Make sure the queue structures exist before trying
to delete them. This addresses a couple of error
recovery issues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean out tx requests that didn't get finished before
shutting down the queue.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the irq request and free out of the qcq_init and deinit
and into the alloc and free routines where they belong for
better resource management.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the qcq debugfs add to the queue alloc, and likewise move
the debugfs delete to the queue free. The LIF debugfs add
also needs to be moved, but the del is already in the LIF free.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a link_status_check to the heartbeat watchdog.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange the link_up/link_down messages so that we announce
link up when we first notice that the link is up when the
driver loads, and decouple the link_up/link_down messages from
the UP and DOWN netdev state.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit extended the enums 'hwtstamp_tx_types' and
'hwtstamp_rx_filters' with values that were not accounted for in the
switch statements, resulting in the build warnings below.
Fix by adding a default case.
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c: In function ‘mlxsw_sp_ptp_get_message_types’:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:915:2: warning: enumeration value ‘__HWTSTAMP_TX_CNT’ not handled in switch [-Wswitch]
915 | switch (tx_type) {
| ^~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:927:2: warning: enumeration value ‘__HWTSTAMP_FILTER_CNT’ not handled in switch [-Wswitch]
927 | switch (rx_filter) {
| ^~~~~~
Fixes: f76510b458 ("ethtool: add timestamping related string sets")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=6Glq
-----END PGP SIGNATURE-----
Merge tag 'for-5.7/block-2020-03-29' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Online capacity resizing (Balbir)
- Number of hardware queue change fixes (Bart)
- null_blk fault injection addition (Bart)
- Cleanup of queue allocation, unifying the node/no-node API
(Christoph)
- Cleanup of genhd, moving code to where it makes sense (Christoph)
- Cleanup of the partition handling code (Christoph)
- disk stat fixes/improvements (Konstantin)
- BFQ improvements (Paolo)
- Various fixes and improvements
* tag 'for-5.7/block-2020-03-29' of git://git.kernel.dk/linux-block: (72 commits)
block: return NULL in blk_alloc_queue() on error
block: move bio_map_* to blk-map.c
Revert "blkdev: check for valid request queue before issuing flush"
block: simplify queue allocation
bcache: pass the make_request methods to blk_queue_make_request
null_blk: use blk_mq_init_queue_data
block: add a blk_mq_init_queue_data helper
block: move the ->devnode callback to struct block_device_operations
block: move the part_stat* helpers from genhd.h to a new header
block: move block layer internals out of include/linux/genhd.h
block: move guard_bio_eod to bio.c
block: unexport get_gendisk
block: unexport disk_map_sector_rcu
block: unexport disk_get_part
block: mark part_in_flight and part_in_flight_rw static
block: mark block_depr static
block: factor out requeue handling from dispatch code
block/diskstats: replace time_in_queue with sum of request times
block/diskstats: accumulate all per-cpu counters in one pass
block/diskstats: more accurate approximation of io_ticks for slow disks
...
Eran Ben Elisha says:
====================
Devlink health auto attributes refactor
This patchset refactors the auto-recover health reporter flag to be
explicitly set by the devlink core.
In addition, add another flag to control auto-dump attribute, also
to be explicitly set by the devlink core.
For that, patch 0001 changes the auto-recover default value of
netdevsim dummy reporter.
After reporter registration, both flags can be altered be administrator
only.
Changes since v1:
- Change default behaviour of netdevsim dummy reporter
- Move initialization of DEVLINK_ATTR_HEALTH_REPORTER_AUTO_DUMP
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On low memory system, run time dumps can consume too much memory. Add
administrator ability to disable auto dumps per reporter as part of the
error flow handle routine.
This attribute is not relevant while executing
DEVLINK_CMD_HEALTH_REPORTER_DUMP_GET.
By default, auto dump is activated for any reporter that has a dump method,
as part of the reporter registration to devlink.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When health reporter is registered to devlink, devlink will implicitly set
auto recover if and only if the reporter has a recover method. No reason
to explicitly get the auto recover flag from the driver.
Remove this flag from all drivers that called
devlink_health_reporter_create.
All existing health reporters set auto recovery to true if they have a
recover method.
Yet, administrator can unset auto recover via netlink command as prior to
this patch.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health reporters should be registered with auto recover set to true.
Align dummy reporter behaviour with that, as in later patch the option to
set auto recover behaviour will be removed.
In addition, align netdevsim selftest to the new default value.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP Hardware Clock (PHC) subsystem offers an API for configuring
programmable pins. User space sets or gets the settings using ioctls,
and drivers verify dialed settings via a callback. Drivers may also
query pin settings by calling the ptp_find_pin() method.
Although the core subsystem protects concurrent access to the pin
settings, the implementation places illogical restrictions on how
drivers may call ptp_find_pin(). When enabling an auxiliary function
via the .enable(on=1) callback, drivers may invoke the pin finding
method, but when disabling with .enable(on=0) drivers are not
permitted to do so. With the exception of the mv88e6xxx, all of the
PHC drivers do respect this restriction, but still the locking pattern
is both confusing and unnecessary.
This patch changes the locking implementation to allow PHC drivers to
freely call ptp_find_pin() from their .enable() and .verify()
callbacks.
V2 ChangeLog:
- fixed spelling in the kernel doc
- add Vladimir's tested by tag
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=vn2E
-----END PGP SIGNATURE-----
Merge tag 'for-5.7/libata-2020-03-29' of git://git.kernel.dk/linux-block
Pull libata updates from Jens Axboe:
- Series from Bart, making the libata code smaller on PATA only setups.
This is useful for smaller/embedded use cases, and will help us move
some of those off drivers/ide.
- Kill unused BPRINTK() (Hannes)
- Add various Comet Lake ahci PCI ids (Kai-Heng, Mika)
- Fix for a double scsi_host_put() in error handling (John)
- Use scnprintf (Takashi)
- Assign OF node to the SCSI device (Linus Walleij)
* tag 'for-5.7/libata-2020-03-29' of git://git.kernel.dk/linux-block: (36 commits)
ata: make "libata.force" kernel parameter optional
ata: move ata_eh_analyze_ncq_error() & co. to libata-sata.c
ata: start separating SATA specific code from libata-eh.c
ata: move ata_sas_*() to libata-sata.c
ata: start separating SATA specific code from libata-scsi.c
ata: move sata_deb_timing_*() to libata-sata.c
ata: move ata_qc_complete_multiple() to libata-sata.c
ata: move sata_link_hardreset() to libata-sata.c
ata: move sata_link_{debounce,resume}() to libata-sata.c
ata: move *sata_set_spd*() to libata-sata.c
ata: move sata_scr_*() to libata-sata.c
ata: start separating SATA specific code from libata-core.c
ata: let compiler optimize out ata_eh_set_lpm() on non-SATA hosts
ata: let compiler optimize out ata_dev_config_ncq() on non-SATA hosts
ata: add CONFIG_SATA_HOST=n version of ata_ncq_enabled()
ata: separate PATA timings code from libata-core.c
ata: fix CodingStyle issues in PATA timings code
ata: remove EXPORT_SYMBOL_GPL()s not used by modules
ata: move EXPORT_SYMBOL_GPL()s close to exported code
ata: optimize ata_scsi_rbuf[] size
...
The rest of the devlink code sets the extack message using
NL_SET_ERR_MSG_MOD. Change the existing appearances of NL_SET_ERR_MSG
to NL_SET_ERR_MSG_MOD.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
net: sched: expose HW stats types per action used by drivers
The first patch is just adding a helper used by the second patch too.
The second patch is exposing HW stats types that are used by drivers.
Example:
$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 10 sec used 10 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be up to the driver (in case ANY HW stats is passed) to select
which type of HW stats he is going to use. Add an infrastructure to
expose this information to user.
$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 10 sec used 10 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper to pass value and selector to. The helper packs them
into struct and puts them into netlink message.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Stop using the deprecated i2c_new_device() function
* Replace zero-length array with flexible-array member
-----BEGIN PGP SIGNATURE-----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=79Ge
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Boris Brezillon:
- Fix driver auto-probing related issues
- Stop using the deprecated i2c_new_device() function
- Replace zero-length array with flexible-array member
* tag 'i3c/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: convert to use i2c_new_client_device()
i3c: master: Replace zero-length array with flexible-array member
i3c: Simplify i3c_device_match_id()
i3c: Generate aliases for i3c modules
i3c: Add a modalias sysfs attribute
i3c: Fix MODALIAS uevents
i3c: master: no need to iterate master device twice
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-03-28
1) Use kmem_cache_zalloc() instead of kmem_cache_alloc()
in xfrm_state_alloc(). From Huang Zijiang.
2) esp_output_fill_trailer() is the same in IPv4 and IPv6,
so share this function to avoide code duplcation.
From Raed Salem.
3) Add offload support for esp beet mode.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: fixes for -net
This patchset includes some bugfixes for the HNS3 ethernet driver.
[patch 1] removes flag WQ_MEM_RECLAIM flag when allocating WE,
since it will cause a warning when the reset task flushes a IB's WQ.
[patch 2] adds a new DESC_TYPE_FRAGLIST_SKB type to handle the
linear data of the fraglist SKB, since it is different with the frag
data.
[patch 3] adds different handings for RSS configuration when load
or reset.
[patch 4] fixes a link ksetting issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is not open, the service task which update the port
information per second is not running. In this case, the port
capabilities, including speed ability, autoneg ability, media type,
may be incorrect. Then get/set link ksetting may fail.
This patch fixes it by updating the port information before getting/
setting link ksettings when device is not open, and start timer
task immediately by setting delay time to 0 when device opens.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VF's RSS configuration would be set to default
after VF reset, the the user's one will loss.
To fix it, this patch separates hclgevf_rss_init_hw() into
two parts, one sets up the default RSS configuration and
just be called when driver loading, one configures the hardware
and be called by driver loading or reset.
Fixes: d97b307213 ("net: hns3: Add RSS tuples support for VF")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the fraglist SKB headlen is larger than zero, current code
still handle the fraglist SKB linear data as frag data, which may
cause TX error.
This patch adds a new DESC_TYPE_FRAGLIST_SKB type to handle the
mapping and unmapping of the fraglist SKB linear data buffer.
Fixes: 8ae10cfb50 ("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iJYEABYIAD4WIQRE6pSOnaBC00OEHEIaerohdGur0gUCXm6wmiAcamFya2tvLnNh
a2tpbmVuQGxpbnV4LmludGVsLmNvbQAKCRAaerohdGur0txuAP9WLoapeGoI+jnq
5SowWPRdHaKEX3Ez7CTZJll03pAoOAEAjX99WhbVZZe4CK3QLYRryZQobm2myk+/
z192BJwtnA8=
=vd/3
-----END PGP SIGNATURE-----
Merge tag 'tpmdd-next-20200316' of git://git.infradead.org/users/jjs/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen:
"tpmdd updates for Linux v5.7"
* tag 'tpmdd-next-20200316' of git://git.infradead.org/users/jjs/linux-tpmdd:
KEYS: reaching the keys quotas correctly
tpm: ibmvtpm: Add support for TPM2
tpm: ibmvtpm: Wait for buffer to be set before proceeding
tpm: of: Handle IBM,vtpm20 case when getting log parameters
MAINTAINERS: adjust to trusted keys subsystem creation
tpm: tpm_tis_spi_cr50: use new structure for SPI transfer delays
tpm_tis_spi: use new 'delay' structure for SPI transfer delays
tpm: tpm2_bios_measurements_next should increase position index
tpm: tpm1_bios_measurements_next should increase position index
tpm: Don't make log failures fatal
There is no point in preparing the module name in a buffer. The format
string can be passed diectly to 'request_module()'.
This axes a few lines of code and cleans a few things:
- max len for a driver name is MODULE_NAME_LEN wich is ~ 60 chars,
not 128. It would be down-sized in 'request_module()'
- we should pass the total size of the buffer to 'snprintf()', not the
size minus 1
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/amazon/ena/ena_netdev.c:460:6: warning: symbol 'ena_xdp_exchange_program_rx_in_range' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:481:6: warning: symbol 'ena_xdp_exchange_program' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:1555:5: warning: symbol 'ena_xdp_handle_buff' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2065:5:
warning: symbol 'dpaa_a050385_wa' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possibility that cdev is removed before CPL_ABORT_REQ_RSS
is fully processed, so it's better to save it in skb.
Added checks in handling the flow correctly, which suggests connection reset
request is sent to HW, wait for HW to respond.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
On udp rx path udp_rcv_segment() may do segment where the frag skbs
will get the header copied from the head skb in skb_segment_list()
by calling __copy_skb_header(), which could overwrite the frag skbs'
extensions by __skb_ext_copy() and cause a leak.
This issue was found after loading esp_offload where a sec path ext
is set in the skb.
Fix this by discarding head state of the fraglist skb before replacing
its contents.
Fixes: 3a1296a38d ("net: Support GRO/GSO fraglist chaining.")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Reported-by: Xiumei Mu <xmu@redhat.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 header's payload length field shouldn't include IPv6 header length.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for VLAN ID-based filtering by the MAC controller for MAC
drivers that support it. Only the 12-bit VID field is used.
Signed-off-by: Chuah Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without NAPI_GRO_CB(skb)->is_flist initialized, when the dev doesn't
support NETIF_F_GRO_FRAGLIST, is_flist can still be set and fraglist
will be used in udp_gro_receive().
So fix it by initializing is_flist with 0 in udp_gro_receive.
Fixes: 9fd1ff5d2a ("udp: Support UDP fraglist GRO/GSO.")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ayush Sawal says:
====================
crypto: chelsio: Fixes issues during chcr driver registration
Patch 1: Avoid the accessing of wrong u_ctx pointer.
Patch 2: Fixes a deadlock between rtnl_lock and uld_mutex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The locks are taken in this order during driver registration
(uld_mutex), at: cxgb4_register_uld.part.14+0x49/0xd60 [cxgb4]
(rtnl_mutex), at: rtnetlink_rcv_msg+0x2db/0x400
(uld_mutex), at: cxgb_up+0x3a/0x7b0 [cxgb4]
(rtnl_mutex), at: chcr_add_xfrmops+0x83/0xa0 [chcr](stucked here)
To avoid this now the netdev features are updated after the
cxgb4_register_uld function is completed.
Fixes: 6dad4e8ab3 ("chcr: Add support for Inline IPSec").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue occurs only when multiadapters are present. Hang
happens because assign_chcr_device returns u_ctx pointer of
adapter which is not yet initialized as for this adapter cxgb_up
is not been called yet.
The last_dev pointer is used to determine u_ctx pointer and it
is initialized two times in chcr_uld_add in chcr_dev_add respectively.
The fix here is don't initialize the last_dev pointer during
chcr_uld_add. Only assign to value to it when the adapter's
initialization is completed i.e in chcr_dev_add.
Fixes: fef4912b66 ("crypto: chelsio - Handle PCI shutdown event").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'pm_nl_ctl' was adding a trailing whitespace after having printed the
IP. But at the end, the IP element is currently always the last one.
The bash script launching 'pm_nl_ctl' had trailing whitespaces in the
expected result on purpose. But these whitespaces have been removed when
the patch has been applied upstream. To avoid trailing whitespaces in
the bash code, 'pm_nl_ctl' and expected results have now been adapted.
The MPTCP PM selftest can now pass again.
Fixes: eedbc68532 (selftests: add PM netlink functional tests)
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) mlx5 core level updates for mkey APIs + migrate some code to mlx5_ib
2) Use a separate work queue for fib event handling
3) Move new eswitch chains files to a new directory, to prepare for
upcoming E-Switch and offloads features.
4) Support indr block setup (TC_SETUP_FT) in Flow Table mode.
--
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl6BlNUACgkQSD+KveBX
+j4LMAf/QszF52vJ0CmJQCuuaor2W1SGhluT183uU8Eac9GIq0XXHwD81O3FC01+
qk1NaVcULqt9eGwZq5WOQIF+pw1gcnlZlg/UCaQBWWkCmdTbrJIwRTou9VwYR+hi
i9QB3/WKhpm9c/u/7MI6YZkQmjTLNDxYyF6/dqT3TyrRxwDRejeRtsUDdQTwswBV
p2Jw3nyLbviAr2g7MAF/CvVtjsl7rDUuJkdWvgvCIgsJzLMtIuduuTf7Q3dsvKUe
GZNWhp+9lKJajdHbQaKjOK5XODoQAbRdPeMV6umV3lWmgRU7Bc4s8/jxChX5NnX9
yieLnsqwqw1aJbh35yMtuVRtVsp+HA==
=ZhTN
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-03-29
1) mlx5 core level updates for mkey APIs + migrate some code to mlx5_ib
2) Use a separate work queue for fib event handling
3) Move new eswitch chains files to a new directory, to prepare for
upcoming E-Switch and offloads features.
4) Support indr block setup (TC_SETUP_FT) in Flow Table mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ordinarily, function gfs2_ail1_start_one issues a write request
for one item on the ail1 list, then returns -EBUSY. This makes the
caller, gfs2_ail1_flush, loop around and start another. However,
it was not clearing the -EBUSY return code each time through the loop.
So on rare occasions, like when the wbc runs out of nr_to_write, it
remained set to -EBUSY, which triggered an error and withdraw.
This patch sets the return code to 0 each time through the restart
loop so this won't happen anymore.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
* acpi-ec:
ACPI: EC: Eliminate EC_FLAGS_QUERY_HANDSHAKE
ACPI: EC: Do not clear boot_ec_is_ecdt in acpi_ec_add()
ACPI: EC: Simplify acpi_ec_ecdt_start() and acpi_ec_init()
ACPI: EC: Consolidate event handler installation code
ACPI: EC: Use fast path in acpi_ec_add() for DSDT boot EC
ACPI: EC: Simplify acpi_ec_add()
ACPI: EC: Drop AE_NOT_FOUND special case from ec_install_handlers()
ACPI: EC: Avoid passing redundant argument to functions
ACPI: EC: Avoid printing confusing messages in acpi_ec_setup()
* acpi-fan:
ACPI: fan: Use scnprintf() for avoiding potential buffer overflow
* acpi-pci:
ACPI: PCI: Use scnprintf() for avoiding potential buffer overflow
* acpica:
ACPICA: Update version to 20200214
ACPICA: Fix a couple of typos
ACPICA: use acpi_size instead of u32 for prefix_path_length
ACPICA: cast length arguement to acpi_ns_build_normalized_path() as u32
ACPICA: cast the result of the pointer difference to u32
ACPICA: Table Manager: Update comments in a function header
ACPICA: Enable sleep button on ACPI legacy wake
ACPICA: Fix a comment "enable" fixed events -> "disable" all fixed events.
ACPICA: ASL-ASL+ converter: make root file a parameter for cv_init_file_tree
ACPICA: ASL-ASL+ converter: remove function parameters from cv_init_file_tree()
ACPICA commit ac0c1b8a43a317702bb11e11fd5067a1c59e3002
Version 20200214
Link: https://github.com/acpica/acpica/commit/ac0c1b8a
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Kaneda <erik.kaneda@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpuidle:
cpuidle: haltpoll: allow force loading on hosts without the REALTIME hint
intel_idle: Update copyright notice, known limitations and version
intel_idle: Define CPUIDLE_FLAG_TLB_FLUSHED as BIT(16)
intel_idle: Clean up kerneldoc comments for multiple functions
intel_idle: Reorder declarations of static variables
intel_idle: Annotate init time data structures
intel_idle: Add __initdata annotations to init time variables
intel_idle: Relocate definitions of cpuidle callbacks
intel_idle: Clean up definitions of cpuidle callbacks
intel_idle: Simplify LAPIC timer reliability checks
