This function can't succeed if dp->pl is NULL. It will Oops inside the
call to return phylink_ethtool_get_eee(dp->pl, e);
Fixes: 1be52e97ed ("dsa: slave: eee: Allow ports to use phylink")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unbalance of master's promiscuity or allmulti will happen after ifdown
and ifup a slave interface which is in a bridge.
When we ifdown a slave interface , both the 'dsa_slave_close' and
'dsa_slave_change_rx_flags' will clear the master's flags. The flags
of master will be decrease twice.
In the other hand, if we ifup the slave interface again, since the
slave's flags were cleared the 'dsa_slave_open' won't set the master's
flag, only 'dsa_slave_change_rx_flags' that triggered by 'br_add_if'
will set the master's flags. The flags of master is increase once.
Only propagating flag changes when a slave interface is up makes
sure this does not happen. The 'vlan_dev_change_rx_flags' had the
same problem and was fixed, and changes here follows that fix.
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Rundong Ge <rdong.ge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will enable vetoing of FDB entries. Make it possible
to communicate details of why an FDB entry is not acceptable back to the
user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not currently way to infer the port number through sysfs that
is being used as the CPU port number. Overlay a ndo_get_phys_port_name()
operation onto the DSA master network device in order to retrieve that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the destination address is link local, add override bit into the
switch tag to let such a packet through the switch even if the port is
blocked.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out common code from the tag_ksz , so that the code can be used
with other KSZ family switches which use differenly sized tags.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous change tries to set the MTU on the master device to take
into account the DSA overheads. This patch tries to reset the master
device back to the default MTU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA tagging of frames sent over the master interface to the switch
increases the size of the frame. Such frames can then be bigger than
the normal MTU of the master interface, and it may drop them. Use the
overhead information from the tagger to set the MTU of the master
device to include this overhead.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each DSA tag protocol needs to add additional headers to the Ethernet
frame in order to direct it towards a specific switch egress port. It
must also remove the head from a frame received from a
switch. Indicate the maximum size of these headers in the tag protocol
ops structure, so the core can take these overheads into account.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While introducing the DSA tagging protocol attribute, it was added to the DSA
slave network devices, but those actually see untagged traffic (that is their
whole purpose). Correct this mistake by putting the tagging sysfs attribute
under the DSA master network device where this is the information that we need.
While at it, also correct the sysfs documentation mistake that missed the
"dsa/" directory component of the attribute.
Fixes: 98cdb48071 ("net: dsa: Expose tagging protocol to user-space")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an explicit check in rocker_world_port_obj_vlan_add(),
dsa_slave_switchdev_event() resp. port_switchdev_event(), VLAN objects
that are added to a device that is not a front-panel port device are
ignored. Therefore this check is immaterial.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop switchdev_ops.switchdev_port_obj_add and _del. Drop the uses of
this field from all clients, which were migrated to use switchdev
notification in the previous patches.
Add a new function switchdev_port_obj_notify() that sends the switchdev
notifications SWITCHDEV_PORT_OBJ_ADD and _DEL.
Update switchdev_port_obj_del_now() to dispatch to this new function.
Drop __switchdev_port_obj_add() and update switchdev_port_obj_add()
likewise.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.
DSA currently doesn't support any other uppers than bridge.
SWITCHDEV_OBJ_ID_HOST_MDB and _PORT_MDB objects are always notified on
the bridge port device. Thus the only case that a stacked device could
be validly referenced by port object notifications are bridge
notifications for VLAN objects added to the bridge itself. But the
driver explicitly rejects such notifications in dsa_port_vlan_add(). It
is therefore safe to assume that the only interesting case is that the
notification is on a front-panel port netdevice. Therefore keep the
filtering by dsa_slave_dev_check() in place.
To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking
notifier chain. Dispatch to rocker_port_obj_add() resp. _del() to
maintain the behavior that the switchdev operation based code currently
has.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a problem introduced by:
commit 2cde6acd49 ("netpoll: Fix __netpoll_rcu_free so that it can hold the rtnl lock")
When using netconsole on a bond, __netpoll_cleanup can asynchronously
recurse multiple times, each __netpoll_free_async call can result in
more __netpoll_free_async's. This means there is now a race between
cleanup_work queues on multiple netpoll_info's on multiple devices and
the configuration of a new netpoll. For example if a netconsole is set
to enable 0, reconfigured, and enable 1 immediately, this netconsole
will likely not work.
Given the reason for __netpoll_free_async is it can be called when rtnl
is not locked, if it is locked, we should be able to execute
synchronously. It appears to be locked everywhere it's called from.
Generalize the design pattern from the teaming driver for current
callers of __netpoll_free_async.
CC: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an FDB entry only ceases being offloaded when it is deleted.
This changes with VxLAN encapsulation.
Devices capable of performing VxLAN encapsulation usually have only one
FDB table, unlike the software data path which has two - one in the
bridge driver and another in the VxLAN driver.
Therefore, bridge FDB entries pointing to a VxLAN device are only
offloaded if there is a corresponding entry in the VxLAN FDB.
Allow clearing the offload indication in case the corresponding entry
was deleted from the VxLAN FDB.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
put_device has taken the null pinter check into account. So it is
safe to remove the duplicated check before put_device.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gswip tag was missing in the dsa_tag_protocol_to_str() function, add it.
Fixes: 7969119293 ("net: dsa: Add Lantiq / Intel GSWIP tag support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This handles the tag added by the PMAC on the VRX200 SoC line.
The GSWIP uses internally a GSWIP special tag which is located after the
Ethernet header. The PMAC which connects the GSWIP to the CPU converts
this special tag used by the GSWIP into the PMAC special tag which is
added in front of the Ethernet header.
This was tested with GSWIP 2.1 found in the VRX200 SoCs, other GSWIP
versions use slightly different PMAC special tags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no way for user-space to know what a given DSA network device's
tagging protocol is. Expose this information through a dsa/tagging
attribute which reflects the tagging protocol currently in use.
This is helpful for configuration (e.g: none behaves dramatically
different wrt. bridges) as well as for packet capture tools when there
is not a proper Ethernet type available.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 52638f71fc ("dsa: Move gpio reset into switch driver")
moved the GPIO handling into the switch drivers but forgot
to remove the GPIO header includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90b73b77d0, list_head is no longer needed.
Now we just need to convert the list iteration to array
iteration for drivers.
Fixes: 90b73b77d0 ("net: sched: change action API to use array of pointers to actions")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a port to be able to use EEE, both the MAC and the PHY must
support EEE. A phy can be provided by both a phydev or phylink. Verify
at least one of these exist, not just phydev.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a DSA slave network device was previously disabled, there is no need
to suspend or resume it.
Fixes: 2446254915 ("net: dsa: allow switch drivers to implement suspend/resume hooks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We avoid 2 VLAs by using a pre-allocated field in dsa_switch. We also
try to avoid dynamic allocation whenever possible (when using fewer than
bits-per-long ports, which is the common case).
Link: http://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Link: http://lkml.kernel.org/r/20180505185145.GB32630@lunn.ch
Signed-off-by: Salvatore Mesoraca <s.mesoraca16@gmail.com>
[kees: tweak commit subject and message slightly]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the extact struct from a tc qdisc add to the block bind function and,
in turn, to the setup_tc ndo of binding device via the tc_block_offload
struct. Pass this back to any block callback registrations to allow
netlink logging of fails in the bind process.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pskb_trim_rcsum fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pskb_trim_rcsum.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch enables emitting VLAN notifications for the bridge CPU
port in addition to the existing slave port notifications. These
notifications have orig_dev set to the bridge in question.
Because there's no specific support for these VLANs, just ignore the
notifications to maintain the current behavior.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the attrs and allow to expose port flavour to user via devlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if commit 1d27732f41 ("net: dsa: setup and teardown ports") indicated
that registering a devlink instance for unused ports is not a problem, and this
is true, this can be confusing nonetheless, so let's not do it.
Fixes: 1d27732f41 ("net: dsa: setup and teardown ports")
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHYLINK within the DSA subsystem in order to support more
complex devices such as pluggable (SFP) and non-pluggable (SFF) modules, 10G
PHYs, and traditional PHYs. Using PHYLINK allows us to drop some amount of
complexity we had while probing fixed and non-fixed PHYs using Device Tree.
Because PHYLINK separates the Ethernet MAC/port configuration into different
stages, we let switch drivers implement those, and for now, we maintain
functionality by calling dsa_slave_adjust_link() during
phylink_mac_link_{up,down} which provides semantically equivalent steps.
Drivers willing to take advantage of PHYLINK should implement the phylink_mac_*
operations that DSA wraps.
We cannot quite remove the adjust_link() callback just yet, because a number of
drivers rely on that for configuring their "CPU" and "DSA" ports, this is done
dsa_port_setup_phy_of() and dsa_port_fixed_link_register_of() still.
Drivers that utilize fixed links for user-facing ports (e.g: bcm_sf2) will need
to implement phylink_mac_ops from now on to preserve functionality, since PHYLINK
*does not* create a phy_device instance for fixed links.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we use PHYLIB to manage the per-port link indication, this will
also be reflected correctly in the network device's carrier state, so we
can use ethtool_op_get_link() instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for PHYLINK within DSA, define a number of
operations that we will need and that switch drivers can start implementing.
Proper integration with PHYLINK will follow in subsequent patches.
We start selecting PHYLINK (which implies PHYLIB) in net/dsa/Kconfig
such that drivers can be guaranteed that this dependency is properly
taken care of and can start referencing PHYLINK helper functions without
requiring stubs or anything.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch enables sending notifications also for events on FDB
entries that weren't added by the user. Give the drivers the information
necessary to distinguish between the two origins of FDB entries.
To maintain the current behavior, have switchdev-implementing drivers
bail out on notifications about non-user-added FDB entries. In case of
mlxsw driver, allow a call to mlxsw_sp_span_respin() so that SPAN over
bridge catches up with the changed FDB.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the same type of ethtool diversion that we have for
ETH_SS_STATS and make it work with ETH_SS_PHY_STATS. This allows
providing PHY level statistics for CPU ports that are directly
connecting to a PHY device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having more call sites attempting to obtain a
reference against a PHY device corresponding to a particular port,
introduce a helper function for that purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we largely assumed that we were interested in ETH_SS_STATS
type of strings for all ethtool operations, this is about to change with
the introduction of additional string sets, e.g: ETH_SS_PHY_STATS.
Update all functions to take an appropriate stringset argument and act
on it when it is different than ETH_SS_STATS for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is completely redundant with what netdev_set_default_ethtool_ops()
does, we are always guaranteed to have a valid dev->ethtool_ops pointer,
however, within that structure, not all function calls may be populated,
so we still have to check them individually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell switches under some conditions will pass a frame to the
host with the port being the CPU port. Such frames are invalid, and
should be dropped. Not dropping them can result in a crash when
incrementing the receive statistics for an invalid port.
Reported-by: Chris Healy <cphealy@gmail.com>
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During the conversion to dsa_is_user_port(), a condition ended up being
reversed, which would prevent the creation of any user port when using
the legacy binding and/or platform data, fix that.
Fixes: 4a5b85ffe2 ("net: dsa: use dsa_is_user_port everywhere")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward the rx/tx timestamp machinery from the dsa infrastructure to the
switch driver.
On the rx side, defer delivery of skbs until we have an rx timestamp.
This mimicks the behavior of skb_defer_rx_timestamp.
On the tx side, identify PTP packets, clone them, and pass them to the
underlying switch driver before we transmit. This mimicks the behavior
of skb_tx_timestamp.
Adjusted txstamp API to keep the allocation and freeing of the clone
in the same central function by Richard Cochran
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to the dsa slave network device so that
switch drivers can implement the SIOC[GS]HWTSTAMP ioctls and the
ethtool timestamp-info interface.
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for enabling the internal PHY for a 'cpu' port.
It has been tested on GE B850v3, B650v3 and B450v3, which have a
built-in MV88E6240 switch hardwired to a PCIe based network card.
On these machines the internal PHY of the i210 network card and
the Marvell switch are connected to each other and must be enabled
for properly using the switch. While the i210 PHY will be enabled
when the network interface is enabled, the switch's port is not
exposed as network interface. Additionally the mv88e6xxx driver
resets the chip during probe, so the PHY is disabled without this
patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having the different master network device drivers
potentially used by DSA/Broadcom tags, move the padding necessary for
the switches to accept short packets where it makes most sense: within
tag_brcm.c. This avoids multiplying the number of similar commits to
e.g: bgmac, bcmsysport, etc.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to make the dsa_legacy_register() stub return 0 in order for
dsa_init_module() to successfully register and continue registering the
ETH_P_XDSA packet handler.
Fixes: 2a93c1a365 ("net: dsa: Allow compiling out legacy support")
Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to let MT7530 switch can recognize well those egress packets
having both special tag and VLAN tag, the information about the special
tag should be carried on the existing VLAN tag. On the other hand, it's
unnecessary for extra handling for ingress packets when VLAN tag is
present since it is able to put the VLAN tag after the special tag and
then follow the existing way to parse.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a configuration option: CONFIG_NET_DSA_LEGACY allowing to compile out
support for the old platform device and Device Tree binding registration.
Support for these configurations is scheduled to be removed in 4.17.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.
If we would support moving target netdev across netns, using
pointer would be better than ifindex.
This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA ports also need to have a dedicated CPU port assigned to them,
because they need to know where to egress frames targeting the CPU,
e.g. To_Cpu frames received on a Marvell Tag port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a MAC address is added to or removed from a switch port in the
fabric, the target switch must program its port and adjacent switches
must program their local DSA port used to reach the target switch.
For this purpose, use the dsa_towards_port() helper to identify the
local switch port which must be programmed.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings no functional changes.
It moves out the MDB code iterating on a multicast group into new
dsa_switch_mdb_{prepare,add}_bitmap() functions.
This gives us a better isolation of the two switchdev phases.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings no functional changes.
It moves out the VLAN code iterating on a list of VLAN members into new
dsa_switch_vlan_{prepare,add}_bitmap() functions.
This gives us a better isolation of the two switchdev phases.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch MDB ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from MDB prepare and add operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from VLAN prepare and add operations.
At the same time, fix the following checkpatch warning:
WARNING: line over 80 characters
#74: FILE: drivers/net/dsa/dsa_loop.c:177:
+ const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the refcount to 0 when allocating a tree to match the number of
switch devices it holds may cause an 'increment on 0; use-after-free',
if CONFIG_REFCOUNT_FULL is enabled.
To fix this, do not decrement the refcount of a newly allocated tree,
increment it when an already allocated tree is found, and decrement it
after the probing of a switch, as done with the previous behavior.
At the same time, make dsa_tree_get and dsa_tree_put accept a NULL
argument to simplify callers, and return the tree after incrementation,
as most kref users like of_node_get and of_node_put do.
Fixes: 8e5bf9759a ("net: dsa: simplify tree reference counting")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan9303 set bits in the host CPU tag indicating if a ingress frame
is a trapped IGMP or STP frame. Use these bits to calculate
skb->offload_fwd_mark more efficiently.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA now uses one of the symbols exported by the bridge,
br_vlan_enabled(). This has a stub, if the bridge is not
enabled. However, if the bridge is enabled, we cannot have DSA built
in and the bridge as a module, otherwise we get undefined symbols at
link time:
net/dsa/port.o: In function `dsa_port_vlan_add':
net/dsa/port.c:255: undefined reference to `br_vlan_enabled'
net/dsa/port.o: In function `dsa_port_vlan_del':
net/dsa/port.c:270: undefined reference to `br_vlan_enabled'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new type: DSA_TAG_PROTO_PREPEND which allows us to support for the
4-bytes Broadcom tag that we already support, but in a format where it
is pre-pended to the packet instead of located between the MAC SA and
the Ethertyper (DSA_TAG_PROTO_BRCM).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting the same Broadcom tag format, but instead
of inserted between the MAC SA and EtherType, prepended to the Ethernet
frame, restructure the code a little bit to make that possible and take
an offset parameter.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that IGMP packets no longer is flooded in HW, we want the SW bridge to
forward packets based on bridge configuration. To make that happen,
IGMP packets must have skb->offload_fwd_mark = 0.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The software bridge needs to know if a packet has already been bridged
by hardware offload to ports in the same hardware offload, in order
that it does not re-flood them, causing duplicates. This is
particularly true for broadcast and multicast traffic which the host
has requested.
By setting offload_fwd_mark in the skb the bridge will only flood to
ports in other offloads and other netifs. Set this flag in the DSA and
EDSA tag driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SWITCHDEV_ATTR_ID_PORT_PARENT_ID is used by the software bridge when
determining which ports to flood a packet out. If the packet
originated from a switch, it assumes the switch has already flooded
the packet out the switches ports, so the bridge should not flood the
packet itself out switch ports. Ports on the same switch are expected
to return the same parent ID when SWITCHDEV_ATTR_ID_PORT_PARENT_ID is
called.
DSA gets this wrong with clusters of switches. As far as the software
bridge is concerned, the cluster is all one switch. A packet from any
switch in the cluster can be assumed to have been flooded as needed
out of all ports of the cluster, not just the switch it originated
from. Hence all ports of a cluster should return the same parent. The
old implementation did not, each switch in the cluster had its own ID.
Also wrong was that the ID was not unique if multiple DSA instances
are in operation.
Use the tree ID as the parent ID, which is the same for all switches
in a cluster and unique across switch clusters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not return after successfully preparing the VLAN
addition on every ports member of a it. Fix this.
Fixes: 1ca4aa9cd4 ("net: dsa: check VLAN capability of every switch")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not return after successfully preparing the MDB
addition on every ports member of a multicast group. Fix this.
Fixes: a1a6b7ea7f ("net: dsa: add cross-chip multicast support")
Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The software bridge can be build with vlan filtering support
included. However, by default it is turned off. In its turned off
state, it still passes VLANs via switchev, even though they are not to
be used. Don't pass these VLANs to the hardware. Only do so when vlan
filtering is enabled.
This fixes at least one corner case. There are still issues in other
corners, such as when vlan_filtering is later enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the host indicates when a multicast group should be forwarded
from the switch to the host, don't do it by default.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notify mechanism does not need to modify the port it is notifying.
So make the parameter const.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to handle switchdev host mdb add/del. Since DSA uses one of
the switch ports as a transport to the host, we just need to add an
MDB on this port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit brings no functional changes. It gets rid of the underscore
prefixed _dsa_register_switch and _dsa_unregister_switch functions in
favor of dsa_switch_probe() which parses and adds a switch to a tree and
dsa_switch_remove() which removes a switch from a tree.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the tree setup is centralized, we can simplify the code a bit
more by setting up or tearing down the tree directly when adding or
removing a switch to/from it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *_complete() functions take too much arguments to do only one thing:
they try to fetch the dsa_port structures corresponding to device nodes
under the "link" list property of DSA ports, and use them to setup the
routing table of switches.
This patch simplifies them by providing instead simpler
dsa_{port,switch,tree}_setup_routing_table functions which return a
boolean value, true if the tree is complete.
dsa_tree_setup_routing_table is called inside dsa_tree_setup which
simplifies the switch registering function as well.
A switch's routing table is now initialized before its setup.
This also makes dsa_port_is_valid obsolete, remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The OF code provides a of_for_each_phandle() helper to iterate over
phandles. Use it instead of arbitrary iterating ourselves over the list
of phandles hanging to the "link" property of the port's device node.
The of_phandle_iterator_next() helper calls of_node_put() itself on
it.node. Thus We must only do it ourselves if we break the loop.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having two dsa_ds_find_port_dn (which returns a bool) and
dsa_dst_find_port_dn (which returns a switch) functions, provide a more
explicit dsa_tree_find_port_by_node function which returns a matching
port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_dsa_port_apply and dsa_cpu_port_apply functions do exactly the
same. The dsa_user_port_apply function does not try to register a fixed
link but try to create a slave.
This commit factorizes and scopes all that in two convenient
dsa_port_setup and dsa_port_teardown functions.
It won't hurt to register a devlink_port for unused port as well.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches brings no functional changes. It removes the unused dst
argument from the dsa_ds_apply and dsa_ds_unapply functions, rename them
to dsa_switch_setup and dsa_switch_teardown for a more explicit scope.
This clarifies the steps of the setup or teardown of a switch fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit provides better scope for the DSA tree setup and teardown
functions. It renames the "applied" bool to "setup" and print a message
when the tree is setup, as it is done during teardown.
At the same time, check dst->setup in dsa_tree_setup, where it is set to
true.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DSA helpers to setup and teardown a master net device wired to its
CPU port. This centralizes the dsa_ptr assignment.
This also makes the master ethtool helpers static at the same time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_dst_parse function called just before dsa_dst_apply does not
parse the tree but does only one thing: it assigns the default CPU port
to dst->cpu_dp and to each user ports.
This patch simplifies this by calling a dsa_tree_setup_default_cpu
function at the beginning of dsa_dst_apply directly.
A dsa_port_is_user helper is added for convenience.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA port has a dedicated CPU port assigned to it, stored in the cpu_dp
member. It is not meant to be modified by a port, thus make it const.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove scripts/checkpatch.pl CHECKs by adjusting indenting.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the dsa_port_parse_cpu() function to resolve the tagging protocol
at port parsing time, instead of waiting for the whole tree to be
complete.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dsa_port_parse_user, dsa_port_parse_dsa and dsa_port_parse_cpu
functions to factorize the code shared by both OF and pdata parsing.
They don't do much for the moment but will be extended later to support
tagging protocol resolution for example.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing a port, simply use of_property_read_bool which checks the
presence of a given property, instead of parsing the link phandle.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing a switch, we have to identify to which tree it belongs and
parse its ports. Provide two functions to separate the OF and platform
data specific paths.
Also use the of_property_read_variable_u32_array function to parse the
OF member array instead of calling of_property_read_u32_index twice.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will need a reference to the dsa_switch_tree when parsing a CPU port,
so fetch it right after parsing the member and before parsing ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unnecessary index argument from the
dsa_dst_add_ds and dsa_dst_del_ds functions and renames them to
dsa_tree_add_switch and dsa_tree_remove_switch respectively.
In addition to a more explicit scope, we now check the presence of an
existing switch with the same index directly within dsa_tree_add_switch.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename dsa_get_dst to dsa_tree_find since it doesn't increment the
reference counter, rename dsa_add_dst to dsa_tree_alloc for symmetry
with dsa_tree_free, and provide a convenient dsa_tree_touch function to
find or allocate a new tree.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide convenient dsa_tree_get and dsa_tree_put functions scoping a DSA
tree used to increment and decrement its reference counter, instead of
poking directly its kref structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA trees have a refcount used to automatically free the dsa_switch_tree
structure once there is no switch devices inside of it.
The refcount is incremented when a switch is added to the tree, and
decremented when it is removed from it.
But because of kref_init, the refcount is also incremented at
initialization, and when looking up the tree from the list for symmetry.
Thus the current code stores the number of switches plus one, and makes
the switch registration more complex.
To simplify the switch registration function, we reset the refcount to
zero after initialization and don't increment it when looking up a tree.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to a DSA switch and port, rename the tree index from "tree" to
"index" and make it an unsigned int because it isn't supposed to be less
than 0.
u32 is an OF specific data used to retrieve the value and has no need to
be propagated up to the tree index.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip flood broadcast and unknown multicast frames.
On receive set skb->offload_fwd_mark to prevent the SW from flooding to the
same ports.
One exception: Because the ALR is set up to forward STP BPDUs only to CPU,
the SW bridge should flood STP BPDUs if local STP is not enabled.
This is archived by not setting skb->offload_fwd_mark on STP BPDUs.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.
Add an ALR entry with STP state override to fix that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_xmit_use_arl() introduced in previous patch set is wrong.
The chip flood broadcast and unknown multicast frames. The effect is that
broadcasts and multicasts are duplicated on egress. It is not possible to
configure the chip to direct unknown multicasts to CPU port only.
This means that only unicast frames can be transmitted using ALR lookup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that slave dsa_port always have their name set, there is no need to
pass it to dsa_slave_create() anymore. Remove this argument.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the optional "label" property and assign a default one directly at
parse time instead of doing it when creating the slave.
For legacy, simply assign the port name stored in cd->port_names.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetching the master device can be done directly when a port is parsed
from device tree or pdata, instead of waiting until dsa_dst_parse.
Now that -EPROBE_DEFER is returned before we add the switch to the tree,
there is no need to check for this error after dsa_dst_parse.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign a port's type at parsed time instead of waiting for the tree to
be completed.
Because this is now done earlier, we can use the port's type in
dsa_port_is_* helpers instead of digging again in topology description.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add symmetrical DSA port parsing functions for pdata and device tree,
used to parse and validate a given port node or platform data.
They don't do much for the moment but will be extended later on to
assign a port type and get device references.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point into hiding the -EINVAL error code in ERR_PTR from a
dsa_get_ports function, simply get the "ports" node directly from within
the dsa_parse_ports_dn function.
This also has the effect to make the pdata and device tree handling code
symmetrical inside _dsa_register_switch.
At the same time, rename dsa_parse_ports_dn to dsa_parse_ports_of
because _of is a more common suffix for device tree parsing functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
The new bindings (dsa2.c) and the old bindings (legacy.c) share two
helpers dsa_cpu_dsa_setup and dsa_cpu_dsa_destroy, used to register or
deregister a fixed PHY if a given port has a corresponding device node.
Unclutter the code by moving them into two new port.c helpers,
dsa_port_fixed_link_register_of and dsa_port_fixed_link_(un)register_of.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA core provides port types, there is no need to keep this
information at the switch level. This is a static information that is
part of a DSA core dsa_port structure. Remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an enumerated type for ports, which will be way more explicit
to identify a port type instead of digging into switch port masks.
A port can be of type CPU, DSA, user, or unused by default. This is a
static parsed information that cannot be changed at runtime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the DSA code still check ds->enabled_port_mask directly to
inspect a given port type instead of using the provided dsa_is_user_port
helper. Change this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CPU transmit directly to port using tag, the LAN9303 does not
learn MAC addresses received on the CPU port into the ALR.
ALR learning is performed only when transmitting using ALR lookup.
Solution:
If the two external ports are bridged and the packet is not STP BPDU,
then use ALR lookup to allow ALR learning on CPU port.
Otherwise transmit directly to port with STP state override.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the code that tried to identify if a PHY designated by Device
Tree required diversion through the DSA-created MDIO bus. This was
created mainly for the bcm_sf2.c driver back when it did not have its
own MDIO bus driver, which it now has since 461cd1b03e ("net: dsa:
bcm_sf2: Register our slave MDIO bus").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Martin Hundebøll <mnhu@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unapply functions are called on the error path.
As for dsa_port_mask, enabled_port_mask and cpu_port_mask won't be used
after so there's no need to unmask the corresponding port bit from them.
This makes dsa_cpu_port_unapply() and dsa_dsa_port_unapply() identical,
which can be factorized later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy code does not unmask the cpu_port_mask and dsa_port_mask as
stated. But this is done on the error path and those masks won't be used
after that. So instead of fixing the bit operation, simply remove it.
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of pdata, the dsa_cpu_parse function calls dev_put() before
making sure it isn't NULL. Fix this.
Fixes: 71e0bbde0d ("net: dsa: Add support for platform data")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers are converted to use block callbacks for TC_SETUP_CLS*.
So it is now safe to remove the calls to ndo_setup_tc from cls_*
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the newly introduced block callback infrastructure and
convert ndo_setup_tc calls for matchall offloads to block callbacks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure has a "netdev" member, which can be used for
either the master device, or the slave device, depending on its type.
It is true that today, CPU port are not exposed to userspace, thus the
port's netdev member can be used to point to its master interface.
But it is still slightly confusing, so split it into more explicit
"master" and "slave" members inside an anonymous union.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_master_get_slave is slightly confusing since the idiomatic "get"
term often suggests reference counting, in symmetry to "put".
Rename it to dsa_master_find_slave to make the look up operation clear.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many part of the DSA slave code require to get the master device
assigned to a slave device. Remove dsa_master_netdev() in favor of a
dsa_slave_to_master() helper which does that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many portions of DSA core code require to get the dsa_port structure
corresponding to a slave net_device. For this purpose, introduce a
dsa_slave_to_port() helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both DSA slave create and destroy functions call call_dsa_notifiers with
respectively DSA_PORT_REGISTER and DSA_PORT_UNREGISTER and the same
dsa_notifier_register_info structure.
Wrap this in a dsa_slave_notify helper so prevent cluttering these
functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dsa_slave_create is called, the related port already has a CPU port
assigned to it, available in its cpu_dp member. Use it instead of the
unique tree cpu_dp.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is no user for the .set_addr function, remove it from
DSA. If a switch supports this feature (like mv88e6xxx), the
implementation can be done in the driver setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to tell the DSA master network device doing the actual
transmission what the desired switch port and queue number is for it to
resolve that to the internal transmit queue it is mapped to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for communicating a given DSA network device's port
number and switch index, create a specialized DSA notifier and two
events: DSA_PORT_REGISTER and DSA_PORT_UNREGISTER that communicate: the
slave network device (slave_dev), port number and switch number in the
tree.
This will be later used for network device drivers like bcmsysport which
needs to cooperate with its DSA network devices to set-up queue mapping
and scheduling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_ptr is a dsa_port instance, there is no need to keep
the tag operations in the dsa_switch_tree structure. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With DSA, a master net device (CPU facing interface) has a dsa_ptr
pointer to which hangs a dsa_switch_tree. This is not correct because a
master interface is wired to a dedicated switch port, and because we can
theoretically have several master interfaces pointing to several CPU
ports of the same switch fabric.
Change the master interface's dsa_ptr for the CPU dsa_port pointer.
This is a step towards supporting multiple CPU ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to make DSA master devices point to their corresponding
CPU port instead of the whole tree, add copies of dst and rcv in the
dsa_port structure so that we keep fast access in the receive hot path.
Also keep the copies at the beginning of the dsa_port structure in order
to ensure they are available in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA tagging protocol operations are specific to each CPU port,
thus the dsa_device_ops pointer belongs to the dsa_port structure.
>From now on assign a slave's xmit copy from its CPU port tagging
operations. This will ease the future support for multiple CPU ports.
Also keep the tag_ops at the beginning of the dsa_port structure so that
we ensure copies for hot path are in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resolving the DSA tagging protocol used by a CPU switch, use a
temporary "tag_ops" variable to store the dsa_device_ops instead of
using directly dst->tag_ops. This will make the future patches moving
this pointer around easier to read.
There is no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that the master device is linked to a CPU port by using
"cpu_dp" for the dsa_port variable in master.c instead of "port", then
use a "port" variable to describe the port index, as usually seen in
other places of DSA core.
This will make the future patch touching dsa_ptr more readable. There is
no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA tagging code does not need to know about the DSA architecture,
it only needs to return the slave device corresponding to the source
port index (and eventually the source device index for cascade-capable
switches) parsed from the frame received on the master device.
For this purpose, provide an inline dsa_master_get_slave helper which
validates the device and port indexes and look up the slave device.
This makes the tagging rcv functions more concise and robust, and also
makes dsa_get_cpu_port obsolete.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot be registering the network device first, then setting its
carrier off and finally connecting it to a PHY, doing that leaves a
window during which the carrier is at best inconsistent, and at worse
the device is not usable without a down/up sequence since the network
device is visible to user space with possibly no PHY device attached.
Re-order steps so that they make logical sense. This fixes some devices
where the port was not usable after e.g: an unbind then bind of the
driver.
Fixes: 0071f56e46 ("dsa: Register netdev before phy")
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_nway_reset now that dsa_slave_nway_reset does exactly
the same.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_set_link_ksettings now that dsa_slave_set_link_ksettings
does exactly the same.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_get_link_ksettings now that dsa_slave_get_link_ksettings
does exactly the same.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to store a phy_device in dsa_slave_priv since
net_device already provides one. Simply s/p->phy/dev->phydev/.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of returning -EOPNOTSUPP when a slave device has no PHY,
directly return -ENODEV as ethtool and phylib do.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide dsa_port_enable and dsa_port_disable helpers to respectively
enable and disable a switch port. This makes the dsa_port_set_state_now
helper static.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA slave open function configures the unicast MAC addresses on the
master device, enable the switch port, change its STP state, then start
the PHY device.
Make the close function symmetric, by first stopping the PHY device,
then changing the STP state, disabling the switch port and restore the
master device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping a DSA port's FDB entries is not specific to a DSA slave, so add
a dsa_port_fdb_dump function, similarly to dsa_port_fdb_add and
dsa_port_fdb_del.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few DSA slave functions take a dsa_slave_priv pointer as first
argument, whereas the scope of the slave.c functions is the slave
net_device structure. Fix this and rename dsa_netpoll_send_skb to
dsa_slave_netpoll_send_skb.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of open coding the check.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA overrides the master device ethtool ops, so that it can inject stats
from its dedicated switch CPU port as well.
The related code is currently split in dsa.c and slave.c, but it only
scopes the master net device. Move it to a new master.c DSA core file.
This file will be later extented with master net device specific code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA overrides the master's ethtool ops so that we can inject its CPU
port's statistics. Because of that, we need to setup the ethtool ops
after the master's dsa_ptr pointer has been assigned, not before.
This patch setups the ethtool ops after dsa_ptr is assigned, and
restores them before it gets cleared.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch tree is meant to be applied, it already has a CPU
port. Thus remove the condition of dst->cpu_dp.
Moreover, the next lines access dst->cpu_dp unconditionally.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to store a copy of the master ethtool ops, storing the
original pointer in DSA and the new one in the master netdev itself is
enough.
In the meantime, set orig_ethtool_ops to NULL when restoring the master
ethtool ops and check the presence of the master original ethtool ops as
well as its needed functions before calling them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We originally used skb->priority but that was not quite correct as this
bitfield needs to contain the egress switch queue we intend to send this
SKB to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let switch drivers indicate how many TX queues they support. Some
switches, such as Broadcom Starfighter 2 are designed with 8 egress
queues. Future changes will allow us to leverage the queue mapping and
direct the transmission towards a particular queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two kfree_skb() should be consume_skb(), to be friend with drop monitor
(perf record ... -e skb:kfree_skb)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first call of skb_put_padto() will free up the SKB on error, but we
return NULL which tells dsa_slave_xmit() that the original SKB should be
freed so this would lead to a double free here.
The second skb_put_padto() already frees the passed sk_buff reference
upon error, so calling kfree_skb() on it again is not necessary.
Detected by CoverityScan, CID#1416687 ("USE_AFTER_FREE")
Fixes: e71cb9e009 ("net: dsa: ksz: fix skb freeing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile tested only, but saw no warnings/errors with
allmodconfig build.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer frees the original skb when an xmit function returns NULL,
meaning an error occurred. But if the tagging code copied the original
skb, it is responsible of freeing the copy if an error occurs.
The ksz tagging code currently has two issues: if skb_put_padto fails,
the skb copy is not freed, and the original skb will be freed twice.
To fix that, move skb_put_padto inside both branches of the skb_tailroom
condition, before freeing the original skb, and free the copy on error.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking handle, which does not have the inner class
information and drivers wrongly assume clsact->egress as ingress, use
the newly introduced classid identification helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7530 inserts the 4 magic header in between the 802.3 address and
protocol field. The patch implements the callback that can be called by
the flow dissector to figure out the real protocol and offset of the
network header. With this patch applied we can properly parse the packet
and thus make hashing function properly.
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to access this struct from within the flow_dissector to fix
dissection for packets coming in on DSA devices.
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save 2628 bytes on arm eabi by allocate only the required 3 ports.
Now that ds->num_ports is correct: In net/dsa/tag_lan9303.c
eliminate duplicate LAN9303_MAX_PORTS, use ds->num_ports.
(Matching the pattern of other net/dsa/tag_xxx.c files.)
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From all switchdev devices only DSA requires special FDB dump. This is due
to lack of ability for syncing the hardware learned FDBs with the bridge.
Due to this it is removed from switchdev and moved inside DSA.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the MDB HW database is synced with the bridge's one, thus,
There is no need to support special dump functionality.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge port attributes/vlan for DSA devices should be set only
from bridge code. Furthermore, The vlans are synced totally with the
bridge so there is no need for special dump support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA drivers do not support bridge flags offload. Yet, this attribute
should be added in order for the bridge to fail when one tries set a
flag on the port, as explained in commit dc0ecabd62 ("net: switchdev:
Add support for querying supported bridge flags by hardware").
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA uses switchdev's implementation of FDB add/del ndos. This
patch moves the implementation inside DSA in order to support the legacy
way for static FDB configuration.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for learning FDB through notification. The driver defers
the hardware update via ordered work queue. In case of a successful
FDB add a notification is sent back to bridge.
In case of hw FDB del failure the static FDB will be deleted from
the bridge, thus, the interface is moved to down state in order to
indicate inconsistent situation.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the switchdev objects are embedded inside the DSA notifier
info. This patch removes this dependency. This is done as a preparation
stage before adding support for learning FDB through the switchdev
notification chain.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.
The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support FDB add/del to be on a notifier chain the slave
API need to be changed to be switchdev independent.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_create currently takes 4 arguments while it only needs the
related dsa_port and its name. Remove all other arguments.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_cpu_dsa_setup currently takes 4 arguments but they are all available
from the dsa_port argument. Remove all others.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_switch_alloc() already assigns ds-dev, which can be used in
dsa_switch_setup_one and dsa_cpu_dsa_setups instead of requiring an
additional struct device argument.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let dsa_slave_setup_tc be a splitter for specific setup_tc types and
push out cls_matchall specific code into a separate function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be aligned with the rest of the types, rename
TC_SETUP_MATCHALL to TC_SETUP_CLSMATCHALL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During testing with a background iperf pushing 1Gbit/sec worth of
traffic and having both ifconfig and ethtool collect statistics, we
could see quite frequent deadlocks. Convert the often accessed DSA slave
network devices statistics to per-cpu 64-bit statistics to remove these
deadlocks and provide fast efficient statistics updates.
Fixes: f613ed665b ("net: dsa: Add support for 64-bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rest of the helpers are named tcf_exts_*, so change the name of
the action number helpers to be aligned. While at it, change to inline
functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA slave network devices maintain a pair of bytes and packets counters
for each directions, but these are not 64-bit capable. Re-use
pcpu_sw_netstats which contains exactly what we need for that purpose
and update the code path to report 64-bit capable statistics.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid confusion with the PHY EEE settings, rename the .set_eee and
.get_eee ops to respectively .set_mac_eee and .get_mac_eee.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch operations for EEE are only meant to configure a port's
MAC EEE settings. The port's PHY EEE settings are accessed by the DSA
layer and must be made available via a proper PHY driver.
In order to reduce this confusion, remove the phy_device argument from
the .set_eee operation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA drivers are calling phy_init_eee if eee_enabled is true.
Move up this statement in the DSA layer to simplify the DSA drivers.
qca8k does not require to cache the ethtool_eee structures from now on.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port's PHY and MAC are both implied in EEE. The current code does
not call the PHY operations if the related device is NULL. Change that
by returning -ENODEV if there's no PHY device attached to the interface.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
The mt7530 driver has its dsa_switch_ops::get_tag_protocol function
check ds->cpu_port_mask to issue a warning in case the configured CPU
port is not capable of supporting tags.
After commit 14be36c2c9 ("net: dsa: Initialize all CPU and enabled
ports masks in dsa_ds_parse()") we slightly re-arranged the
initialization such that this was no longer working. Just make sure that
ds->cpu_port_mask is set prior to the first call to get_tag_protocol,
thus restoring the expected contract. In case of error, the CPU port bit
is cleared.
Fixes: 14be36c2c9 ("net: dsa: Initialize all CPU and enabled ports masks in dsa_ds_parse()")
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_is_port_initialized helper is only used by dsa_switch_resume and
dsa_switch_suspend, if CONFIG_PM_SLEEP is enabled. Make it static to
dsa.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 6d3c8c0dd8 ("net: dsa: Remove master_netdev and
use dst->cpu_dp->netdev") and a29342e739 ("net: dsa: Associate
slave network device with CPU port") we would be seeing NULL pointer
dereferences when accessing dst->cpu_dp->netdev too early. In the legacy
code, we actually know early in advance the master network device, so
pass it down to the relevant functions.
Fixes: 6d3c8c0dd8 ("net: dsa: Remove master_netdev and use dst->cpu_dp->netdev")
Fixes: a29342e739 ("net: dsa: Associate slave network device with CPU port")
Reported-by: Jason Cobham <jcobham@questertangent.com>
Tested-by: Jason Cobham <jcobham@questertangent.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to how cross-chip VLAN works, define a bitmap of multicast
group members for a switch, now including its DSA ports, so that
multicast traffic can be sent to all switches of the fabric.
A switch may drop the frames if no user port is a member.
This brings support for multicast in a multi-chip environment.
As of now, all switches of the fabric must support the multicast
operations in order to program a single fabric port.
Reported-by: Jason Cobham <jcobham@questertangent.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Jason Cobham <jcobham@questertangent.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code only assigns the default cpu_dp to all user ports of
the switch to which the CPU port belongs. The user ports of the other
switches of the fabric thus don't have a default CPU port.
This patch fixes this by assigning the cpu_dp of all user ports of all
switches of the fabric when the tree is fully parsed.
Fixes: a29342e739 ("net: dsa: Associate slave network device with CPU port")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper function which will return a reference to the CPU
port used in a dsa_switch_tree. Right now this is a singleton, but this
will change once we introduce multi-CPU port support, so ease the
transition by converting the affected code paths.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple CPU ports with DSA, have the
dsa_port structure know which CPU it is associated with. This will be
important in order to make sure the correct CPU is used for transmission
of the frames. If not for functional reasons, for performance (e.g: load
balancing) and forwarding decisions.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate master_ethtool_ops and master_orig_ethtool_ops into struct
dsa_port in order to be both consistent, and make things self contained
within the dsa_port structure.
This is a preliminary change to supporting multiple CPU port interfaces.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple CPU ports, remove
dst->master_netdev and ds->master_netdev and replace them with only one
instance of the common object we have for a port: struct
dsa_port::netdev. ds->master_netdev is currently write only and would be
helpful in the case where we have two switches, both with CPU ports, and
also connected within each other, which the multi-CPU port patch series
would address.
While at it, introduce a helper function used in net/dsa/slave.c to
immediately get a reference on the master network device called
dsa_master_netdev().
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a multi-chip switch fabric, it is currently the responsibility of the
driver to add the CPU or DSA (interconnecting chips together) ports as
members of a new VLAN entry. This makes the drivers more complicated.
We want the DSA drivers to be stupid and the DSA core being the one
responsible for caring about the abstracted switch logic and topology.
Make the DSA core program the CPU and DSA ports as part of the VLAN.
This makes all chips of the data path to be aware of VIDs spanning the
the whole fabric and thus, seamlessly add support for cross-chip VLAN.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the VLAN object is propagated to every switch chip of the
switch fabric, we can easily ensure that they all support the required
VLAN operations before modifying an entry on a single switch.
To achieve that, remove the condition skipping other target switches,
and add a bitmap of VLAN members, eventually containing the target port,
if we are programming the switch target.
This will allow us to easily add other VLAN members, such as the DSA or
CPU ports (to introduce cross-chip VLAN support) or the other port
members if we want to reduce hardware accesses later.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9520ed8fb8 ("net: dsa: use cpu_switch instead of ds[0]")
replaced the use of dst->ds[0] with dst->cpu_switch since that is
functionally equivalent, however, we can now run into an use after free
scenario after unbinding then rebinding the switch driver.
The use after free happens because we do correctly initialize
dst->cpu_switch the first time we probe in dsa_cpu_parse(), then we
unbind the driver: dsa_dst_unapply() is called, and we rebind again.
dst->cpu_switch now points to a freed "ds" structure, and so when we
finally dereference it in dsa_cpu_port_ethtool_setup(), we oops.
To fix this, simply set dst->cpu_switch to NULL in dsa_dst_unapply()
which guarantees that we always correctly re-assign dst->cpu_switch in
dsa_cpu_parse().
Fixes: 9520ed8fb8 ("net: dsa: use cpu_switch instead of ds[0]")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was no reason for duplicating the code that initializes
ds->enabled_port_mask in both dsa_parse_ports_dn() and
dsa_parse_ports(), instead move this to dsa_ds_parse() which is early
enough before ops->setup() has run.
While at it, we can now make dsa_is_cpu_port() check ds->cpu_port_mask
which is a step towards being multi-CPU port capable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have all the information we need in dsa_port, so use it instead of
repeating the same arguments over and over again.
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need to have a reference to a dsa_switch, instead we should
pass a reference to a CPU dsa_port, change that. This is a preliminary
change to better support multiple CPU ports.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_switch_suspend() and dsa_switch_resume() are functions that belong in
net/dsa/dsa.c and are not part of the legacy platform support code.
Fixes: a6a71f19fe ("net: dsa: isolate legacy code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of a86d8becc3 ("net: dsa: Factor bottom tag receive functions"),
the rcv caller frees the original SKB in case or error.
Be symmetric with that and make the xmit caller do the same.
At the same time, fix the checkpatch NULL comparison check:
CHECK: Comparison to NULL could be written "!nskb"
#208: FILE: net/dsa/tag_trailer.c:35:
+ if (nskb == NULL)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many rcv functions from net/dsa/tag_*.c have a useless out_drop goto
label which simply returns NULL. Kill it in favor of the obvious.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_ptr is not a void pointer anymore since Nov 2011, as of cf50dcc24f
("dsa: Change dsa_uses_{dsa, trailer}_tags() into inline functions"),
but an explicit dsa_switch_tree pointer, thus remove the (void *) cast.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer uses inline helpers and copy of the tagging functions for
faster access in hot path. Add comments to detail that.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
function ksz_rcv can be made static as it does not need to be
in global scope. Reformat arguments to make it checkpatch warning
free too.
Cleans up sparse warning: "symbol 'ksz_rcv' was not declared. Should
it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for the Microchip KSZ switch family tail tagging.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current dsa_register_switch function takes a useless struct device
pointer argument, which always equals ds->dev.
Drivers either call it with ds->dev, or with the same device pointer
passed to dsa_switch_alloc, which ends up being assigned to ds->dev.
This patch removes the second argument of the dsa_register_switch and
_dsa_register_switch functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper is only used once and makes the code more complicated that it
should. Remove it and reorganize the variables so that it fits on 80
columns.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the switchdev bridge ageing time attribute is propagated to all
switch chips of the fabric, each switch can check if the requested value
is valid and program itself, so that the whole fabric shares a common
ageing time setting.
This is especially needed for switch chips in between others, containing
no bridge port members but evidently used in the data path.
To achieve that, remove the condition which skips the other switches. We
also don't need to identify the target switch anymore, thus remove the
sw_index member of the dsa_notifier_ageing_time_info notifier structure.
On ZII Dev Rev B (with two 88E6352 and one 88E6185) and ZII Dev Rev C
(with two 88E6390X), we have the following hardware configuration:
# ip link add name br0 type bridge
# ip link set master br0 dev lan6
br0: port 1(lan6) entered blocking state
br0: port 1(lan6) entered disabled state
# echo 2000 > /sys/class/net/br0/bridge/ageing_time
Before this patch:
zii-rev-b# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
300000
300000
15000
zii-rev-c# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
300000
18750
After this patch:
zii-rev-b# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
15000
15000
15000
zii-rev-c# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
18750
18750
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new DSA_NOTIFIER_VLAN_ADD and DSA_NOTIFIER_VLAN_DEL events to
notify not only a single switch, but all switches of a the fabric when
an VLAN entry is added or removed.
For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new DSA_NOTIFIER_MDB_ADD and DSA_NOTIFIER_MDB_DEL events to
notify not only a single switch, but all switches of a the fabric when
an MDB entry is added or removed.
For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new DSA_NOTIFIER_FDB_ADD and DSA_NOTIFIER_FDB_DEL events to
notify not only a single switch, but all switches of a the fabric when
an FDB entry is added or removed.
For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch keeps the port-wide ageing time handling code in
dsa_port_ageing_time, pushes the requested ageing time value in a new
switch fabric notification, and moves the switch-wide ageing time
handling code in dsa_switch_ageing_time.
This has the effect that now not only the switch that the target port
belongs to can be programmed, but all switches composing the switch
fabric. For the moment, keep the current behavior and ignore other
switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA notifier events and info structure definitions are not meant for
DSA drivers and users, but only used internally by the DSA core files.
Move them from the public net/dsa.h file to the private dsa_priv.h file.
Also use this opportunity to turn the events into an anonymous enum,
because we don't care about the values, and this will prevent future
conflicts when adding (and sorting) new events.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which handles VLAN objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which handles MDB objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which handles FDB objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which sets a port ageing time in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which sets VLAN filtering on a port in port.c,
where it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which bridges a port in port.c, where it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new port.c file to hold all DSA port-wide logic. This patch moves
in the code which sets a port state.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev bridge ageing time attribute setter
from the DSA slave device to the generic DSA port, so that the future
port-wide API can also be used for other port types, such as CPU and DSA
links.
Also ds->ports is now a contiguous array of dsa_port structures, thus
their addresses cannot be NULL. Remove the useless check in
dsa_fastest_ageing_time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev VLAN filtering attribute setter from
the DSA slave device to the generic DSA port, so that the future
port-wide API can also be used for other port types, such as CPU and DSA
links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev VLAN object handlers from the DSA
slave device to the generic DSA port, so that the future port-wide API
can also be used for other port types, such as CPU and DSA links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev MDB object handlers from the DSA slave
device to the generic DSA port, so that the future port-wide API can
also be used for other port types, such as CPU and DSA links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev FDB object handlers from the DSA slave
device to the generic DSA port, so that the future port-wide API can
also be used for other port types, such as CPU and DSA links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the bridge join and leave functions only deal with a DSA port,
change their scope from the DSA slave net_device to the DSA generic
dsa_port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the fabric notification helper from the DSA slave to
the DSA port, since this is a DSA layer specific notion, that can be
used by non-slave ports (CPU and DSA).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having multiple STP state helpers scoping a slave device
supporting both the DSA logic and the switchdev binding, provide a
single dsa_port_set_state helper scoping a DSA port, as well as its
dsa_port_set_state_now wrapper which skips the prepare phase.
This allows us to better separate the DSA logic from the slave device
handling.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
