During S3->S0 transition, sometime ROM init fails because of
authentication engine loads later than the OS. In this case driver
waits for a longer period and then retries the FW download causing
huge delay in resume time of audio device.
To avoid this, ROM INIT wait time is set to a optimal value and
increased the retries for firmware download.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Store the DSP firmware/library at boot, so that for S3 to S0 transition
use the stored ctx for downloading the firmware to DSP memory.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is next gen SoC, so add the IDs for Geminilake.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake has two different devices connected to the same SSP, so use
device_type check to get correct device configuration.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch create entry in sysfs file system to report the
platform_id = "pci-id-oem_id-oem_table_id-oem_revision"
for board identification.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA channel(stream tag) used by the HDA link need to programmed in
codec so that codec receives packet from the link associated with the
same channel.
DMA channel is allocated in link BE dai hw_params, the same needs to be
set for the BE codec dai. Instead of using get/set dma_data(), use
dai_ops snd_soc_dai_set_tdm_slot() to set the stream tag.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In system suspend, the firmware pipelines will be deleted and there
is no need to save the pipeline context. Driver will save the DPIB and
LPIB pointers in suspend.
In system resume, the firmware pipelines will be created again and the
RD/RW pointers in the Firmware buffer points to the base address. So
need to fetch the non-played data again to firmware buffer. LPIB
indicates the HW rendered position.
Instead of setting DPIB as resume point, set it to LPIB to restore from
the HW render position so that DMA would fetch the non-played data one
more time.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When pipe is pass-through, BE and FE modules are defined inside
a pipe, reset of pipe will be done in FE DAI prepare. So don't
reset in the BE prepare.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Saved firmware ctx was not never released, so release Firmware
ctx in cleanup routine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the optimized dsp_register_poll API to poll the DSP firmware
status register rather than open coding it.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing the topology manifest info directly to IPC library,
define the manifest info in topology and use this in IPC Library.
This will remove the dependency on topology interface definition with
IPC library.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a module is not available in a pipeline, fail safely rather than
causing oops.
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removed the unused function skl_get_format as the format is calculated
directly using the HDA core API.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds helper function to configure the host/link DMA when
the DMA is in decoupled mode.
Next patch adds the usage of this helper routines for configuring
DMA in Mixer event handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system is suspended when PCM was paused/stopped, restart doesn't
configure DMA as it is we are in Pause state and results in IO error
eventually.
Configure host/link DMA before initializing DSP Gateway copier module
instead of DAI prepare(). So moved DMA configuration to mixer PRE_PMD
widget handler instead of DAI prepare.
This uses previously added new API to do the configuration and removes
old DAI prepare code.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To configure Host/Link DMA, additionally link index and format
are required based on the hw params. So added these parameters in
the pipe params and in hw_params the pipe params are updated.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In skl_tplg_mixer_dapm_post_pmd_event(), a variable 'ret' is initialized but
not used.
We don't check return of skl_delete_pipe, so remove the assignment as
well, so remove this variable.
sound/soc/intel/skylake/skl-topology.c: In function ‘skl_tplg_mixer_dapm_post_pmd_event’:
sound/soc/intel/skylake/skl-topology.c:976:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret = 0;
^
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usage pattern of kthread worker in Intel SST drivers can be
replaced gracefully with the normal workqueue, which is more light-
weight and easier to manage in general. Let's do it.
While in the replacement, move the schedule_work() call inside the
spinlock for excluding the race, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that I2S conflig blob structure is no longer in use, remove it.
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S blob config structure can change between DSP copier module versions.
We are not modifying these structures anyway and NHLT blobs specify them
properly, so use the blob directly to send the dma_control ipc instead
of using the predefined I2S blob config structure.
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While going to suspend, if we have any pending D0i3 work scheduled,
flush that and force the DSP to goto D0i3 mode before going to suspend.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were invoking pci_disable_device() while going to suspend-to-idle and
pci_enable_device() while coming back to active state.
Turns out that we do not need these calls as we only need system to be
wake capable when in suspend-to-idle state. The wake capability is
already done by enable_irq_wake() calls, so remove these unwanted calls
in driver.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For device opened/closed, we check the D0i3 capability for the device
and invoke skl_tplg_d0i3_get/put, which counts the use case based on the
mode supported.
These counters are then used to decide if the device can enter D0i3 mode
of streaming or non-streaming or no D0i3.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all use cases can support Doi3. Only certain use cases like hot word
detection, deep buffering can support D0i3 based on resource requirement.
So, pass the D0i3 capability for the FE/BE copier using topology. This will
be used to take a decision for D0i3 mode entry/exit.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For D0i3, we need to tell DSP to run the pipelines in LP mode. This
information is kept in topology and passed to driver as an attribute
for pipe.
So add a new tuple for lpmode and program the pipe based on value set.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver needs two DSP callback, one to set D0i0 (active) and D0i3
(low-power) states.
Add these callbacks in dsp ops and implement them for broxton platforms.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To set the controller in D0i3 mode, the driver needs to set D0i3C
register after DSP is quiesced. Since the D0iX entry/exit is done by IPC,
add this as callback so that it can be invoked from IPC module.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio DSP supports intermediate power states between D0 and D3
states. These states are D0i0 and D0i3 states.
Collectively we refer these two states as D0iX states.
To set or wake up from these states, driver also needs to send an IPC "Set D0iX
IPC" before doing anything else.
Add support for this new IPC messages.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPIB is read currently from a buffer position in memory (indicated by
the registers DPIB[U|L]BASE).Driver reads the position buffer on BDL
completion interrupts to report the DMA position. But the BDL completion
interrupt only indicates the last DMA transfer of the buffer is
completed at the Intel HD Audio subsystem boundary. The periodic DMA
Position-in-Buffer writes may be scheduled at the same time or later
than the MSI and does not guarantee to reflect the position of the last
buffer that was transferred.
Whereas DPIB register in HDA space(vendor specific register indicated by
SDxDPIB) reflects the actual data that is transferred. Hence update the
position based on DPIB for playback.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI codec is required to be powered up before controller initialization
for successful enumeration of codec. If the probe fails it needs to be
powered off to balance the power state of HDMI codec.
This fix balances the reference count in the error path before turning
off the codec.
Reported-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"*val" is a u64. It definitely looks like we intend to use the high 32
bits as well.
Fixes: 700a9a63f9 ("ASoC: Intel: Skylake: Add module instance id generation APIs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_probe() releases a runtime pm ref unconditionally wheras
skl_remove() acquires one only if the device is wakeup capable.
Thus if the device is not wakeup capable, unloading and reloading
the module will result in the refcount being decreased below 0.
Fix it.
Fixes: d8c2dab838 ("ASoC: Intel: Add Skylake HDA audio driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently there is a memory leak of module on a ENOMEM return path.
Fix this by kfree'ing module before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trival fix, some dev_* messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since modules ids are generated dynamically, we do not know the id
associate with modules in another pipelines. This limits our ability to
tell DSP about neighbouring modules.
So add a table for quick referencing of allocated module ids.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Post bind parameters of KPB module contains the instance id's of
neighbouring modules in the sink path
Now that module instance ids are generated dynamically we need to update
these parameters as well, so use the table created and update the ids
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use private id's of module instances that are generated during
init_module for the IPC messages to DSP. These id's are freed
up during delete pipeline.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver needs to send unique module instance id to firmware while
creating the module and uses this id to communicate with DSP for setting
parameters while audio use case is ongoing.
But, we have upper bound of instance ID. The current IDs are coming from
topology but it doesn't know the upper bound and can't assign unique
id's subject to upper bounds as we can create a big graph but not all
parts running at same time.
This patch adds a 128bit unique id management routines which are built
on top of ffz() for faster implementation. Unfortunately ffz() works on
32bits values, so additional code is added on top of ffz() to create a
128bit unique id.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We also support 32bit playback, so add that in DAI capabilities.
Signed-off-by: Samaga Krishna <samaga.krishna@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_pcm_ops structures that are only stored in the ops field of a
snd_soc_platform_driver structure or passed as the third argument to
snd_pcm_set_ops. The corresponding field or parameter is declared const,
so snd_pcm_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_pcm_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_platform_driver e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i;
expression e1, e2;
position p;
@@
snd_pcm_set_ops(e1, e2, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_pcm_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_pcm_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
There could be more than one loadable module in a pipeline.
So unload all modules whilst parsing the list.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA control IPC structure wrong config array length,
So corrected the size
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While converting to new core hda capability parsing, one instance of
check had inverted logic which was converted wrongly.
Fixes: ec8ae5703d (ALSA: convert users to core bus_parse_capabilities)
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
