Use a default antenna diversity value for AR9565 instead
of relying on the EEPROM/OTP programmed value.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This starves FW RX ring buffer in case of
excessive RX. This prevents from CPU being
overwhelmed by RX indications/completions by
naturally forbiddin FW to submit more RX.
This fixes RX starvation on slow machines when
under heavy RX traffic.
kvalo: remove extra newline
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ethernet-like decapping mode leaves IP protocol
frame not aligned to 4-byte boundaries. This leads
to re-aligning in mac80211 which in turn leads to
poor CPU cache behaviour on some machines.
Since HW doesn't allow to change payload offset
properly the solution is to force HW to decap in
Native Wifi mode which always has 24-bytes long
802.11 header (even for QoS frames). This means IP
frame is properly aligned in this decap mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
NWifi decap mode always reports 802.11 Data
Frames, even when QoS Data Frames are actually
received.
This made mac80211 not report frame priority
properly (since there was no QoS Control field).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simplify decapping code and make it easier to
understand.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Clarify how each decap mode works in one place.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW reports each A-MSDU subframe as a separate
sk_buff. It is impossible to configure it to
behave differently.
Until now ath10k was reconstructing A-MSDUs from
subframes which involved a lot of memory
operations. This proved to be a significant
contributor to degraded RX performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of allocating sk_buff for a mere 16-byte
tx fragment list buffer use headroom of the
original msdu sk_buff.
This decreases CPU cache pressure and improves
performance.
Measured improvement on AP135 is 560mbps ->
590mbps of UDP TX briding traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use a saner goto scheme for failure handling. Also
group operations more sensibly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now the all MSDU transfer related structures
were freed when all resources were unreferenced.
Now HTC transfer is freed independently and HTT
transfer is so too.
This yields a way more simpler ath10k_skb_cb and
should possibly enable parallel pipe processing
(which is now serialized in
ath10k_pci_process_ce routine).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reduces number of memory accesses and
hopefully contributes to better performance in the
future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's more efficient to simply check num_pending_tx
value instead of traversing whole bitmap of
msdu ids.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit e9bb0aa39 ("ath10k: delete struct ce_sendlist") broke
num_sends_allowed incrementing. num_sends_allowed
exceeded initial values and could overflow.
This code was supposed to replenish
num_sends_allowed for partial sendlist items (i.e.
before final sendlist item from a sendlist was
completed and could be processed by completion
handlers).
Fortunately it seems it did not cause any major breakage,
yet.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit be8b394390 ("ath10k: make WMI commands block by design") broke
the build if CONFIG_ATH10K_TRACING was enabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking fixes from David Miller:
1) If the local_df boolean is set on an SKB we have to allocate a
unique ID even if IP_DF is set in the ipv4 headers, from Ansis
Atteka.
2) Some fixups for the new chipset support that went into the sfc
driver, from Ben Hutchings.
3) Because SCTP bypasses a good chunk of, and actually duplicates, the
logic of the ipv6 output path, some IPSEC things don't get done
properly. Integrate SCTP better into the ipv6 output path so that
these problems are fixed and such issues don't get missed in the
future either. From Daniel Borkmann.
4) Fix skge regressions added by the DMA mapping error return checking
added in v3.10, from Mikulas Patocka.
5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.
6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.
7) Fix error handling in tun_set_iff(), in particular don't leak
resources. From Jason Wang.
8) Prevent format-string injection into xen-netback driver, from Kees
Cook.
9) Fix regression added to netpoll ARP packet handling, in particular
check for the right ETH_P_ARP protocol code. From Sonic Zhang.
10) Try to deal with AMD IOMMU errors when using r8169 chips, from
Francois Romieu.
11) Cure freezes due to recent changes in the rt2x00 wireless driver,
from Stanislaw Gruszka.
12) Don't do SPI transfers (which can sleep) in interrupt context in
cw1200 driver, from Solomon Peachy.
13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
From Nithin Sujir.
14) Make xen_netbk_count_skb_slots() count the actual number of slots
that will be used, taking into consideration packing and other
issues that the transmit path will run into. From David Vrabel.
15) Use the correct maximum age when calculating the bridge
message_age_timer, from Chris Healy.
16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
Khoroshilov.
17) Netfilter conntrack extensions were converted to RCU but are not
always freed properly using kfree_rcu(). Fix from Michal Kubecek.
18) VF reset recovery not being done correctly in qlcnic driver, from
Manish Chopra.
19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.
20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.
21) Internal switch not initialized properly in bgmac driver, from Rafał
Miłecki.
22) Netlink messages report wrong local and remote addresses in IPv6
tunneling, from Ding Zhi.
23) ICMP redirects should not generate socket errors in DCCP and SCTP.
We're still working out how this should be handled for RAW and UDP
sockets. From Daniel Borkmann and Duan Jiong.
24) We've had several bugs wherein the network namespace's loopback
device gets accessed after it is free'd, NULL it out so that we can
catch these problems more readily. From Eric W Biederman.
25) Fix regression in TCP RTO calculations, from Neal Cardwell.
26) Fix too early free of xen-netback network device when VIFs still
exist. From Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
netconsole: fix a deadlock with rtnl and netconsole's mutex
netpoll: fix NULL pointer dereference in netpoll_cleanup
skge: fix broken driver
ip: generate unique IP identificator if local fragmentation is allowed
ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
xen-netback: Don't destroy the netdev until the vif is shut down
net:dccp: do not report ICMP redirects to user space
cnic: Fix crash in cnic_bnx2x_service_kcq()
bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
vxlan: Avoid creating fdb entry with NULL destination
tcp: fix RTO calculated from cached RTT
drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
net loopback: Set loopback_dev to NULL when freed
batman-adv: set the TAG flag for the vid passed to BLA
netfilter: nfnetlink_queue: use network skb for sequence adjustment
net: sctp: rfc4443: do not report ICMP redirects to user space
net: usb: cdc_ether: use usb.h macros whenever possible
net: usb: cdc_ether: fix checkpatch errors and warnings
net: usb: cdc_ether: Use wwan interface for Telit modules
ip6_tunnels: raddr and laddr are inverted in nl msg
...
This bug was introduced by commit
7a163bfb7c ("netconsole: avoid a crash with
multiple sysfs writers"). In store_enabled() we have the following
sequence: acquire nt->mutex then rtnl, but in the netconsole netdev
notifier we have rtnl then nt->mutex effectively leading to a deadlock.
The NULL pointer dereference that the above commit tries to fix is
actually due to another bug in netpoll_cleanup(). This is fixed by dropping
the mutex from the netdev notifier as it's already protected by rtnl.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch 136d8f377e broke the skge driver.
Note this part of the patch:
+ if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+ dev_kfree_skb(nskb);
+ goto resubmit;
+ }
+
pci_unmap_single(skge->hw->pdev,
dma_unmap_addr(e, mapaddr),
dma_unmap_len(e, maplen),
PCI_DMA_FROMDEVICE);
skb = e->skb;
prefetch(skb->data);
- skge_rx_setup(skge, e, nskb, skge->rx_buf_size);
The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.
This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Vasiliy Glazov <vascom2@gmail.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.
For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.
With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
- Minor updates and fixes to the Octeon ethernet driver in staging
- A fix to VGA_MAP_MEM() for 64 bit platforms
- Fix a workaround for 74K/1074K processors
- The symlink arch/mips/boot/dts/include/dt-bindings was pointing to a
a file with a name ending in \n. I think this may have been caused
by a git bug with with patches sent by email
- A build fix for VGA console on BCM1480-based systems
- Fix PCI device access via "/sys/bus/pci/.../resource0" or similar
work for Alchemy platforms
- Fix potential data leak on MIPS R5 cores. This doesn't add proper
support for any R5 features, just ensures a kernel without such
support will be secure to run
- Adding a macros for the CP0 Config5 register to be used by the R5 fix
- Make get_cycles() actually return something useful where possible
This also requires a preparatory patch for performance sake
- Fix a warning about the use of smp_processor_id() in preemptible
code. Again this includes a preparatory patch adding the
infrastructure to be used by the actual patch
- Finally remove pointless one-line comment
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix invalid symbolic link file
MIPS: PCI: pci-bcm1480: Include missing vt.h header
MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.
MIPS: Add MIPS R5 config5 register.
MIPS: PCI: Use pci_resource_to_user to map pci memory space properly
MIPS: 74K/1074K: Correct erratum workaround.
MIPS: Cleanup CP0 PRId and CP1 FPIR register access masks
MIPS: Remove useless comment about kprobe from arch/mips/Makefile
MIPS: Fix VGA_MAP_MEM macro.
MIPS: Reimplement get_cycles().
MIPS: Optimize current_cpu_type() for better code.
MIPS: Fix accessing to per-cpu data when flushing the cache
MIPS: Provide nice way to access boot CPU's data.
staging: octeon-ethernet: rgmii: enable interrupts that we can handle
staging: octeon-ethernet: remove skb alloc failure warnings
staging: octeon-ethernet: make dropped packets to consume NAPI budget
Pull ceph fixes from Sage Weil:
"These fix several bugs with RBD from 3.11 that didn't get tested in
time for the merge window: some error handling, a use-after-free, and
a sequencing issue when unmapping and image races with a notify
operation.
There is also a patch fixing a problem with the new ceph + fscache
code that just went in"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
fscache: check consistency does not decrement refcount
rbd: fix error handling from rbd_snap_name()
rbd: ignore unmapped snapshots that no longer exist
rbd: fix use-after free of rbd_dev->disk
rbd: make rbd_obj_notify_ack() synchronous
rbd: complete notifies before cleaning up osd_client and rbd_dev
libceph: add function to ensure notifies are complete
Pull drm radeon/nouveau/core fixes from Dave Airlie:
"Mostly radeon fixes, with some nouveau bios parser, ttm fix and a fix
for AST driver"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (42 commits)
drm/fb-helper: don't sleep for screen unblank when an oops is in progress
drm, ttm Fix uninitialized warning
drm/ttm: fix the tt_populated check in ttm_tt_destroy()
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
drm/nouveau/kms: enable for non-vga pci classes
drm/nouveau/bios/init: stub opcode 0xaa
drm/radeon: avoid UVD corruptions on AGP cards
drm/radeon: fix panel scaling with eDP and LVDS bridges
drm/radeon/dpm: rework auto performance level enable
drm/radeon: Fix hmdi typo
drm/radeon/dpm/rs780: fix force_performance state for same sclks
drm/radeon/dpm/rs780: don't enable sclk scaling if not required
drm/radeon/dpm/rs780: add some sanity checking to sclk scaling
drm/radeon/dpm/rs780: use drm_mode_vrefresh()
drm/udl: rip out set_need_resched
drm/ast: fix the ast open key function
drm/radeon/dpm: add bapm callback for kb/kv
drm/radeon/dpm: add bapm callback for trinity
drm/radeon/dpm: add infrastructure to properly handle bapm
...
Otherwise the system will burn even brighter and worse, leave the user
wondering what's going on exactly.
Since we already have a panic handler which will (try) to restore the
entire fbdev console mode, we can just bail out. Inspired by a patch from
Konstantin Khlebnikov. The callchain leading to this, cut&pasted from
Konstantin's original patch:
callstack:
panic()
bust_spinlocks(1)
unblank_screen()
vc->vc_sw->con_blank()
fbcon_blank()
fb_blank()
info->fbops->fb_blank()
drm_fb_helper_blank()
drm_fb_helper_dpms()
drm_modeset_lock_all()
mutex_lock(&dev->mode_config.mutex)
Note that the entire locking in the fb helper around panic/sysrq and kdbg
is ... non-existant. So we have a decent change of blowing up
everything. But since reworking this ties in with funny concepts like the
fbdev notifier chain or the impressive things which happen around
console_lock while oopsing, I'll leave that as an exercise for braver
souls than me.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix uninitialized warning.
drivers/gpu/drm/ttm/ttm_object.c: In function ‘ttm_base_object_lookup’:
drivers/gpu/drm/ttm/ttm_object.c:213:10: error: ‘base’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
kref_put(&base->refcount, ttm_release_base);
^
drivers/gpu/drm/ttm/ttm_object.c:221:26: note: ‘base’ was declared here
struct ttm_base_object *base;
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After a vmalloc failure in ttm_dma_tt_alloc_page_directory(),
ttm_dma_tt_init() will call ttm_tt_destroy() to cleanup, and end up
inside the driver's unpopulate() hook when populate() has never yet
been called.
On nouveau, the first issue to be hit because of this is that
dma_address[] may be a NULL pointer. After working around this,
ttm_pool_unpopulate() may potentially hit the same issue with
the pages[] array.
It seems to make more sense to avoid calling unpopulate on already
unpopulated TTMs than to add checks to all the implementations.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: stable@vger.kernel.org
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A couple of bios parser fixes (one for ancient chips, another for new ones - important in Optimus configs). Another to make sure KMS is enabled on certain Optimus configs, and a TTM failure path fix.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
drm/nouveau/kms: enable for non-vga pci classes
drm/nouveau/bios/init: stub opcode 0xaa
commit 104a43edb2
cnic: Use CHIP_NUM macros from bnx2x.h
changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not. There is another place in cnic that is still using
the old method to determine if FCoE is supported or not. The 2 methods
may not yield the same result after the network interface is brought down
and up. This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.
The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro. As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b9871bcfd2
bnx2x: VF RSS support - PF side
changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc. For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from v3.10 (probably commit f91e259041: "tty: Signal
foreground group processes in hangup") disassociate_ctty() sends SIGCONT
if tty && on_exit. This breaks LSB test-suite, in particular test8 in
_exit.c and test40 in sigcon5.c.
Put the "!on_exit" check back to restore the old behaviour.
Review by Peter Hurley:
"Yes, this regression was introduced by me in that commit. The effect
of the regression is that ptys will receive a SIGCONT when, in similar
circumstances, ttys would not.
The fact that two test vectors accidentally tripped over this
regression suggests that some other apps may as well.
Thanks for catching this"
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Karel Srot <ksrot@redhat.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit afbd8bae9c
vxlan: add implicit fdb entry for default destination
creates an implicit fdb entry for default destination. This results
in an invalid fdb entry if default destination is not specified.
For ex:
ip link add vxlan1 type vxlan id 100
creates the following fdb entry
00:00:00:00:00:00 dev vxlan1 dst 0.0.0.0 self permanent
This patch fixes this issue by creating an fdb entry only if a
valid default destination is specified.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clears following warnings :
WARNING: Use include <linux/io.h> instead of <asm/io.h>
WARNING: Use include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has recently turned up that we have a number of long standing bugs
in the network stack cleanup code with use of the loopback device
after it has been freed that have not turned up because in most cases
the storage allocated to the loopback device is not reused, when those
accesses happen.
Set looback_dev to NULL to trigger oopses instead of silent data corrupt
when we hit this class of bug.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove skb allocation failure warnings. They will trigger a page
allocation warning already. Also, one of the warnings was not ratelimited,
causing the box to lock up under heavy traffic & low memory.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Cc: linux-mips@linux-mips.org
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: richard@nod.at
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Patchwork: https://patchwork.linux-mips.org/patch/5811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We should count also dropped packets, otherwise the NAPI handler may
end up running too long.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: richard@nod.at
Patchwork: https://patchwork.linux-mips.org/patch/5809/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ben Hutchings says:
====================
Some bug fixes and future-proofing for the recently added SFC9120
support:
1. Minimal support for the 40G configuration.
2. Disable the incomplete PTP/hardware timestamping support.
3. Reset MAC stats properly after a firmware upgrade.
4. Re-check the datapath firmware capabilities after the controller is
reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use USB_DEVICE_AND_INTERFACE_INFO and USB_VENDOR_AND_INTERFACE_INFO
macros to reduce boilerplate.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: <stable@vger.kernel.org> # 3.0+ as far back as it applies cleanly
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. The max expected
value is 0xF, so now it should be possible to read decimal form ("15")
and hex form ("0xF").
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use separate table for alias entries in the ehea module, otherwise the
probe() function will operate on the separate ports instead of the
lhea-"root" entry of the device-tree
Addresses https://bugzilla.novell.com/show_bug.cgi?id=435215
[ Thadeu notes that: "... this issue might happen with the generation of
initrd, when the scripts check for /sys/class/net/eth0/device/modalias,
which links to the port device at
/sys/devices/ibmebus/23c00400.lhea/port0/" ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Olaf Hering <ohering@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer code update from Thomas Gleixner:
- armada SoC clocksource overhaul with a trivial merge conflict
- Minor improvements to various SoC clocksource drivers
* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
clocksource: armada-370-xp: Get reference fixed-clock by name
clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
clocksource: armada-370-xp: Fix device-tree binding
clocksource: armada-370-xp: Introduce new compatibles
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
clocksource: armada-370-xp: Simplify TIMER_CTRL register access
clocksource: armada-370-xp: Use BIT()
ARM: timer-sp: Set dynamic irq affinity
ARM: nomadik: add dynamic irq flag to the timer
clocksource: sh_cmt: 32-bit control register support
clocksource: em_sti: Convert to devm_* managed helpers
So far the only option to create a virtual AMP controller was by
setting a module parameter for the hci_vhci driver. This patch adds
the functionality to define inline to create either a BR/EDR or an
AMP controller.
In addition the client will be informed which HCI controller index
it got assigned. That is especially useful for automated end-to-end
testing.
To keep backwards compatibility with existing userspace, the command
for creating a controller type needs to be send right after opening
the device node. If the command is not send, it defaults back to
automatically creating a BR/EDR controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
To allow creating /dev/vhci device node, add the proper module alias for
this driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
It's not really necessary to have this processed
in a worker. There are no sleepable calls (and
actually shouldn't be).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is no longer used nor necessary since WMI
commands can block.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch prevents beacon misses in some case of
heavy load on a system.
If a beacon can't be transmitted directly from an
SWBA event it will be left in arvif->beacon and
transmission will be retried once TX credits
become available.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch removes HTC endpoint tx workers in
favour of direct command submission. This makes a
lot more sense for data path.
mac80211 queues are effectively stopped/woken up
in a more timely fashion preventing build up of
frames. It's possible to push more traffic than
the device/system is able to handle and have no
hiccups or performance degradation with UDP
traffic.
WMI commands will now report errors properly and
possibly block as they actively can wait for tx
credits to become available.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will be necessary for further changes in
command submission scheme.
Once HTC is cleaned up WMI commands will finally
block.
This requires for SWBA to be processed in a
non-atomic context for now. Once other necessary
changes are in this will be reverted.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will allow higher layers to anticipate and
act upon TX credits renewal. This will be
important for some future rework of WMI command
submission.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Credit calculation was overly complex
unnecessarily. Now skb dequeing is more unified.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When driver registration fails, we need to clean up the resources allocated
before. cxgb4 missed to destroy the workqueue allocated at the very beginning.
This patch destroies the workqueue when registration fails.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
running bonding in ALB mode requires that learning packets be sent periodically,
so that the switch knows where to send responding traffic. However, depending
on switch configuration, there may not be any need to send traffic at the
default rate of 3 packets per second, which represents little more than wasted
data. Allow the ALB learning packet interval to be made configurable via sysfs
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Acked-by: Veaceslav Falico <vfalico@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 8390f814 "atm: nicstar: re-use native mac_pton() helper" did a
usefull thing. However, mac_pton() returns 1 in the case of the successfully
parsed input. This patch fixes a typo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes sparse warnings when incorrectly handling the port number
and using int instead of unsigned int iterating through &vn->sock_list[].
Keeping the port as __be16 also makes things clearer wrt endianess.
Also, it was pointed out that vxlan_get_rx_port() had unnecessary checks
which got removed.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o At the time of firmware hang "adapter->need_fw_reset" variable gets
set but after re-initialization of firmware OR at the time of VF
re-initialization that variable was not getting cleared which
was leading to failure in VF reset recovery.Fix it by clearing
this variable before re-initializing VF
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/toshiba/ps3_gelic_net.c
It's a NOOP since 2.6.35 and I will remove it one day ;)
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
code in drivers/net/ethernet/smsc/
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/pasemi/pasemi_mac.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
code in drivers/net/ethernet/natsemi/
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/micrel/ks8851_mll.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/lantiq_etop.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/hp/hp100.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/freescale/fec_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Putting everything into VRAM seems to help.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We were using the wrong set_properly callback so we always
ended up with Full scaling even if something else (Center or
Full aspect) was selected.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Calling force_performance_level() from set_power_state()
doesn't work on some asics because the current power
state pointer has not been properly updated at that point.
Move the calls to force_performance_level() out of the
asic specific set_power_state() functions and into
the main power state sequence.
Fixes dpm resume on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I keep making that one, so checked if I was the only one. Apparently
not.
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the low and high sclks within a power state are the same,
there no need to enable sclk scaling. Enabling sclk scaling
can cause display stability issues on some boards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
If the low and high sclks are the same, there is no need to
enable sclk scaling. This causes display stability issues on
certain boards.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60857
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Since the clock scaling is based on fb divider adjustments,
make sure the other pll parameters are the same.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
This very much looks like copypasta from drm/i915's fault handler.
It was used there to duct-tape over issues around gpu reset handling.
Since that can't ever happen for udl and there's seemingly no other
reason for this just drop it.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Radeon drm fixes for 3.12. All over the place (display, dpm, uvd, etc.).
Also adds a couple more berlin pci ids.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux: (25 commits)
drm/radeon/dpm: add bapm callback for kb/kv
drm/radeon/dpm: add bapm callback for trinity
drm/radeon/dpm: add infrastructure to properly handle bapm
drm/radeon/dpm: handle bapm on kb/kv
drm/radeon/dpm: handle bapm on trinity
drm/radeon: expose DPM thermal thresholds through sysfs
drm/radeon: simplify driver data retrieval
drm/radeon/atom: workaround vbios bug in transmitter table on rs880 (v2)
drm/radeon/dpm: fix fallback for empty UVD clocks
drm/radeon: add command submission tracepoint
drm/radeon: remove stale radeon_fence_retire tracepoint
drm/radeon/r6xx: add a stubbed out set_uvd_clocks callback
drm/radeon: fix typo in PG flags
drm/radeon: add some additional berlin pci ids
drm/radeon/cik: update gpu_init for an additional berlin gpu
drm/radeon: add spinlocks for indirect register accesss
drm/radeon: protect concurrent smc register access with a spinlock
drm/radeon: dpm updates for KV
drm/radeon: signedness bug in kv_dpm.c
drm/radeon: clean up r600_free_extended_power_table()
...
Pull MIPS fixes from Ralf Baechle:
"These are four patches for three construction sites:
- Fix register decoding for the combination of multi-core processors
and multi-threading.
- Two more fixes that are part of the ongoing DECstation resurrection
work. One of these touches a DECstation-only network driver.
- Finally Markos' trivial build fix for the AP/SP support.
(With this applied now all MIPS defconfigs are building again)"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
MIPS: Fix SMP core calculations when using MT support.
MIPS: DECstation I/O ASIC DMA interrupt handling fix
MIPS: DECstation HRT initialization rearrangement
Pull x86 platform updates from Matthew Garrett:
"Nothing amazing here, almost entirely cleanups and minor bugfixes and
one bit of hardware enablement in the amilo-rfkill driver"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
platform/x86: panasonic-laptop: reuse module_acpi_driver
samsung-laptop: fix config build error
platform: x86: remove unnecessary platform_set_drvdata()
amilo-rfkill: Enable using amilo-rfkill with the FSC Amilo L1310.
wmi: parse_wdg() should return kernel error codes
hp_wmi: Fix unregister order in hp_wmi_rfkill_setup()
platform: replace strict_strto*() with kstrto*()
x86: irst: use module_acpi_driver to simplify the code
x86: smartconnect: use module_acpi_driver to simplify the code
platform samsung-q10: use ACPI instead of direct EC calls
thinkpad_acpi: add the ability setting TPACPI_LED_NONE by quirk
thinkpad_acpi: return -NODEV while operating uninitialized LEDs
This patch set is a set of driver updates (megaraid_sas, fnic, lpfc, ufs,
hpsa) we also have a couple of bug fixes (sd out of bounds and ibmvfc error
handling) and the first round of esas2r checker fixes and finally the much
anticipated big endian additions for megaraid_sas.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSNheiAAoJEDeqqVYsXL0MueMIAKD1kaB0oooRawE1+0vpKmyV
eE2M6trA8ofTeq0z1eNfRsVMkRsUuG9exW0CKS2z6mHiWwQ/zGbqT7ukveW+dMi3
mjKD0yO5ODk6bohWX/LiwZ6NGZSwC0dbIacXNy5ZsXKEizqwo1Jcc7qC/0AWn+o7
WpIL48XLPH0HqjQZ3dvgC6TWeFZOn9cKOWvQQq0S3ENALOx/eLZ+C7VrJLx5Magv
myNOUkTLzdlYglQfjaNO6et98k2oHTrzKwH7U2X6U75q7L8Pkj4RbNzce/Ge301V
u+R1w+BlbeTPdHopTBoTJupsvqDYBZxVwS7rr8nhSvfKduQppHnN6jX8yR4XNeM=
=RG3j
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI driver updates from James Bottomley:
"This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
ibmvfc error handling) and the first round of esas2r checker fixes and
finally the much anticipated big endian additions for megaraid_sas"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
[SCSI] fnic: fnic Driver Tuneables Exposed through CLI
[SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
[SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
[SCSI] fnic: Remove QUEUE_FULL handling code
[SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
[SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
[SCSI] sd: Fix potential out-of-bounds access
[SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
[SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
[SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
[SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
[SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
[SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
[SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
[SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
[SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
[SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
[SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
[SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
[SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
...
Pull input update from Dmitry Torokhov:
"The only change is David Hermann's new EVIOCREVOKE evdev ioctl that
allows safely passing file descriptors to input devices to session
processes and later being able to stop delivery of events through
these fds so that inactive sessions will no longer receive user input
that does not belong to them"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: evdev - add EVIOCREVOKE ioctl
Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset. This saves the driver from
having to keep track of an extra variable.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset. This saves the driver from
having to keep track of an extra variable.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci_enable_device_mem() will set device power state to D0,
so it's no need to do it again in alx_probe().
Also remove redundant PM Cap find code, because pci core
has been saved the pci device pm cap value.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unneeded local string buffers for constructing debug output. Also
cleans up debug calls that contain a single parameter so that they cannot
be accidentally parsed as format strings.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to ixgbe and e1000e.
Jacob provides a ixgbe patch to fix the configure_rx patch to properly
disable RSC hardware logic when a user disables it. Previously we only
disabled RSC in the queue settings, but this does not fully disable
hardware RSC logic which can lead to unexpected performance issues.
Emil provides three fixes for ixgbe. First fixes the ethtool loopback
test when DCB is enabled, where the frames may be modified on Tx
(by adding VLAN tag) which will fail the check on receive. Then a fix
for QSFP+ modules, limit the speed setting to advertise only one speed
at a time since the QSFP+ modules do not support auto negotiation.
Lastly, resolve an issue where the driver will display incorrect info
for QSFP+ modules that were inserted after the driver has been loaded.
David Ertman provides to fixes for e1000e, one removes a comparison to
the boolean value true where evaluating the lvalue will produce the
same result. The other fixes an error in the calculation of the
rar_entry_count, which causes a write of unkown/undefined register
space in the MAC to unknown/undefined register space in the PHY.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull aio changes from Ben LaHaise:
"First off, sorry for this pull request being late in the merge window.
Al had raised a couple of concerns about 2 items in the series below.
I addressed the first issue (the race introduced by Gu's use of
mm_populate()), but he has not provided any further details on how he
wants to rework the anon_inode.c changes (which were sent out months
ago but have yet to be commented on).
The bulk of the changes have been sitting in the -next tree for a few
months, with all the issues raised being addressed"
* git://git.kvack.org/~bcrl/aio-next: (22 commits)
aio: rcu_read_lock protection for new rcu_dereference calls
aio: fix race in ring buffer page lookup introduced by page migration support
aio: fix rcu sparse warnings introduced by ioctx table lookup patch
aio: remove unnecessary debugging from aio_free_ring()
aio: table lookup: verify ctx pointer
staging/lustre: kiocb->ki_left is removed
aio: fix error handling and rcu usage in "convert the ioctx list to table lookup v3"
aio: be defensive to ensure request batching is non-zero instead of BUG_ON()
aio: convert the ioctx list to table lookup v3
aio: double aio_max_nr in calculations
aio: Kill ki_dtor
aio: Kill ki_users
aio: Kill unneeded kiocb members
aio: Kill aio_rw_vect_retry()
aio: Don't use ctx->tail unnecessarily
aio: io_cancel() no longer returns the io_event
aio: percpu ioctx refcount
aio: percpu reqs_available
aio: reqs_active -> reqs_available
aio: fix build when migration is disabled
...
When copying the MAC RAR registers to PHY there is an error in the
calculation of the rar_entry_count, which causes a write of unknown/
undefined register space in the MAC to unknown/undefined register space in
the PHY.
This patch fixes the overrun with writing to the PHY RAR and also fixes the
ethtool offline register tests so that the correctly addressed registers
have the appropriate bitmasks for R/W and RO bits for affected parts.
Shawn Rader gets credit for finding and fixing the register overrun.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
CC: Shawn Rader <shawn.t.rader@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removing a comparison to the boolean value true where simply interrogating
the lvalue will produce the same result.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue where the driver will display incorrect info
for Q/SFP+ modules that were inserted after the driver has been loaded.
This patch adds a call to identify_phy() in ixgbe_get_settings() prior to
calling get_link_capabilities() which needs the PHY data in order to
determine the correct settings.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
QSFP+ modules do not support auto negotiation and should advertise only
one speed at a time.
This patch adds logic in ethtool to allow setting and reporting the
advertised speed at either 1Gbps or 10Gbps, but not both. Also limits
the speed set in ixgbe_sfp_link_config_subtask() to highest supported.
Previously the link was set to whatever the supported speeds were.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch disables DCB prior to running the loopback test.
When DCB is enabled the frames may be modified on Tx (by adding vlan tag)
which will fail the check on Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the configure_rx path in order to properly disable RSC
hardware logic when the user disables it. Previously we only disabled RSC in the
queue settings, but this does not fully disable hardware RSC logic which can
lead to some unexpected performance issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If tpkbd_probe_tp() bails out, the probe() function return an error,
but hid_hw_stop() is never called.
fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1003998
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When working on report indexes, always validate that they are in bounds.
Without this, a HID device could report a malicious feature report that
could trick the driver into a heap overflow:
[ 634.885003] usb 1-1: New USB device found, idVendor=0596, idProduct=0500
...
[ 676.469629] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
Note that we need to change the indexes from s8 to s16 as they can
be between -1 and 255.
CVE-2013-2897
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
logitech-dj HID driver to leak kernel memory contents to the device, or
trigger a NULL dereference during initialization:
[ 304.424553] usb 1-1: New USB device found, idVendor=046d, idProduct=c52b
...
[ 304.780467] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
[ 304.781409] IP: [<ffffffff815d50aa>] logi_dj_recv_send_report.isra.11+0x1a/0x90
CVE-2013-2895
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When dealing with usage_index, be sure to properly use unsigned instead of
int to avoid overflows.
When working on report fields, always validate that their report_counts are
in bounds.
Without this, a HID device could report a malicious feature report that
could trick the driver into a heap overflow:
[ 634.885003] usb 1-1: New USB device found, idVendor=0596, idProduct=0500
...
[ 676.469629] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
CVE-2013-2897
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
lenovo-tpkbd HID driver to write just beyond the output report allocation
during initialization, causing a heap overflow:
[ 76.109807] usb 1-1: New USB device found, idVendor=17ef, idProduct=6009
...
[ 80.462540] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
CVE-2013-2894
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
lg, lg3, and lg4 HID drivers to write beyond the output report allocation
during an event, causing a heap overflow:
[ 325.245240] usb 1-1: New USB device found, idVendor=046d, idProduct=c287
...
[ 414.518960] BUG kmalloc-4096 (Not tainted): Redzone overwritten
Additionally, while lg2 did correctly validate the report details, it was
cleaned up and shortened.
CVE-2013-2893
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
steelseries HID driver to write beyond the output report allocation
during initialization, causing a heap overflow:
[ 167.981534] usb 1-1: New USB device found, idVendor=1038, idProduct=1410
...
[ 182.050547] BUG kmalloc-256 (Tainted: G W ): Redzone overwritten
CVE-2013-2891
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver must validate the availability of the HID output report and
its size before it can write LED states via buzz_set_leds(). This stops
a heap overflow that is possible if a device provides a malicious HID
output report:
[ 108.171280] usb 1-1: New USB device found, idVendor=054c, idProduct=0002
...
[ 117.507877] BUG kmalloc-192 (Not tainted): Redzone overwritten
CVE-2013-2890
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org #3.11
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The zeroplus HID driver was not checking the size of allocated values
in fields it used. A HID device could send a malicious output report
that would cause the driver to write beyond the output report allocation
during initialization, causing a heap overflow:
[ 1442.728680] usb 1-1: New USB device found, idVendor=0c12, idProduct=0005
...
[ 1466.243173] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
CVE-2013-2889
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many drivers need to validate the characteristics of their HID report
during initialization to avoid misusing the reports. This adds a common
helper to perform validation of the report exisitng, the field existing,
and the expected number of values within the field.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.
Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle). Otherwise the handler is
reentered over and over again.
The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared. Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'. Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If rx_urb allocation fails in mcs_setup_urbs(), tx_urb leaks.
If mcs_receive_start() fails in mcs_net_open(), the both urbs are not deallocated.
The patch fixes the issues and by the way fixes label indentation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is down, CQs are freed. We must check the device state
to avoid issuing firmware commands on non existing CQs.
CC: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/dec/tulip/de4x5.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/amd/sun3lance.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/ibm/ehea/ehea_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/adi/bfin_mac.c.
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VM is providing an iSCSI target and the LUN is used by the
backend domain, the generated skbs for direct I/O writes to the disk
have large, multi-page skb->data but no frags.
With some lengths and starting offsets, xen_netbk_count_skb_slots()
would be one short because the simple calculation of
DIV_ROUND_UP(skb_headlen(), PAGE_SIZE) was not accounting for the
decisions made by start_new_rx_buffer() which does not guarantee
responses are fully packed.
For example, a skb with length < 2 pages but which spans 3 pages would
be counted as requiring 2 slots but would actually use 3 slots.
skb->data:
| 1111|222222222222|3333 |
Fully packed, this would need 2 slots:
|111122222222|22223333 |
But because the 2nd page wholy fits into a slot it is not split across
slots and goes into a slot of its own:
|1111 |222222222222|3333 |
Miscounting the number of slots means netback may push more responses
than the number of available requests. This will cause the frontend
to get very confused and report "Too many frags/slots". The frontend
never recovers and will eventually BUG.
Fix this by counting the number of required slots more carefully. In
xen_netbk_count_skb_slots(), more closely follow the algorithm used by
xen_netbk_gop_skb() by introducing xen_netbk_count_frag_slots() which
is the dry-run equivalent of netbk_gop_frag_copy().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 989038e217 ("tg3: Don't turn off
led on 5719 serdes port 0") added code to skip turning led off on port
0 of the 5719 since it powered down other ports. This workaround needs
to be enabled on the 5720 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
"This has been sitting in -next for a while with no objections and all
MIPS defconfigs except one are building fine; that one platform got
broken by another patch in your tree and I'm going to submit a patch
separately.
- a handful of fixes that didn't make 3.11
- a few bits of Octeon 3 support with more to come for a later
release
- platform enhancements for Octeon, ath79, Lantiq, Netlogic and
Ralink SOCs
- a GPIO driver for the Octeon
- some dusting off of the DECstation code
- the usual dose of cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits)
MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code
MIPS: kexec: Fix random crashes while loading crashkernel
MIPS: kdump: Skip walking indirection page for crashkernels
MIPS: DECstation HRT calibration bug fixes
MIPS: Export copy_from_user_page() (needed by lustre)
MIPS: Add driver for the built-in PCI controller of the RT3883 SoC
MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000
MIPS: ralink: Add support for reset-controller API
MIPS: ralink: mt7620: Add cpu-feature-override header
MIPS: ralink: mt7620: Add spi clock definition
MIPS: ralink: mt7620: Add wdt clock definition
MIPS: ralink: mt7620: Improve clock frequency detection
MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts
MIPS: ralink: mt7620: Add verbose ram info
MIPS: ralink: Probe clocksources from OF
MIPS: ralink: Add support for systick timer found on newer ralink SoC
MIPS: ralink: Add support for periodic timer irq
MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards
MIPS: Netlogic: Add support for USB on XLP2xx
MIPS: Netlogic: XLP2xx update for I2C controller
...
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity again this round for I/O performance optimizations
(per-cpu IDA pre-allocation for vhost + iscsi/target), and the
addition of new fabric independent features to target-core
(COMPARE_AND_WRITE + EXTENDED_COPY).
The main highlights include:
- Support for iscsi-target login multiplexing across individual
network portals
- Generic Per-cpu IDA logic (kent + akpm + clameter)
- Conversion of vhost to use per-cpu IDA pre-allocation for
descriptors, SGLs and userspace page pointer list
- Conversion of iscsi-target + iser-target to use per-cpu IDA
pre-allocation for descriptors
- Add support for generic COMPARE_AND_WRITE (AtomicTestandSet)
emulation for virtual backend drivers
- Add support for generic EXTENDED_COPY (CopyOffload) emulation for
virtual backend drivers.
- Add support for fast memory registration mode to iser-target (Vu)
The patches to add COMPARE_AND_WRITE and EXTENDED_COPY support are of
particular significance, which make us the first and only open source
target to support the full set of VAAI primitives.
Currently Linux clients are lacking upstream support to actually
utilize these primitives. However, with server side support now in
place for folks like MKP + ZAB working on the client, this logic once
reserved for the highest end of storage arrays, can now be run in VMs
on their laptops"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (50 commits)
target/iscsi: Bump versions to v4.1.0
target: Update copyright ownership/year information to 2013
iscsi-target: Bump default TCP listen backlog to 256
target: Fix >= v3.9+ regression in PR APTPL + ALUA metadata write-out
iscsi-target; Bump default CmdSN Depth to 64
iscsi-target: Remove unnecessary wait_for_completion in iscsi_get_thread_set
iscsi-target: Add thread_set->ts_activate_sem + use common deallocate
iscsi-target: Fix race with thread_pre_handler flush_signals + ISCSI_THREAD_SET_DIE
target: remove unused including <linux/version.h>
iser-target: introduce fast memory registration mode (FRWR)
iser-target: generalize rdma memory registration and cleanup
iser-target: move rdma wr processing to a shared function
target: Enable global EXTENDED_COPY setup/release
target: Add Third Party Copy (3PC) bit in INQUIRY response
target: Enable EXTENDED_COPY setup in spc_parse_cdb
target: Add support for EXTENDED_COPY copy offload emulation
target: Avoid non-existent tg_pt_gp_mem in target_alua_state_check
target: Add global device list for EXTENDED_COPY
target: Make helpers non static for EXTENDED_COPY command setup
target: Make spc_parse_naa_6h_vendor_specific non static
...
Merge more patches from Andrew Morton:
"The rest of MM. Plus one misc cleanup"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
mm/Kconfig: add MMU dependency for MIGRATION.
kernel: replace strict_strto*() with kstrto*()
mm, thp: count thp_fault_fallback anytime thp fault fails
thp: consolidate code between handle_mm_fault() and do_huge_pmd_anonymous_page()
thp: do_huge_pmd_anonymous_page() cleanup
thp: move maybe_pmd_mkwrite() out of mk_huge_pmd()
mm: cleanup add_to_page_cache_locked()
thp: account anon transparent huge pages into NR_ANON_PAGES
truncate: drop 'oldsize' truncate_pagecache() parameter
mm: make lru_add_drain_all() selective
memcg: document cgroup dirty/writeback memory statistics
memcg: add per cgroup writeback pages accounting
memcg: check for proper lock held in mem_cgroup_update_page_stat
memcg: remove MEMCG_NR_FILE_MAPPED
memcg: reduce function dereference
memcg: avoid overflow caused by PAGE_ALIGN
memcg: rename RESOURCE_MAX to RES_COUNTER_MAX
memcg: correct RESOURCE_MAX to ULLONG_MAX
mm: memcg: do not trap chargers with full callstack on OOM
mm: memcg: rework and document OOM waiting and wakeup
...
We use NR_ANON_PAGES as base for reporting AnonPages to user. There's
not much sense in not accounting transparent huge pages there, but add
them on printing to user.
Let's account transparent huge pages in NR_ANON_PAGES in the first place.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Ning Qu <quning@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile 4 from Al Viro:
"list_lru pile, mostly"
This came out of Andrew's pile, Al ended up doing the merge work so that
Andrew didn't have to.
Additionally, a few fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (42 commits)
super: fix for destroy lrus
list_lru: dynamically adjust node arrays
shrinker: Kill old ->shrink API.
shrinker: convert remaining shrinkers to count/scan API
staging/lustre/libcfs: cleanup linux-mem.h
staging/lustre/ptlrpc: convert to new shrinker API
staging/lustre/obdclass: convert lu_object shrinker to count/scan API
staging/lustre/ldlm: convert to shrinkers to count/scan API
hugepage: convert huge zero page shrinker to new shrinker API
i915: bail out earlier when shrinker cannot acquire mutex
drivers: convert shrinkers to new count/scan API
fs: convert fs shrinkers to new scan/count API
xfs: fix dquot isolation hang
xfs-convert-dquot-cache-lru-to-list_lru-fix
xfs: convert dquot cache lru to list_lru
xfs: rework buffer dispose list tracking
xfs-convert-buftarg-lru-to-generic-code-fix
xfs: convert buftarg LRU to generic code
fs: convert inode and dentry shrinking to be node aware
vmscan: per-node deferred work
...
Commit c8d68e6be1
(tuntap: multiqueue support) only call free_netdev() on error in
tun_set_iff(). This causes several issues:
- memory of tun security were leaked
- use after free since the flow gc timer was not deleted and the tfile
were not detached
This patch solves the above issues.
Reported-by: Wannes Rombouts <wannes.rombouts@epitech.eu>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure a format string cannot accidentally leak into the
kthread_run() call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A small batch of fixes that have trickled in over the last week of the
merge window.
Also included are few small devicetree updates for sunxi, since it
enables me to use one of their newer boards (cubieboard2) for additional
test coverage. The support for that SoC is new for 3.12, so there's no
exposure to new regressions due to it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HLjK
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A small batch of fixes that have trickled in over the last week of the
merge window.
Also included are few small devicetree updates for sunxi, since it
enables me to use one of their newer boards (cubieboard2) for
additional test coverage. The support for that SoC is new for 3.12,
so there's no exposure to new regressions due to it"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: sun7i: olinuxino-micro: Enable the EMAC
ARM: dts: sun7i: cubieboard2: Enable the EMAC
ARM: dts: sun7i: Add the muxing options for the EMAC
ARM: dts: sun7i: Enable the Ethernet in the A20
i2c: davinci: Fix bad dev_get_platdata() conversion
ARM: vexpress: allow dcscb and tc2_pm in a combined ARMv6+v7 build
ARM: shmobile: lager: Do not use register_type field of struct sh_eth_plat_data
ARM: pxa: ssp: Check return values from phandle lookups
ARM: PCI: versatile: Fix SMAP register offsets
ARM: PCI: versatile: Fix PCI I/O
ARM: PCI: versatile: Fix map_irq function to match hardware
ARM: ep93xx: Don't use modem interface on the second UART
ARM: shmobile: r8a7779: Update early timer initialisation order
Flow control is defined in the four EEPROM sections but the driver only reads
from section 0.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where some ports can fail to initialize on a
cold boot. This patch adds an additional call to read the PHY id for i354
devices in order workaround the hardware problem.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull led updates from Bryan Wu:
"Sorry for the late pull request, since I'm just back from vacation.
LED subsystem updates for 3.12:
- pca9633 driver DT supporting and pca9634 chip supporting
- restore legacy device attributes for lp5521
- other fixing and updates"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (28 commits)
leds: wm831x-status: Request a REG resource
leds: trigger: ledtrig-backlight: Fix invalid memory access in fb_event notification callback
leds-pca963x: Fix device tree parsing
leds-pca9633: Rename to leds-pca963x
leds-pca9633: Add mutex to the ledout register
leds-pca9633: Unique naming of the LEDs
leds-pca9633: Add support for PCA9634
leds: lp5562: use LP55xx common macros for device attributes
Documentation: leds-lp5521,lp5523: update device attribute information
leds: lp5523: remove unnecessary writing commands
leds: lp5523: restore legacy device attributes
leds: lp5523: LED MUX configuration on initializing
leds: lp5523: make separate API for loading engine
leds: lp5521: remove unnecessary writing commands
leds: lp5521: restore legacy device attributes
leds: lp55xx: add common macros for device attributes
leds: lp55xx: add common data structure for program
Documentation: leds: Fix a typo
leds: ss4200: Fix incorrect placement of __initdata
leds: clevo-mail: Fix incorrect placement of __initdata
...
This round the updates contain:
* A new driver for the Freescale PAMU IOMMU from Varun Sethi.
This driver has cooked for a while and required changes to the
IOMMU-API and infrastructure that were already merged before.
* Updates for the ARM-SMMU driver from Will Deacon
* Various fixes, the most important one is probably a fix from
Alex Williamson for a memory leak in the VT-d page-table
freeing code
In summary not all that much. The biggest part in the diffstat is the
new PAMU driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UZoD
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU Updates from Joerg Roedel:
"This round the updates contain:
- A new driver for the Freescale PAMU IOMMU from Varun Sethi.
This driver has cooked for a while and required changes to the
IOMMU-API and infrastructure that were already merged before.
- Updates for the ARM-SMMU driver from Will Deacon
- Various fixes, the most important one is probably a fix from Alex
Williamson for a memory leak in the VT-d page-table freeing code
In summary not all that much. The biggest part in the diffstat is the
new PAMU driver"
* tag 'iommu-updates-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
intel-iommu: Fix leaks in pagetable freeing
iommu/amd: Fix resource leak in iommu_init_device()
iommu/amd: Clean up unnecessary MSI/MSI-X capability find
iommu/arm-smmu: Simplify VMID and ASID allocation
iommu/arm-smmu: Don't use VMIDs for stage-1 translations
iommu/arm-smmu: Tighten up global fault reporting
iommu/arm-smmu: Remove broken big-endian check
iommu/fsl: Remove unnecessary 'fsl-pamu' prefixes
iommu/fsl: Fix whitespace problems noticed by git-am
iommu/fsl: Freescale PAMU driver and iommu implementation.
iommu/fsl: Add additional iommu attributes required by the PAMU driver.
powerpc: Add iommu domain pointer to device archdata
iommu/exynos: Remove dead code (set_prefbuf)
- fix a preemption bug in xen/balloon.c;
- remove an harmful BUG_ON in xen/balloon.c that can trigger in
non-erroneous situations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=kWtE
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.12-rc0-tag-three' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen balloon driver bug-fixes from Stefano Stabellini:
- fix a preemption bug in xen/balloon.c;
- remove an harmful BUG_ON in xen/balloon.c that can trigger in
non-erroneous situations.
* tag 'stable/for-linus-3.12-rc0-tag-three' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: remove BUG_ON in increase_reservation
xen/balloon: ensure preemption is disabled when using a scratch page
1) ACPI-based PCI hotplug (ACPIPHP) fixes related to spurious events
After the recent ACPIPHP changes we've seen some interesting breakage
on a system that triggers device check notifications during boot for
non-existing devices. Although those notifications are really
spurious, we should be able to deal with them nevertheless and that
shouldn't introduce too much overhead. Four commits to make that
work properly.
2) Memory hotplug and hibernation mutual exclusion rework
This was maent to be a cleanup, but it happens to fix a classical
ABBA deadlock between system suspend/hibernation and ACPI memory
hotplug which is possible if they are started roughly at the same
time. Three commits rework memory hotplug so that it doesn't
acquire pm_mutex and make hibernation use device_hotplug_lock
which prevents it from racing with memory hotplug.
3) ACPI Intel LPSS (Low-Power Subsystem) driver crash fix
The ACPI LPSS driver crashes during boot on Apple Macbook Air with
Haswell that has slightly unusual BIOS configuration in which one
of the LPSS device's _CRS method doesn't return all of the information
expected by the driver. Fix from Mika Westerberg, for stable.
4) ACPICA fix related to Store->ArgX operation
AML interpreter fix for obscure breakage that causes AML to be
executed incorrectly on some machines (observed in practice). From
Bob Moore.
5) ACPI core fix for PCI ACPI device objects lookup
There still are cases in which there is more than one ACPI device
object matching a given PCI device and we don't choose the one that
the BIOS expects us to choose, so this makes the lookup take more
criteria into account in those cases.
6) Fix to prevent cpuidle from crashing in some rare cases
If the result of cpuidle_get_driver() is NULL, which can happen on
some systems, cpuidle_driver_ref() will crash trying to use that
pointer and the Daniel Fu's fix prevents that from happening.
7) cpufreq fixes related to CPU hotplug
Stephen Boyd reported a number of concurrency problems with cpufreq
related to CPU hotplug which are addressed by a series of fixes
from Srivatsa S Bhat and Viresh Kumar.
8) cpufreq fix for time conversion in time_in_state attribute
Time conversion carried out by cpufreq when user space attempts to
read /sys/devices/system/cpu/cpu*/cpufreq/stats/time_in_state won't
work correcty if cputime_t doesn't map directly to jiffies. Fix
from Andreas Schwab.
9) Revert of a troublesome cpufreq commit
Commit 7c30ed5 (cpufreq: make sure frequency transitions are
serialized) was intended to address some known concurrency problems
in cpufreq related to the ordering of transitions, but unfortunately
it introduced several problems of its own, so I decided to revert it
now and address the original problems later in a more robust way.
10) Intel Haswell CPU models for intel_pstate from Nell Hardcastle.
11) cpufreq fixes related to system suspend/resume
The recent cpufreq changes that made it preserve CPU sysfs attributes
over suspend/resume cycles introduced a possible NULL pointer
dereference that caused it to crash during the second attempt to
suspend. Three commits from Srivatsa S Bhat fix that problem and a
couple of related issues.
12) cpufreq locking fix
cpufreq_policy_restore() should acquire the lock for reading, but
it acquires it for writing. Fix from Lan Tianyu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=U/Jw
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-fixes-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"All of these commits are fixes that have emerged recently and some of
them fix bugs introduced during this merge window.
Specifics:
1) ACPI-based PCI hotplug (ACPIPHP) fixes related to spurious events
After the recent ACPIPHP changes we've seen some interesting
breakage on a system that triggers device check notifications
during boot for non-existing devices. Although those
notifications are really spurious, we should be able to deal with
them nevertheless and that shouldn't introduce too much overhead.
Four commits to make that work properly.
2) Memory hotplug and hibernation mutual exclusion rework
This was maent to be a cleanup, but it happens to fix a classical
ABBA deadlock between system suspend/hibernation and ACPI memory
hotplug which is possible if they are started roughly at the same
time. Three commits rework memory hotplug so that it doesn't
acquire pm_mutex and make hibernation use device_hotplug_lock
which prevents it from racing with memory hotplug.
3) ACPI Intel LPSS (Low-Power Subsystem) driver crash fix
The ACPI LPSS driver crashes during boot on Apple Macbook Air with
Haswell that has slightly unusual BIOS configuration in which one
of the LPSS device's _CRS method doesn't return all of the
information expected by the driver. Fix from Mika Westerberg, for
stable.
4) ACPICA fix related to Store->ArgX operation
AML interpreter fix for obscure breakage that causes AML to be
executed incorrectly on some machines (observed in practice).
From Bob Moore.
5) ACPI core fix for PCI ACPI device objects lookup
There still are cases in which there is more than one ACPI device
object matching a given PCI device and we don't choose the one
that the BIOS expects us to choose, so this makes the lookup take
more criteria into account in those cases.
6) Fix to prevent cpuidle from crashing in some rare cases
If the result of cpuidle_get_driver() is NULL, which can happen on
some systems, cpuidle_driver_ref() will crash trying to use that
pointer and the Daniel Fu's fix prevents that from happening.
7) cpufreq fixes related to CPU hotplug
Stephen Boyd reported a number of concurrency problems with
cpufreq related to CPU hotplug which are addressed by a series of
fixes from Srivatsa S Bhat and Viresh Kumar.
8) cpufreq fix for time conversion in time_in_state attribute
Time conversion carried out by cpufreq when user space attempts to
read /sys/devices/system/cpu/cpu*/cpufreq/stats/time_in_state
won't work correcty if cputime_t doesn't map directly to jiffies.
Fix from Andreas Schwab.
9) Revert of a troublesome cpufreq commit
Commit 7c30ed5 (cpufreq: make sure frequency transitions are
serialized) was intended to address some known concurrency
problems in cpufreq related to the ordering of transitions, but
unfortunately it introduced several problems of its own, so I
decided to revert it now and address the original problems later
in a more robust way.
10) Intel Haswell CPU models for intel_pstate from Nell Hardcastle.
11) cpufreq fixes related to system suspend/resume
The recent cpufreq changes that made it preserve CPU sysfs
attributes over suspend/resume cycles introduced a possible NULL
pointer dereference that caused it to crash during the second
attempt to suspend. Three commits from Srivatsa S Bhat fix that
problem and a couple of related issues.
12) cpufreq locking fix
cpufreq_policy_restore() should acquire the lock for reading, but
it acquires it for writing. Fix from Lan Tianyu"
* tag 'pm+acpi-fixes-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
cpufreq: Acquire the lock in cpufreq_policy_restore() for reading
cpufreq: Prevent problems in update_policy_cpu() if last_cpu == new_cpu
cpufreq: Restructure if/else block to avoid unintended behavior
cpufreq: Fix crash in cpufreq-stats during suspend/resume
intel_pstate: Add Haswell CPU models
Revert "cpufreq: make sure frequency transitions are serialized"
cpufreq: Use signed type for 'ret' variable, to store negative error values
cpufreq: Remove temporary fix for race between CPU hotplug and sysfs-writes
cpufreq: Synchronize the cpufreq store_*() routines with CPU hotplug
cpufreq: Invoke __cpufreq_remove_dev_finish() after releasing cpu_hotplug.lock
cpufreq: Split __cpufreq_remove_dev() into two parts
cpufreq: Fix wrong time unit conversion
cpufreq: serialize calls to __cpufreq_governor()
cpufreq: don't allow governor limits to be changed when it is disabled
ACPI / bind: Prefer device objects with _STA to those without it
ACPI / hotplug / PCI: Avoid parent bus rescans on spurious device checks
ACPI / hotplug / PCI: Use _OST to notify firmware about notify status
ACPI / hotplug / PCI: Avoid doing too much for spurious notifies
ACPICA: Fix for a Store->ArgX when ArgX contains a reference to a field.
ACPI / hotplug / PCI: Don't trim devices before scanning the namespace
...
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
struct ce_sendlist is useless as we always add just one buffer onto it.
And most importantly, it's ugly as it doesn't use skb properly.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The peer PHY mode for 11ac operation needs to be determined
properly based on the channel bandwidth being used. Fix
this so that the proper mode is given to the firmware.
kvalo: earlier we used 11na-ht20 in STA mode for 11ac AP peer, this
patch changes that to 11ac-vht80. I didn't notice any change in
throughput in my tests, but nevertheless it's the right thing
to do.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull watchdog updates from Wim Van Sebroeck:
- New watchdog driver for Allwinner A10/A13
- some devm_ioremap_resource simplifications
- a s3c2410_wdt change that removes the global variables
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: s3c2410_wdt: simplify use of devm_ioremap_resource
watchdog: simplify platform_get_resource_byname/devm_ioremap_resource
watchdog: ts72xx_wdt: simplify use of devm_ioremap_resource
watchdog: nuc900_wdt.c: simplify use of devm_ioremap_resource
watchdog: sunxi: New watchdog driver for Allwinner A10/A13
watchdog: s3c2410_wdt: remove the global variables
Just to unify with the rest of debug messages. Minimal functional changes,
only major ones are removal of the awkward "else" style in debug
messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
