of output and capture
queues format. Also during decoding driver can return buffers if queued
buffer with JPEG image contains image with inappropriate subsampling (e.g.
4:2:0 in JPEG and 4:2:2 in capture). If JPEG image and queue format dimensions
differ driver will return buffer on QBUF with VB2_BUF_STATE_ERROR flag.
During encoding the available formats are: V4L2_PIX_FMT_NV12M,
V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16, V4L2_PIX_FMT_NV16M for source and
V4L2_PIX_FMT_JPEG for destination.
During decoding the available formats are: V4L2_PIX_FMT_JPEG for source and
V4L2_PIX_FMT_NV12M, V4L2_PIX_FMT_NV16M, V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16
for destination.
Performance of current version:
1280x800 NV12 image encoding/decoding
decoding ~122 FPS
encoding ~191 FPS
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This v4l2 mem2mem driver is a 2D blitter for STMicroelectronics SoC.
It uses the v4l2 mem2mem framework.
The following features are supported and tested:
- Color format conversion (RGB32, RGB24, RGB16, NV12, YUV420P)
- Copy
- Scale
- Flip
- Deinterlace
- Wide (4K) picture support
- Crop
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: added missing slab.h include to bdisp-v4l2.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Xilinx platforms have no hardwired video capture or video processing
interface. Users create capture and memory to memory processing
pipelines in the FPGA fabric to suit their particular needs, by
instantiating video IP cores from a large library.
The Xilinx Video IP core is a framework that models a video pipeline
described in the device tree and expose the pipeline to userspace
through the media controller and V4L2 APIs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds Video Processing Front End (VPFE) driver for
AM437X family of devices
Driver supports the following:
- V4L2 API using MMAP buffer access based on videobuf2 api
- Asynchronous sensor/decoder sub device registration
- DT support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[hans.verkuil@cisco.com: swapped two lines to fix vpfe_release() & add pinctrl include]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible.
So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is 1) *much* easier to type, and 2) is consistent with vivid
('vi' for virtual). More of such virtual drivers are planned, so keeping
the naming consistent makes sense.
Note that the old module name is retained as a module alias.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch removes unneeded dependency of ARCH_OMAP3
on VIDEO_DM6446_CCDC.
Also the top level platform Makefile descended into
davinci/ without any dependency so just drop the
dependency obj-y, as obj-$(CONFIG_ARCH_DAVINCI)
already exists.
Reported-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vivid driver is a vastly superior test driver, so just drop the old
vivi driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Update the Kconfig and Makefile files so this driver can be compiled.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The coda driver has grown significantly and will continue to grow.
Move the coda driver into its own directory so it can be split.
Rename coda.h to coda_regs.h as it contains the register defines.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.
Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.
This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.
If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:
<URL:http://vihersipuli.retiisi.org.uk/cgi-bin/gitweb.cgi?p=~sailus/linux-omap/.git;a=summary>
The branch is n800-cam. Porting to up-to-date APIs can then be done. David
might have done some work in that area, so check with him first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: David Cohen <dacohen@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE is a block which consists of a single memory to memory path which
can perform chrominance up/down sampling, de-interlacing, scaling, and
color space conversion of raster or tiled YUV420 coplanar, YUV422
coplanar or YUV422 interleaved video formats.
We create a mem2mem driver based primarily on the mem2mem-testdev
example. The de-interlacer, scaler and color space converter are all
bypassed for now to keep the driver simple. Chroma up/down sampler
blocks are implemented, so conversion beteen different YUV formats is
possible.
Each mem2mem context allocates a buffer for VPE MMR values which it will
use when it gets access to the VPE HW via the mem2mem queue, it also
allocates a VPDMA descriptor list to which configuration and data
descriptors are added.
Based on the information received via v4l2 ioctls for the source and
destination queues, the driver configures the values for the MMRs, and
stores them in the buffer. There are also some VPDMA parameters like
frame start and line mode which needs to be configured, these are
configured by direct register writes via the VPDMA helper functions.
The driver's device_run() mem2mem op will add each descriptor based on
how the source and destination queues are set up for the given ctx, once
the list is prepared, it's submitted to VPDMA, these descriptors when
parsed by VPDMA will upload MMR registers, start DMA of video buffers on
the various input and output clients/ports.
When the list is parsed completely(and the DMAs on all the output ports
done), an interrupt is generated which we use to notify that the source
and destination buffers are done. The rest of the driver is quite
similar to other mem2mem drivers, we use the multiplane v4l2 ioctls as
the HW support coplanar formats.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 is a video processing engine that includes a blender, scalers,
filters and statistics computation. Configurable data path routing logic
allows ordering the internal blocks in a flexible way.
Due to the configurable nature of the pipeline the driver implements the
media controller API and doesn't use the V4L2 mem-to-mem framework, even
though the device usually operates in memory to memory mode.
Only the read pixel formatters, up/down scalers, write pixel formatters
and LCDC interface are supported at this stage.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The s5p-fimc directory now contains drivers for multiple IP blocks
found in multiple Samsung application processors. This includes FIMC
(CAMIF), MIPI CSIS and FIMC LITE. FIMC-IS (Imaging Subsystem) driver
is going to be put into same directory. Hence we rename it to
exynos4-is as s5p-fimc was only relevant for early version of this
driver, when it only supported FIMC IP block.
The imaging subsystem drivers for Exynos4 SoC series and S5PV210 will
be included in drivers/media/platform/exynos4-is directory, with some
modules shared with exynos5 series, while the rest of exynos5 specific
modules will find their home in drivers/media/platform/exynos5-is.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video Engine Unit (VEU) is an IP block, found in multiple SuperH and ARM-
based sh-mobile and r-mobile SoCs, capable of processing video data. It
can perform colour-space conversion, scaling and several filtering
transformations. This patch adds an initial implementation of a mem2mem
V4L2 driver for VEU. So far only conversion from NV12 to RGB565 is
supported. Further functionality shall be added in the future.
This driver is based on a VEU vidix driver by Magnus Damm.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds V4L2 driver for Samsung S3C24XX/S3C64XX SoC series
camera interface. The driver exposes a subdev device node for CAMIF
pixel resolution and crop control and two video capture nodes - for
the "codec" and "preview" data paths. It has been tested on Mini2440
(s3c2440) and Mini6410 (s3c6410) board with gstreamer and mplayer.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Andrey Gusakov <dron0gus@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-EMISSINGMAKEFILE
Without a Makefile, the driver will not compile, causing
breakages for arm exynos5 sub-architecture.
Cc: Shaik Ameer Basha <shaik.ameer@samsung.com>
Cc: Sungchun Kang <sungchun.kang@samsung.com>
Cc: "Seung-Woo Kim/Mobile S/W Platform Lab(DMC)/E4" <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/built-in.o: In function `imx074_s_power':
imx074.c:(.text+0x1de93d0): undefined reference to `soc_camera_power_on'
imx074.c:(.text+0x1de93f3): undefined reference to `soc_camera_power_off'
drivers/built-in.o: In function `mt9m001_s_mbus_config':
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A trivial fix so that vino can find the saa7191.h header.
[mchehab@redhat.com: Fix merge conflict]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
