Apparently, some APs are buggy enough to send a zeroed
WMM IE. Don't WARN on this since this is not caused by a bug
on the client's system.
This aligns the condition of the WARNING in drv_conf_tx
with the validity check in ieee80211_sta_wmm_params.
We will now pick the default values whenever we get
a zeroed WMM IE.
This has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=199161
Fixes: f409079bb6 ("mac80211: sanity check CW_min/CW_max towards driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If userspace requested control port frames to go over 80211, then do so.
The control packets are intercepted just prior to delivery of the packet
to the underlying network device.
Pre-authentication type frames (protocol: 0x88c7) are also forwarded
over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We already have 'ifmgd' here, and it's already assigned
to the same value, so remove the duplicate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the current implementation, mac80211 advertises the support of
AP_VLANs based on the driver's support for AP mode; it also
blocks encrypted AP_VLAN operation on devices advertising
SW_CRYPTO_CONTROL.
The implementation seems weird in it's current form and could be
often confusing, this is because there can be drivers advertising
both SW_CRYPTO_CONTROL and AP mode support (ex: ath10k) in which case
AP_VLAN will still be supported but only in open BSS and not in
secured BSS.
When SW_CRYPTO_CONTROL is enabled, it makes more sense if the decision
to support AP_VLANs is left to the driver. Mac80211 can then allow
AP_VLAN operations depending on the driver support.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI has recently added new requirements that restrict the WMM
parameter values for 5GHz frequencies. We need to take care of the
following scenarios in order to comply with these new requirements:
1. When using mac80211 default values;
2. When the userspace tries to configure its own values;
3. When associating to an AP which advertises WWM IE.
When associating to an AP, the client uses the values in the
advertised WMM IE. But the AP may not comply with the new ETSI
requirements, so the client needs to check the current regulatory
rules and use those limits accordingly.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bandwidth change value reported via nl80211 contains mac80211
specific enum value(ieee80211_sta_rx_bw) and which is not
understand by userspace application. Map the mac80211 specific
value to nl80211_chan_width enum value to avoid using wrong value
in the userspace application. And used station's ht/vht capability
to map IEEE80211_STA_RX_BW_20 and IEEE80211_STA_RX_BW_160 with
proper nl80211 value.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SMPS_MODE change value notified via nl80211 contains mac80211
specific value(ieee80211_smps_mode) and user space application
will not know those values. This patch add support to map
the mac80211 enum value to nl80211_smps_mode which will be
understood by the userspace application.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With drivers implementing rate control in driver or firmware
rate_control_send_low() may not get called, and thus the
driver needs to know about changes in the multicast rate.
Add and use a new BSS change flag for this.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the low-level driver returns an invalid RSSI indication,
set the signal value to 0 as an indication to the upper layer.
Also, skip average level computation if signal is invalid.
Signed-off-by: Jean Pierre TOSONI <jp.tosoni@acksys.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing") added an
argument qos_ok to ieee80211_nullfunc_get to support QoS NDP. Despite
the claim in the commit log "Change all the drivers to *not* allow
QoS NDP for now, even though it looks like most of them should be OK
with that", this commit enables QoS NDP in response to beacons (see
change to mlme.c:ieee80211_send_nullfunc), causing ath9k_htc to lose
IP connectivity. See:
https://patchwork.kernel.org/patch/10241109/https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=891060
Introduce a hardware flag to allow such buggy drivers to override the
correct default behaviour of mac80211 of sending QoS NDP packets.
Signed-off-by: Ben Caradoc-Davies <ben@transient.nz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
skb_copy_expand without __GFP_NOWARN already does a dump_stack
on OOM so these messages are redundant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only works if the IV was stripped from packets. Create a smaller
variant of ieee80211_rx_h_amsdu, which bypasses checks already done
within the fast-rx context.
In order to do so, update cfg80211's ieee80211_data_to_8023_exthdr()
to take the offset between header and snap.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As there is no support for updating an existing ADDBA session with
a peer, we decline the request (while keeping the session active).
However, in case that the timeout did not change, there is no need
to decline the request, so modify the code to reply with status success
in such a case (this is useful for interoperability with APs that send an
ADDBA request update without changing the timeout value).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When powersave is disabled for the interface, we can do fast-rx anyway.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[fixed indentation on one line]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes rx for 4-addr packets in AP mode. These may be used for setting
up a 4-addr link for stations that are allowed to do so.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we now have the convenient helper to do so, actually adjust the
TSQ pacing shift for packets going out over a WiFi interface. This
significantly improves throughput for locally-originated TCP
connections. The default pacing shift of 10 corresponds to ~1ms of
queued packet data. Adjusting this to a shift of 8 (i.e. ~4ms) improves
1-hop throughput for ath9k by a factor of 3, whereas increasing it more
has diminishing returns.
Achieved throughput for different values of sk_pacing_shift (average of
5 iterations of 10-sec netperf runs to a host on the other side of the
WiFi hop):
sk_pacing_shift 10: 43.21 Mbps (pre-patch)
sk_pacing_shift 9: 78.17 Mbps
sk_pacing_shift 8: 123.94 Mbps
sk_pacing_shift 7: 128.31 Mbps
Latency for competing flows increases from ~3 ms to ~10 ms with this
change. This is about the same magnitude of queueing latency induced by
flows that are not originated on the WiFi device itself (and so are not
limited by TSQ).
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
-----BEGIN PGP SIGNATURE-----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=kwiY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes across the tree, the shortlog basically says it all:
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi channel scenarios, when disassociating from the AP before a
beacon was heard from the AP, it is not guaranteed that the virtual
interface is granted air time for the transmission of the
deauthentication frame. This in turn can lead to various issues as
the AP might never get the deauthentication frame.
To mitigate such possible issues, add a HW flag indicating that the
driver requires mac80211 to call the mgd_prep_tx() driver callback
to make sure that the virtual interface is granted immediate airtime
to be able to transmit the frame, in case that no beacon was heard
from the AP.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extracting the TID from the QOS header is common enough
to justify helper.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case an ADDBA request is received while there is already
an ongoing BA sessions with the same parameters, i.e., update
flow, an ADBBA response with decline status was sent twice. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some APs include a non global operating class in their extended channel
switch information element. In such a case, as the operating class is not
known, mac80211 would decide to disconnect.
However the specification states that the operating class needs to be
taken from Annex E, but it does not specify from which table it should be
taken, so it is valid for an AP to use a non global operating class.
To avoid possibly unneeded disconnection, in such a case ignore the
operating class and assume that the current band is used, and if the
resulting channel and band configuration is invalid disconnect.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sta_info_alloc can be called from atomic paths (such as RX path)
so we need to call pcpu_alloc with the correct gfp.
Fixes: c9c5962b56 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If sta_info_alloc fails after allocating the per CPU statistics,
they are not properly freed.
Fixes: c9c5962b56 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows users to get ack signal strength of
last transmitted frame.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch provides support to get ack signal in probe client response
and in station info from user.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
[squash in compilation fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pointer hrd is being initialized with a value that is never read
and re-assigned a little later, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
net/mac80211/tx.c:1924:24: warning: Value stored to 'hdr' during its
initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
gcc-8 warns about some obviously incorrect code:
net/mac80211/cfg.c: In function 'cfg80211_beacon_dup':
net/mac80211/cfg.c:2896:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
From the context, I conclude that we want to copy from beacon into
new_beacon, as we do in the rest of the function.
Cc: stable@vger.kernel.org
Fixes: 73da7d5bab ("mac80211: add channel switch command and beacon callbacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will add support to send an event to a userspace application
whenever station advertise its ht/vht opmode modification through
an action frame.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Might help one figure out why aqm drivers may fail to transmit
frames sometimes.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mesh TTL offset in Mesh Channel Switch Parameters element depends on
not only Secondary Channel Offset element, but also affected by
HT Control field and Wide Bandwidth Channel Switch element.
So use element structure to manipulate mesh channel swich param IE
after removing its constant attribution to correct the miscalculation.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One thing is notable: I applied two patches and later
reverted them - we'll get back to that once all the driver
situation is sorted out.
-----BEGIN PGP SIGNATURE-----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=M0gz
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-01-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have things all over the place, no point listing them.
One thing is notable: I applied two patches and later
reverted them - we'll get back to that once all the driver
situation is sorted out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are multiple mesh stations with the same MAC address,
they will both get confused and start throwing warnings.
Obviously in this case nothing can actually work anyway, so just
drop frames that look like they're from ourselves early on.
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit e937b8da5a.
Turns out that a new driver (mt76) is coming in through
Kalle's tree, and will conflict with this. It also has some
conflicting requirements, so we'll revisit this later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit b0d52ad821.
We need to revert the TXQ scheduling API due to conflicts
with a new driver, and this depends on that API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds airtime accounting and scheduling to the mac80211 TXQ
scheduler. A new hardware flag, AIRTIME_ACCOUNTING, is added that
drivers can set if they support reporting airtime usage of
transmissions. When this flag is set, mac80211 will expect the actual
airtime usage to be reported in the tx_time and rx_time fields of the
respective status structs.
When airtime information is present, mac80211 will schedule TXQs
(through ieee80211_next_txq()) in a way that enforces airtime fairness
between active stations. This scheduling works the same way as the ath9k
in-driver airtime fairness scheduling.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds an API to mac80211 to handle scheduling of TXQs and changes the
interface between driver and mac80211 for TXQ handling as follows:
- The wake_tx_queue callback interface no longer includes the TXQ. Instead,
the driver is expected to retrieve that from ieee80211_next_txq()
- Two new mac80211 functions are added: ieee80211_next_txq() and
ieee80211_schedule_txq(). The former returns the next TXQ that should be
scheduled, and is how the driver gets a queue to pull packets from. The
latter is called internally by mac80211 to start scheduling a queue, and
the driver is supposed to call it to re-schedule the TXQ after it is
finished pulling packets from it (unless the queue emptied).
The ath9k and ath10k drivers are changed to use the new API.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a key flag to indicates that the device only needs
MIC space and not a real MIC.
In such cases, keep the MIC zeroed for ease of debug.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While the change between 802.11-2012 and 802.11-2016 to move from
requiring APs to set the two top bits to now requiring them to be
cleared was apparently unintentional and will be fixed, clients
should either way assume that the top five bits are reserved and
ignore them.
Implement that in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the ieee80211_setup_sdata() we check if the interface type is valid
and, if not, call BUG(). This should never happen, but if there is
something wrong with the code, it will not be caught until the bug
happens when an interface is being set up. Calling BUG() is too
extreme for this and a WARN_ON() would be better used instead. Change
that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the restart flow enables RX back, and then proceeds
to tear down RX and TX aggregations.
The TX aggregation tear down calls synchronize_net(), which
waits for packet receiving to be done.
This is done for every session, while RX processing is already
active, and in some reproductions it takes up to 3 seconds.
Add a call once in the restart_work, before we have traffic
active again, and remove the subsequent calls when tearing
down the aggregation.
This requires to move down the code that turns off the
reconfig flag in order to be able to test it in
_ieee80211_stop_tx_ba_session().
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 2016 version of the spec is more generic about when the
AP should update the power management state of the peer:
the AP shall update the state based on any management or
data frames. This means that even non-bufferable management
frames should be looked at to update to maintain the power
management state of the peer.
This can avoid problematic cases for example if a station
disappears while being asleep and then re-appears. The AP
would remember it as in power save, but the Authentication
frame couldn't be used to set the peer as awake again.
Note that this issues wasn't really critical since at some
point (after the association) we would have removed the
station and created another one with all the states cleared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to set the buffer station extended capability
for TDLS links, with a new hardware flag indicating this.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
[change commit log/documentation wording]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to re-lookup the data structures now that
we actually get them immediately with from_timer(), just
avoid that. The struct has to be valid anyway, otherwise
the timer object itself would no longer be valid, and we
can't have a different version of the struct since only a
single session per TID is permitted.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in some cases I replaced "fall through on else" and
"otherwise fall through" comments with just a "fall through" comment,
which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to overlap between
commit 1281103770 ("mac80211: Simplify locking in ieee80211_sta_tear_down_BA_sessions()")
and the way that Luca modified
commit 72e2c3438b ("mac80211: tear down RX aggregations first")
when sending it upstream from Intel's internal tree, we get
the following warning:
WARNING: CPU: 0 PID: 5472 at net/mac80211/agg-tx.c:315 ___ieee80211_stop_tx_ba_session+0x158/0x1f0
since there's no appropriate locking around the call to
___ieee80211_stop_tx_ba_session; Sara's original just had
a call to the locked __ieee80211_stop_tx_ba_session (one
less underscore) but it looks like Luca modified both of
the calls when fixing it up for upstream, leading to the
problem at hand.
Move the locking appropriately to fix this problem.
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When doing HW restart we tear down aggregations.
Since at this point we are not TX'ing any aggregation, while
the peer is still sending RX aggregation over the air, it will
make sense to tear down the RX aggregations first.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous path metric update from RANN frame has not considered
the own link metric toward the transmitting mesh STA. Fix this.
Reported-by: Michael65535
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When connected to a QoS/WMM AP, mac80211 should use a QoS NDP
for probing it, instead of a regular non-QoS one, fix this.
Change all the drivers to *not* allow QoS NDP for now, even
though it looks like most of them should be OK with that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When deleting a station or otherwise tearing down all aggregation
sessions, make sure to delete requested but not yet started ones,
to avoid the following scenario:
* session is requested, added to tid_start_tx[]
* ieee80211_ba_session_work() runs, gets past BLOCK_BA check
* ieee80211_sta_tear_down_BA_sessions() runs, locks &sta->ampdu_mlme.mtx,
e.g. while deleting the station - deleting all active sessions
* ieee80211_ba_session_work() continues since tear down flushes it, and
calls ieee80211_tx_ba_session_handle_start() for the new session, arms
the timer for it
* station deletion continues to __cleanup_single_sta() and frees the
session struct, while the timer is armed
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
This removes the tid mapping array and expands the tid structures to
add a pointer back to the station, along with the tid index itself.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
[switch tid variables to u8, the valid range is 0-15 at most,
initialize tid_tx->sta/tid properly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
For the reinstall prevention, the code I had added compares the
whole key. It turns out though that iwlwifi firmware doesn't
provide the TKIP TX MIC key as it's not needed in client mode,
and thus the comparison will always return false.
For client mode, thus always zero out the TX MIC key part before
doing the comparison in order to avoid accepting the reinstall
of the key with identical encryption and RX MIC key, but not the
same TX MIC key (since the supplicant provides the real one.)
Fixes: fdf7cb4185 ("mac80211: accept key reinstall without changing anything")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben reported that when the user rate mask is rejected for not
matching any basic rate, the driver had already been configured.
This is clearly an oversight in my original change, fix this by
doing the validation before calling the driver.
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: e8e4f5280d ("mac80211: reject/clear user rate mask if not usable")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise we risk leaking information via timing side channel.
Fixes: fdf7cb4185 ("mac80211: accept key reinstall without changing anything")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a key is reinstalled we can reset the replay counters
etc. which can lead to nonce reuse and/or replay detection
being impossible, breaking security properties, as described
in the "KRACK attacks".
In particular, CVE-2017-13080 applies to GTK rekeying that
happened in firmware while the host is in D3, with the second
part of the attack being done after the host wakes up. In
this case, the wpa_supplicant mitigation isn't sufficient
since wpa_supplicant doesn't know the GTK material.
In case this happens, simply silently accept the new key
coming from userspace but don't take any action on it since
it's the same key; this keeps the PN replay counters intact.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code here (more or less accidentally) tracks the HT capability of
the AP when connected, and we found at least one AP that erroneously
toggles its 20/40 capability bit when changing between 20/40 MHz. The
connection to the AP is then broken because we set the 40 MHz disable
flag based on this, as soon as it switches to 20 MHz, but because the
flag then changed, we disconnect.
I'd be inclined to just ignore this issue, since we then reconnect
while the AP is in 20 MHz mode and never use 40 MHz with it again,
but this code is a bit strange anyway - we don't use the capabilities
for anything else.
Change the code to simply not track the HT capabilities at all, which
assumes that the AP at least sets 20/40 capability when operating in
40 MHz (or higher). If not, rate scaling might end up using only the
narrower bandwidth.
The new behaviour also mirrors what VHT does, where we only check the
VHT operation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Evidently this API is intended to be used to isolate against
API changes, so use it instead of accessing ->authsize.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When removing an AP VLAN interface, mac80211 currently purges
the entire TXQ for the AP interface. Fix this by using the FQ
API introduced in the previous patch to filter frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the aes_ccm.c and aes_gcm.c are almost line by line copy of
each other. This patch reduce code redundancy by moving the code in these
two files to crypto/aead_api.c to make it a higher level aead api. The
file aes_ccm.c and aes_gcm.c are removed and all the functions there are
now implemented in their headers using the newly added aead api.
Signed-off-by: Xiang Gao <qasdfgtyuiop@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This requires adding a pointer back
to the sta_info since container_of() can't resolve the sta_info.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Section 11.23.1 of 80211-2016 specification allows TDLS peers
to operate on wider bandwidths though they are connected to a BSS
which do not support wider bandwidth operations, provided both the
peers advertise wider bandwidth capabilities.
The existing logic considers the minimum of station's and AP's
capability for bandwidth computation. The same logic applies for
TDLS peers as well, this restricts operating on wider bandwidths
over a TDLS link when the peers are connected to legacy APs.
As an example, if 80Mhz VHT capable peers are connected to a 20Mhz
5 GHz AP, then as per the existing logic TDLS operation will be
restricted to 20Mhz.
Address this problem by not considering BSS capability in bandwidth
computation if the participating TDLS peers have wider bandwidth
capability.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
[lots of wording/typo fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes a station is added already in ASSOC state. For example,
in AP mode, when a client station didn't get assoc resp and sends
an assoc req again. If a station is inserted when its state is ASSOC
or higher, the min chandef and allow_p2p_go_ps should be recalculated
again after the insertion.
Before this patch the recalculation happened only in sta_info_move_state
which occurs before the insertion of the sta and thus even though
it calls ieee80211_recalc_min_chandef/_p2p_go_ps_allowed functions,
since sdata->local->sta_list is still empty at this point, it doesn't do
anything.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was created using the following spatch:
@find@
type S;
expression M, M2;
position p;
@@
offsetof(S, M) + sizeof(M2)@p
@script:python@
m << find.M;
m2 << find.M2;
@@
if not m2.endswith('-> ' + m):
cocci.include_match(False)
@change@
type find.S;
expression find.M, find.M2;
position find.p;
@@
-offsetof(S, M) + sizeof(M2)@p
+offsetofend(S, M)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simplify the locking in ieee80211_sta_tear_down_BA_sessions() and
lock sta->ampdu_mlme.mtx over the entire function instead of
locking/unlocking it for each TID etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add documentation to ieee80211_rx_ba_offl() function and, while at it,
rename the bit argument to tid, for consistency.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One of OCE's optimizations is acception of broadcast probe responses.
Accept broadcast probe responses but don't set
NL80211_EXT_FEATURE_ACCEPT_BCAST_PROBE_RESP. Because a device's firmware
may filter out the broadcast probe resp - drivers should set this flag.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[johannes: make accepting broadcast conditional on the nl80211 scan
flag that was added for that specific purpose]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to split off IEs from the ones obtained
from userspace, if they were already split off, so for
example IEs that went before HT don't have to be listed
again to go before VHT. Simplify the code here so it's
clearer.
While at it, also clarify the comments regarding the DMG
(60 GHz) elements.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an RX BA session is started by the driver, and it has to tell
mac80211 about it, the corresponding bit in tid_rx_manage_offl gets
set and the BA session work is scheduled. Upon testing this bit, it
will call __ieee80211_start_rx_ba_session(), thus deadlocking as it
already holds the ampdu_mlme.mtx, which that acquires again.
Fix this by adding ___ieee80211_start_rx_ba_session(), a version of
the function that requires the mutex already held.
Cc: stable@vger.kernel.org
Fixes: 699cb58c8a ("mac80211: manage RX BA session offload without SKB queue")
Reported-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7a7c0a6438 ("mac80211: fix TX aggregation start/stop callback race")
added a cancellation of the ampdu work after the loop that stopped the
Tx and Rx BA sessions. However, in some cases, e.g., during HW reconfig,
the low level driver might call mac80211 APIs to complete the stopping
of the BA sessions, which would queue the ampdu work to handle the actual
completion. This work needs to be performed as otherwise mac80211 data
structures would not be properly synced.
Fix this by checking if BA session STOP_CB bit is set after the BA session
cancellation and properly clean the session.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
[Johannes: the work isn't flushed because that could do other things we
don't want, and the locking situation isn't clear]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When HW ROC is supported it is possible that after the HW notified
that the ROC has started, the ROC was cancelled and another ROC was
added while the hw_roc_start worker is waiting on the mutex (since
cancelling the ROC and adding another one also holds the same mutex).
As a result, the hw_roc_start worker will continue to run after the
new ROC is added but before it is actually started by the HW.
This may result in notifying userspace that the ROC has started before
it actually does, or in case of management tx ROC, in an attempt to
tx while not on the right channel.
In addition, when the driver will notify mac80211 that the second ROC
has started, mac80211 will warn that this ROC has already been
notified.
Fix this by flushing the hw_roc_start work before cancelling an ROC.
Cc: stable@vger.kernel.org
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since drv_wake_tx_queue() is normally called in the TX path, which
is already in an RCU critical section, we should call it the same
way in the aggregation code path, so if the driver expects to be
able to use RCU, it'll already be protected without having to enter
a nested critical section.
Additionally, disable soft-IRQs, since not doing so could cause
issues in a driver that relies on them already being disabled like
in the other path.
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change adds null pointer check before dereferencing pointer dev on
netif_tx_start_all_queues() when an interface is added.
With iTXQ support, netif_tx_start_all_queues() is always called while
an interface is added. however, the netdev queues are not associated
and dev is null when the interface is either NL80211_IFTYPE_P2P_DEVICE
or NL80211_IFTYPE_NAN.
Signed-off-by: Chunho Lee <ch.lee@newracom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT MESH support was added, but the order of the IEs
wasn't enforced. Fix that.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Invoking ht_dbg() with too long of a string will print a warning.
Shorten the messages while retaining the printed patameters.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With TXQs, the AP_VLAN interfaces are resolved to their owner AP
interface when enqueuing the frame, which makes sense since the
frame really goes out on that as far as the driver is concerned.
However, this introduces a problem: frames to be encrypted with
a VLAN-specific GTK will now be encrypted with the AP GTK, since
the information about which virtual interface to use to select
the key is taken from the TXQ.
Fix this by preserving info->control.vif and using that in the
dequeue function. This now requires doing the driver-mapping
in the dequeue as well.
Since there's no way to filter the frames that are sitting on a
TXQ, drop all frames, which may affect other interfaces, when an
AP_VLAN is removed.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
this fix minor issue in the log message.
in ieee80211_rx_mgmt_assoc_resp function, when assigning the
reassoc value from the mgmt frame control:
ieee80211_is_reassoc_resp function need to be used, instead of
ieee80211_is_reassoc_req function.
Signed-off-by: Simon Dinkin <simon.dinkin@tandemg.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers handle rx buffer reordering internally (and by extension
handle also the rx ba session timer internally), but do not ofload the
addba/delba negotiation.
Add an api for these drivers to properly tear-down the ba session,
including sending a delba.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Avi fixes some fallout from my mac80211 RX flags changes
* Emmanuel fixes an issue with adhering to the spec, and
an oversight in the SMPS management code
* Jason's patch makes mac80211 use constant-time memory
comparisons for message authentication, to avoid having
potentially observable timing differences
* my fix makes mac80211 set the basic rates bitmap before
the channel so the next update to the driver has more
consistent data - this required another rework patch to
remove some useless 5/10 MHz code that can never be hit
-----BEGIN PGP SIGNATURE-----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=S5/1
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Some fixes:
* Avi fixes some fallout from my mac80211 RX flags changes
* Emmanuel fixes an issue with adhering to the spec, and
an oversight in the SMPS management code
* Jason's patch makes mac80211 use constant-time memory
comparisons for message authentication, to avoid having
potentially observable timing differences
* my fix makes mac80211 set the basic rates bitmap before
the channel so the next update to the driver has more
consistent data - this required another rework patch to
remove some useless 5/10 MHz code that can never be hit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is very useful to know what ampdu action is currently
happening. Add this information to the tracepoint.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 allows to modify the SMPS state of an AP both,
when it is started, and after it has been started. Such a
change will trigger an action frame to all the peers that
are currently connected, and will be remembered so that
new peers will get notified as soon as they connect (since
the SMPS setting in the beacon may not be the right one).
This means that we need to remember the SMPS state
currently requested as well as the SMPS state that was
configured initially (and advertised in the beacon).
The former is bss->req_smps and the latter is
sdata->smps_mode.
Initially, the AP interface could only be started with
SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF
always. Later, a nl80211 API was added to be able to start
an AP with a different AP mode. That code forgot to update
bss->req_smps and because of that, if the AP interface was
started with SMPS_DYNAMIC, we had:
sdata->smps_mode = SMPS_DYNAMIC
bss->req_smps = SMPS_OFF
That configuration made mac80211 think it needs to fire off
an action frame to any new station connecting to the AP in
order to let it know that the actual SMPS configuration is
SMPS_OFF.
Fix that by properly setting bss->req_smps in
ieee80211_start_ap.
Fixes: f699317487 ("mac80211: set smps_mode according to ap params")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, we enable all sorts of forgeries via timing attack.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 changes the channel, it also calls into the driver's
bss_info_changed() callback, e.g. with BSS_CHANGED_IDLE. The driver
may, like iwlwifi does, access more data from bss_info in that case
and iwlwifi accesses the basic_rates bitmap, but if changing from a
band with more (basic) rates to one with fewer, an out-of-bounds
access of the rate array may result.
While we can't avoid having invalid data at some point in time, we
can avoid having it while we call the driver - so set up all the
data before configuring the channel, and then apply it afterwards.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195677
Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Tested-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Debugged-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need for the station MLME code to handle bitrates for 5
or 10 MHz channels when it can't ever create such a configuration.
Remove the unnecessary code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver reports the rx timestamp at PLCP start, mac80211 can
only handle legacy encoding, but the code checks that the encoding
is not legacy. Fix this.
Fixes: da6a4352e7 ("mac80211: separate encoding/bandwidth from flags")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a peer sends a BAR frame with PM bit clear, we should
not modify its PM state as madated by the spec in
802.11-20012 10.2.1.2.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change to remove free_netdev() from ieee80211_if_free()
erroneously didn't add the necessary free_netdev() for when
ieee80211_if_free() is called directly in one place, rather
than as the priv_destructor. Add the missing call.
Fixes: cf124db566 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the SKB queue with the fake pkt_type for the
offloaded RX BA session management, also handle this with the
normal aggregation state machine worker. This also makes the
use of this more reliable since it gets rid of the allocation
of the fake skb.
Combined with the previous patch, this finally allows us to
get rid of the pkt_type hack entirely, so do that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This brings in commit 7a7c0a6438 ("mac80211: fix TX aggregation
start/stop callback race") to allow the follow-up cleanup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit enabling per-CPU station statistics, I inadvertedly
copy-pasted some code to update rx_packets and forgot to change it
to update rx_dropped_misc. Fix that.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=195953.
Fixes: c9c5962b56 ("mac80211: enable collecting station statistics per-CPU")
Reported-by: Petru-Florin Mihancea <petrum@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_tx_status() is only one of the possible ways a driver can
report a handled packet, some drivers call this for every packet while
others calls it rarely or never.
In order to invoke the TX LED in the non-status reporting cases this
patch pushes the call to ieee80211_led_tx() into
ieee80211_report_used_skb(), which is shared between the various code
paths.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This pattern was introduced a number of times in mac80211 just now,
and since it's present in a number of other places it makes sense
to add a little helper for it.
This just adds the helper and transforms the mac80211 code, a later
patch will transform other places.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When starting or stopping an aggregation session, one of the steps
is that the driver calls back to mac80211 that the start/stop can
proceed. This is handled by queueing up a fake SKB and processing
it from the normal iface/sdata work. Since this isn't flushed when
disassociating, the following race is possible:
* associate
* start aggregation session
* driver callback
* disassociate
* associate again to the same AP
* callback processing runs, leading to a WARN_ON() that
the TID hadn't requested aggregation
If the second association isn't to the same AP, there would only
be a message printed ("Could not find station: <addr>"), but the
same race could happen.
Fix this by not going the whole detour with a fake SKB etc. but
simply looking up the aggregation session in the driver callback,
marking it with a START_CB/STOP_CB bit and then scheduling the
regular aggregation work that will now process these bits as well.
This also simplifies the code and gets rid of the whole problem
with allocation failures of said skb, which could have left the
session in limbo.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support HT and VHT CSA, beacons and action frames must include the
corresponding IEs.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[make ieee80211_ie_build_wide_bw_cs() return void]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If userspace has flagged support for DFS earlier, then we can follow CSA
to DFS channels. So instead of rejecting the switch, allow it to happen
if the flag has been set during mesh setup.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clear the csa_ie in ieee80211_parse_ch_switch_ie() where the data
is filled in, rather than in each caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the Mesh Channel Switch Parameters (8.4.2.105) the reason is specified
to WLAN_REASON_MESH_CHAN_REGULATORY in the case that a regulatory
limitation was the cause for the switch. This means another station
detected a radar event.
Mark the channel as unusable if this happens.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
[sw: style cleanup, rebase]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CoDel can be too aggressive if a station sends at a very low rate,
leading reduced throughput. This gets worse the more stations are
present, as each station gets more bursty the longer the round-robin
scheduling between stations takes.
This adds dynamic adjustment of CoDel parameters per station. It uses
the rate selection information to estimate throughput and sets more
lenient CoDel parameters if the estimated throughput is below a
threshold (modified by the number of active stations).
A new callback is added that drivers can use to notify mac80211 about
changes in expected throughput, so the same adjustment can be made for
cards that implement rate control in firmware. Drivers that don't use
this will just get the default parameters.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[remove currently unnecessary EXPORT_SYMBOL, fix kernel-doc, remove
inline annotation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh forwarding path checks for address extension mode to fetch
appropriate proxied address and MPP address. Existing condition
that looks for 6 address format is not strict enough so that
frames with improper values are processed and invalid entries
are added into MPP table. Fix that by adding a stricter check before
processing the packet.
Per IEEE Std 802.11s-2011 spec. Table 7-6g1 lists address extension
mode 0x3 as reserved one. And also Table Table 9-13 does not specify
0x3 as valid address field.
Fixes: 9b395bc3be ("mac80211: verify that skb data is present")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When VHT IBSS support was added, the size of the extra elements
wasn't considered in ieee80211_ibss_build_presp(), which makes
it possible that it would overrun the allocated buffer. Fix it
by allocating the necessary space.
Fixes: abcff6ef01 ("mac80211: add VHT support for IBSS")
Reported-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If ieee80211_hw_restart() is called during authentication, the
authentication process will continue, causing the driver to be called
in a wrong state. This ultimately causes an oops in the iwlwifi
driver (at least).
This fixes bugzilla 195299 partly.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195299
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.
The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.
An example scenario is as below:
In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif
ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
(Reason: 3=DEAUTH_LEAVING)
WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
[<bf77272c>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211]))
[<bf73cc50>] (nl80211_new_station [cfg80211])
Unable to handle kernel NULL pointer dereference at virtual
address 00000014
pgd = d5f4c000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
PC is at sta_info_alloc+0x380/0x3fc [mac80211]
LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
[<bf772738>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211])
[<bf73cc50>] (nl80211_new_station [cfg80211]))
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows the driver to pass in struct ieee80211_tx_status directly.
Make ieee80211_tx_status_noskb a wrapper around it.
As with ieee80211_tx_status_noskb, there is no _ni variant of this call,
because it probably won't be needed.
Even if the driver won't provide any extra status info other than what's
in struct ieee80211_tx_info already, it can optimize status reporting
this way by passing in the station pointer.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[use C99 initializers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename .tx_status_noskb to .tx_status_ext and pass a new on-stack
struct ieee80211_tx_status instead of struct ieee80211_tx_info.
This struct can be used to pass extra information, e.g. for dynamic tx
power control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of hand-coding the bit manipulations, use the bitfield
macros to generate the code for the encoded bitrate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This field will need to be used again for HE, so rename it now.
Again, mostly done with this spatch:
@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The multicast variable in the ieee80211_accept_frame() function is
treated as a boolean, but defined as int. Fix that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least on iwlwifi, sometimes lockdep complains that we can
lock
chanctx_mtx -> mvm.mutex -> iflist_mtx
(due to iterate_interfaces)
and
iflist_mtx -> chanctx_mtx
Remove the latter dependency in mac80211 by using the RTNL
that we already hold in one case, and can relatively easily
achieve in the other case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_frame_acked is called when a frame is acked by
the peer. In case this is a management frame, we check
if this an SMPS frame, in which case we can update our
antenna configuration.
When we parse the management frame we look at the category
in case it is an action frame. That byte sits after the IV
in case the frame was encrypted. This means that if the
frame was encrypted, we basically look at the IV instead
of looking at the category. It is then theorically
possible that we think that an SMPS action frame was acked
where really we had another frame that was encrypted.
Since the only management frame whose ack needs to be
tracked is the SMPS action frame, and that frame is not
a robust management frame, it will never be encrypted.
The easiest way to fix this problem is then to not look
at frames that were encrypted.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The monitor mode delivery logic makes it hard to add any
kind of filtering in an efficient way, because the monitor
SKB is created first and then passed to all interfaces.
Rewrite the logic to create the monitor SKB the first time
it's actually needed, and then keep delivering it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
AP/AP_VLAN modes don't accept any real 802.11 multicast data
frames, but since they do need to accept broadcast management
frames the same is currently permitted for data frames. This
opens a security problem because such frames would be decrypted
with the GTK, and could even contain unicast L3 frames.
Since the spec says that ToDS frames must always have the BSSID
as the RA (addr1), reject any other data frames.
The problem was originally reported in "Predicting, Decrypting,
and Abusing WPA2/802.11 Group Keys" at usenix
https://www.usenix.org/conference/usenixsecurity16/technical-sessions/presentation/vanhoef
and brought to my attention by Jouni.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
--
Dave, I didn't want to send you a new pull request for a single
commit yet again - can you apply this one patch as is?
Signed-off-by: David S. Miller <davem@davemloft.net>
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
-----BEGIN PGP SIGNATURE-----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=f4VT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cfg80211_chandef_create() expects an 'enum nl80211_channel_type' as
channel type however in ieee80211_sta_join_ibss()
NL80211_CHAN_WIDTH_20_NOHT is passed in two occasions, which is of
the enum type 'nl80211_chan_width'. Change the value to NL80211_CHAN_NO_HT
(20 MHz, non-HT channel) of the channel type enum.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In addition to keeping monitor interfaces on the regular list of
interfaces, keep those that are up and not in cooked mode on a
separate list. This saves having to iterate all interfaces when
delivering to monitor interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two bugs in the follow-MAC code:
* it treats the radiotap header as the 802.11 header
(therefore it can't possibly work)
* it doesn't verify that the skb data it accesses is actually
present in the header, which is mitigated by the first point
Fix this by moving all of this out into a separate function.
This function copies the data it needs using skb_copy_bits()
to make sure it can be accessed if it's paged, and offsets
that by the possibly present vendor radiotap header.
This also makes all those conditions more readable.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the code to have common code for changing monitor
options when adding and changing virtual interfaces. This
will make it easier to add BPF filters to both paths. Note
that this code carefully checks the error conditions first
and only then applies the changes, to guarantee atomicity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MU-MIMO monitor follow functionality is broken because it
doesn't clear the MU-MIMO owner even if both follow features
are disabled. Fix that, and while at it move the code into a
new helper function. Call this also when creating a new monitor
interface to prepare for an upcoming cfg80211 change allowing
that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing monitor parameters, not setting the MU-MIMO attributes
should mean that they're not changed - it's documented that to turn
the feature off it's necessary to set all-zero group membership and
an invalid follow-address. This isn't implemented.
Fix this by making the parameters pointers, stop reusing the macaddr
struct member, and documenting that NULL pointers mean unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of dropping such frames only when removing the
monitor info, drop them earlier (keeping the warning)
and simplify removing monitor info. While at it, make
that function return void.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When clang detects a non-boolean constant in a logical operation it
generates a 'constant-logical-operand' warning. In
ieee80211_try_rate_control_ops_get() the result of strlen(<const str>)
is used in a logical operation, clang resolves the expression to an
(integer) constant at compile time when clang's builtin strlen function
is used.
Change the condition to check for strlen() > 0 to make the constant
operand boolean and thus avoid the warning.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When internal mac80211 TXQs aren't supported, netdev queues must
always started out started even when driver queues are stopped
while the interface is added. This is necessary because with the
internal TXQ support netdev queues are never stopped and packet
scheduling/dropping is done in mac80211.
Cc: stable@vger.kernel.org # 4.9+
Fixes: 80a83cfc43 ("mac80211: skip netdev queue control with software queuing")
Reported-and-tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On some practical cases, it is useful to drop new node in the distance.
Because mesh metric is calculated with hop count and without RSSI
information, a node far from local peer and near to destination node
could be used as best path.
For example, the nodes are located in linear. Distance of 0 - 1 and
1 - 2 and 2 - 3 is 20meters. 0 to 3 signal is very weak.
0 --- 1 --- 2 --- 3
Though most robust path from 0 to 3 is 0 -> 1 -> 2 -> 3,
unfortunately, node 0 could recognize node 3 as neighbor. Then node 3
could be next of node 0. This patch aims to avoid such a case.
[Johannes:]
Dropping the node entirely isn't ideal, but at least with encryption
there will be a limit on # of keys the hardware can deal with, and
there might also be a limit on the number of stations it supports.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use setup_timer() and setup_deferrable_timer() to set the data and
function timer fields. It makes the code cleaner and will allow for
easier change of the timer struct internals.
Signed-off-by: Ondřej Lysoněk <ondrej.lysonek@seznam.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <linux-wireless@vger.kernel.org>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user rate mask results in no (basic) rates being usable,
clear it. Also, if we're already operating when it's set, reject
it instead.
Technically, selecting basic rates as the criterion is a bit too
restrictive, but calculating the usable rates over all stations
(e.g. in AP mode) is harder, and all stations must support the
basic rates. Similarly, in client mode, the basic rates will be
used anyway for control frames.
This fixes the "no supported rates (...) in rate_mask ..." warning
that occurs on TX when you've selected a rate mask that's not
compatible with the connection (e.g. an AP that enables only the
rates 36, 48, 54 and you've selected only 6, 9, 12.)
Reported-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There isn't really much harm in not ignoring, since it doesn't
represent a valid rate, but since we already ignore the HT one
also ignore VHT. Also simplify the code a bit.
Fix a typo in the related comment (pointed out by Arend) while
at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use setup_timer() and setup_deferrable_timer() to set the data and
function timer fields. It makes the code cleaner and will allow for
easier change of the timer struct internals.
Signed-off-by: Ondřej Lysoněk <ondrej.lysonek@seznam.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <linux-wireless@vger.kernel.org>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh failure average never be more than 100. Only in case of
fixed path, average will be more than threshold limit (95%).
With recent EWMA changes it may go upto 99 as it is scaled to
100. It make sense to return maximum metric when average is
greater than threshold limit.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't really need three different bits for each, since the
types are mutually exclusive. Use just two bits for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This matches the spec, and otherwise things are really
confusing with the next patch adding CCFS2.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When disassociation happens only numeric reason is printed
in ieee80211_rx_mgmt_disassoc(). Add text variant, too.
Signed-off-by: Arkadiusz Miśkiewicz <arekm@maven.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support .set_cqm_rssi_range_config if the beacons are available for
processing in mac80211. There's no reason that this couldn't be
offloaded by mac80211-based drivers but there's no driver method for
that added in this patch.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As moving average is not considering fractional part, it will
get stuck at the same level after certain state. For example,
with current values, it can get stuck at 96. Fortunately the
current threshold 95%, but if it were increased to 96 or more
mesh paths would never be deactivated. Fix failure average
movement by using EWMA helpers, which does take into account
fractional parts.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
[johannes: pick a larger EWMA factor for more precision with
the limited range that we will feed into it, adjust to new API]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
We don't actually need the full rculist.h header in sched.h anymore,
we will be able to include the smaller rcupdate.h header instead.
But first update code that relied on the implicit header inclusion.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Declaring the factor is counter-intuitive, and people are prone
to using small(-ish) values even when that makes no sense.
Change the DECLARE_EWMA() macro to take the fractional precision,
in bits, rather than a factor, and update all users.
While at it, add some more documentation.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* use a valid hrtimer clock ID in mac80211_hwsim
* don't reorder frames prior to BA session
* flush a delayed work at suspend so the state is all valid before
suspend/resume
* fix packet statistics in fast-RX, the RX packets
counter increment was simply missing
* don't try to re-transmit filtered frames in an aggregation session
* shorten (for tracing) a debug message
* typo fix in another debug message
* fix nul-termination with HWSIM_ATTR_RADIO_NAME in hwsim
* fix mgmt RX processing when station is looked up by driver/device
-----BEGIN PGP SIGNATURE-----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=wths
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-02-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
First round of fixes - details in the commits:
* use a valid hrtimer clock ID in mac80211_hwsim
* don't reorder frames prior to BA session
* flush a delayed work at suspend so the state is all valid before
suspend/resume
* fix packet statistics in fast-RX, the RX packets
counter increment was simply missing
* don't try to re-transmit filtered frames in an aggregation session
* shorten (for tracing) a debug message
* typo fix in another debug message
* fix nul-termination with HWSIM_ATTR_RADIO_NAME in hwsim
* fix mgmt RX processing when station is looked up by driver/device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IDR rewrite from Matthew Wilcox:
"The most significant part of the following is the patch to rewrite the
IDR & IDA to be clients of the radix tree. But there's much more,
including an enhancement of the IDA to be significantly more space
efficient, an IDR & IDA test suite, some improvements to the IDR API
(and driver changes to take advantage of those improvements), several
improvements to the radix tree test suite and RCU annotations.
The IDR & IDA rewrite had a good spin in linux-next and Andrew's tree
for most of the last cycle. Coupled with the IDR test suite, I feel
pretty confident that any remaining bugs are quite hard to hit. 0-day
did a great job of watching my git tree and pointing out problems; as
it hit them, I added new test-cases to be sure not to be caught the
same way twice"
Willy goes on to expand a bit on the IDR rewrite rationale:
"The radix tree and the IDR use very similar data structures.
Merging the two codebases lets us share the memory allocation pools,
and results in a net deletion of 500 lines of code. It also opens up
the possibility of exposing more of the features of the radix tree to
users of the IDR (and I have some interesting patches along those
lines waiting for 4.12)
It also shrinks the size of the 'struct idr' from 40 bytes to 24 which
will shrink a fair few data structures that embed an IDR"
* 'idr-4.11' of git://git.infradead.org/users/willy/linux-dax: (32 commits)
radix tree test suite: Add config option for map shift
idr: Add missing __rcu annotations
radix-tree: Fix __rcu annotations
radix-tree: Add rcu_dereference and rcu_assign_pointer calls
radix tree test suite: Run iteration tests for longer
radix tree test suite: Fix split/join memory leaks
radix tree test suite: Fix leaks in regression2.c
radix tree test suite: Fix leaky tests
radix tree test suite: Enable address sanitizer
radix_tree_iter_resume: Fix out of bounds error
radix-tree: Store a pointer to the root in each node
radix-tree: Chain preallocated nodes through ->parent
radix tree test suite: Dial down verbosity with -v
radix tree test suite: Introduce kmalloc_verbose
idr: Return the deleted entry from idr_remove
radix tree test suite: Build separate binaries for some tests
ida: Use exceptional entries for small IDAs
ida: Move ida_bitmap to a percpu variable
Reimplement IDR and IDA using the radix tree
radix-tree: Add radix_tree_iter_delete
...
When I originally introduced using the driver-indicated station as an
optimisation to avoid the hashtable lookup/iteration, of course it
wasn't intended to really functionally change anything.
I neglected, however, to take into account VLAN interfaces, which have
the property that management and data frames are handled differently:
data frames go directly to the station and the VLAN while management
frames continue to be processed over the underlying/associated AP-type
interface. As a consequence, when a driver used this optimisation for
management frames and the user enabled VLANs, my change broke things
since any management frames, particularly disassoc/deauth, were missed
by hostapd.
Fix this by restoring the original code path for non-data frames, they
aren't critical for performance to begin with.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194713.
Big thanks goes to Jarek who bisected the issue and provided a very
detailed bug report, including the crucial information that he was
using VLANs in his configuration.
Cc: stable@vger.kernel.org
Fixes: 771e846bea9e ("mac80211: allow passing transmitter station on RX")
Reported-and-tested-by: Jarek Kamiński <jarek@freeside.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix typos and add the following to the scripts/spelling.txt:
swith||switch
swithable||switchable
swithed||switched
swithing||switching
While we are here, fix the "update" to "updates" in the touched hunk in
drivers/net/wireless/marvell/mwifiex/wmm.c.
Link: http://lkml.kernel.org/r/1481573103-11329-2-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tracing is limited to 100 characters and this message passes
the limit when there are a few buffered frames. Shorten it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi now supports RSS and can't let mac80211 track the
PS state based on the Rx frames since they can come out of
order. iwlwifi is now advertising AP_LINK_PS, and uses
explicit notifications to teach mac80211 about the PS state
of the stations and the PS poll / uAPSD trigger frames
coming our way from the peers.
Because of that, the TIM stopped being maintained in
mac80211. I tried to fix this in commit c68df2e7be
("mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
but that was later reverted by Felix in commit 6c18a6b4e7
("Revert "mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
since it broke drivers that do not implement set_tim.
Since none of the drivers that set AP_LINK_PS have the
set_tim() handler set besides iwlwifi, I can bail out in
__sta_info_recalc_tim if AP_LINK_PS AND .set_tim is not
implemented.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When running a BA session, the driver (or the hardware) already takes
care of retransmitting failed frames, since it has to keep the receiver
reorder window in sync.
Adding another layer of retransmit around that does not improve
anything. In fact, it can only lead to some strong reordering with huge
latency.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When RX aggregation starts, transmitter may continue send frames
with SN smaller than SSN until the AddBA response is received.
However, the reorder buffer is already initialized at this point,
which will cause the drop of such frames as duplicates since the
head SN of the reorder buffer is set to the SSN, which is bigger.
Cc: stable@vger.kernel.org
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The issue was found when entering suspend and resume.
It triggers a warning in:
mac80211/key.c: ieee80211_enable_keys()
...
WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt ||
sdata->crypto_tx_tailroom_pending_dec);
...
It points out sdata->crypto_tx_tailroom_pending_dec isn't cleaned up successfully
in a delayed_work during suspend. Add a flush_delayed_work to fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding per-CPU statistics, which added statistics back
to mac80211 for the fast-RX path, I evidently forgot to add
the "stats->packets++" line. The reason for that is likely
that I didn't see it since it's done in defragmentation for
the regular RX path.
Add the missing line to properly count received packets in
the fast-RX case.
Fixes: c9c5962b56 ("mac80211: enable collecting station statistics per-CPU")
Reported-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is a relatively common idiom (8 instances) to first look up an IDR
entry, and then remove it from the tree if it is found, possibly doing
further operations upon the entry afterwards. If we change idr_remove()
to return the removed object, all of these users can save themselves a
walk of the IDR tree.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sqkq
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more updates:
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing IBSS capability flag during capability init as it needs
to be inserted into the generated beacon in order for CSA to work.
Fixes: cd7760e62c ("mac80211: add support for CSA in IBSS mode")
Signed-off-by: Piotr Gawlowicz <gawlowicz@tkn.tu-berlin.de>
Signed-off-by: Mikołaj Chwalisz <chwalisz@tkn.tu-berlin.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nl80211_nan_dual_band_conf enumeration doesn't make much sense.
The default value is assigned to a bit, which makes it weird if the
default bit and other bits are set at the same time.
To improve this, get rid of NL80211_NAN_BAND_DEFAULT and add a wiphy
configuration to let the drivers define which bands are supported.
This is exposed to the userspace, which then can make a decision on
which band(s) to use. Additionally, rename all "dual_band" elements
to "bands", to make things clearer.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend ieee80211_cqm_rssi_notify with a rssi_level parameter so that
this information can be passed to netlink clients in the next patch, if
available. Most drivers will have this value at hand. wl1251 receives
events from the firmware that only tell it whether latest measurement
is above or below threshold so we don't pass any value at this time
(parameter is 0).
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
kmalloc() can fail. Also let's move the allocation out of the
declaration block so it's easier to read.
Fixes: 4a5eccaa93 ("mac80211: Show pending txqlen in debugfs.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of open coding the CMAC algorithm in the mac80211 driver using
byte wide xors and calls into the crypto layer for each block of data,
instantiate a cmac(aes) synchronous hash and pass all the data into it
directly. This does not only simplify the code, it also allows the use
of more efficient and more secure implementations, especially on
platforms where SIMD ciphers have a considerable setup cost.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Switch the FILS AEAD code to use a cmac(aes) shash instantiated by the
crypto API rather than reusing the open coded implementation in
aes_cmac_vector(). This makes the code more understandable, and allows
platforms to implement cmac(aes) in a more secure (*) and efficient way
than is typically possible when using the AES cipher directly.
So replace the crypto_cipher by a crypto_shash, and update the aes_s2v()
routine to call the shash interface directly.
* In particular, the generic table based AES implementation is sensitive
to known-plaintext timing attacks on the key, to which AES based MAC
algorithms are especially vulnerable, given that their plaintext is not
usually secret. Time invariant alternatives are available (e.g., based
on SIMD algorithms), but may incur a setup cost that is prohibitive when
operating on a single block at a time, which is why they don't usually
expose the cipher API.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow these files were never present or lost, but the code
is there and they seem somewhat useful, so add them back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function ieee80211_ie_split_vendor doesn't return 0 on errors. Instead
it returns any offset < ielen when WLAN_EID_VENDOR_SPECIFIC is found. The
return value in mesh_add_vendor_ies must therefore be checked against
ifmsh->ie_len and not 0. Otherwise all ifmsh->ie starting with
WLAN_EID_VENDOR_SPECIFIC will be rejected.
Fixes: 082ebb0c25 ("mac80211: fix mesh beacon format")
Signed-off-by: Thorsten Horstmann <thorsten@defutech.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[sven@narfation.org: Add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
