* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
When read valid tx/rx chains from EEPROM, there is a bug to use the
tx chain value for both tx and rx, the result of this cause low
receive throughput on 1x2 devices becuase rx will only utilize single
chain instead of two chains
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_reset must be called with sc->lock. Since the tx queue
watchdog runs in a workqueue and accesses sc, it's appropriate
to just take the lock over the whole function.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.
In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.
Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
We need to release_firmware() in order not to leak memory.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the case of alloc_netdev_mq failure and kmalloc failure,
current implementation returns ERR_PTR(0).
As a result, the caller of iwm_if_alloc does not catch the error by IS_ERR
macro. Fix it by setting proper error code for ret variable in the failure
cases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pcmcia_request_irq() and pcmcia_enable_device() are intended
to be called from process context (first function allocate memory
with GFP_KERNEL, second take a mutex). We can not take spin lock
and call them.
It's safe to move spin lock after pcmcia_enable_device() as we
still hold off IRQ until dev->base_addr is 0 and driver will
not proceed with interrupts when is not ready.
Patch resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=643758
Reported-and-tested-by: rbugz@biobind.com
Cc: stable@kernel.org # 2.6.34+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an attempt to fix a long standing open bug:
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1334
The interrupt handler checks for INTA being -1, apparently that means that the
hardware is gone. But the interrupt handler defers actual interrupt processing
to a tasklet. By the time the tasklet is run and checks INTA again, the
hardware might be gone and INTA be -1, which confuses the driver because all
event bits are set.
The patch applies to 2.6.37.
Signed-off-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."
Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.
Yup, it's the exact opposite!
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmask value along with other configuration has to be set
on the target for packet injection. Fix this and also move the monitor
interface addition before the channel set segment to ensure that
the opmode is updated properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.
Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
USB devices do not require the chip test routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Fix test in lbs_spi_thread(). down_interruptible() can return -EINTR, but
not EINTR.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To inject a packet in monitor mode, a dummy station has
to be associated with the monitor interface in the target.
Failing to do this would result in a firmware crash on the device.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_eeprom_mode_from_channel() returns -1 on error but we're storing
the result in "ee_mode" which is an unsigned char. This breaks the
error handling. This patch makes "ee_mode" an int.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some obvious looking dead code and rename few functions
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 0ce3bcfc84.
Event though with the above commit we obtain the configured DTIM period
from the AP rather than always hardcoding it to '1', this seems to cause
problems under the following scenarios:
* Preventing association with broken AP's
* Adds latency in roaming
So its better to always use the safe value of '1' for dtim period
Cc: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An Rx DMA descriptor can have multiple error bits set, and some error
bits (e.g. MIC failure) are filtered by the driver based on other criteria.
Remove the 'else' in various error bit checks so that all error information
is properly passed to the driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And add the copyright/license header.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When returning to the operating channel, a full HW
reset has to be done instead of a fast channel change.
Since sw_scan_complete() is called after the config() call for the
home channel, we end up doing a FCC. Fix this issue by checking
the OFFCHANNEL flag to determine FCC.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device has to be reset when a FATAL event is received.
Not doing so would leave the card in a non-working state.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to lock the various work cancellation
calls. This will be helpful when handling FATAL events.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing a channel change, the pending URBs have to be killed
properly on calling htc_stop().
This fixes the probe response timeout seen when sending UDP traffic at
a high rate and running background scan at the same time.
Cc: stable <stable@kernel.org>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some minor clean ups in assigning values to beacon config parameters
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment doesn't match the code anymore. Fix that.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the last user of intf->lock is gone we can safely remove it.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of protecting delayed_flags with a spinlock use atomic bitops to
make the code more readable.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx desciptor already gets initialized to 0. Hence, there's no need
to explicitly assign 0 to mpdu_density here.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Backtrace:
rt2800usb_write_tx_data
rt2x00queue_write_tx_frame
rt2x00mac_tx
invoke_tx_handlers
__ieee80211_tx
ieee80211_tx
virt_to_head_page
ieee80211_xmit
ieee80211_tx_skb
ieee80211_scan_work
schedule
ieee80211_scan_work
process_one_work
...
It tried to expand the skb past it's end using skb_put. So I replaced it
with a call to skb_padto, which takes the issue into account.
Signed-off-by: Ismael Luceno <ismael.luceno@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some pointer errors in the various calls to memcpy, memset and memmove.
Although none of these errors are fatal (the expression used now results in
the same pointer value) it is better to use the proper expression.
All errors are having to deal with arrays.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac field of the rt2x00_intf structure is written to once and used
twice. In both these uses the mac address is available via other means.
Remove this field as it does not appear to be necessary.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bssid field in struct rt2x00_intf is only written to once, and is
never read from.
Remove this field, as it appears to not be needed.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When DRIVER_REQUIRE_TXSTATUS_FIFO is set, intialize the
txstatus_fifo, but initialize rt2x00dev->txstatus_tasklet
only when both DRIVER_REQUIRE_TXSTATUS_FIFO and
rt2x00dev->ops->lib->txstatus_tasklet are set.
This allows the txstatus_fifo to be used by rt2800usb which
does not use txstatus_tasklet.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps some common code-paths which are
shared between (re-)initialization and suspend/resume
subroutines. It also adds some helpful comments
about quirks and associated difficulties.
It's quite big, but it should fix#25382:
<https://bugzilla.kernel.org/show_bug.cgi?id=25382>
And hopefully the code is robust enough to deal with
all possible suspend/resume scenarios without requiring
the user to do any sort of manual and possibly
dangerous work.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By removing two "safety" msleeps (and an echo nop), the
channel change delay is effectively halved. Previously,
the delay could be as long as 260 ms and the device
could not go off-channel without risking to miss the
next DTIM beacon [interval ~307 ms].
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
